compass5

---

Compass 5 Click

Compass 5 Click demo application is developed using the NECTO Studio, ensuring compatibility with mikroSDK's open-source libraries and tools. Designed for plug-and-play implementation and testing, the demo is fully compatible with all development, starter, and mikromedia boards featuring a mikroBUS™ socket.

---

Click Library

• Author : Jelena Milosavljevic
• Date : Jul 2021.
• Type : I2C type

Software Support

Example Description

This is an example that demonstrates the use of Compass 5 Click board that reads data from magnetic sensors for X, Y, and Z axes,processes it and displays it via the UART terminal.

Example Libraries

• MikroSDK.Board
• MikroSDK.Log
• Click.Compass5

Example Key Functions

• compass5_cfg_setup Config Object Initialization function.

void compass5_cfg_setup ( compass5_cfg_t *cfg );

• compass5_init Initialization function.

err_t compass5_init ( compass5_t *ctx, compass5_cfg_t *cfg );

• compass5_write_byte This function writes a desired number of data bytes starting from the selected register by using I2C serial interface.

void compass5_write_byte ( compass5_t *ctx, uint8_t reg, uint8_t tx_data );

• compass5_read_byte This function read 1 byte.

uint8_t compass5_read_byte ( compass5_t *ctx, uint8_t reg );

• compass5_sw_reset This function for software reset.

void compass5_sw_reset ( compass5_t *ctx );

Application Init

Initializes I2C and starts to write log, performs power down mode, sets continuous measurement mode; also write log.

void application_init ( void ) 
{
    log_cfg_t log_cfg;                /**< Logger config object. */
    compass5_cfg_t compass5_cfg;      /**< Click config object. */

    /** 
     * Logger initialization.
     * Default baud rate: 115200
     * Default log level: LOG_LEVEL_DEBUG
     * @note If USB_UART_RX and USB_UART_TX 
     * are defined as HAL_PIN_NC, you will 
     * need to define them manually for log to work. 
     * See @b LOG_MAP_USB_UART macro definition for detailed explanation.
     */
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    log_info( &logger, " Application Init " );
    Delay_ms ( 100 );
    
    // Click initialization.
    compass5_cfg_setup( &compass5_cfg );
    COMPASS5_MAP_MIKROBUS( compass5_cfg, MIKROBUS_1 );
    err_t init_flag = compass5_init( &compass5, &compass5_cfg );
    if ( I2C_MASTER_ERROR == init_flag ) {
        log_error( &logger, " Application Init Error. " );
        log_info( &logger, " Please, run program again... " );

        for ( ; ; );
    }
    compass5_sw_reset( &compass5 );
    Delay_ms ( 500 );
    
    compass5_get_id( &compass5, &company_id, &device_id );
    
    if  ( ( company_id == COMPASS5_COMPANI_ID_NUM ) && ( device_id == COMPASS5_DEVICE_ID_NUM ) ) {
        log_printf( &logger, "--------------------\r\n" );
        log_printf( &logger, "  Compass 3 Click   \r\n" );
        log_printf( &logger, "--------------------\r\n" );
    }
    else {
        log_printf( &logger, "   Fatal error!!!   \r\n" );
        for ( ; ; );
    }
    Delay_ms ( 100 );
    
    log_printf( &logger, "  Power Down Mode  \r\n" );
    log_printf( &logger, "-------------------\r\n" );
    compass5_set_operation_mode( &compass5, COMPASS5_MODE_POWER_DOWN );
    Delay_ms ( 100 );

    log_printf( &logger, "    Continuous     \r\n" );
    log_printf( &logger, " Measurement Mode  \r\n" );
    log_printf( &logger, "-------------------\r\n" );
    compass5_set_operation_mode( &compass5, COMPASS5_MODE_CON_MEASUREMENT_100HZ );
    Delay_ms ( 100 );

    log_printf( &logger, " Start Measurement \r\n" );
    log_printf( &logger, "-------------------\r\n" );
    Delay_ms ( 100 );
    log_info( &logger, " Application Task " );
}

Application Task

When Compass 5 Click is connected to a mikroBUS, this example collects data on the current position of the X, Y and Z axes via I2C communication, processes and displays the data via the UART terminal. All axis data is printed every 2 seconds.

void application_task ( void ) 
{
    int16_t x_val;
    int16_t y_val;
    int16_t z_val;
    
    if ( compass5_check_data_ready( &compass5 ) == COMPASS5_DATA_READY ) {
        compass5_measurement_axis( &compass5, &x_val, &y_val, &z_val );
        Delay_ms ( 10 );
    
        log_printf( &logger, " X-axis: %d mG\r\n", x_val );
        log_printf( &logger, " Y-axis: %d mG\r\n", y_val );
        log_printf( &logger, " Z-axis: %d mG\r\n", z_val );        
        log_printf( &logger,  "--------------------\r\n" );
    }
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
}

Application Output

This Click board can be interfaced and monitored in two ways:

• Application Output - Use the "Application Output" window in Debug mode for real-time data monitoring. Set it up properly by following this tutorial.
• UART Terminal - Monitor data via the UART Terminal using a USB to UART converter. For detailed instructions, check out this tutorial.

Additional Notes and Information

The complete application code and a ready-to-use project are available through the NECTO Studio Package Manager for direct installation in the NECTO Studio. The application code can also be found on the MIKROE GitHub account.

---