forked from juj/fbcp-ili9341
-
Notifications
You must be signed in to change notification settings - Fork 0
/
mpi3501.cpp
135 lines (107 loc) · 4.31 KB
/
mpi3501.cpp
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
#include "config.h"
#ifdef MPI3501
#include "spi.h"
#include <memory.h>
#include <stdio.h>
void ChipSelectHigh()
{
WAIT_SPI_FINISHED();
CLEAR_GPIO(GPIO_SPI0_CE0); // Enable Touch
SET_GPIO(GPIO_SPI0_CE0); // Disable Touch
__sync_synchronize();
SET_GPIO(GPIO_SPI0_CE1); // Disable Display
CLEAR_GPIO(GPIO_SPI0_CE1); // Enable Display
__sync_synchronize();
}
void InitKeDeiV63()
{
// If a Reset pin is defined, toggle it briefly high->low->high to enable the device. Some devices do not have a reset pin, in which case compile with GPIO_TFT_RESET_PIN left undefined.
#if defined(GPIO_TFT_RESET_PIN) && GPIO_TFT_RESET_PIN >= 0
printf("Resetting display at reset GPIO pin %d\n", GPIO_TFT_RESET_PIN);
SET_GPIO_MODE(GPIO_TFT_RESET_PIN, 1);
SET_GPIO(GPIO_TFT_RESET_PIN);
usleep(120 * 1000);
CLEAR_GPIO(GPIO_TFT_RESET_PIN);
usleep(120 * 1000);
SET_GPIO(GPIO_TFT_RESET_PIN);
usleep(120 * 1000);
#endif
// For sanity, start with both Chip selects high to ensure that the display will see a high->low enable transition when we start.
SET_GPIO(GPIO_SPI0_CE0); // Disable Touch
SET_GPIO(GPIO_SPI0_CE1); // Disable Display
usleep(1000);
// Do the initialization with a very low SPI bus speed, so that it will succeed even if the bus speed chosen by the user is too high.
spi->clk = 34;
__sync_synchronize();
BEGIN_SPI_COMMUNICATION();
{
CLEAR_GPIO(GPIO_SPI0_CE0); // Enable Touch
CLEAR_GPIO(GPIO_SPI0_CE1); // Enable Display
BEGIN_SPI_COMMUNICATION();
usleep(25*1000);
SET_GPIO(GPIO_SPI0_CE0); // Disable Touch
usleep(25*1000);
SPI_TRANSFER(0x00000000); // This command seems to be Reset
usleep(120*1000);
SPI_TRANSFER(0x00000100);
usleep(50*1000);
SPI_TRANSFER(0x00001100);
usleep(60*1000);
SPI_TRANSFER(0xB9001100, 0x00, 0xFF, 0x00, 0x83, 0x00, 0x57);
usleep(5*1000);
SPI_TRANSFER(0xB6001100, 0x00, 0x2C);
SPI_TRANSFER(0x11001100/*Sleep Out*/);
usleep(150*1000);
SPI_TRANSFER(0x3A001100/*Interface Pixel Format*/, 0x00, 0x55);
SPI_TRANSFER(0xB0001100, 0x00, 0x68);
SPI_TRANSFER(0xCC001100, 0x00, 0x09);
SPI_TRANSFER(0xB3001100, 0x00, 0x43, 0x00, 0x00, 0x00, 0x06, 0x00, 0x06);
SPI_TRANSFER(0xB1001100, 0x00, 0x00, 0x00, 0x15, 0x00, 0x1C, 0x00, 0x1C, 0x00, 0x83, 0x00, 0x44);
SPI_TRANSFER(0xC0001100, 0x00, 0x24, 0x00, 0x24, 0x00, 0x01, 0x00, 0x3C, 0x00, 0x1E, 0x00, 0x08);
SPI_TRANSFER(0xB4001100, 0x00, 0x02, 0x00, 0x40, 0x00, 0x00, 0x00, 0x2A, 0x00, 0x2A, 0x00, 0x0D, 0x00, 0x4F);
SPI_TRANSFER(0xE0001100, 0x00, 0x02, 0x00, 0x08, 0x00, 0x11, 0x00, 0x23, 0x00, 0x2C, 0x00, 0x40, 0x00, 0x4A, 0x00, 0x52, 0x00, 0x48, 0x00, 0x41, 0x00, 0x3C, 0x00, 0x33, 0x00, 0x2E, 0x00, 0x28, 0x00, 0x27, 0x00, 0x1B, 0x00, 0x02, 0x00, 0x08, 0x00, 0x11, 0x00, 0x23, 0x00, 0x2C, 0x00, 0x40, 0x00, 0x4A, 0x00, 0x52, 0x00, 0x48, 0x00, 0x41, 0x00, 0x3C, 0x00, 0x33, 0x00, 0x2E, 0x00, 0x28, 0x00, 0x27, 0x00, 0x1B, 0x00, 0x00, 0x00, 0x01);
#define MADCTL_BGR_PIXEL_ORDER (1<<3)
#define MADCTL_ROW_COLUMN_EXCHANGE (1<<5)
#define MADCTL_COLUMN_ADDRESS_ORDER_SWAP (1<<6)
#define MADCTL_ROW_ADDRESS_ORDER_SWAP (1<<7)
#define MADCTL_ROTATE_180_DEGREES (MADCTL_COLUMN_ADDRESS_ORDER_SWAP | MADCTL_ROW_ADDRESS_ORDER_SWAP)
uint8_t madctl = 0;
#ifndef DISPLAY_SWAP_BGR
madctl |= MADCTL_BGR_PIXEL_ORDER;
#endif
#if defined(DISPLAY_FLIP_ORIENTATION_IN_HARDWARE)
madctl |= MADCTL_ROW_COLUMN_EXCHANGE;
#endif
#ifdef DISPLAY_ROTATE_180_DEGREES
madctl ^= MADCTL_ROTATE_180_DEGREES;
#endif
SPI_TRANSFER(0x36001100/*MADCTL: Memory Access Control*/, 0x00, madctl);
SPI_TRANSFER(0x29001100/*Display ON*/);
usleep(200*1000);
ClearScreen();
}
#ifndef USE_DMA_TRANSFERS // For DMA transfers, keep SPI CS & TA active.
END_SPI_COMMUNICATION();
#endif
// And speed up to the desired operation speed finally after init is done.
usleep(10 * 1000); // Delay a bit before restoring CLK, or otherwise this has been observed to cause the display not init if done back to back after the clear operation above.
spi->clk = SPI_BUS_CLOCK_DIVISOR;
}
void TurnBacklightOff()
{
}
void TurnBacklightOn()
{
}
void TurnDisplayOff()
{
}
void TurnDisplayOn()
{
}
void DeinitSPIDisplay()
{
ClearScreen();
TurnDisplayOff();
}
#endif