Disclaimer: This is not an official Google product.
This daemon has a very specific purpose: to give the same IPv6 prefix /64 to several network interfaces using radvd without creating L2 bridge and without need to configure DHCPv6. It's designed to be used together with ndppd for case if ISP gives single /64 without delegating a bigger prefix to your router.
On 2017-08-07 this functionality was merged into ndppd itself. However, there are several caveats:
- If ndppd crashes for whatever reason, routes which it adds are never deleted. If this risk is unacceptable for you, use ndprbrd until this issue is fixed.
- There was no new release of ndppd yet, so your favorite distro may have a version which doesn't support it. In that case you need to either still use ndprbrd, or build ndppd from git master.
An example ndppd config with this functionality enabled:
proxy eth0 {
autowire yes
rule 2001:db8:1:2::/64 {
iface eth1
}
rule 2001:db8:1:2::/64 {
iface eth2
}
}
proxy eth1 {
autowire yes
rule 2001:db8:1:2::/64 {
iface eth0
}
rule 2001:db8:1:2::/64 {
iface eth2
}
}
proxy eth2 {
autowire yes
rule 2001:db8:1:2::/64 {
iface eth0
}
rule 2001:db8:1:2::/64 {
iface eth1
}
}
If new ndppd is enough for you, you can stop reading now.
Below are 2 sample setups - the simple one which doesn't need ndprbrd, and the more complicated one which makes use of it. The simple setup sets the base for the more complicated one.
+-------------------+
| ISP |
| radvd announces |
| 2001:db8:1:2::/64 |
+---------+---------+
|
|
| eth0
| addr 2001:db8:1:2::42
| default route via link-local address
| ndppd answers to NDP solicitations, so ISP thinks that the whole 2001:db8:1:2::/64 is here
+------+------+
| My router |
+------+------+
| eth1
| radvd announces 2001:db8:1:2::/64
| route to 2001:db8:1:2::/64
|
|
+--+--+
| LAN |
+-----+
- A packet comes from internet to 2001:db8:1:2::33
- ISP sends NDP neigbor solicitation to the wire
- ndppd sees it, and replies to it
- depending on whether
autoorstaticis used, ndppd behaves slightly differently, but I don't want to go to such details. Both modes work.
- depending on whether
- Router sends solicitation to LAN, gets response (neighbor advertisement), sends packets to there, and everyone is happy.
+-------------------+
| ISP |
| radvd announces |
| 2001:db8:1:2::/64 |
+---------+---------+
|
|
| eth0
| addr 2001:db8:1:2::42
| default route via link-local address
| ndppd answers to NDP solicitations, so ISP thinks that the whole 2001:db8:1:2::/64 is here
+------+------+
| |
| | eth2 +-------+
| My router +--------------------------------------+ LAN-2 |
| | radvd announces 2001:db8:1:2::/64 +-------+
| |
+------+------+
| eth1
| radvd announces 2001:db8:1:2::/64
|
|
+---+---+
| LAN-1 |
+-------+
A packet already reached Router due to the same setup of eth0 as before, now it tries to reach an address 2001:db8:1:2::33. But which of two LANs contain this address? They both use the same prefix! Having route 2001:db8:1:2::/64 on both eth1 and eth2 won't work, as such routes will collide, and kernel will send packets to only one of interfaces.
This is where ndprbrd comes to rescue. It has 2 modes, using TAP interface (the recommended mode), and not using it.
| eth0
+-----+-----+
+-------+ eth1 | | eth2 +-------+
| LAN-1 +--------+ My router +--------+ LAN-2 |
+-------+ ^ | | ^ +-------+
| +-----+-----+ |
| | ndprbrd0 |
| | route to 2001:db8:1:2::/64
| | accepts NDP solicitations only, and sends them to both LANs
| | |
+--------+-----------+
When Router tries to send a packet, it sends neighbor solicitation to ndprbrd0, and ndprbrd resends it to all interfaces which it's configured to use. Let's say LAN-1 replies with neighbor advertisement. Then ndprbrd sees it, and adds a static route to the advertised address 2001:db8:1:2::33 to interface eth1. From this point all packets to that address will go directly to eth1, and not to eth2, and not even to ndprbrd0.
If at some point later advertisements about 2001:db8:1:2::33 stopped coming from eth1, the static route is removed after a timeout (10 minutes by default). Then, if a new packet comes to that address, all LANs will be used to discover it again.
Only absence of traffic will trigger such timeout, because with traffic the neighbor solicitations are still sent from time to time. The solicitation will go directly to eth1 because of the static route, the machine will reply, and ndprbrd will see it and reset the timer.
| eth0
route to 2001:db8:1:2:33/128 |
route to 2001:db8:1:2:77/128 +-----+-----+ route to 2001:db8:1:2::55/128
+-------+ eth1 | | eth2 +-------+
| LAN-1 +------------+ My router +------------+ LAN-2 |
+-------+ ^ | | ^ +-------+
| +-----+-----+ |
| | ndprbrd0 |
| | route to 2001:db8:1:2::/64
| | accepts NDP solicitations only, and sends them to both LANs
| | |
+--------+------------+
There is one more missing step: what happens when a machine in LAN-1 tries to send something to LAN-2? The answer is ndppd again: instead of listening only on eth0 ndppd should listen also on eth1 and eth2.
Note about firewall setup: forwarding from eth0 to ndprbrd0 should be accepted.
Otherwise, kernel won't generate NDP solicitations to ndprbrd0. (TODO: this
statement is true for static configuration of ndppd on eth0. Probably auto
doesn't require this, but I didn't check)
If Linux is compiled without TUN/TAP interface support, another mode is available. In this mode, ndprbrd every second switches the route to 2001:db8:1:2::/64 from one interface to another. So when the neighbor solicitation is sent, there is a chance that it's sent to the correct LAN, in which case ndprbrd will see the neighbor advertisement, and add the route for that address.
Note that when an address is discovered in some LAN, due to the timeout mechanism described above, that address will continue working until it disappears from that LAN for 10 minutes. However, several first packets are likely to be dropped. In TAP mode they are still likely to be dropped, but number of first packets dropped is smaller in TAP mode.
./ndprbrd --interface=eth1 --interface=eth2 --prefix=2001:db8:1:2::/64
To change name of TAP interface, use --tun=foo. To use the mode without TAP
interface, use --pendulum.
Sample config of ndppd:
proxy eth0 {
rule 2001:db8:1:2::/64 {
auto
}
}
proxy eth1 {
rule 2001:db8:1:2::/64 {
auto
}
}
proxy eth2 {
rule 2001:db8:1:2::/64 {
auto
}
}
Note that eth0 (interface connected to ISP) is in ndppd, but not in ndprbrd.
Also note that routers don't usually accept RA themselves, so you might need to
specify the default route yourself (or try to set accept_ra to 2).
- Linux
- Compiler with C++11 support:
- GCC 4.9+
- Clang 3.5 with libstdc++ 4.9
- Earlier Clang and Clang with libc++ are not tested
- Switch ISP to one that gives more than /64 :-)
- Give different parts of /64 to LAN-1 and LAN-2, but that breaks SLAAC, so
- Configure a static address for every host,
- Or use DHCPv6
- Bridge all networks together, which means that IPv4 will also be in a single subnet