Skip to content

Latest commit

 

History

History
139 lines (116 loc) · 11 KB

readme.md

File metadata and controls

139 lines (116 loc) · 11 KB
Raw
grand_parent parent title nav_order
32-bit MCU Reference Applications
SAM E54 Xplained Pro Evaluation Kit
Low Power
3

Low Power Application on SAM E54 Xplained Pro Evaluation Kit

Download

Description

The application demonstrates, on power-up, the device is set to Standby Sleep mode. The device wakes up from Standby mode and enters Active mode when you cover the light sensor (by placing a hand over it, for example) on the I/O1 Xplained Pro extension kit. The application periodically prints room temperature on a serial terminal while the light sensor is covered. The device goes back to Standby mode when you uncover the light sensor. LED0 in the SAM E54 evaluation kit is toggled every time the temperature is displayed on the serial console. When you press the switch button SW0, the application switches Sleep mode from Standby mode to Idle mode.

Modules/Technology Used:

  • Peripheral Modules
    • I2C
    • RTC
    • USART
    • DMAC
    • ADC1
    • PM
    • SUPC
    • EIC
    • EVSYS

Hardware Used:

Software/Tools Used:

This project has been verified to work with the following versions of software tools:

Refer Project Manifest present in harmony-manifest-success.yml under the project folder firmware/src/config/sam_e54_xpro

Because Microchip regularly update tools, occasionally issue(s) could be discovered while using the newer versions of the tools. If the project doesn’t seem to work and version incompatibility is suspected, It is recommended to double-check and use the same versions that the project was tested with. To download original version of MPLAB Harmony v3 packages, refer to document How to Use the MPLAB Harmony v3 Project Manifest Feature

Setup:

  • Connect the I/O1 Xplained Pro extension kit to the Extension Header 1 (EXT1) of the SAM E54 Xplained Pro evaluation kit

  • Connect a USB cable to the DEBUG USB port for programming

Programming hex file:

The pre-built hex file can be programmed by following the below steps

Steps to program the hex file

  • Open MPLAB X IDE
  • Close all existing projects in IDE, if any project is opened
  • Go to File -> Import -> Hex/ELF File
  • In the "Import Image File" window, Step 1 - Create Prebuilt Project, click the "Browse" button to select the prebuilt hex file.
  • Select Device has "ATSAME54P20A"
  • Ensure the proper tool is selected under "Hardware Tool"
  • Click on "Next" button
  • In the "Import Image File" window, Step 2 - Select Project Name and Folder, select appropriate project name and folder
  • Click on "Finish" button
  • In MPLAB X IDE, click on "Make and Program Device" Button. The device gets programmed in sometime.
  • Follow the steps in "Running the Demo" section below

Programming/Debugging Application Project:

  • Open the project (same54_low_power\firmware\sam_e54_xpro.X) in MPLAB X IDE.
  • Ensure "SAM E54 Xplained Pro" is selected as hardware tool to program/debug the application
  • Build the code and program the device by clicking on the "Make and Program Device" button in MPLAB X IDE tool bar
  • Follow the steps in "Running the Demo" section below.

Running the Demo:

  • Open Tera Term, connect to serial console. If there is any connection issue on tera terminal, unplug the USB cable connected to Micro-B port, and reconnect it back.

  • Change the baud rate to 115200

  • Perform reset by pressing the "RESET" switch

  • Verify the application title message is displayed

  • Cover the light sensor on the I/O Xplained Pro board by placing your hand over it (or another element to put the light sensor in a dark environment) to print the temperature and message on the terminal. You should see the following messages (containing the temperature value in °F) on the terminal every 500 milliseconds for the duration the light sensor is covered

  • Observe Current Consumption on Data Visualizer
    Note: The Data Visualizer is a program to process and visualize data. The Data Visualizer can receive data from various sources such as the Embedded Debugger Data Gateway Interface (EDBG DGI) and COM ports. It is possible to track an application in run-time using a terminal graph or oscilloscope. It analyzes the power consumption of an application through correlation of code execution and power consumption when used together with a supported probe or board.

  • Open the Data Visualizer application from your PC and select the connected SAM E54 Xplained Pro B board on the DGI Control Panel, then click on Connect. The Data Visualizer will then start searching for protocols from the SAM E54 Xplained Pro board through the EDBG

  • Once the Data Visualizer is connected to the SAM E54 EDBG, different interfaces will appear. Select the Power interface and click on the Start button to start measuring the power consumption of the device

  • Ensure that the jumpers for Current Measurement on the SAM E54 Xplained Pro are set to MEASURE for the MCU and BYPASS for the I/Os

  • The Power Analysis window will appear on the Data Visualizer tool interface

  • The step image shows the device in Standby mode with its measured power consumption. You can observe small peaks that illustrate the 500 milliseconds Real-Time Clock (RTC) timer expiry

    Note: The average value is considered when measuring the power consumption of the device because the instant value is not stable. Then, the power consumption of the device in Standby mode is 225.0 µA.

  • Cover the light sensor on the I/O Xplained Pro board by placing your hand over it (or another element) to print the temperature on the terminal and observe the power consumption of the device

  • Press the SW0 button to switch from Standby mode to Idle mode. The following image shows the transition of the power consumption from Standby mode to Idle mode

  • The following image shows the device in Idle mode with a measured power consumption of 1869.5 µA

    Note: You can observe that the small peaks coming from RTC timer expiry disappeared because the power consumption in Idle mode is higher than the power required to start ADC conversion.

  • Place your hand over the light sensor. The device will wake up on the next ADC window monitor interrupt, read and print data on serial and then re-enter Standby mode. The following image shows the transition of the power consumption by switching from Idle mode to Standby mode

    Note that the above results highlight the power consumption is lower in Standby mode than in Idle mode.

Comments:

Revision:

  • v1.6.0 - Regenerated and Tested the application.
  • v1.5.0 - Removed MHC support, regenerated and tested application.
  • v1.4.0 - Added MCC support, regenerated and tested application.
  • v1.3.0 - Regenerated and tested application.
  • v1.2.0 - Regenerated and tested application.
  • v1.1.0 - Released demo application