Error: unable to find CMSIS-DAP device

[ISatByTheO]

Hi,

I have been able to compile, upload, and debug simple programs such as the Blink example. But when I attempt to do the same for the WiFiNINA WPA example, I receive the following error:

I'm new to this, so I am unsure if the following information helps or not:
arduino_zero.cfg:

#
#  Arduino Zero OpenOCD script.
#
#  Copyright (c) 2014-2015 Arduino LLC.  All right reserved.
#
#  This library is free software; you can redistribute it and/or
#  modify it under the terms of the GNU Lesser General Public
#  License as published by the Free Software Foundation; either
#  version 2.1 of the License, or (at your option) any later version.
#
#  This library is distributed in the hope that it will be useful,
#  but WITHOUT ANY WARRANTY; without even the implied warranty of
#  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
#  See the GNU Lesser General Public License for more details.
#
#  You should have received a copy of the GNU Lesser General Public
#  License along with this library; if not, write to the Free Software
#  Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
#

source [find interface/cmsis-dap.cfg]

# chip name
set CHIPNAME at91samd21g18
set ENDIAN little

# choose a port here
set telnet_port 0

source [find target/at91samdXX.cfg]

Wifi WPA script:

#include <WiFiNINA.h>

//please enter your sensitive data in the Secret tab
char ssid[] = "{this has a real value}";                // your network SSID (name)
char pass[] = "{this has a real value}";                // your network password (use for WPA, or use as key for WEP)
int status = WL_IDLE_STATUS;             // the Wi-Fi radio's status
int ledState = LOW;                       //ledState used to set the LED
unsigned long previousMillisInfo = 0;     //will store last time Wi-Fi information was updated
unsigned long previousMillisLED = 0;      // will store the last time LED was updated
const int intervalInfo = 5000;            // interval at which to update the board information

void setup() {
  //Initialize serial and wait for port to open:
  Serial.begin(9600);
  while (!Serial);

  // set the LED as output
  pinMode(LED_BUILTIN, OUTPUT);

  // attempt to connect to Wi-Fi network:
  while (status != WL_CONNECTED) {
    Serial.print("Attempting to connect to network: ");
    Serial.println(ssid);
    // Connect to WPA/WPA2 network:
    status = WiFi.begin(ssid, pass);

    // wait 10 seconds for connection:
    delay(10000);
  }

  // you're connected now, so print out the data:
  Serial.println("You're connected to the network");
  Serial.println("---------------------------------------");
}

void loop() {
  unsigned long currentMillisInfo = millis();

  // check if the time after the last update is bigger the interval
  if (currentMillisInfo - previousMillisInfo >= intervalInfo) {
    previousMillisInfo = currentMillisInfo;

    Serial.println("Board Information:");
    // print your board's IP address:
    IPAddress ip = WiFi.localIP();
    Serial.print("IP Address: ");
    Serial.println(ip);

    // print your network's SSID:
    Serial.println();
    Serial.println("Network Information:");
    Serial.print("SSID: ");
    Serial.println(WiFi.SSID());

    // print the received signal strength:
    long rssi = WiFi.RSSI();
    Serial.print("signal strength (RSSI):");
    Serial.println(rssi);
    Serial.println("---------------------------------------");
  }
  
  unsigned long currentMillisLED = millis();
  
  // measure the signal strength and convert it into a time interval
  int intervalLED = WiFi.RSSI() * -10;
 
  // check if the time after the last blink is bigger the interval 
  if (currentMillisLED - previousMillisLED >= intervalLED) {
    previousMillisLED = currentMillisLED;

    // if the LED is off turn it on and vice-versa:
    if (ledState == LOW) {
      ledState = HIGH;
    } else {
      ledState = LOW;
    }

    // set the LED with the ledState of the variable:
    digitalWrite(LED_BUILTIN, ledState);
  }
}

I am currently using the Arduino IDE for local development, but have tried this in the web editor as well. My operating system is win11. I have also tried to re-install the arduino samd board package.

TIA for any assistance.