eeg

---

EEG Click

EEG Click demo application is developed using the NECTO Studio, ensuring compatibility with mikroSDK's open-source libraries and tools. Designed for plug-and-play implementation and testing, the demo is fully compatible with all development, starter, and mikromedia boards featuring a mikroBUS™ socket.

---

Click Library

• Author : Jelena Milosavljevic
• Date : Aug 2021.
• Type : ADC type

Software Support

Example Description

This example demonstrates the use of EEG Click board.

Example Libraries

• MikroSDK.Board
• MikroSDK.Log
• Click.EEG

Example Key Functions

• eeg_cfg_setup Config Object Initialization function.

void eeg_cfg_setup ( eeg_cfg_t *cfg );

• eeg_init Initialization function.

err_t eeg_init ( eeg_t *ctx, eeg_cfg_t *cfg );

• eeg_read_an_pin_value This function reads results of AD conversion of the AN pin.

err_t eeg_read_an_pin_value ( eeg_t *ctx, uint16_t *data_out );

• eeg_read_an_pin_voltage This function reads results of AD conversion of the AN pin and converts them to proportional voltage level.

err_t eeg_read_an_pin_voltage ( eeg_t *ctx, float *data_out );

Application Init

Initializes Click board.

void application_init ( void )
{
    log_cfg_t log_cfg;  /**< Logger config object. */
    eeg_cfg_t eeg_cfg;  /**< Click config object. */

    /** 
     * Logger initialization.
     * Default baud rate: 115200
     * Default log level: LOG_LEVEL_DEBUG
     * @note If USB_UART_RX and USB_UART_TX 
     * are defined as HAL_PIN_NC, you will 
     * need to define them manually for log to work. 
     * See @b LOG_MAP_USB_UART macro definition for detailed explanation.
     */
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    log_info( &logger, " Application Init " );
    log_printf( &logger, " ----------------------------------------------\r\n" );
    log_printf( &logger, "                ***EEG Click***               \r\n" );
    log_printf( &logger, "----------------------------------------------\r\n" );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    
    // Click initialization.
    eeg_cfg_setup( &eeg_cfg );
    EEG_MAP_MIKROBUS( eeg_cfg, MIKROBUS_1 );
    if ( ADC_ERROR == eeg_init( &eeg, &eeg_cfg ) ){
        log_error( &logger, " Application Init Error. " );
        log_info( &logger, " Please, run program again... " );

        for ( ; ; );
    }
    log_info( &logger, " Application Task " );
}

Application Task

Reads ADC value and sends results on serial plotter every 5 ms.

void application_task ( void ) 
{
    uint16_t eeg_an_value = 0;
        
    if ( eeg_read_an_pin_value( &eeg, &eeg_an_value ) != ADC_ERROR ) {
        log_printf( &logger, " %u,%lu\r\n", eeg_an_value, time );
        Delay_ms ( 5 );
        time += 5;
    }
}

Application Output

This Click board can be interfaced and monitored in two ways:

• Application Output - Use the "Application Output" window in Debug mode for real-time data monitoring. Set it up properly by following this tutorial.
• UART Terminal - Monitor data via the UART Terminal using a USB to UART converter. For detailed instructions, check out this tutorial.

Additional Notes and Information

The complete application code and a ready-to-use project are available through the NECTO Studio Package Manager for direct installation in the NECTO Studio. The application code can also be found on the MIKROE GitHub account.

---