- 中文版本
- Basic Example:
This example uses the Classic Bluetooth A2DP profile to distribute and receive audio streams and the AVRCP profile to notify and control media information. It also allows the development board to answer incoming calls as a Hands-Free Unit.
The complete pipeline of this example is as follows:
[Bluetooth] ---> bt_stream_reader ---> i2s_stream_writer ---> codec_chip ---> speaker
This example runs on the boards that are marked with a green checkbox in the table. Please remember to select the board in menuconfig as discussed in Section Configuration below.
This example supports IDF release/v5.0 and later branches. By default, it runs on ADF's built-in branch $ADF_PATH/esp-idf.
The default board for this example is ESP32-Lyrat V4.3. If you need to run this example on other development boards, select the board in menuconfig, such as ESP32-Lyrat-Mini V1.1.
menuconfig > Audio HAL > ESP32-Lyrat-Mini V1.1
Build the project and flash it to the board, then run monitor tool to view serial output (replace PORT with your board's serial port name):
idf.py -p PORT flash monitor
To exit the serial monitor, type Ctrl-].
See ESP-IDF Programming Guide for full steps to configure and build an ESP-IDF project.
- After the example starts running, the development board waits to be connected to the mobile phone over Bluetooth. The log is as follows:
entry 0x400806f4
I (27) boot: ESP-IDF v4.2.2-1-g379ca2123 2nd stage bootloader
I (27) boot: compile time 10:44:58
I (27) boot: chip revision: 3
I (31) boot.esp32: SPI Speed : 40MHz
I (36) boot.esp32: SPI Mode : DIO
I (40) boot.esp32: SPI Flash Size : 2MB
I (45) boot: Enabling RNG early entropy source...
I (50) boot: Partition Table:
I (54) boot: ## Label Usage Type ST Offset Length
I (61) boot: 0 nvs WiFi data 01 02 00009000 00006000
I (69) boot: 1 phy_init RF data 01 01 0000f000 00001000
I (76) boot: 2 factory factory app 00 00 00010000 00124f80
I (84) boot: End of partition table
I (88) esp_image: segment 0: paddr=0x00010020 vaddr=0x3f400020 size=0x2ff20 (196384) map
I (172) esp_image: segment 1: paddr=0x0003ff48 vaddr=0x3ffbdb60 size=0x000d0 ( 208) load
I (172) esp_image: segment 2: paddr=0x00040020 vaddr=0x400d0020 size=0xbbc60 (769120) map
0x400d0020: _stext at ??:?
I (471) esp_image: segment 3: paddr=0x000fbc88 vaddr=0x3ffbdc30 size=0x03514 ( 13588) load
I (477) esp_image: segment 4: paddr=0x000ff1a4 vaddr=0x40080000 size=0x1846c ( 99436) load
0x40080000: _WindowOverflow4 at /hengyongchao/esp-idfs/esp-idf-v4.2.2-psram/components/freertos/xtensa/xtensa_vectors.S:1730
I (534) boot: Loaded app from partition at offset 0x10000
I (534) boot: Disabling RNG early entropy source...
I (535) psram: This chip is ESP32-D0WD
I (540) spiram: Found 64MBit SPI RAM device
I (544) spiram: SPI RAM mode: flash 40m sram 40m
I (549) spiram: PSRAM initialized, cache is in low/high (2-core) mode.
I (557) cpu_start: Pro cpu up.
I (560) cpu_start: Application information:
I (565) cpu_start: Project name: a2dp_sink_and_hfp_example
I (572) cpu_start: App version: v2.2-252-gdd93b207-dirty
I (578) cpu_start: Compile time: Nov 26 2021 10:44:52
I (584) cpu_start: ELF file SHA256: e1f292df795c02c7...
I (590) cpu_start: ESP-IDF: v4.2.2-1-g379ca2123
I (596) cpu_start: Starting app cpu, entry point is 0x40081cd4
0x40081cd4: call_start_cpu1 at /hengyongchao/esp-idfs/esp-idf-v4.2.2-psram/components/esp32/cpu_start.c:287
I (0) cpu_start: App cpu up.
I (1490) spiram: SPI SRAM memory test OK
I (1498) heap_init: Initializing. RAM available for dynamic allocation:
I (1498) heap_init: At 3FFAFF10 len 000000F0 (0 KiB): DRAM
I (1500) heap_init: At 3FFB7468 len 00000B98 (2 KiB): DRAM
I (1506) heap_init: At 3FFB9A20 len 00004108 (16 KiB): DRAM
I (1512) heap_init: At 3FFC2838 len 0001D7C8 (117 KiB): DRAM
I (1519) heap_init: At 3FFE0440 len 00003AE0 (14 KiB): D/IRAM
I (1525) heap_init: At 3FFE4350 len 0001BCB0 (111 KiB): D/IRAM
I (1531) heap_init: At 4009846C len 00007B94 (30 KiB): IRAM
I (1538) cpu_start: Pro cpu start user code
I (1543) spiram: Adding pool of 4034K of external SPI memory to heap allocator
I (1565) spi_flash: detected chip: gd
I (1566) spi_flash: flash io: dio
W (1566) spi_flash: Detected size(8192k) larger than the size in the binary image header(2048k). Using the size in the binary image header.
I (1576) cpu_start: Starting scheduler on PRO CPU.
I (0) cpu_start: Starting scheduler on APP CPU.
I (1587) spiram: Reserving pool of 32K of internal memory for DMA/internal allocations
I (1627) BLUETOOTH_EXAMPLE: [ 1 ] Create Bluetooth service
I (1627) BTDM_INIT: BT controller compile version [ba56601]
I (1627) system_api: Base MAC address is not set
I (1637) system_api: read default base MAC address from EFUSE
I (1647) phy_init: phy_version 4660,0162888,Dec 23 2020
W (1647) phy_init: failed to load RF calibration data (0xffffffff), falling back to full calibration
W (2357) BT_BTC: A2DP Enable with AVRC
I (2387) BLUETOOTH_EXAMPLE: [ 2 ] Start codec chip
I (2387) gpio: GPIO[19]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:3
I (2647) gpio: GPIO[21]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0
I (2647) ES8388_DRIVER: init,out:02, in:00
I (2807) AUDIO_HAL: Codec mode is 2, Ctrl:1
I (2897) BLUETOOTH_EXAMPLE: [ 3 ] Create audio pipeline for playback
I (2897) BLUETOOTH_EXAMPLE: [3.1] Create i2s stream to write data to codec chip and read data from codec chip
I (2897) I2S: DMA Malloc info, datalen=blocksize=1200, dma_buf_count=3
I (2907) I2S: DMA Malloc info, datalen=blocksize=1200, dma_buf_count=3
I (2927) I2S: APLL: Req RATE: 44100, real rate: 44099.988, BITS: 16, CLKM: 1, BCK_M: 8, MCLK: 11289597.000, SCLK: 1411199.625000, diva: 1, divb: 0
I (2937) LYRAT_V4_3: I2S0, MCLK output by GPIO0
W (2937) I2S: I2S driver already installed
I (2947) LYRAT_V4_3: I2S0, MCLK output by GPIO0
I (2947) BLUETOOTH_EXAMPLE: [3.2] Create Bluetooth stream
I (2957) BLUETOOTH_EXAMPLE: [3.3] Register all elements to audio pipeline
I (2957) BLUETOOTH_EXAMPLE: [3.4] Link it together [Bluetooth]-->bt_stream_reader-->i2s_stream_writer-->[codec_chip]
I (2977) AUDIO_PIPELINE: link el->rb, el:0x3f80fde0, tag:bt, rb:0x3f80ff74
I (2977) AUDIO_PIPELINE: link el->rb, el:0x3f80fba8, tag:i2s_r, rb:0x3f811fb4
I (2987) BLUETOOTH_EXAMPLE: [ 4 ] Initialize peripherals
E (2997) gpio: gpio_install_isr_service(438): GPIO isr service already installed
I (2997) BLUETOOTH_EXAMPLE: [4.1] Initialize Touch peripheral
I (3007) gpio: GPIO[36]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:3
I (3017) gpio: GPIO[39]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:3
I (3027) BLUETOOTH_EXAMPLE: [4.2] Create Bluetooth peripheral
W (3047) PERIPH_TOUCH: _touch_init
I (3047) BLUETOOTH_EXAMPLE: [4.2] Start all peripherals
I (3047) BLUETOOTH_EXAMPLE: [ 5 ] Set up event listener
I (3057) BLUETOOTH_EXAMPLE: [5.1] Listening event from all elements of pipeline
I (3067) BLUETOOTH_EXAMPLE: [5.2] Listening event from peripherals
I (3067) BLUETOOTH_EXAMPLE: [ 6 ] Start audio_pipeline
I (3077) AUDIO_ELEMENT: [bt-0x3f80fde0] Element task created
I (3087) AUDIO_ELEMENT: [i2s_w-0x3f80fa24] Element task created
I (3087) AUDIO_PIPELINE: Func:audio_pipeline_run, Line:359, MEM Total:4271372 Bytes, Inter:218832 Bytes, Dram:187232 Bytes
I (3107) AUDIO_ELEMENT: [i2s_w] AEL_MSG_CMD_RESUME,state:1
I (3107) I2S_STREAM: AUDIO_STREAM_WRITER
I (3107) AUDIO_PIPELINE: Pipeline started
I (3117) AUDIO_ELEMENT: [i2s_r-0x3f80fba8] Element task created
I (3117) AUDIO_ELEMENT: [raw-0x3f80fcc8] Element task created
I (3127) AUDIO_PIPELINE: Func:audio_pipeline_run, Line:359, MEM Total:4265380 Bytes, Inter:214892 Bytes, Dram:183292 Bytes
I (3137) AUDIO_ELEMENT: [i2s_r] AEL_MSG_CMD_RESUME,state:1
I (3147) I2S_STREAM: AUDIO_STREAM_READER,Rate:44100,ch:2
I (3167) I2S: APLL: Req RATE: 44100, real rate: 44099.988, BITS: 16, CLKM: 1, BCK_M: 8, MCLK: 11289597.000, SCLK: 1411199.625000, diva: 1, divb: 0
I (3177) AUDIO_PIPELINE: Pipeline started
I (3177) BLUETOOTH_EXAMPLE: [ 7 ] Listen for all pipeline events- Start scanning for the Bluetooth device named
ESP_ADF_AUDIOon your mobile phone and connect to it. The log is as follows:
E (14397) BT_APPL: bta_av_rc_create ACP handle exist for shdl:0
W (14427) BT_APPL: new conn_srvc id:27, app_id:1
E (14437) BT_HF: APP HFP event: CONNECTION_STATE_EVT
W (14537) BT_APPL: new conn_srvc id:19, app_id:0
E (14537) BT_HF: --connection state connected, peer feats 0x0, chld_feats 0x0
E (14537) BT_HF: APP HFP event: NETWORK_STATE_EVT
E (14547) BT_HF: --NETWORK STATE available
E (14547) BT_HF: APP HFP event: CALL_IND_EVT
E (14557) BT_HF: --Call indicator NO call in progress
E (14557) BT_HF: APP HFP event: CALL_SETUP_IND_EVT
E (14567) BT_HF: --Call setup indicator NONE
E (14577) BT_HF: APP HFP event: BATTERY_LEVEL_IND_EVT
E (14577) BT_HF: --battery level 5
E (14587) BT_HF: APP HFP event: SIGNAL_STRENGTH_IND_EVT
E (14587) BT_HF: -- signal strength: 4
E (14597) BT_HF: APP HFP event: ROAMING_STATUS_IND_EVT
E (14597) BT_HF: --ROAMING: inactive
E (14607) BT_HF: APP HFP event: CALL_HELD_IND_EVT
E (14607) BT_HF: --Call held indicator NONE held
I (14617) BLUETOOTH_EXAMPLE: [ * ] Receive music info from Bluetooth, sample_rates=44100, bits=16, ch=2
I (14657) AUDIO_ELEMENT: [i2s_w] AEL_MSG_CMD_PAUSE
I (14687) I2S: APLL: Req RATE: 44100, real rate: 44099.988, BITS: 16, CLKM: 1, BCK_M: 8, MCLK: 11289597.000, SCLK: 1411199.625000, diva: 1, divb: 0
I (14687) AUDIO_ELEMENT: [i2s_w] AEL_MSG_CMD_RESUME,state:4
I (14697) I2S_STREAM: AUDIO_STREAM_WRITER
E (14707) BT_HF: APP HFP event: CONNECTION_STATE_EVT
E (14717) BT_HF: --connection state slc_connected, peer feats 0x3ef, chld_feats 0x3f
E (14717) BT_HF: APP HFP event: INBAND_RING_TONE_EVT
E (14717) BT_HF: --inband ring state Provided
I (29317) BT_LOG: bta_av_link_role_ok hndl:x41 role:1 conn_audio:x1 bits:1 features:x824b- After a successful connection, please open the player on your phone and tap the play button. Then, the development board will output the audio distributed by the phone’s Bluetooth. Besides, it can answer incoming calls as a
Hands Free Unit. The log is as follows:
W (29327) BT_APPL: new conn_srvc id:19, app_id:1
E (164707) BT_HF: APP HFP event: CALL_IND_EVT
E (164707) BT_HF: --Call indicator NO call in progress
E (164707) BT_HF: APP HFP event: ROAMING_STATUS_IND_EVT
E (164707) BT_HF: --ROAMING: active
E (164717) BT_HF: APP HFP event: BATTERY_LEVEL_IND_EVT
E (164717) BT_HF: --battery level 1
E (165107) BT_BTM: btm_sco_connected, handle 180
E (165117) BT_HF: APP HFP event: AUDIO_STATE_EVT
E (165117) BT_HF: --audio state connected_msbc
E (165117) BT_HF: bt_app_hf_client_audio_open
I (165127) BLUETOOTH_EXAMPLE: [ * ] Receive music info from Bluetooth, sample_rates=16000, bits=16, ch=1
I (165167) AUDIO_ELEMENT: [i2s_w] AEL_MSG_CMD_PAUSE
I (165237) I2S: APLL: Req RATE: 16000, real rate: 15999.986, BITS: 16, CLKM: 1, BCK_M: 8, MCLK: 4095996.500, SCLK: 511999.562500, diva: 1, divb: 0
I (165247) AUDIO_ELEMENT: [i2s_w] AEL_MSG_CMD_RESUME,state:4
I (165247) I2S_STREAM: AUDIO_STREAM_WRITER
E (166877) BT_HF: APP HFP event: RING_IND_EVT
E (166877) BT_HF: HF_CLIENT EVT: 20
E (166877) BT_HF: APP HFP event: CLIP_EVT
E (166887) BT_HF: --clip number 18151558537
E (167657) BT_APPL: bta_dm_pm_btm_status hci_status=32
E (169947) BT_HF: APP HFP event: RING_IND_EVT
E (169947) BT_HF: HF_CLIENT EVT: 20
E (169947) BT_HF: APP HFP event: CLIP_EVT
E (169957) BT_HF: --clip number 18151558537
E (173157) BT_HF: APP HFP event: CALL_SETUP_IND_EVT
E (173157) BT_HF: --Call setup indicator INCOMING
E (173157) BT_HF: APP HFP event: BATTERY_LEVEL_IND_EVT
E (173177) BT_HF: --battery level 0
E (173267) BT_HF: APP HFP event: AUDIO_STATE_EVT
E (173267) BT_HF: --audio state disconnected
E (173267) BT_HF: bt_app_hf_client_audio_close
I (173277) BLUETOOTH_EXAMPLE: [ * ] Receive music info from Bluetooth, sample_rates=44100, bits=16, ch=2
I (173457) AUDIO_ELEMENT: [i2s_w] AEL_MSG_CMD_PAUSE
I (173487) I2S: APLL: Req RATE: 44100, real rate: 44099.988, BITS: 16, CLKM: 1, BCK_M: 8, MCLK: 11289597.000, SCLK: 1411199.625000, diva: 1, divb: 0
I (173487) AUDIO_ELEMENT: [i2s_w] AEL_MSG_CMD_RESUME,state:4
I (173497) I2S_STREAM: AUDIO_STREAM_WRITER
E (186447) BT_HF: APP HFP event: CALL_SETUP_IND_EVT
E (186447) BT_HF: --Call setup indicator NONE
I (186717) BT_LOG: bta_av_link_role_ok hndl:x41 role:1 conn_audio:x1 bits:1 features:x824b
E (211647) BT_HF: APP HFP event: CALL_IND_EVT
E (211647) BT_HF: --Call indicator call in progress
DoneA complete log is as follows:
rst:0x1 (POWERON_RESET),boot:0x1f (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:7204
load:0x40078000,len:13212
load:0x40080400,len:4568
0x40080400: _init at ??:?
entry 0x400806f4
I (27) boot: ESP-IDF v4.2.2-1-g379ca2123 2nd stage bootloader
I (27) boot: compile time 10:44:58
I (27) boot: chip revision: 3
I (31) boot.esp32: SPI Speed : 40MHz
I (36) boot.esp32: SPI Mode : DIO
I (40) boot.esp32: SPI Flash Size : 2MB
I (45) boot: Enabling RNG early entropy source...
I (50) boot: Partition Table:
I (54) boot: ## Label Usage Type ST Offset Length
I (61) boot: 0 nvs WiFi data 01 02 00009000 00006000
I (69) boot: 1 phy_init RF data 01 01 0000f000 00001000
I (76) boot: 2 factory factory app 00 00 00010000 00124f80
I (84) boot: End of partition table
I (88) esp_image: segment 0: paddr=0x00010020 vaddr=0x3f400020 size=0x2ff20 (196384) map
I (172) esp_image: segment 1: paddr=0x0003ff48 vaddr=0x3ffbdb60 size=0x000d0 ( 208) load
I (172) esp_image: segment 2: paddr=0x00040020 vaddr=0x400d0020 size=0xbbc60 (769120) map
0x400d0020: _stext at ??:?
I (471) esp_image: segment 3: paddr=0x000fbc88 vaddr=0x3ffbdc30 size=0x03514 ( 13588) load
I (477) esp_image: segment 4: paddr=0x000ff1a4 vaddr=0x40080000 size=0x1846c ( 99436) load
0x40080000: _WindowOverflow4 at /hengyongchao/esp-idfs/esp-idf-v4.2.2-psram/components/freertos/xtensa/xtensa_vectors.S:1730
I (534) boot: Loaded app from partition at offset 0x10000
I (534) boot: Disabling RNG early entropy source...
I (535) psram: This chip is ESP32-D0WD
I (540) spiram: Found 64MBit SPI RAM device
I (544) spiram: SPI RAM mode: flash 40m sram 40m
I (549) spiram: PSRAM initialized, cache is in low/high (2-core) mode.
I (557) cpu_start: Pro cpu up.
I (560) cpu_start: Application information:
I (565) cpu_start: Project name: a2dp_sink_and_hfp_example
I (572) cpu_start: App version: v2.2-252-gdd93b207-dirty
I (578) cpu_start: Compile time: Nov 26 2021 10:44:52
I (584) cpu_start: ELF file SHA256: e1f292df795c02c7...
I (590) cpu_start: ESP-IDF: v4.2.2-1-g379ca2123
I (596) cpu_start: Starting app cpu, entry point is 0x40081cd4
0x40081cd4: call_start_cpu1 at /hengyongchao/esp-idfs/esp-idf-v4.2.2-psram/components/esp32/cpu_start.c:287
I (0) cpu_start: App cpu up.
I (1490) spiram: SPI SRAM memory test OK
I (1498) heap_init: Initializing. RAM available for dynamic allocation:
I (1498) heap_init: At 3FFAFF10 len 000000F0 (0 KiB): DRAM
I (1500) heap_init: At 3FFB7468 len 00000B98 (2 KiB): DRAM
I (1506) heap_init: At 3FFB9A20 len 00004108 (16 KiB): DRAM
I (1512) heap_init: At 3FFC2838 len 0001D7C8 (117 KiB): DRAM
I (1519) heap_init: At 3FFE0440 len 00003AE0 (14 KiB): D/IRAM
I (1525) heap_init: At 3FFE4350 len 0001BCB0 (111 KiB): D/IRAM
I (1531) heap_init: At 4009846C len 00007B94 (30 KiB): IRAM
I (1538) cpu_start: Pro cpu start user code
I (1543) spiram: Adding pool of 4034K of external SPI memory to heap allocator
I (1565) spi_flash: detected chip: gd
I (1566) spi_flash: flash io: dio
W (1566) spi_flash: Detected size(8192k) larger than the size in the binary image header(2048k). Using the size in the binary image header.
I (1576) cpu_start: Starting scheduler on PRO CPU.
I (0) cpu_start: Starting scheduler on APP CPU.
I (1587) spiram: Reserving pool of 32K of internal memory for DMA/internal allocations
I (1627) BLUETOOTH_EXAMPLE: [ 1 ] Create Bluetooth service
I (1627) BTDM_INIT: BT controller compile version [ba56601]
I (1627) system_api: Base MAC address is not set
I (1637) system_api: read default base MAC address from EFUSE
I (1647) phy_init: phy_version 4660,0162888,Dec 23 2020
W (1647) phy_init: failed to load RF calibration data (0xffffffff), falling back to full calibration
W (2357) BT_BTC: A2DP Enable with AVRC
I (2387) BLUETOOTH_EXAMPLE: [ 2 ] Start codec chip
I (2387) gpio: GPIO[19]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:3
I (2647) gpio: GPIO[21]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0
I (2647) ES8388_DRIVER: init,out:02, in:00
I (2807) AUDIO_HAL: Codec mode is 2, Ctrl:1
I (2897) BLUETOOTH_EXAMPLE: [ 3 ] Create audio pipeline for playback
I (2897) BLUETOOTH_EXAMPLE: [3.1] Create i2s stream to write data to codec chip and read data from codec chip
I (2897) I2S: DMA Malloc info, datalen=blocksize=1200, dma_buf_count=3
I (2907) I2S: DMA Malloc info, datalen=blocksize=1200, dma_buf_count=3
I (2927) I2S: APLL: Req RATE: 44100, real rate: 44099.988, BITS: 16, CLKM: 1, BCK_M: 8, MCLK: 11289597.000, SCLK: 1411199.625000, diva: 1, divb: 0
I (2937) LYRAT_V4_3: I2S0, MCLK output by GPIO0
W (2937) I2S: I2S driver already installed
I (2947) LYRAT_V4_3: I2S0, MCLK output by GPIO0
I (2947) BLUETOOTH_EXAMPLE: [3.2] Create Bluetooth stream
I (2957) BLUETOOTH_EXAMPLE: [3.3] Register all elements to audio pipeline
I (2957) BLUETOOTH_EXAMPLE: [3.4] Link it together [Bluetooth]-->bt_stream_reader-->i2s_stream_writer-->[codec_chip]
I (2977) AUDIO_PIPELINE: link el->rb, el:0x3f80fde0, tag:bt, rb:0x3f80ff74
I (2977) AUDIO_PIPELINE: link el->rb, el:0x3f80fba8, tag:i2s_r, rb:0x3f811fb4
I (2987) BLUETOOTH_EXAMPLE: [ 4 ] Initialize peripherals
E (2997) gpio: gpio_install_isr_service(438): GPIO isr service already installed
I (2997) BLUETOOTH_EXAMPLE: [4.1] Initialize Touch peripheral
I (3007) gpio: GPIO[36]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:3
I (3017) gpio: GPIO[39]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:3
I (3027) BLUETOOTH_EXAMPLE: [4.2] Create Bluetooth peripheral
W (3047) PERIPH_TOUCH: _touch_init
I (3047) BLUETOOTH_EXAMPLE: [4.2] Start all peripherals
I (3047) BLUETOOTH_EXAMPLE: [ 5 ] Set up event listener
I (3057) BLUETOOTH_EXAMPLE: [5.1] Listening event from all elements of pipeline
I (3067) BLUETOOTH_EXAMPLE: [5.2] Listening event from peripherals
I (3067) BLUETOOTH_EXAMPLE: [ 6 ] Start audio_pipeline
I (3077) AUDIO_ELEMENT: [bt-0x3f80fde0] Element task created
I (3087) AUDIO_ELEMENT: [i2s_w-0x3f80fa24] Element task created
I (3087) AUDIO_PIPELINE: Func:audio_pipeline_run, Line:359, MEM Total:4271372 Bytes, Inter:218832 Bytes, Dram:187232 Bytes
I (3107) AUDIO_ELEMENT: [i2s_w] AEL_MSG_CMD_RESUME,state:1
I (3107) I2S_STREAM: AUDIO_STREAM_WRITER
I (3107) AUDIO_PIPELINE: Pipeline started
I (3117) AUDIO_ELEMENT: [i2s_r-0x3f80fba8] Element task created
I (3117) AUDIO_ELEMENT: [raw-0x3f80fcc8] Element task created
I (3127) AUDIO_PIPELINE: Func:audio_pipeline_run, Line:359, MEM Total:4265380 Bytes, Inter:214892 Bytes, Dram:183292 Bytes
I (3137) AUDIO_ELEMENT: [i2s_r] AEL_MSG_CMD_RESUME,state:1
I (3147) I2S_STREAM: AUDIO_STREAM_READER,Rate:44100,ch:2
I (3167) I2S: APLL: Req RATE: 44100, real rate: 44099.988, BITS: 16, CLKM: 1, BCK_M: 8, MCLK: 11289597.000, SCLK: 1411199.625000, diva: 1, divb: 0
I (3177) AUDIO_PIPELINE: Pipeline started
I (3177) BLUETOOTH_EXAMPLE: [ 7 ] Listen for all pipeline events
E (14397) BT_APPL: bta_av_rc_create ACP handle exist for shdl:0
W (14427) BT_APPL: new conn_srvc id:27, app_id:1
E (14437) BT_HF: APP HFP event: CONNECTION_STATE_EVT
W (14537) BT_APPL: new conn_srvc id:19, app_id:0
E (14537) BT_HF: --connection state connected, peer feats 0x0, chld_feats 0x0
E (14537) BT_HF: APP HFP event: NETWORK_STATE_EVT
E (14547) BT_HF: --NETWORK STATE available
E (14547) BT_HF: APP HFP event: CALL_IND_EVT
E (14557) BT_HF: --Call indicator NO call in progress
E (14557) BT_HF: APP HFP event: CALL_SETUP_IND_EVT
E (14567) BT_HF: --Call setup indicator NONE
E (14577) BT_HF: APP HFP event: BATTERY_LEVEL_IND_EVT
E (14577) BT_HF: --battery level 5
E (14587) BT_HF: APP HFP event: SIGNAL_STRENGTH_IND_EVT
E (14587) BT_HF: -- signal strength: 4
E (14597) BT_HF: APP HFP event: ROAMING_STATUS_IND_EVT
E (14597) BT_HF: --ROAMING: inactive
E (14607) BT_HF: APP HFP event: CALL_HELD_IND_EVT
E (14607) BT_HF: --Call held indicator NONE held
I (14617) BLUETOOTH_EXAMPLE: [ * ] Receive music info from Bluetooth, sample_rates=44100, bits=16, ch=2
I (14657) AUDIO_ELEMENT: [i2s_w] AEL_MSG_CMD_PAUSE
I (14687) I2S: APLL: Req RATE: 44100, real rate: 44099.988, BITS: 16, CLKM: 1, BCK_M: 8, MCLK: 11289597.000, SCLK: 1411199.625000, diva: 1, divb: 0
I (14687) AUDIO_ELEMENT: [i2s_w] AEL_MSG_CMD_RESUME,state:4
