printer_mods

Mods

Printer mods for Voron 3D printers Remember to update this README when uploading new mod!

Legacy printers

Mods for legacy printers can be found here. If one of your mods applies to a current generation Voron printer, contact the admins in Discord to have your mod moved to this folder.

Table structure

Update the following table with the information about your mod:

• Your name
• A link to your sub-folder
• A short description of your mod
• The printer compatibility. Use :heavy_check_mark: for ✔️,:x: for ❌ and :grey_question: for ❔

like so: | Creator | [Mod title](link) | Description | :x: | :x: | :x: | :x: | :x: |

---

Creator	Mod title	Description	V0	V1.8	V2.4	VSW	Trident
1-0-R	V2.4 handle	Handle for Voron 2.4	❌	❔	✔️	❌	❔
120decibell	Side entry exhaust housing	Exhaust housing with dual cover screws and single or dual side entry filament paths.	❌	✔️	✔️	❌	✔️
	Huvud Chain Mount	Huvud rear mount for Clockwork or LGX that supports a cable chain.	❌	✔️	❔	❌	✔️
3dpandme	FANnypack zero	Electronics cooling solution for Voron Zero	✔️	❌	❌	✔️	✔️
	Thermistor holder zero	Extended thermistor holder for Voron Zero	✔️	❌	❌	✔️	✔️
3vilson	V0.1_Skirt_Inlet	Skirt with C14 inlet + New feet to screw into	✔️	❌	❌	❌	❌
	V0.1_Skirt_Holes	Skirt with Access Holes from the bottom	✔️	❌	❌	❌	❌
42bios	Corner panel clip w. cable	Corner panel clip with an internal cable path.	❌	❔	✔️	❌
	Exhaust filter housing - side thread	Exhaust filter housing with the G1-8 "thread on the side.	❌	❔	✔️	❌
	LED mount	AngryLED - LED-mount for Lumentech LT3 profiles.	❌	❔	✔️	❌
	relay mount	relay-mount for 2x 2 channel relay modules.	❌	❔	✔️	❌
ademuri	Lights, Camera, Voron	A mount for LED strips and Picam for the V0.1	✔️	❌	❌	❌	❌
aeresov	TL filament sensor bracket	A bracket for TL filament sensor to mount near stock spool holder.	❌	❔	✔️	❌
	MeanWell UHP-xxx DIN mount	A bracket for MeanWell UHP series PSU (200, 350 and 500) to mount it across 2 DIN rails.	❌	❔	✔️
	Raspberry Pi DIN mount	A bracket for Raspberry Pi 3/4 to mount it onto DIN rail, along or across.	❌	❔	✔️
	SKR 1.3/1.4 DIN mount	A bracket for SKR 1.3/1.4 board to mount it onto DIN rail, along or across.	❌	❔	✔️
	cable tie DIN mount	A bracket for cable ties to route cables across DIN rails.	❌	❔	✔️
Akio	Hidden cable routing z belt cover	Z belt covers that allow hidden cable routing.	❌	❌	✔️	❌	❌
alanho	BTT PITFT50 v2 Mount	A mount for the BTT PITFT50 v2 Touch Display	❌	❔	✔️	❌
albert	IKEA Dioder Led Mount	A mount for the IKEA Dioder LED strip	❔	❔	✔️	❌
al3ph	LED Mount	A mount for 10mm LED WS2812 strips	✔️	❌	❌	❌
	Analog Timer Mount	A skirt mount for analog timer	✔️	❌	❌	❌
	Filament Runout Sensor	A simple filament runout sensor	✔️	✔️	✔️	✔️
	PL05 Sensor Mount	A mount PL05 inductive sensor	✔️	❌	❌	❌
AlexanderT-Moss	270 Clamping Hinges	Simple 270 degree hinges that clamp to the front panels instead of using VHB or drilled holes	❌	❔	✔️	❌	❔
Andre	Mini Afterburner Strain Relief	A replacement strain relief for the Mini Afterburner toolhead	✔️	❌	❌	❌
	V0 Neopixel Front Bed Mount	A replacement Front Bed Mount with room for a neopixel or dotstar behind the logo	✔️	❌	❌	❌
	Mini Afterburner ADXL345 Mount	Mount for an AXDL345 on the Mini Afterburner	✔️	❌	❌	❌
	Revo Nozzle Skirt	A Revo nozzle box hidden in a Trident skirt.	❌	❌	❌	❌	❌
antoinecellerier	DS18B20 Sensor Mount	DS18B20 temperature sensor mount	✔️	❌	❌	❌	❌
ardichoke	V0 Long Thumb Nut	Taller thumb nuts for V0 bed	✔️	❌	❌	❌	❌
arkeet	Dial test indicator mount	A toolhead mount for a dial test indicator, where the tip is located at the nozzle.	❌	✔️	✔️	❌
	Magnetic hotend fan cover	A replacement hotend fan cover, held with magnets instead of screws.	❌	✔️	✔️	✔️
	MGN12 X-axis	Replaces the dual MGN9H rails with a single MGN12H.	❌	❌	✔️	❌
	V0 DC inlet	Skirt inlet for external 24V DC power supply.	✔️	❌	❌	❌
aTinyShellScript	RS PSU DIN Bracket	DIN brackets for MeanWell RS PSUs with 80mm spacing.	❔	❔	✔️	❔	❔
baccula	Revo Nozzle Holder for v2.4 350	A remix of Andre's design allowing for skirt storage of 4 E3D Revo nozzles in the skirt of your 350mm v2.4.	❌	❌	✔️	❌	❌
Backenfutter	Mount for Electreeks Camera	This Mod is a simple "One Piece" mount for the popular Electreeks Camera.	❔	❔	✔️	❌	❔
Badnoob	Precision AB Drive	Changes the gearing for the AB drives to improve both resolution and torque, with a strenthened frame.	❔	❔	✔️	❌
	AB-BN Afterburner mod (5015)	Improved Afterburner with 5015 fan	❌	✔️	✔️	✔️	✔️
	AB-BN for Stock Afterburner (4020)	Improved Dragon and Rapido toolhead for stock Afterburner with 4020 fan	❌	✔️	✔️	✔️	✔️
	Rail Alignment	Tools and procedure to properly align the rails in 2.4 and Afterburner	❌	❌	✔️	❌
Baltojikale	LoudOwl aka Stabby	Alternative dual 5015 part cooling fan toolhead for Afterburner	❌	✔️	✔️	✔️
beaugalbraith	Nova Printhead	Use Nova Hotend with Afterburner	❔	❔	✔️	❔	❔
BladeScraper-Designs	Microswitch Pod With Connector	Microswitch pod with JST-XH 4-pin connector	❌	❌	✔️	❌
	Horizontal Spool Holder	Based on the stock holder but mounts to the horizontal extrusions.	❌	❔	✔️	❔
	CornerPanel_SpoolHolder	A better supported Spool Holder that mounts to a modified corner panel.	✔️	❌	❌	❌	❌
Blamm	LRS-100 DIN mount	DIN rail mount for an extra LRS-100 Power Supply	❌	✔️	✔️	❔	✔️
BlueBear	Deck Panel Backpack	A mounting alternative if you don't want to drill your deck panel	✔️	❌	❌	❌
	Clippable Wago 221 Mounts	Mounts for Wago 221 to screw or clip-in on 1515 extrusions	✔️	❌	❌
	Ziptie Mount	Clippable Ziptie hooks for 1515 extrusions	✔️	❌	❌
bobbleheed	Magnetic Panels	Magnetic clips to allow for easy removal and installation of panels	❌	❔	✔️	❌	❔
	Filament Runout Sensor	Filament runout sensor that replaces the stock bowden retainer	❌	✔️	✔️	❌	✔️
Boingomw	Wago mount	Smaller 5 port Wago mount that fits parallel to the support rails	❌	❔	✔️	❌	❔
Bondtech	Mini-After-LGX-Lite	LGX Lite Toolhead Setup For Voron V0.1.	✔️	❌	❌	❌	❌
btp	Galileo chain mount (befenybay)	Modified chain mount position to cater for difference with Galileo Clockwork	❌	❌	❌	✔️
buzzdalf	v1.8/2.4 Afterburner connector cover for 42STH20-1004AS	v1.8/2.4 Connector cover for 42STH20-1004AS	❌	✔️	✔️	❔
	Ender 3 Switchwire Taller Z Mod	Taller Z Mod	❌	❌	❌	✔️
	Ender 3 Switchwire Y Tensioner Mod	Y Tension Mod	❌	❌	❌	✔️
ByteChild	ESP32 DIN Rail Bracket	DIN rail mounting bracket for an ESP32	❌	❔	✔️	❌
	2-Channel Relay DIN Rail Bracket	DIN Rail mounting bracket for an 2-Channel-Relay	❌	❔	✔️	❌
bythorsthunder	MGN9 Backers Idlers	New idler uppers for MGN9 Extrusion backers	❌	❌	✔️	❌	❌
	Stealthburner Rapido UHF	Stealthburner mod for Rapido UHF	❌	❌	✔️	✔️	✔️
CannedBass	Trident Bed Fans	Bed fans for Trident	❌	❔	❌	❌	✔️
	PITFT50 45-degree mount	Mount that puts the screen at a 45-degree angle for more vertical clearance	❌	❔	✔️	❌	✔️
Ch4rlesB	V0 Handles Slim	Simple and slim handles for the V0	✔️	❌	❌	❌
Chaoticlab	Tool_free_tensioner	Tool-free tensioner for Z-Axis	❌	❌	✔️	❌
ChenTheDesignMaker	Z Belt Clip	Simple clip to keep extra Z belts clean and away from panels	❌	❌	✔️	❌	❌
chirpy	V0.1 Raised Tophat	Alternative Tophat design that uses stock panels and raises height by 30mm	✔️	❌	❌	❌	❌
	V0.1 Nozzle Wiper	Servo powered nozzle wiper and purge bucket	✔️	❌	❌	❌	❌
	Runout UnKlicky Sensor	Runout UnKlicky Sensor is a filament runout sensor with mounts for 1515 and 2020 extrusions	✔️	✔️	✔️	✔️	✔️
chrisrgonzales	270° Front Panel Hinge	Hinges that have 270° of swivel, parametric CAD included	❌	❌	✔️	❌
christophmueller	Phaetus and Zodiac Dragonfly BMO Afterburner toolheads	Covers both the original Phaetus variant as well as the Zodiac one.	❌	✔️	✔️	✔️
chri.kai.in	20x20mm Profile Covers	Provide overlapping and flush slot covers for 20x20mm slot6 construction profiles	❌	✔️	✔️	✔️	✔️
	Angry CAM USB	Housing for small USB camera module, allowing mounting to gantry or frame profiles	❌	❔	✔️	❔	❔
	Exhaust Adapter 100mm	Replace 60mm exhaust fan with 100mm ventilation system adapter	❌	✔️	✔️	❌	✔️
claytono	Fysetc S6 V2 Mount	DIN Mount for the Fysetc S6 V2 controller	❌	✔️	✔️	❌
	Voron 2.4 Extrusion Jig	A jig help align extrusions to get a properly square frame	❌	❌	✔️	❌
	V0 Zip Tie Skirts	V0 skirts with small loops added along the top to allow zip tyiing cables to them	✔️	❌	❌	❌
clee	Monster8 DIN Rail Mounts	DIN mount for Makerbase Monster8 V1/V2 controller	❌	❌	✔️	❌	✔️
cmrny	V0.1 Motor Panel Modification	V0.1 Motor panel modification to keep umbilical and bowden tube from rubbing against motor belts	✔️	❌	❌	❌	❌
Conqueror433	Voron Parts Logo	Voron Parts Logo for your back panels, 3D Print or Laser Cut	❌	❌	✔️	❌
	Voron V0.1 Parts Logo	Voron Parts Logo for your V0 deck panel	✔️	❌	❌	❌
consibonsi	Y-Mod SW 9mm	9mm Y belt mod for SW	❌	❌	❌	✔️
csch0	SW Fan Mount No Tape	60x20 Fan Mount for SW without tape	❌	❌	❌	✔️
d3nny	Filtered Power Plug with RND_165-00057	Filtered Power Plug for RND 165-00057 and CAT6-Plug	❌	❌	✔️	❌
D4rkCelerity	Raspberry Pi Zero Bracket	Modified version of Trident RPi bracket to fit the smaller RPi Zero	✔️	✔️	✔️	❌	✔️
DaGlo	V0.1 Duet 2 Wifi mounting brackets	Voron 0.1 Mounting brackets with/without RPi 4	✔️	❌	❌	❌
	Voron V0 Mean Well power supply bracket (Funssor Kit)	Voron V0 Mean Well power supply bracket (Funssor Kit)	✔️	❌	❌	❌
	Voron V0 SSR Mount	Voron V0 SSR Mount for the bottom	✔️	❌	❌	❌
DaGrooch13	Tophat Exhaust Filter V0	Activated charcoal exhaust filter with HEPA that replaces the rear tophat panel	✔️	❌	❌	❌
Dan88	V0 one-part Skirts	One part Skirts for the V0	✔️	❌	❌	❌
DaStivi	The Cephalopod limb (BTT Octopus PRO Bracket(s))	An alternative Din rail mount for BTT Octopus (PRO) boards	❔	✔️	✔️	✔️	✔️
Daten	Revo hotend skirt case	A skirt case for the Revo hotends to reside R1 and R2	❌	❌	✔️	❌	❌
davidauvergne	Center_cable_management_duct	Mod for a centered cable management	❌	❌	:✔️:	❌	❌
DC67	Plug Panel Mod for Schaffner FN286-10-06	A modified plug panel for the Power Entry Connector Schaffner FN286-10-06 with two integreated Keystone sockets.	❌	❔	✔️	❌
