Skip to content

Latest commit

 

History

History
124 lines (98 loc) · 7.03 KB

14158704L.md

File metadata and controls

124 lines (98 loc) · 7.03 KB
title description addedAt pageClass
Lidl 14158704L control via MQTT
Integrate your Lidl 14158704L via Zigbee2MQTT with whatever smart home infrastructure you are using without the vendor's bridge or gateway.
2022-03-31 11:55:00 -0700
device-page

Lidl 14158704L

Model 14158704L
Vendor Lidl
Description Livarno Home LED floor lamp, RGBW
Exposes light (state, brightness, color_temp, color_xy), effect, do_not_disturb, color_power_on_behavior, linkquality
Picture Lidl 14158704L

Notes

Pairing

Turn the lamp off, then on 3x with 1 second delay between each action.
The delay between on/off actions is critical. Quickly turning the device on/off will not put it in pairing mode. A good rule of thumb is ponouncing "Mississippi" between each on/off action.

  1. Start with the lamp off
  2. Wait for 1 second
  3. On
  4. Wait for 1 second
  5. Off
  6. Wait for 1 second
  7. On
  8. Wait for 1 second
  9. Off
  10. Wait for 1 second
  11. On
  12. Wait for 1 second
  13. The device should now slowly glow brigher and dimmer and is now in pairing mode.

If you do not succeed, try slightly increasing the time between on/off actions, and leave it off for several seconds before attempting again.

Options

How to use device type specific configuration

  • transition: Controls the transition time (in seconds) of on/off, brightness, color temperature (if applicable) and color (if applicable) changes. Defaults to 0 (no transition). The value must be a number with a minimum value of 0

  • color_sync: When enabled colors will be synced, e.g. if the light supports both color x/y and color temperature a conversion from color x/y to color temperature will be done when setting the x/y color (default true). The value must be true or false

  • state_action: State actions will also be published as 'action' when true (default false). The value must be true or false

Exposes

Light

This light supports the following features: state, brightness, color_temp, color_xy.

  • state: To control the state publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"state": "ON"}, {"state": "OFF"} or {"state": "TOGGLE"}. To read the state send a message to zigbee2mqtt/FRIENDLY_NAME/get with payload {"state": ""}.
  • brightness: To control the brightness publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"brightness": VALUE} where VALUE is a number between 0 and 254. To read the brightness send a message to zigbee2mqtt/FRIENDLY_NAME/get with payload {"brightness": ""}.
  • color_temp: To control the color temperature (in reciprocal megakelvin a.k.a. mired scale) publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"color_temp": VALUE} where VALUE is a number between 153 and 500, the higher the warmer the color. To read the color temperature send a message to zigbee2mqtt/FRIENDLY_NAME/get with payload {"color_temp": ""}. Besides the numeric values the following values are accepected: coolest, cool, neutral, warm, warmest.
  • color_xy: To control the XY color (CIE 1931 color space) publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"color": {"x": X_VALUE, "y": Y_VALUE}} (e.g. {"color":{"x":0.123,"y":0.123}}). To read the XY color send a message to zigbee2mqtt/FRIENDLY_NAME/get with payload {"color":{"x":"","y":""}}. Alternatively it is possible to set the XY color via RGB:
    • {"color": {"r": R, "g": G, "b": B}} e.g. {"color":{"r":46,"g":102,"b":150}}
    • {"color": {"rgb": "R,G,B"}} e.g. {"color":{"rgb":"46,102,150"}}
    • {"color": {"hex": HEX}} e.g. {"color":{"hex":"#547CFF"}}

Transition

For all of the above mentioned features it is possible to do a transition of the value over time. To do this add an additional property transition to the payload which is the transition time in seconds. Examples: {"brightness":156,"transition":3}, {"color_temp":241,"transition":1}.

Moving/stepping

Instead of setting a value (e.g. brightness) directly it is also possible to:

  • move: this will automatically move the value over time, to stop send value stop or 0.
  • step: this will increment/decrement the current value by the given one.

The direction of move and step can be either up or down, provide a negative value to move/step down, a positive value to move/step up. To do this send a payload like below to zigbee2mqtt/FRIENDLY_NAME/set

NOTE: brightness move/step will stop at the minimum brightness and won't turn on the light when it's off. In this case use brightness_move_onoff/brightness_step_onoff

{
  "brightness_move": -40, // Starts moving brightness down at 40 units per second
  "brightness_move": 0, // Stop moving brightness
  "brightness_step": 40 // Increases brightness by 40
  "color_temp_move": 60, // Starts moving color temperature up at 60 units per second
  "color_temp_move": "stop", // Stop moving color temperature
  "color_temp_step": 99, // Increase color temperature by 99
}

Effect (enum)

Triggers an effect on the light (e.g. make light blink for a few seconds). Value will not be published in the state. It's not possible to read (/get) this value. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"effect": NEW_VALUE}. The possible values are: blink, breathe, okay, channel_change, finish_effect, stop_effect.

Do_not_disturb (binary)

Do not disturb mode, when enabled this function will keep the light OFF after a power outage. Value can be found in the published state on the do_not_disturb property. It's not possible to read (/get) this value. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"do_not_disturb": NEW_VALUE}. If value equals true do_not_disturb is ON, if false OFF.

Color_power_on_behavior (enum)

Power on behavior state. Value can be found in the published state on the color_power_on_behavior property. It's not possible to read (/get) this value. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"color_power_on_behavior": NEW_VALUE}. The possible values are: initial, previous, cutomized.

Linkquality (numeric)

Link quality (signal strength). Value can be found in the published state on the linkquality property. It's not possible to read (/get) or write (/set) this value. The minimal value is 0 and the maximum value is 255. The unit of this value is lqi.