I (14697) I2S_STREAM: AUDIO_STREAM_WRITER
E (14707) BT_HF: APP HFP event: CONNECTION_STATE_EVT
E (14717) BT_HF: --connection state slc_connected, peer feats 0x3ef, chld_feats 0x3f
E (14717) BT_HF: APP HFP event: INBAND_RING_TONE_EVT
E (14717) BT_HF: --inband ring state Provided
I (29317) BT_LOG: bta_av_link_role_ok hndl:x41 role:1 conn_audio:x1 bits:1 features:x824b
W (29327) BT_APPL: new conn_srvc id:19, app_id:1
E (164707) BT_HF: APP HFP event: CALL_IND_EVT
E (164707) BT_HF: --Call indicator NO call in progress
E (164707) BT_HF: APP HFP event: ROAMING_STATUS_IND_EVT
E (164707) BT_HF: --ROAMING: active
E (164717) BT_HF: APP HFP event: BATTERY_LEVEL_IND_EVT
E (164717) BT_HF: --battery level 1
E (165107) BT_BTM: btm_sco_connected, handle 180
E (165117) BT_HF: APP HFP event: AUDIO_STATE_EVT
E (165117) BT_HF: --audio state connected_msbc
E (165117) BT_HF: bt_app_hf_client_audio_open
I (165127) BLUETOOTH_EXAMPLE: [ * ] Receive music info from Bluetooth, sample_rates=16000, bits=16, ch=1
I (165167) AUDIO_ELEMENT: [i2s_w] AEL_MSG_CMD_PAUSE
I (165237) I2S: APLL: Req RATE: 16000, real rate: 15999.986, BITS: 16, CLKM: 1, BCK_M: 8, MCLK: 4095996.500, SCLK: 511999.562500, diva: 1, divb: 0
I (165247) AUDIO_ELEMENT: [i2s_w] AEL_MSG_CMD_RESUME,state:4
I (165247) I2S_STREAM: AUDIO_STREAM_WRITER
E (166877) BT_HF: APP HFP event: RING_IND_EVT
E (166877) BT_HF: HF_CLIENT EVT: 20
E (166877) BT_HF: APP HFP event: CLIP_EVT
E (166887) BT_HF: --clip number 18151558537
E (167657) BT_APPL: bta_dm_pm_btm_status hci_status=32
E (169947) BT_HF: APP HFP event: RING_IND_EVT
E (169947) BT_HF: HF_CLIENT EVT: 20
E (169947) BT_HF: APP HFP event: CLIP_EVT
E (169957) BT_HF: --clip number 18151558537
E (173157) BT_HF: APP HFP event: CALL_SETUP_IND_EVT
E (173157) BT_HF: --Call setup indicator INCOMING
E (173157) BT_HF: APP HFP event: BATTERY_LEVEL_IND_EVT
E (173177) BT_HF: --battery level 0
E (173267) BT_HF: APP HFP event: AUDIO_STATE_EVT
E (173267) BT_HF: --audio state disconnected
E (173267) BT_HF: bt_app_hf_client_audio_close
I (173277) BLUETOOTH_EXAMPLE: [ * ] Receive music info from Bluetooth, sample_rates=44100, bits=16, ch=2
I (173457) AUDIO_ELEMENT: [i2s_w] AEL_MSG_CMD_PAUSE
I (173487) I2S: APLL: Req RATE: 44100, real rate: 44099.988, BITS: 16, CLKM: 1, BCK_M: 8, MCLK: 11289597.000, SCLK: 1411199.625000, diva: 1, divb: 0
I (173487) AUDIO_ELEMENT: [i2s_w] AEL_MSG_CMD_RESUME,state:4
I (173497) I2S_STREAM: AUDIO_STREAM_WRITER
E (186447) BT_HF: APP HFP event: CALL_SETUP_IND_EVT
E (186447) BT_HF: --Call setup indicator NONE
I (186717) BT_LOG: bta_av_link_role_ok hndl:x41 role:1 conn_audio:x1 bits:1 features:x824b
E (211647) BT_HF: APP HFP event: CALL_IND_EVT
E (211647) BT_HF: --Call indicator call in progress
DonePlease use the following feedback channels:
- For technical queries, go to the esp32.com forum
- For a feature request or bug report, create a GitHub issue
We will get back to you as soon as possible.