You signed in with another tab or window. Reload to refresh your session.You signed out in another tab or window. Reload to refresh your session.You switched accounts on another tab or window. Reload to refresh your session.Dismiss alert
Not sure if I've changed something in my code or updated some libraries ...
Yesterday my code was ok.
I combined few examples into one code and I have a problem with numer.setState function:
#include <WiFi.h>
#include <ArduinoHA.h>
#define BROKER_ADDR IPAddress(192,168,1,200)
#define BROKER_USERNAME "xxxx" // replace with your credentials
#define BROKER_PASSWORD "xxxx"
#define WIFI_SSID "xxxx"
#define WIFI_PASSWORD "xxxx"
byte mac[] = {0x00, 0x10, 0xFA, 0x6E, 0x38, 0x4A};
unsigned long lastAvailabilityToggleAt = millis();
WiFiClient client;
HADevice device;
HAMqtt mqtt(client, device);
HANumber number("myNumber");
HALock lock("myLock");
HACover cover("myCover", HACover::PositionFeature);
unsigned long previousMillis = 0; // will store last time LED was updated
const long interval = 1000; // interval at which to blink (milliseconds)
int i=0;
void setup() {
byte mac[6];
WiFi.macAddress(mac);
device.setUniqueId(mac, sizeof(mac));
Serial.begin(115200);
while (!Serial) {
;
}
Serial.println("Serial Started...");
WiFi.begin(WIFI_SSID, WIFI_PASSWORD);
while (WiFi.status() != WL_CONNECTED) {
delay(500);
Serial.print(".");
}
Serial.println("");
Serial.println("WiFi connected");
device.setName("Arduino");
device.setSoftwareVersion("1.0.0");
number.onCommand(onNumberCommand);
number.setIcon("mdi:window-shutter");
number.setName("My number");
lock.onCommand(onLockCommand);
lock.setName("Window Lock"); // optional
lock.setIcon("mdi:lock"); // optional
lastAvailabilityToggleAt = millis();
device.enableSharedAvailability();
device.enableLastWill();
mqtt.begin(BROKER_ADDR, BROKER_USERNAME, BROKER_PASSWORD);
}
void loop() {
mqtt.loop();
unsigned long currentMillis = millis();
if (currentMillis - previousMillis >= interval) {
previousMillis = currentMillis;
Serial.print("Position: ");
Serial.println(i);
number.setState(i);
cover.setPosition(i);
if (i==101){
cover.setState(HACover::StateOpen);
}
if (i==0){
cover.setState(HACover::StateClosed);
}
if ((i>0) && (i<100)){
cover.setState(HACover::StateOpening);
}
i++;
if (i==102){
i=0;
}
}
//if ((millis() - lastAvailabilityToggleAt) > 5000) {
// device.setAvailability(!device.isAvailable());
// lastAvailabilityToggleAt = millis();
// }
}
void onCoverCommand(HACover::CoverCommand cmd, HACover* sender) {
if (cmd == HACover::CommandOpen) {
Serial.println("Command: Open");
sender->setState(HACover::StateOpening); // report state back to the HA
} else if (cmd == HACover::CommandClose) {
Serial.println("Command: Close");
sender->setState(HACover::StateClosing); // report state back to the HA
} else if (cmd == HACover::CommandStop) {
Serial.println("Command: Stop");
sender->setState(HACover::StateStopped); // report state back to the HA
}
// Available states:
// HACover::StateClosed
// HACover::StateClosing
// HACover::StateOpen
// HACover::StateOpening
// HACover::StateStopped
// You can also report position using setPosition() method
}
void onLockCommand(HALock::LockCommand cmd, HALock* sender) {
if (cmd == HALock::CommandLock) {
Serial.println("Command: Lock");
sender->setState(HALock::StateLocked); // report state back to the HA
} else if (cmd == HALock::CommandUnlock) {
Serial.println("Command: Unlock");
sender->setState(HALock::StateUnlocked); // report state back to the HA
} else if (cmd == HALock::CommandOpen) {
if (sender->getCurrentState() != HALock::StateUnlocked) {
return; // optionally you can verify if the lock is unlocked before opening
}
Serial.println("Command: Open");
}
}
void onNumberCommand(HANumeric number, HANumber* sender)
{
if (!number.isSet()) {
// the reset command was send by Home Assistant
} else {
// you can do whatever you want with the number as follows:
int8_t numberInt8 = number.toInt8();
int16_t numberInt16 = number.toInt16();
int32_t numberInt32 = number.toInt32();
uint8_t numberUInt8 = number.toUInt8();
uint16_t numberUInt16 = number.toUInt16();
uint32_t numberUInt32 = number.toUInt32();
float numberFloat = number.toFloat();
}
sender->setState(number); // report the selected option back to the HA panel
//Serial.print("Slider: ");
//Serial.println(number.toInt16());
}
Compilation error: call of overloaded 'setState(int)' is ambiguous
I would really appreaciate any help. THX!
The text was updated successfully, but these errors were encountered:
Hi,
Arduino IDE 2.3.2
aha lib 2.1.0
Not sure if I've changed something in my code or updated some libraries ...
Yesterday my code was ok.
I combined few examples into one code and I have a problem with numer.setState function:
Compilation error: call of overloaded 'setState(int)' is ambiguous
I would really appreaciate any help. THX!
The text was updated successfully, but these errors were encountered: