Skip to content

Latest commit

 

History

History
153 lines (125 loc) · 5.49 KB

bosh_install.md

File metadata and controls

153 lines (125 loc) · 5.49 KB
Raw

Installing BOSH

There is nothing special about installing BOSH for the Cloud Foundry RabbitMQ deployment. The following are reasonably generic but by no means intended to be a canonical installation guide. Use at your own risk. Equally, if you are familiar with BOSH and/or already have your own BOSH deployment, you may not find much of interest on this page.

Set up microbosh

Follow the instructions to the point where you have a running microbosh. Those are AWS based to a degree. For vSphere, these blog entries seem reasonable.

Create & upload a release

In your inception VM...

  • cd ~/workspace/deployments-aws/<name>
  • git clone git@github.com:pivotal-cf/cf-rabbitmq-release.git && cd cf-rabbitmq-release
  • bosh create release --with-tarball (at the prompt, name the release cf-rabbitmq)
  • bosh upload release

Create a deployment and deploy it

AWS

  • edit manifests/cf-rabbitmq-aws.yml

    • set the director_uuid to the value shown by bosh status --uuid
    • set networks.subnets.cloud_properties.subnet to the value of vpc.subnets.cf1 in aws_vpc_receipt.yml

  • update cf domain in the properties section , hint search for your_cc_endpoint.com

  • update cf related passwords in properties section such as:

    • properties.cf.nats.username/password
    • properties.uaa_client.username/password

  • to change the rabbitmq administrator username / password change:

    • properties.rabbitmq-server.administrators.broker.username/password
    • properties.rabbitmq-broker.administrators.username/password

  • add ssl certificates to the following sections if required:

    • properties.rabbitmq-broker.rabbitmq.ssl
    • properties.rabbitmq-server.ssl

  • to configure rabbitmq plugins edit:

    • properties.rabbitmq-server.plugins

    For example:

      properties:
  	rabbitmq-server:
  		plugins:
  		- rabbitmq_management
  		- rabbitmq_mqtt
  		- rabbitmq_stomp

  • to enable TLSv1.0 (required for JDK 6 support) add the following:

      properties
    rabbitmq-server:
      ssl:
  	  security_options: 
  	  - enable_tls1_0

  • make any required ip changes to the manifest depending on your AWS setup

  • set the deployment manifest bosh deployment manifests/cf-rabbitmq-aws.yml

  • deploy bosh deploy

  • run bosh vms or similar to look at the status of the deployment

Note: TLS versions 1.1 and 1.2 are enabled by default.

vSphere

For vSphere, you similarly want to prepare a deployment manifest. Essentially it's a broadly similar process to AWS with differences in particular to the cloud_properties entries. For example, in compilation with AWS you're likely to have something like:

compilation:
  workers: 4
  network: cf1
  reuse_compilation_vms: true
  cloud_properties:
    instance_type: c1.medium
    availability_zone: us-east-1c

whereas in vSphere, you're going to have something like:

compilation:
  workers: 4
  network: cf1
  cloud_properties:
    ram: 1024
    disk: 4096
    cpu: 2

On the whole, because vSphere isn't relying on arbitrary VPC configurations and network names that have been decided for you by bosh aws bootstrap and friends, it's much more logical - you can give the networks names you want, etc. The network settings are obviously very important to get right - the best source of info will be the vSphere client, but you can basically figure out most things from judicious use of ifconfig, route and ping should you have access to some sort of inception VM on the same network. This blog post is worth reading regarding vSphere client and BOSH.

Here's an example network configuration:

networks:
- name: default
  subnets:
  - range: 10.150.28.0/22
    reserved:
    - 10.150.28.1 - 10.150.28.255
    - 10.150.29.1 - 10.150.29.50
    - 10.150.29.70 - 10.150.29.255
    - 10.150.30.1 - 10.150.30.255
    - 10.150.31.1 - 10.150.31.252
    static:
    - 10.150.29.51 - 10.150.29.69
    gateway: 10.150.31.253
    dns:
    - 10.17.193.1 # use your own DNS server IP
    - 10.17.193.2 # here too :)
    cloud_properties:
      name: "VM Network" #the VLAN that you are deploying BOSH to - provisioned on your vCenter

The range was determined from the destination address and netmask of the non-default-route entries reported by route -n on the inception VM (the /22 is CIDR representation of the 255.255.252.0 netmask). It should be evident in the vSphere configuration too.

vSphere should be able to tell us which IP ranges are in use. Alternatively, we can probe the network with ping -c 2 -b 10.150.31.255 (the latter being the broadcast address of the 10.150.28.0/22 network).

Pick a range that doesn't overlap with the addresses in use and make that the static range. The reserved range then is really just the full range minus the static range.

The gateway address is taken from the default route entries reported by route -n on the inception VM. It should also be available in vSphere.

The dns addresses were taken from /etc/resolv.conf on the inception VM; this information should also be available in vSphere.

The network name was taken from vSphere.