Replies: 4 comments
-
|
You wrote "my rx is wired to UART4". |
Beta Was this translation helpful? Give feedback.
-
|
Hello,
It may be connected to UART 4. The writing on the board is very small. Assuming it's connected to UART 2, it's still not recognizing the RX. Any suggestions?
…________________________________
From: Sensei ***@***.***>
Sent: Sunday, July 7, 2024 11:11 PM
To: iNavFlight/inav-configurator ***@***.***>
Cc: MBR595 ***@***.***>; Author ***@***.***>
Subject: Re: [iNavFlight/inav-configurator] MATEK F405 v1 (Issue #2141)
You wrote "my rx is wired to UART4".
Your screenshot shows it's configured for rx on UART2.
—
Reply to this email directly, view it on GitHub<#2141 (comment)>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/AEMX4UWZ45Q25PSW3LDZNSDZLH7OXAVCNFSM6AAAAABKPV4D46VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDEMJSHEYDAMBWGM>.
You are receiving this because you authored the thread.Message ID: ***@***.***>
|
Beta Was this translation helpful? Give feedback.
-
|
In your shoes, the first thing I would do is use some good lighting and take a close-up picture with my phone. Then zoom in on that pic to a) verify which user it is on and b) check for any stray wire strands, solder whiskers, etc. If it's not connected to the same uart that is configured, that would be the problem. So I would start there. |
Beta Was this translation helpful? Give feedback.
-
|
Good Afternoon,
I inspected the board again. The RX is plugged in to UART4 and the GPS is plugged into UART 2. What should I do?
…________________________________
From: Sensei ***@***.***>
Sent: Monday, July 8, 2024 1:30 PM
To: iNavFlight/inav-configurator ***@***.***>
Cc: MBR595 ***@***.***>; Author ***@***.***>
Subject: Re: [iNavFlight/inav-configurator] MATEK F405 v1 (Issue #2141)
In your shoes, the first thing I would do is use some good lighting and take a close-up picture with my phone. Then zoom in on that pic to a) verify which user it is on and b) check for any stray wire strands, solder whiskers, etc.
If it's not connected to the same uart that is configured, that would be the problem. So I would start there.
—
Reply to this email directly, view it on GitHub<#2141 (comment)>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/AEMX4UQAFSLEIJGIFHLYXFTZLLECZAVCNFSM6AAAAABKPV4D46VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDEMJUG44DEMZUGI>.
You are receiving this because you authored the thread.Message ID: ***@***.***>
|
Beta Was this translation helpful? Give feedback.
-
Hello,
I recently changed controllers. Currently using a FRSKY TARANIS X-LITE PRO with the TBS module and receiver. I'm using a Matke F405 V1 board and INAV Configurator 7.1.1. FW is 7.1.0 MATEKF450SE. My RX is wired to UART4 but it's not being recognized in the configurator when I turn it on, save and reboot. Any advice you can offer is greatly appreciated.
Beta Was this translation helpful? Give feedback.
All reactions