deepfriedheroin	V2 Bed Wagos	Wire management for the v2 bed	❌	❌	✔️	❌
	v0 Wago Bed Mounts	Easy to install Wago mounts for the v0	✔️	❌	❌	❌
	v0 Power Wagos	Easy to install Wago mounts for v0 mains	✔️	❌	❌	❌
dePrintinator	HEPA Exhaust	HEPA filter chamber exhaust replacement.	❌	✔️	✔️	❌	✔️
DerekBackus	Trident Right Skirt Switch	Moves power switch to right front skirt on the Trident	❌	❌	❌	❌	✔️
	LED Strip Holder	Simple bracket to mount an LED strip	❌	❌	✔️	❌	✔️
Derpimus	V0.1 Block Handle	V0.1 Block Style Handle	✔️	❌	❌	❌
DorjeDorf	Duet 3 6HC Din Bracket	V2.4 Duet 3 6HC Din Bracket	❌	❌	✔️	❌
	Duet 3 3HC Din Bracket	V2.4 Duet 3 3HC Din Bracket	❌	❌	✔️	❌
doubletrouble	V0 Skirt Mod	V0 Skirt Mod	✔️	❌	❌	❌
Dr-Info	Corner Cable Cover with Drop Holes	Corner cable cover around Z-idler with drop holes near z frame and cutouts for inline wiring from 2020 extrustions	❌	❌	✔️	❌	❌
DrGhetto	Ghetto Panels	Printed panels for the Voron Zero	✔️	❌	❌	❌
eamars	Stealthburner (RC1) Dragon Volcano Hotend Toolhead Mount	The Stealthburner toolhead mount for Mellow Crazy, TriangleLab T-Volcano and Phaetus UHF mini	❌	✔️	✔️	✔️	✔️
eddie	V1.8 12mm Z Mod	Add V1.8 option for 12mm Z rods	❌	✔️	❌	❌
	LED Bar Clip	Modular LED Clip for mounting LED Strip to 2020 Extrusions	❌	✔️	✔️	❌	✔️
edwardyeeks	Tridentified V2.4 Power Inlet	Trident style side power inlet for V2.4 using Z Drive Motor Tensioner Mod - By @Amarpal89	❌	❌	✔️	❌	❌
elcrni	V.24/Trident Spool Holder	Spool holder that mounts on top for "too close to the wall" printers	❌	✔️	✔️	❌	✔️
	Trident Internal Spool Holder	Internal spool holder for 300 and 350 Tridents. Supports full size 1kg spool	❌	❌	❌	❌	✔️
Electroleon	U2C Mounting	Bigtreetech U2C CAN Interface mounting bracket	✔️	✔️	✔️	❔	✔️
Ellis	15x15 Drag Chain End	15x15 drag chain end piece	❔	❔	✔️	❔
	Badge Retractor Mount	Extrusion mount for badge retractor to keep bowden tube out of the way.	❔	❔	✔️	❌
	Bed Fans	Bed fan control macros and 5015 bed fan mounts	❌	❌	✔️	❌
	Short Z Joints	Shorter Z joints for the v2.4	❌	❌	✔️	❌
	Single MGN9H Carriage	Single MGN9H toolhead carriage with toolhead x endstop support (for umbilical)	❌	✔️	✔️	❔
ElPoPo	Removable Doors	New hinge to easily remove the door and have a wide opening V2.x	❌	❌	✔️	❌
Empusas	Power Skirt 2.x FN284-10-06	Power Skirt for Schaffner FN284-10-06 V2.x	❌	❌	✔️	❌
	Mounts for Terminal Blocks NC933 SPL-62	Mounts for Terminal Blocks NC933 and SPL-62 from AliExpress	❔	❔	✔️	❔
	Mounts for BTT Filament Motion Sensor	Mounts for Big Tree Tech Smart Filament Motion Sensor	✔️	✔️	✔️	✔️
evandepol	Crydom GN Terminal Guard	A simple safety guard for the terminals on a Crydom GN SSR	❌	❌	✔️	❌
	Voron 2.4 cable clamps	A set of 2020-mounted cable guards to organize and dress the wiring on your build	❌	❌	✔️	❌
falo	Magnetic Exhaust Grill Cover	A magnetic cover to seal the filtered exhaust	❌	❌	✔️	❌
	Toolhead PCB to CAN Mount Adaptor	A mount to enable side mounting of a CAN board (Huvud/SHT42) in Afterburner PCB spacing	❌	✔️	✔️	✔️	✔️
	LGX Lite CAN Side Mount	A side mounting for a CAN board (Huvud/SHT42) to the LGX Lite	❌	✔️	✔️	✔️	✔️
Fiction	C270 mount	Logitech C270 webcam front-centre mount	❌	❌	✔️	❌	✔️
	Crossrail	Across-the-rails LRS-200-24 or RSP-200-24 mount using DRP-03 brackets	❌	❌	✔️	❌	✔️
	Exhaust_cover	Cover for exhaust cutout in back panel	❌	❌	✔️	❌	✔️
	Exhaust_cover_SFS	Exhaust cover and BTT Smart Filament Sensor mount	❌	❌	✔️	❌	✔️
	LGX Lite toolhead PCB mount	Mount for Hartk's toolhead PCB(s) for LGX Lite	❌	✔️	✔️	✔️	✔️
filotto78	6mm slot cover	Simple cover for extrusion with 6mm slot width	❌	❔	✔️	❔	❔
FreeformFez	V1.8 Filtered Power Inlet	V1.6 Filtered Inlet and Rocker Switch for V1.8	❌	✔️	❌	❌
GadgetAngel	Cricut Voron Logos	For any cutting machines or machines that rely on vector graphics and use .svg files. These vectors or .svg files are the Voron Design Logos for the Voron 2.4, Voron SwitchWire, Voron 0.0/0.1. and Trident These .svg files use a minimal amount of anchor points to achieve the vector shapes!	✔️	❌	✔️	✔️	✔️
	Bed Support Extrusions Alignment Tools	The bed support alignment tools will assist in helping align the "bed support extrusions" to the frame. When the alignment tools are placed in all four corners of the Voron Printer's frame the "bed support extrusions" will butt up against these tools so that you can screw the "bed support extrusions" down to the printer's frame in the correct position.	❌	❌	✔️	❌	❌
Galvanic	Bowden Tube Guide	Bowden tube guide and CANBUS wire support	❌	✔️	✔️	❌	✔️
gamebofh	Laser cut door panels	Files to allow you to create laser cut door panels with some ability to adjust		❌	❔	✔️	❔
gauravmm	Crazy Mozzie HF toolhead SB+CW2	Toolhead for Crazy Mozzie HF, compatible with Stealthburner and Clockwork 2	❌	✔️	✔️	✔️	✔️
gen2ng	Switchwire LED wire pass through	Z Carriage Stop modification that makes pass through of wires for the LED light bar clean and easy	❌	❌	❌	✔️	❌
geoffreyyoung	FYSETC SPIDER DIN Bracket	FYSETC SPIDER DIN Bracket	❌	✔️	✔️	❌
	Dual Rail Installation Guide	Rail installation guide that also works for the 2.4 dual rail installation	❌	❌	✔️	❌
	LGX Info, Links, and Models	Useful information and models for using the Bondtech LGX extruder wth Afterburner	❌	✔️	✔️	✔️	✔️
gerritwellen	Manta M8P Mount	Mounting Bracket for BTT Manta M8P	❌	❔	✔️	❌	✔️
GiulianoM	Fly F407ZG Mount	Mount for the Fly F407ZG: https://github.com/FLYmaker/FLYF407ZG	❌	❌	✔️	❌
Gizzle	Ender 3 and Ender 3 Pro Switchwire Mod	Mod for the Ender 3 and Ender 3 Pro, which adapts the kinematics and most other parts of the Voron Switchwire.	❌	❌	❌	✔️
GSL12	Pocketwatch Nema 17	Extruder like Pocketwatch, but with Nema17 instead of Nema14. Maybe for V0 fork with 2020 extrusions, Nema17 and MGN9 or other printers.	❔	❔	❔	❌
Golas	V0.1 Extended tophat hinge	Extended tophat for v0.1 with hinges (integrated or screwed ones).	✔️	❌	❌	❌	❌
	V0.1 Trident skirt remix with 12864 LCD	Trident style v0.1 skirt mix with 12864 Mini Lcd on front or plain skirt.	✔️	❌	❌	❌	❌
hhammarstrand	Afterburner connector cover for 42STH20-1004AS	Connector cover for 42STH20-1004AS	❌	❌	❌	✔️
hartk1213	Voron0 deck panel	Used @Kruppes blank deck panel to add the logo as well as the name VORON0	✔️	❌	❌	❌
	Voron0 display dualcolor	Added a dual color file for the Voron Display Front housing	✔️	❌	❌	❌	❌
	Voron0.2 2.8 Waveshare Display	2.8 Waveshare display for V0.2	✔️	❌	❌	❌	❌
	Voron0 C14Inlet	Added a new Power inlet that uses a Fused C14 plug and switch that covers the mains contacts	✔️	❌	❌	❌	❌
	Voron0.2 Rear Keystone Skirt	Added keystone slot on rear skirt for V0.2	✔️	❌	❌	❌	❌
	Voron0 Hinged Top Hat	Created a new hinged top hat design for the V0 so it can fold away when you dont want a top hat on	✔️	❌	❌	❌	❌
	Voron0 ExtendedLegs	New extended legs to raise the printer up a tiny bit more	✔️	❌	❌	❌	❌
	Voron0 ExtrusionSkirt	Created a new skirt design that uses 50mm extrusions as legs and it has a c14 power inlet hole on the bottom	✔️	❌	❌	❌	❌
	Voron0 MGN9C X Axis	This mod, replaces the stock MGN7H for MGN9C on the V0	✔️	❌	❌	❌	❌
	Voron2.4 and Trident Pins Mod	This mod replaces all the M5 screws for all idlers/pulleys/bearings with 5mm pins	❌	❌	✔️	❌	✔️
	Voron2.4 Y Endstop Relocation	This mod relocates the Y endstop to the top A drive piece	❌	❌	✔️	❌	❌
	Voron2.4 GE5C	This mod replaces the stack of printed z joints with a metal spherical bearing	❌	❌	✔️	❌	❌
	Voron2.4 SexBolt ZEndstop	This mod replaces stock V2 Z endstop with a different style	❌	❌	✔️	❌	✔️
henrikssn	Plug Panel Mod for Generic Unfiltered Modules	v2.4 plug panel for generic unfiltered modules with 66mm x 27mm cutout such as the Delta 06A2 and Qualtek 761-18	❌	❌	✔️	❌
	Parametric Spool Holder	Spool holder where the length is a parameter.	❌	✔️	✔️	❌	✔️
hergtoler	Exhaust Housing for 120mm Fan and 4in Duct	v2.4 Exhaust Housing for 120mm Fan and 4in Duct	❌	❌	✔️	❌	❌
hernsl	Bottom Panel Mag Clip	v2.4 magnetic clips to retain bottom panel	❌	❌	✔️	❌
hijax_pl_	Corner panel clip	V2 panel corner frames using 3-way L brackets in the corners	❌	❌	✔️	❌
	Din Rail mount	Adapter to attach DIN Rail to 2020 extrusion.	❌	❌	✔️	❌
	Controler Board adapters	DIN (rotated) and legacy adapters for boards like SKR mini E3.	❔	❌	✔️	❌
hobson318	Klipper Expander Mount	Mounting brackets for the klipper expander using vhb tape or mounting screws	✔️	✔️	✔️	✔️	✔️
	Belt Tension Wrench	Wrench for easier turning of the belt tension knobs on V0.1	✔️	❌	❌	❌	❌
hoschi	FYSETC Spider DIN Rail Mount	DIN rail mount for FYSETC Spider	❌	❔	✔️	❔
hymness1	Quickdraw probe Voron Switchwire	Detachable magnetic probe with docking system for VSW	❌	❌	❌	✔️	❌
	10x11mm chain VSW	Printable and openable 10x11mm chain	✔️	❔	❔	✔️	❔
Iakabos	c920 Mount	Slim mount for logitech c920 webcam	❌	✔️	✔️	❌
	V0 beltchains	Modified beltchain parts for V0 Z cables	✔️	❌	❌	❌
iblue	V0.1 Tophat Extractor	Tophat Extractor for the Voron V0.1 with activated charcoal and HEPA filter	✔️	❌	❌	❌	❌
jappaj	V0.1 FanSaver	A printable fix for overheating V0.1 blower fans	✔️	❌	❌	❌	❌
jasonc	V2.4 Z-Idler Shoulder Bolt Mod	Modification to the idler carriers to accept a 25mm shoulder bolt. Ideal for Gates idlers.	❌	❌	✔️	❌
Jasrags	Feed slot with filament pass-through	A feed slot with a filament pass-through	❌	❌	❌	✔️	❌
jatson	Plug panel mod for Schurter CD44.1101.151 power entry	A modified plug panel for Voron 2.4r1 with Schurter CD44.1101.151 power entry modul. The panel has a LAN socket as well.	❌	❔	✔️	❌	❌
jaysuk	4.3 Fly Screen Mount	A mount for a 4.3" Fly Screen	✔️	❌	❌	❌	❌
JD	V2.4 Filament runout sensor	Replace the 2.4 stock bowden tube holder and add a filament runout sensor	❌	✔️	✔️	❔	✔️
jeoje	V2.4 Z Chain Guide with Integrated Chamber Thermistor Mount	Modifies the Z chain guide to hold a chamber thermistor	❌	❌	✔️	❌
	4.3" Touchscreen Mount	Mounts a Waveshare 4.3inch Capacitive Touch Display to v2.4 and Switchwire Vorons	❌	❌	✔️	✔️
	Sturdy Handles	Modified v2.2 handles with no panel rest and with 4 anchor points	❌	❔	✔️	❌
	Molex MLX and Microfit 3.0 Bed Connector Mount	Solid mount your bed connectors	❌	❌	✔️	❌
JeremyRuhland	V2.4 Plug Panel Generic Combo	Skirt power panel for generic amazon plug/switch/fuse combo module, with 2 keystone sockets	❌	❌	✔️	❌	❌
jgehrig	V0 LCD Touchscreen Skirt	3.2" LCD Touch Screen Skirt	✔️	❌	❌	❌
JJFX	V2.4 CR Touch Snap Mount	Mount to replace v2.4 (MGN9) probe with a Creality CR Touch	❌	❔	✔️	❌	❌
JNP	Back Door	Door for easy hardware access	✔️	❌	❌	❌
	Deck Panel	Covers the hotbed cables	✔️	❌	❌	❌
	Drawer	Drawer in four different versions	✔️	❌	❌	❌
	Front Door	Door in a frame	✔️	❌	❌	❌
	Hepa Filter	Filter case with fan´s	✔️	❌	❌	❌
	Mid Panel	Panel for SKR1.4/1.4 or SKR E3 mini mount	✔️	❌	❌	❌
	Neopixel Case	mounting for Neopixel strip with 8 LED´s	✔️	❌	❌	❌
	Side Panels	Panels with intergrated hinge	✔️	❌	❌	❌
johanncc	Raspberry Pi Camera Mount	Low profile raspberry pi camera mount	✔️	❌	❌	❌	❌
Jon	1515 LED Mount	Snap in 1515 Led mount for WS2812B	✔️	❌	❌	❌	❌
	adxl345 skirt keystone	Skirt keystone for ADXL345 using Microfit 3.0	❌	❌	✔️	❔	❔
joposter	V0 Clippable LED Caselight	LED Case light for the V0 that clips into the extrusions	✔️	❌	❌	❌	❌
JosAr	Klicky Probe	Microswitch based inductive probe replacement	✔️	✔️	✔️	❌	✔️
KageUrufu	Euclid Probe Carriage	A MGN-12 carriage with an inset mount for a Euclid Probe	❌	✔️	✔️	❔	✔️
KenadyDwag44	Switchwire Lightbar	A LED lightbar for switchwire	❌	❌	❌	✔️
KevinAkaSam	VEFACH	Voron Exhaust Filter Inserts for Activated Coal + Hepa	❌	❔	✔️	❌	✔️
Khay	V0 Micro Backplate	Minimalistic backplate for cooler motors and electronics	✔️	❌	❌	❌	❌
	Fan for V2-200mm²	Middle Skirt for V2-200mm² Electronics Compartment	❌	❌	✔️	❌	❌
	3x Keystone PlugPanel	PlugPanel with Options for 3 Keystones	❌	❌	✔️	❌	❌
KiloQubit	V0 Reverse Bowden Mount	V0 reverse bowden mount	✔️	❌	❌	❌
	V2.4 Z Chain Mounts for 3 Hole Chains	Z chain mounts for 3 hole generic chain	❌	❌	✔️	❌
	Trident Schurter Inlet Skirt	Trident inlet skirt for mounting a Schurter DD11.0124 or similar inlet	❌	❌	❌	❌	✔️
kirby	V0 Sherpa Mini Direct Drive Mod	A direct drive mod for the V0 using the Annex Sherpa Mini extruder	✔️	❌	❌	❌
Koios	6mm Tempered Glass Mod	Lock levers and rests for 6mm Tempered glass panels	❌	❌	✔️	❌
	C920 Low Profile Mount	Low profile mount for a C920 Webcam	❌	❌	✔️	❌
	LED Bar Mounts	Low profile mount for led bar lights	❌	❌	✔️	❌
	V0 C920 Tophat Mount	Mounting bracket for a Logitech C920 on the tophat	✔️	❌	❌	❌
Kosh42EFG	Kirigami bed front	Printed bed front for kirigami folded metal bed mount with Voron logo.	✔️	❌	❌	❌	❌
Kruppes	Belt Tension Meter	Print in place tension meter to easily tighten multiple belts to the same tension	✔️	✔️	✔️	✔️
	Encosed Bottom	Modified printed parts and panel to fully enclose V0.	✔️	❌	❌	❌
	V0 Printed Deck with inserts	Electronics Deck Panel using brass heat inserts. Optional with accent color Voron Logo.	✔️	❌	❌	❌
Kyleisah	CableGator Cable Comb	A cable comb for simplifying and tidying wire harnesses for printers with drag chains	✔️	✔️	✔️	✔️	✔️
lakai	Bruag Skirts	V2 350mm skirts inspired by Bruag Facades	❌	❌	✔️	❌
Le0n	Magnetic panels with Magnet Inserts	Magnetic panel mounts with magnets inserted into frame slots.	❌	✔️	✔️	❌	✔️
leandromarceddu	PowerSkirt	Modified skirtpiece for a digital power monitor	❌	❔	✔️	❔
littleferris	V0 c14 Skirt Inlet	V0 C14 Skirt inlet	✔️	❌	❌	❌
LJ	Scrubby	Easy to use filament dust filter	✔️	✔️	✔️	✔️	✔️
LoCoCNC	MGN7H Shims	Shims for making bearing cartridges coplanar	✔️	❌	❌	❌
	Mosquito PTFE 15mm Tube Cutting Jig	Tool to precicely cut 15mm PTFE Tube	✔️	❌	❌	❌
	3mm Top Hat Panels Clips	Required to use the 3mm (1/8") thick top hat panels for V0.1	✔️	❌	❌	❌
	Strain Relief w/ 10 Pin Microfit	Strain Relief with 10 pin Microfit connector	✔️	❌	❌	❌
	SSR Mounting Strap	Mounting Strap for SSR on 1515 Extrusions	✔️	❌	❌	❌
	V2.4 Bed Wiring Grommet	Safely capture your bed wires thru the bottom panel	❌	❌	✔️	❌
LoganFraser	ComboInlet	Skirt pieces for Trident, 2.4 and 2.4r2 for combo inlets in 2 sizes.	❌	❌	✔️	❌	✔️
	HorseshoeSpoolHolder	Horseshoe Spool Holder - mounts internally for Trident, or externally for V0, V1, or V2 printers.	✔️	✔️	✔️	❌	✔️
	PiPlate	PiPlate - Raspberry Pi3,4 mounting plate and Skirt Mod for V2.4/Trident	❌	❌	✔️	❌	✔️
	Trident Inverted Electronics	Flip the Trident electronics bay for top access.	❌	❌	❌	❌	✔️
	WagoMounts	Wago Mounts for Din Rail or 2020 Extrusion mounting.	❔	❔	✔️	✔️	✔️
Long	Mantis Dual 5015 Toolhead	MGN12 Dual 5015 Toolhead for 2.4 & 1.8	❌	✔️	✔️	❌
Lukas	SSD1306 Case Front Cover	SSD1306 Mount replacement for Mini12864	❌	❌	✔️	❌	✔️
Mac10goesBRRRT	PiTFT Mount	Mount for the BTT PiTFT Touchscreen	❌	❔	✔️	❔	✔️
Majarspeed	Hartk board mount galileo	It hangs stuff on your tool	❌	❌	✔️	❌
MakeALeft	Switchwire Clean Center Grill	Removed magnet holders on center panel for cleaner look	❌	❌	❌	✔️	❌
madfabrications	Vertical PSU Mount	Mounts the PSU vertically on the DIN rails	❌	❌	✔️	❌
madros	V0 OLED-skirt	V0 skirt with 0.96" OLED	✔️	❌	❌	❌
MasturMynd	Stealth Zero	A low poly gantry with front tensioners and optional front mounted x rail	✔️	❌	❌	❌	❌
MathematicalPotato	V0.1 Belted Z Drive	Conversion to a belted Z axis for the V0.1 adapted from theFPVGeek's mod for the V0.0	✔️	❌	❌	❌
Maverick	MiniSB_Sharkfin	Modified MiniSB to use a Sharkfin Extruder	✔️	✔️	✔️	✔️	✔️
	MiniSB_Rapido	Modified MiniSB to use a Rapido hotend	✔️	✔️	✔️	✔️	✔️
	MiniSB_LGXL	A Bondtech LGX Lite variant of the MiniSB	✔️	✔️	✔️	✔️	✔️
	V0.2 Handles	Add handles to the extrusion tophat	✔️	❌	❌	❌
maximilian-foerg	Afterburner Turbo Mod	A purely cosmetic mod for Afterburner	❌	✔️	✔️	✔️	✔️
	Switchwire Double 60mm Fan Mount	A mount for two (or four) 60mm fans in SW's electronics compartment	❌	❌	❌	✔️	❌
MCKURT	Switchwire Y Belt Tensioner	Switchwie Y axis Belt Tensioner	❌	❌	❌	✔️	❌
MCMBen	Voron0 Block & Tackle Z Belt	A block & tackle belted Z solution using NEMA14. Ratios from 5:1 to 8:1 and friction prevent Z drop when powered off.	✔️	❌	❌	❌	❌
Mellow	V0 Fly-Gemini	Fly-Gemini adapted model for V0	✔️	❌	❌	❌	❌
mikepthomas	MKS Mosfet Mount	MKS Mosfet Mount based of the Trident Raspberry Pi Mount.	❌	✔️	✔️	❌	✔️
MikesMods	LGX mount for V0.1 with 2nd X rail	V0.1 mod for mounting Bondtech LGX extruder with addition of 2nd X rail on the back of the 1515 extrusion.	✔️	❌	❌	❌	❌
Minsekt	Rear Umbilical	Rear Umbilical mounting solution including a relocated Y-Endstop	❌	❔	✔️	❌	❌
mjoaris	10x11 Cable Chain Endcaps	Printable Endcaps for 10x11 Cable Chains	❌	✔️	✔️	❌
	Mini12864 LCD Mount	Swiveling case for the Fysetc Mini12864 LCD	❌	❔	✔️	❌
Mosher	Door hinges with M3 screws shafts	Simple mod of print in place door hinges, which uses m3 screws as shafts.	❌	❌	✔️	❌
mpfl	V0.1 OLED-skirt	V0.1 skirt with 0.96" OLED	✔️	❌	❌	❌
MrBean66	SKR Pro DIN Mount	Simple mod to mount the SKR Pro board from BTT to a DIN rails.	❌	✔️	✔️	❌
MrDespair	MiniAB Pinda Probe Mount	Replacement MiniAB Cowling to add a mount for a Pinda style probe.	✔️	❌	❌	❌	❌
Mrgl-Mrgl	LGX Lite Mount	a mount for the LGX Lite	❌	✔️	✔️	❌	✔️
MSA	Belt tension helper	Belt tension helper for V0.1	✔️	❌	❌	❌
MSiemons	Tophat Hinge V0	Simple hinge for V0 Tophat	✔️	❌	❌	❌
muradir	Zodiac BMO Stealthburner Toolhead	A Stealthburner toolhead for the Zodiac BMO Hotend, based on the Phaetus BMO toolhead.	❌	✔️	✔️	✔️	✔️
Nashuar	V0 Dragon Toolhead M2.5x8	This toolhead uses the stock M2.5 screw that came with the dragon hotend	✔️	❌	❌	❌
natewalck	V1.8 Jigs	Jigs for assembling V1.8	❌	✔️	❌	❌
nhchiu	V0.1 Movable Pulley Z Drive	A movable pulley system on the Z axis with 1:8 total speed ratio for V0.1	✔️	❌	❌	❌	❌
nikolasbabetas	Neopixel Holder	A holder to attach Neopixel/WS2812B Led Strips to the V0.1	✔️	❌	❌	❌	❌
Nomsplease	60mm Shaft Jig	Simple jig for cutting and grinding 60mm Z shafts	❌	❌	✔️	❌
	Duet Wifi Mount	Duet wifi mount in pocketwatch location	✔️	❌	❌	❌
	LED Mounts	Basic LED mounts for 10 and 12mm strips	✔️	❌	❌	❌
	Remixed Panel Mounts	Remixed rear bottom panel mounts with stop	✔️	❌	❌	❌
	Pi Cam/ZeroW Mount	Mount for pi camera and ZeroW	✔️	❌	❌	❌
	Pocket Watch Rear Reolcation Bracket	Pocket watch rear reolcation bracket	✔️	❌	❌	❌
Oakman	FYSETC Spider Metal DIN Mount	Use a metal DIN mount for your FYSETC Spider	❌	✔️	✔️	❌
	BTT 24V UPS Metal DIN Mount	Adapter to use a metal DIN mount for the BTT 24V UPS	❌	✔️	✔️	❌
	RPI Metal DIN Mount	Adapter for metal DIN mounting the Raspberry Pi	❌	✔️	✔️	❌
OboMaker3D	C17-EXT Filter HEPA Carbon	Replaces standard filter with new HEPA Crabon and 120mm fan V1.1	❌	❌	✔️	✔️	✔️
	C17-EXT-CARTRIDGE for C17-EXT filter	Alternative to a commercial cartridge for the C17-EXT filter	❌	❌	✔️	✔️	✔️
ommy	roller brackets	Brackets to help rolling V2 on its side.	❌	❌	✔️	❌
oxno	RBP Zero Bracket	Bracket for Raspberry pi zero.	❌	✔️	✔️	❔
padok	Chain Anchor - ADXL345 mount Mod	A ADXL345 mount for the Afterburner	❌	❔	✔️	❔
Phalanx	"Other" Idlers Mod	Allow usage of wider toolheads on the V2	❌	❔	✔️	❌
piet206	V1.8 Z Rails Mod	Add MGN12H linear rails for Z axis motion	❌	✔️	❌	❌
Polared	Power Inlet with Keystone Insert	Voron 0.1 Power inlet with keystone insert slot	✔️	❌	❌	❌	❌
prasadp4009	StealthBurner CR Touch Mod	Voron SW StealthBurner CR Touch Mod	❌	❌	❌	✔️	❌
Polar-Ted	V0.1 Two Piece Back Panel	Vented 2 piece back panel for V0	✔️	❌	❌	❌	❌
	V0.1 Z nozzle endstop switch	Sexbolt style switch for V0	✔️	❌	❌	❌	❌
Printopal	Magnetic top panel	Top panel with magnets allows for quick installation and removal	❌	✔️	✔️	❌
PsychoShaft	C92X_PsycHoShafts_Mount	2020 Top profile 920 camera mount / 2 point axis pivot	❔	✔️	✔️	❌	✔️
QuackProfit	V0 Adafruit NeoPixel LED Mounts	Mount Adafruit PCB NeoPixel Sticks on the V0 Y-rail extrusions	✔️	❌	❌	❌
quattroerik	V2.4 Door Hinge M3 3mm 180deg	Voron 2.4 door hinges for 3mm panel, 180 deg opening and m3 screw as shaft	❌	❌	✔️	❌	✔️
randell	Door Hinges	Door hinges that use an M3 bolt for a pin and bolts thru the panel	❌	❌	✔️	❌
