We read every piece of feedback, and take your input very seriously.
To see all available qualifiers, see our documentation.
Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.
By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.
Already on GitHub? Sign in to your account
I've tested on a Arduino-ProMini with CH340 with your code and SpenceKonde's fork - same problem:
Command-line: /home/stefan/.arduino15/packages/DxCore/tools/avrdude/6.3.0-arduino17or18/bin/avrdude -C/home/stefan/.arduino15/packages/DxCore/hardware/megaavr/1.5.3/avrdude.conf -v -pavr32dd14 -cjtag2updi -P/dev/ttyUSB0 -Ufuse5:w:0b11011001:m -Ufuse6:w:0b00001100:m -Ufuse7:w:0x00:m -Ufuse8:w:0x00:m -Uflash:w:/tmp/arduino_build_610810/Blink.ino.hex:i
/home/stefan/.arduino15/packages/DxCore/tools/avrdude/6.3.0-arduino17or18/bin/avrdude -C/home/stefan/.arduino15/packages/DxCore/hardware/megaavr/1.5.3/avrdude.conf -v -pavr32dd14 -cjtag2updi -P/dev/ttyUSB0 -Ufuse5:w:0b11011001:m -Ufuse6:w:0b00001100:m -Ufuse7:w:0x00:m -Ufuse8:w:0x00:m -Uflash:w:/tmp/arduino_build_610810/Blink.ino.hex:i
1st - programming / writing is OK: (only last line)
Writing | ################################################## | 100% 0.25s avrdude: 790 bytes of flash written
2nd when the verify begins:
avrdude: verifying flash memory against /tmp/arduino_build_610810/Blink.ino.hex: avrdude: load data flash data from input file /tmp/arduino_build_610810/Blink.ino.hex: avrdude: input file /tmp/arduino_build_610810/Blink.ino.hex contains 790 bytes avrdude: reading on-chip flash data:
Reading | avrdude: jtagmkII_paged_load(): timeout/error communicating with programmer (status -1) avrdude: jtagmkII_paged_load(): bad response to read memory command: RSP_NO_TARGET_POWER #########################avrdude: jtagmkII_recv(): msglen 167772161 exceeds max message size 100000, ignoring message avrdude: jtagmkII_recv(): msglen 167772161 exceeds max message size 100000, ignoring message avrdude: jtagmkII_recv(): msglen 167772161 exceeds max message size 100000, ignoring message avrdude: jtagmkII_recv(): msglen 167772161 exceeds max message size 100000, ignoring message
avrdude: jtagmkII_read_byte(): timeout/error communicating with programmer (status -1) avrdude: jtagmkII_read_byte(): timeout/error communicating with programmer (status -1) avrdude: jtagmkII_read_byte(): timeout/error communicating with programmer (status -1) avrdude: jtagmkII_read_byte(): timeout/error communicating with programmer (status -1) avrdude: jtagmkII_read_byte(): fatal timeout/error communicating with programmer (status -1) avr_read(): error reading address 0x0000 read operation not supported for memory "flash" avrdude: failed to read all of flash memory, rc=-2 avrdude: jtagmkII_program_disable(): timeout/error communicating with programmer (status -1) avrdude: jtagmkII_close(): timeout/error communicating with programmer (status -1) avrdude: jtagmkII_close(): timeout/error communicating with programmer (status -1) avrdude done. Thank you.
After that the DUT stops working and the ProMini has to power-cycle and all work again. Verify without programming, after that, also works. Any ideas?
The text was updated successfully, but these errors were encountered:
No branches or pull requests
I've tested on a Arduino-ProMini with CH340 with your code and SpenceKonde's fork - same problem:
Command-line:
/home/stefan/.arduino15/packages/DxCore/tools/avrdude/6.3.0-arduino17or18/bin/avrdude -C/home/stefan/.arduino15/packages/DxCore/hardware/megaavr/1.5.3/avrdude.conf -v -pavr32dd14 -cjtag2updi -P/dev/ttyUSB0 -Ufuse5:w:0b11011001:m -Ufuse6:w:0b00001100:m -Ufuse7:w:0x00:m -Ufuse8:w:0x00:m -Uflash:w:/tmp/arduino_build_610810/Blink.ino.hex:i
1st - programming / writing is OK: (only last line)
2nd when the verify begins:
Reading | avrdude: jtagmkII_paged_load(): timeout/error communicating with programmer (status -1)
avrdude: jtagmkII_paged_load(): bad response to read memory command: RSP_NO_TARGET_POWER
#########################avrdude: jtagmkII_recv(): msglen 167772161 exceeds max message size 100000, ignoring message
avrdude: jtagmkII_recv(): msglen 167772161 exceeds max message size 100000, ignoring message
avrdude: jtagmkII_recv(): msglen 167772161 exceeds max message size 100000, ignoring message
avrdude: jtagmkII_recv(): msglen 167772161 exceeds max message size 100000, ignoring message
After that the DUT stops working and the ProMini has to power-cycle and all work again.
Verify without programming, after that, also works. Any ideas?
The text was updated successfully, but these errors were encountered: