This is the output of running help on a Playdate with firmware 1.10 after running unlock:
The following commands are available:
Telnet commands:
help Displays all available commands or individual help on each command
loop loop next command x times with delay y ms (eg loop 10 100 help)
lock Lock the firmware command interface
eMMC kvstore:
kvget kvget <key> [len]
kvput kvput <key> <len>
kvrm kvrm <key>
kvwipe kvwipe
CPU Control:
gpio gpio <port> <i(pu/pd)/1(pu/pd)/0(pu/pd)>. (gpio A3 1 or gpio B2 ipu)
i2cread i2cread <unit> <address> <register> <len>. (i2cread 0 0x47 0x38 3)
i2cwrite i2cwrite <unit> <address> <register> <value>. (i2cwrite 3 0x47 0x38 0xff)
tlv493read tlv493read <address> <len>. (tlv493read 0x47 3)
tlv493write tlv493write <address> <val>. (tlv493write 0x47 0x00 0x37 0x48)
serialwrite serialwrite <string>
serialread Print the device serial number
pwwrite pwwrite <string>
pwread pwread
reset reset system
dfu reset system
trace trace_<delay>. (trace 10)
stoptrace stoptrace
bootdisk reboot into recovery segment USB disk
datadisk reboot into data segment USB disk
sysdisk reboot into system segment USB disk
factoryreset factory reset
formatboot format recovery disk
formatdata format data disk
formatsys format system disk
shutdown put device in stop mode
cleartime clear time from device
settime sets the RTC. format is ISO8601 plus weekday (1=mon) e.g.: 2018-03-20T19:58:29Z 2
gettime reads the RTC
rtccalib rtccalib <on/off>: enable rtc calibration output
vbat get battery voltage
batpct get battery percentage
temp get estimated ambient temperature
peek peek <addr>: Read a 32-bit value from memory
poke poke <addr> <value>: Write a 32-bit value int memory
dump dump <start> <end>: Dump memory in range [start-end) as bytes
dumpw dumpw <start> <end>: Dump memory in range [start-end) as words
stop stop cpu
led led <R> <G> <B>. (led 0-255 0-255 0-255)
leddemo leddemo
charge charge <on/off>: enables/disables battery charging
readcharger readcharger
burn waste cpu to run down the battery
lsedrive get LSE drive level
extv get 5V_ext voltage
dcache dcache <on/off>: turn dcache on or off
icache icache <on/off>: turn icache on or off
rcccsr report bootinfo.rcccsr value
rdp rdp <enable/disable>
suspendusb sets USB current limit to 500uA
eMMC Control:
emmctest emmctest
emmcinfo emmcinfo
emmcwipe emmcwipe
emmcdump emmcdump <addr> <len>
Audio Control:
audiotest Send test data to audio output
audiosweep audiosweep <startfreq> <endfreq> <length>: Send sweep signal to audio output. Frequencies are (integer) Hz, length is milliseconds
stopaudio Stop audio output
startaudio Start audio output
audioout audioout <speaker|headphone|both|none|bt|onboard>
mictest mictest <int|ext> <filename> <length>: Record microphone to given file. length is in milliseconds
blowtest blowtest
micbiastest micbiastest <level:0-5> <verbose:0/1>
Encryption:
encrypt encrypt <file_in> <file_out>
decrypt decrypt <file_in> <file_out>
Runtime control:
echo echo (on|off): turn console echo on or off
buttons Test buttons & crank
tunebuttons tunebuttons <debounce> <holdoff>
btn btn <btn>: simulate a button press. +a/-a/a for down/up/both
changecrank changecrank +-<degrees>
dockcrank simulates crank docking
enablecrank Reenables crank updates
disablecrank Disables crank updates
accel simulate accelerometer change
pause Pause execution
resume Resume execution
restart Restart Lua runtime
step Step one frame
fps fps to return current frame rate, fps <frame rate> to set
screen Dump framebuffer data (400x240 bits)
bitmap Send bitmap to screen (followed by 400x240 bits)
lcdtest Draw a marching stripes pattern on the screen
controller start or stop controller mode
eval execute a compiled Lua function
run run <path to pdx>: Run the named program
whatsrunning Returns the path of the currently running program
luatrace Get a Lua stack trace
stats Display runtime stats
autolock autolock <always|onBattery>
version Display build target and SDK version
station station <travel agent station name>: Configure device for running at the named station
setvolume setvolume <amt>:, 0-255
getvolume Returns the volume level 0-255
wifi wifi <GET|POST> <url> [file1] [file2]
wifitest wifitest <network> <password>
memtest memtest
memstats memstats
woprset woprset [server]
woprget woprget
syncperiod syncperiod <initial_s> [period_s]
hibernate hibernate
Filesystem Stuff:
listfiles listfiles path: list files at path
getfile getfile <path>: get file contents at path
putfile putfile <path> <size>: upload file to path
mkdir mkdir <path>
delete delete <path>
rmdir rmdir <path>: Recursively delete directory
unzip unzip zip_path out_path
md5 md5 <file_path>
memio commands:
memiomd5 memiomd5 <addr> <size>
Stream:
stream stream <enable|disable|poke>
ESP functions:
espreset reset the ESP chip
espoff turn off the ESP
espbootlog get the ESP startup log
espfile espfile <path> <address> <md5> <uncompressed size>: add the given file to the upload list. If <uncompressed size> is added then the file is assumed to be compressed.
espflash espflash <baud> [0|1] send the files listed with the espfile command to the ESP flash.
espbaud espbaud <speed> [cts]
esp esp <cmd>: Forward a command to the ESP firmware, read until keypress
esptest esptest <baud> <cts>
espwipe espwipe
espversion espversion
wifiperf wifiperf <addr> <port>
wifistop wifistop
Firmware Update:
fw fw
fwup fwup [bundle_path]
recovery recovery
unstage unstage
unzip test:
unzipmem unzipmem <addr> <len> <path>
Memfault Tests:
hardfault Trigger a hardfault
assert Trigger an assert
mflt mflt <status|clear|send>
- Added
factoryreset - Added
tunebuttons - Added
neveroption forautolock