FXOS8700-AutoSleepDemo.spin2

{
----------------------------------------------------------------------------------------------------
    Filename:       FXOS8700-AutoSleepDemo.spin2
    Description:    Demo of the FXOS8700 driver
        * Auto-sleep functionality
    Author:         Jesse Burt
    Started:        Nov 6, 2021
    Updated:        Jul 10, 2024
    Copyright (c) 2024 - See end of file for terms of use.
----------------------------------------------------------------------------------------------------
}

CON

    _clkfreq    = cfg._clkfreq_def
    _xtlfreq    = cfg._xtlfreq

#include "core.con.click.spin2"
' -- User-modifiable constants
    CLICK_BASE  = 16                            ' MikroE Click board base I/O pin (multiple of 16)
    INT1        = 2
'--

OBJ

    cfg:    "boardcfg.p2eval"

    { MikroE Click boards (change CLICK_BASE above) }
    'sensor: "sensor.imu.6dof.fxos8700" | SCL=SCL_PIN, SDA=SDA_PIN, I2C_FREQ=400_000, I2C_ADDR=%11

    { custom I/O settings }
    sensor: "sensor.imu.6dof.fxos8700" | SCL=0, SDA=1, I2C_FREQ=400_000, I2C_ADDR=%11, RST_PIN=-1

    ser:    "com.serial.terminal.ansi" | SER_BAUD=2_000_000


VAR

    long _isr_stack[50]                         ' stack for ISR core
    long _intflag                               ' interrupt flag


PUB main() | intsource, temp, sysmod

    setup()
    sensor.preset_active()                      ' default settings, but enable sensor power,
                                                ' and set scale factors
    sensor.accel_int_polarity(sensor.LOW)
    sensor.accel_data_rate(100)                 ' 100Hz ODR when active
    sensor.auto_sleep_ena(true)                 ' enable auto-sleep
    sensor.accel_sleep_pwr_mode(sensor.LOPWR)   ' lo-power mode when sleeping
    sensor.accel_pwr_mode(sensor.HIGHRES)       ' high-res mode when awake
    sensor.trans_axis_ena(%011)                 ' transient detection on X, Y
    sensor.trans_thresh(0_252000)               ' set thresh to 0.252g (0..8g)
    sensor.trans_set_cnt(1)                     ' reset counter
    sensor.inact_set_time(5_120)                ' inactivity timeout ~5sec
    sensor.inact_int(sensor.WAKE_TRANS)         ' wake on transient accel
    sensor.accel_int_mask(sensor.INT_AUTOSLPWAKE | sensor.INT_TRANS)
    sensor.accel_int_routing(sensor.INT_AUTOSLPWAKE | sensor.INT_TRANS)
    sensor.auto_sleep_data_rate(6)              ' 6Hz ODR when sleeping
    pinl(LED)

    ' The demo continuously displays the current accelerometer data.
    ' When the sensor goes to sleep after approx. 5 seconds, the change
    '   in data rate is visible as a slowed update of the display.
    ' To wake the sensor, shake it along the X and/or Y axes
    '   by at least the amount set in trans_thresh() above.
    ' When the sensor is awake, the LED should be on.
    ' When the sensor goes to sleep, it should turn off.
    repeat
        ser.pos_xy(0, 3)
        show_accel_data()                       ' show accel data
        if ( _intflag )                         ' interrupt triggered
            intsource := sensor.accel_int()
            if ( intsource & sensor.INT_TRANS ) ' transient acceleration event
                temp := sensor.trans_interrupt()' clear the trans. interrupt
            if ( intsource & sensor.INT_AUTOSLPWAKE )
                sysmod := sensor.sys_mode()
                if ( sysmod & sensor.SLEEP )    ' op. mode is sleep,
                    pinl(LED)                   '   so turn LED off
                elseif (sysmod & sensor.ACTIVE) ' else active,
                    pinh(LED)                   '   turn it on

        if ( ser.getchar_noblock() == "c" )     ' press the 'c' key in the demo
            cal_accel()                         ' to calibrate sensor offsets


PRI cog_isr()
' Interrupt service routine
    pinf(INT1)                                  ' INT1 as input
    repeat
        if (pinr(INT1) == 0)                    ' wait for INT1 (active low)
            _intflag := 1                       '   set flag
        elseif (pinr(INT1) == 1)                ' now wait for it to clear
            _intflag := 0                       '   clear flag

PUB setup()

    ser.start()
    waitms(30)
    ser.clear()
    ser.strln(@"Serial terminal started")

    if ( sensor.start() )
        ser.strln(@"FXOS8700 driver started (I2C)")
    else
        ser.strln(@"FXOS8700 driver failed to start - halting")
        repeat

    cogspin(NEWCOG, cog_isr(), @_isr_stack)     ' start ISR in another core

#include "acceldemo.common.spin2h"              ' use code common to all accelerometer demos


DAT
{
Copyright 2024 Jesse Burt

Permission is hereby granted, free of charge, to any person obtaining a copy of this software and
associated documentation files (the "Software"), to deal in the Software without restriction,
including without limitation the rights to use, copy, modify, merge, publish, distribute,
sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is
furnished to do so, subject to the following conditions:

The above copyright notice and this permission notice shall be included in all copies or
substantial portions of the Software.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM,
DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT
OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
}