	Microswitch Pod for PCB	Modified endstop pod for use of endstop switches mounted on a PCB	❌	❌	✔️	❌
raymondh	Large Spool Holders	Larger spool holders for KVP spools	❌	✔️	✔️	❌
reapola	MKS CANable Pro DIN Mount	MKS CANable Pro mount which mounts on a DIN rail	✔️	✔️	✔️	✔️	✔️
reQu1em00	Kirigami LED Bed Front	Kirigami bed front with space for a single LED or Neopixel button	✔️	❌	❌	❌	❌
revnull	Raspberry Pi 7inch Display Mount	An articulating mount for the offical Raspberry Pi 7inch touch screen	❔	❔	✔️	❔
Rhastlyn	Wansview 1080p Camera Mount	A camera mount that replaces the OEM part to allow the camera to be mounted to a 2020 extrusion	❌	❔	✔️	❌
	60mm Fan Cover	A easy to install cover for spec 60mm fans originally designed for a 2.4 build	❌	❔	✔️	❌
richardjm	ADXL drag chain mount	Permanent mount for ADXL boards on the back of the motor, replacing the drag chain mount.	❌	❌	✔️	❌	❔
	Back blanking plate	Back blanking plate that can be used instead of the exhaust filter housing if you are using something like a nevermore filter instead.	❌	❌	✔️	❌	❔
	LED 15.5mm quarter round mounts	Mounting corners with integrated cable runs for 15.5mm quarter round aluminium led extrusions.	❌	❌	✔️	❌	❔
	Printable snap latches for 2020 extrusion	Quick release panel latch inspired by the work of others.	❌	❔	✔️	❔	❔
	Picam corner mount	Out of the way corner mounted picam	❌	❌	✔️	❌	❔
roboticator24	Touchscreen for OctoDash	Mount a 4-inch LCD touchscreen to your V2.4 in place of the usual 12864 panel to allow you to run the amazing OctoDash touch UI	❌	❌	✔️	❌
RockNLol	RockNRoll	Rockers to roll the printer on its back for easier access to the electronics compartment	❌	❔	✔️	❌	❔
rngSplat	Printable Switchwire Deck Plate	Print a deck plate for Switchwire with debossed Voron logo	❌	❌	❌	✔️
rsheng118	BTT octopus DIN vertical mount	DIN vertical mount for Big Tech Tree Octopus board	❌	❌	✔️	❌
ryandam	Cable Management Duct	Zip tie mount intergrated cable duct to hide your cable	✔️	❔	❔	❔	❔
sammynorway	LGX stealthburner connector cover	Cable cover for LGX and stealthburner	❌	✔️	✔️	✔️	✔️
samwiseg0	Microfit 2x3 Skirt Connector (ADXL)	Mod for a Microfit 2x3 connector to be mounted in a skirt	❌	❌	✔️	❔	❔
	AB Plug (Microfit 1x4)	Mod to mount A & B motor connectors to the gantry	❌	❌	✔️	❌	❔
	LRS PSU Screw Terminal Cover	Mod to cover the screw terminals for several LRS style PSUs	✔️	✔️	✔️	✔️	✔️
	4 Channel Relay Under Deck Mount	Mod to mount a 4 channel GPIO controlled relay	❌	❌	✔️	❌	❔
	ESP8266 NodeMCU Din Mount	Din mount for ESP8266 NodeMCU	❌	❔	✔️	❌	✔️
	Corner Cable Hide/Cover (LED Wires)	Mod to hide cables around z idlers	❌	❌	✔️	❌	❌
	Extrusion/Chamber Thermistor Mount	Extrusion mount for a NTC100K Thermistor extrusion	✔️	✔️	✔️	✔️	✔️
	Corsair Flash Voyager GTX Din Mount	Din carrier for a Corsair Flash Voyager GTX	❌	❔	✔️	❌	✔️
scanlory	Clip-On Front Door Frame	Clip-on frame to stiffen and seal front door panels when using modified hinges.	❌	❌	✔️	❌	❌
ScramblerUSA	Side Skirt Power Switch	Skirt-mounted rocker switch for easy access for Voron 2.4	❌	❌	✔️	❌	❌
See1807	TopHat Exhaust and LED Light	A mount for 10mm LED strips and Exhaust for Voron V0	✔️	❌	❌	❌
Shiftingtech	Trident Dual Power Switch	A replacement skirt, allowing 2 power switches	❌	❌	❌	❌	✔️
ShinyPants	OrangePi 3 LTS DIN Rail bracket	A DIN rail mount for OrangePi LTS 3	❌	✔️	✔️	❌	✔️
Shteeeeeve	V0.1 LED Tophat	V0.1 LED Tophat w/ 24V LED Lightstrip	✔️	❌	❌	❌
Slidr	PanzerBalls 2.4	Squash Ball Feet for V2.4	❌	❌	✔️	❌	❌
	PanzerChain 2.4	Energychain for V2.4	❌	❌	✔️	❌	❌
slitte	PCB_Probe	PCB for BAT85 and pull up resistor	❌	❌	✔️	❌	✔️
	ssd_bracket	bracket for mounting a 2.5" ssd to a din rail	❌	❌	✔️	❌	✔️
sloscotty	Switchwire Wall Plate	SW plate for enclosure	❌	❌	❌	✔️
	NoNutz TopHat Cam Extension	Tophat extension with integrated webcam for V0/0.1	✔️	❌	❌	❌	❌
spacelab2021	Orbiter Clockwork Mount	A clockwork adaptor for the Orbiter v1.5 Extruder with full integration into the Afterburner. Includes a filament quick release lever for simple filament loading and unloading.	❌	✔️	✔️	✔️	✔️
Spaghetti-Bolognese	Simplified Z Drive Motor Mount	Z drive motor mount bracket mod to improve pulley to belt alignment	❌	❌	✔️	❌
	LCD Case Mod	Improvements to the V2.4 mini12864 LCD case inc E-stop button cover	❌	❌	✔️	❌
sse018	Octopus DIN Rail bracket	A Din rail mount for BTT Octopus board	❌	❌	✔️	❌
strayr	Creality toolhead for stealthburner	Use a creality ender 3 style hotend with stealthburner	❌	✔️	✔️	✔️	❌
sttts	Waveshare 5.5inch HDMI AMOLED Mount	Mod to mount a Waveshare 5.5inch full HD display on a V2	❌	❌	✔️	✔️
StvPtrsn	Skirts for a 320mm Build	Skirts for a 320mm build	❌	❌	✔️	❌
	Keystone Jack for Filtered Mains Panel	Add a keystone jack to your filtered mains plug panel	❌	❌	✔️	❌
	Side Fan Support, No Tape	Mount the 60mm side fans and inserts without tape	❌	❌	✔️	❌
	Parts_Jigs and Mods	Parts, Jigs and modifications I use for my builds	✔️	✔️	✔️	✔️	✔️
TAKUYA	WANSVIEW USB Camera Mount	WANSVIEW 1080p Camera Mount for Voron 2.4	❌	❌	✔️	❌
tallman5	Z Locks	Helping hands curing v2.4 build, replaces long zip ties.	❌	❌	✔️	❌	❌
tameike	Din Rail SKR 90 deg	SKR V1.3 bracket turned 90 degrees	❌	❔	✔️	❌
	Din Rail 2020 Holder	Attaching DIN Rails to 2020	❌	❔	✔️	❌
	TacoRaven Mounting Frame	TR V0 mount	✔️	❌	❌	❌
	Jetpack V0 base	Attach Jetpack to V0 frame	✔️	❌	❌	❌
tayto-chip	V2.4 Skirt Switch Mod	Add a ON/OFF Switch to side or front skirts	❌	❌	✔️	❌
teookie	AB dial indicator mount	Mount for attaching standard dial indicators to AB	❌	✔️	✔️	✔️
	SKR Brace	Rigidize and stabilize SKR 1.4 mounts	❌	❌	✔️	❌
th0mpy	BEEFY Din Clips	Two piece BEEFY Din Clips, holds stronger	❔	❔	✔️	❔	❔
TheSquiffy	V0 Belts holder	V0 Belts Holder	✔️	❌	❌	❌	❌
TiagoBarata	Logitech C270 Mount	Logitech C270 Top Center Mount	❌	❌	✔️	❌	❌
Tircown	Display mount 5"	Tiltable mount for a 5" tactile display	❌	❌	✔️	❌
	Raspberry in plug panel	Raspberry mount vertically in the plug panel, allow easy access to ports	❌	❌	✔️	❌
	DIN mount RS-15-5 PSU	A DIN mount for the RS-15-5	❔	❔	✔️	❔
	V0.1 Skirt buttons	Buttons for V0.1 spec skirts	✔️	❌	❌	❌	❌
togi	Exhaust housing side fitting	Moves the exhaust housing bowden fitting 90 degrees to allow the printer to stand closer to a wall	❌	❌	✔️	❌
top_gun_de	mount_for_umbilical	Umbilical guide that goes on the chain anchor	❌	❔	✔️	❌	❔
Triano	Ender 3 Pro or V2 to Switchwire Mod	Convesion of an Ender 3 Pro or V2 to a Switchwire	❌	❌	❌	✔️
UltraWaffles	Ender 3 to SW conversion	A conversion mod for the ender 3 to switchwire. Designed to allow for enclosure and uses original ender 3 motors and switches	❌	❌	❌	✔️
VinnyCordeiro	RGB LED grid for Stealthburner	A small RGB LED grid for Stealthburner's logo	❌	✔️	✔️	✔️	✔️
warriorofwire	Slenderfan for Afterburner	Lighter, quieter, smaller Afterburner	❌	❌	✔️	❌
Weaslus	Electronics Bay and Enclosure Seperator	Better enclose chamber and keep heat from electronics	✔️	❌	❌	❌
whoppingpochard	Extrusion Backers	Laser-cut metal pieces to counteract bimetallic frame warping	❌	❔	✔️	❌
Wile.e	Deck Panel Support Clips	Clips to help support lower deck panels to prevent (or fix) warping:	❔	✔️	✔️	❔
	Stealthburner + CW1 + PCB Cover	Low-poly for Stealthburner + CW1 + PCB installations:	❌	✔️	✔️	✔️	❔
wrez	V0 Alternate IEC 320 C14 Power Inlet Housing	Drop in replacement for alternate-source power inlet if spec inlet is back-ordered	✔️	❌	❌	❌
xbst_	PCB LED Holder	Very simple mount for some (?) PCB LED Bars	❌	✔️	✔️	❌
	DIN Mount Omron Relay	A simple DIN rail mount for the BOM Relay	❌	✔️	✔️	❌
	DIN Mount Pi 4x Relay Board	A simple DIN rail mount for the 4 channel relay board for Raspberry Pi	❌	✔️	✔️	❌
	DIN Mount Max31865	A simple DIN rail mount for the Adafruit (or SAME SIZE clone) MAX31865 PT100 Board.	❌	✔️	✔️	❌
	Car Hood Style Bed Hinge	A way of reaching electronics from the top by having a "car hood" style hinge for the heatbed, and rotated electronics mounts.	❌	❌	✔️	❌
	Flat V2.4 Skirts	Flat V2.4 Skirts so a panel without cutouts can be used	❌	❌	✔️	❌
	V2.4 Fanless Middle Skirt	A Fanless alternative middle side skirt	❌	❌	✔️	❌
	Duct Mount	100mm/4" ducting mount for ventilation. Also supports umbilical cord and has 3 orientations for bowden adapter.	❌	❌	✔️	❌
	V2.4 Skirt Buttons	Skirt mod for custom Gcode macro buttons	❌	❌	✔️	❌
	HOYMK SSR Mount	Mount for Chinese HOYMK SSR	✔️	❌	❌	❌
	ADXL345 V0 Mount	V0 Mount for a ADXL345 module	✔️	❌	❌	❌
	Easy Access Rear Panels	New rear panels designed to expose the extruder for easy filament swapping	✔️	❌	❌	❌
	Hat LED Mount	Top Hat LED module mount	✔️	❌	❌	❌
	ZipClip V0	Very simple ziptie mount for v0 1515 extrusions	✔️	❌	❌	❌
	Screwed Front Door Hinge	Mod to screw the front door panel (instead of VHB)	✔️	❌	❌	❌
	V0 Buttons & OLED Mount	Mod to mount custom Gcode macro buttons & Waveshare 1.3" OLED display	✔️	❌	❌	❌
	Mobius 4 (M4) V0 Mod	Mod to mount a M4 extruder to a Voron 0 where pocketwatch extruder mounts	✔️	❌	❌	❌
	V0 Electronics Cover	A printed cover for v0 electronics. Requires larger printer to print.	✔️	❌	❌	❌
	V0 PiCam Mount	A Raspberry Pi Camera Mount For V0	✔️	❌	❌	❌
	DuetZero	Pi Zero mount over a Duet2 for space saving	✔️	✔️	✔️	❌
Xceled	Single Panel Magnet Mount	Mount your front panel using only magnets	❌	❔	✔️	❌
Yenda	SW More Robust XZ Belt Paths	Small mods to belt routing components to ensure a better/more robust alignment	❌	❌	❌	✔️	❌
Yeri	V0 Magnetic Panels	Mount V0 panels with magnets, removes need for hinges and lets you easily detach sides for access	✔️	❌	❌	❌
	V1 3Z	3Z mod for V1	❌	✔️	❌	❌
Zen3D	V0 Handle	Voron0 Handle for 3mm panels	✔️	❌	❌	❌
	V0 MidPanel HexPattern	Voron0 MidPanel with Hex pattern and Wire cover	✔️	❌	❌	❌
	V0 Skirt set	SSR, PowerSwitch, Adxl, Nameplate and color change printing	✔️	❌	❌	❌	❌
	V0 1515 T-nut	M3 square and hex nuts for Voron0 1515 frame	✔️	❌	❌	❌
zruncho	V0 No-Drop Nuts	Voron0 nut inserts which auto-align (LDO frames only)	✔️	❌	❌	❌
ZZP8202	Pull-out electrical store	Voron 2.4 Pull-out electrical store（350mm only）	❌	❌	✔️	❌	❌