Configuration TAB not open after build!!! only the configuration tab!!!???

[jmcdrone]

I build myself a .hex file from omnibusF4V3 on visual code without any error. But on the inav configurator i could not open the configuration tab. All other tabs are normally working!! Is that a bug? Best Regards

[sensei-hacker]

Which version number did you build, and what did you change?

[jmcdrone]

I use the code from github and run the command make OMNIBUSF4V3 on visual code. I get a .hex file and flash to my omnibusf4 flight controller. I change the softserial from s6 to a led pad. It works but i have to use cli to activate softserial feature because the configuration tab doesn't open on inav configurator Em qui., 17 de out. de 2024 13:45, Sensei ***@***.***> escreveu:

…

Which version number did you build, and what did you change? — Reply to this email directly, view it on GitHub <#2212 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AQPXEKNDW2XQTQYAU7474H3Z37SSXAVCNFSM6AAAAABQD2XCQ2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDIMRQGAZDONJUGY> . You are receiving this because you authored the thread.Message ID: ***@***.***>

[jmcdrone]

I build the newest version Em qui., 17 de out. de 2024 14:16, juliano cortez ***@***.***> escreveu:

…

I use the code from github and run the command make OMNIBUSF4V3 on visual code. I get a .hex file and flash to my omnibusf4 flight controller. I change the softserial from s6 to a led pad. It works but i have to use cli to activate softserial feature because the configuration tab doesn't open on inav configurator Em qui., 17 de out. de 2024 13:45, Sensei ***@***.***> escreveu: > Which version number did you build, and what did you change? > > — > Reply to this email directly, view it on GitHub > <#2212 (comment)>, > or unsubscribe > <https://github.com/notifications/unsubscribe-auth/AQPXEKNDW2XQTQYAU7474H3Z37SSXAVCNFSM6AAAAABQD2XCQ2VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDIMRQGAZDONJUGY> > . > You are receiving this because you authored the thread.Message ID: > ***@***.***> >

[MrD-RC]

Are you using the configurator from master? It will not work with the 7.1.2 release configurator.

[jmcdrone]

Yes, I use master. Which one may I use then?

[sensei-hacker]

Yes, I use master. Which one may I use then?

Then you would need the master of Configurator, which may have bugs, because it's not release code.

You might be better off making your change to 7.1.2

Also if you haven't seen this document, we have alrerady provided targets with soft serial on three different choices of pins:
https://github.com/iNavFlight/inav/blob/master/docs/boards/Omnibus%20F4.md

[jmcdrone]

where could i found the master configurator or the 1.7.2 code ? the point is that i am using one servo there for i need change the code from myself.

[sensei-hacker]

where could i found the master configurator or the 1.7.2 code ? the point is that i am using one servo there for i need change the code from myself.

On GitHub, on the top left there's a drop down to choose between different branches and tags. Click on the tags section. Or if you clicked the git repo, do "git checkout 7.1.2"

[jmcdrone]

ok obrigado!