Possible new features

[jgauchia]

• GPX Parsing
• Waypoint save
• Various settings (lcd, compass, sleep...)

[Shreyashsatone]

Hello there I am Working with "ELECROW ESP32 Terminal–with ESP32 3.5 inch parallel 480×320 TFT capacitive touch RGB display(RGB by chip ILI9488)" whit bord in the requeriment Display need to use "FT6X36 " con you help gide how to integrate

[Shreyashsatone]

ok I will chack now for i2c touch pin and update you

[Shreyashsatone]

I did not see any i2c touch pin for ARDUINO_ESP32S3_DEV // MAKERFABS ESP32S3 too

/**

• @brief TOUCH I2C pin definition

*/
#ifdef ICENAV_BOARD
extern const uint8_t TCH_I2C_PORT = 0;
extern const uint8_t TCH_I2C_SDA = 38;
extern const uint8_t TCH_I2C_SCL = 39;
extern const uint8_t TCH_I2C_INT = 40;
#endif
#ifndef ICENAV_BOARD
extern const uint8_t TCH_I2C_PORT = 0;
extern const uint8_t TCH_I2C_SDA = 38;
extern const uint8_t TCH_I2C_SCL = 39;
extern const uint8_t TCH_I2C_INT = 40;
#endif

[jgauchia]

Under #ifndef ICENAV_BOARD

[jgauchia]

Hi!

Have you managed to get it working? I’m really interested in supporting multiple existing boards on the market and making my firmware compatible with them. The problem is that I don't have access to all of them.

That doesn’t help much.

[Shreyashsatone]

Hello sir,

I was able to find the log need help to find problem and solution for these

15:15:09.085 -> ESP-ROM:esp32s3-20210327
15:15:09.085 -> Build:Mar 27 2021
15:15:09.085 -> rst:0x1 (POWERON),boot:0xb (SPI_FAST_FLASH_BOOT)
15:15:09.085 -> SPIWP:0xee
15:15:09.085 -> mode:DIO, clock div:1
15:15:09.085 -> load:0x3fce3808,len:0x4bc
15:15:09.085 -> load:0x403c9700,len:0xbd8
15:15:09.085 -> load:0x403cc700,len:0x2a0c
15:15:09.085 -> entry 0x403c98d0
15:15:09.392 -> [ 310][V][WiFiServer.h:42] WiFiServer(): WiFiServer::WiFiServer(port=11000, ...)
15:15:09.392 -> E (328) esp_core_dump_flash: Core dump data check failed:
15:15:09.392 -> Calculated checksum='56c8009d'
15:15:09.392 -> Image checksum='ffffffff'
15:15:09.392 -> E (330) psram: PSRAM ID read error: 0x00ffffff, PSRAM chip not found or not supported, or wrong PSRAM line mode
15:15:09.428 -> [ 336][W][esp32-hal-psram.c:71] psramInit(): PSRAM init failed!
15:15:09.428 -> [ 372][V][esp32-hal-uart.c:330] uartBegin(): UART0 baud(115200) Mode(800001c) rxPin(44) txPin(43)
15:15:09.460 -> [ 381][V][esp32-hal-uart.c:416] uartBegin(): UART0 not installed. Starting installation
15:15:09.460 -> [ 390][V][esp32-hal-uart.c:463] uartBegin(): UART0 initialization done.
15:15:09.460 -> [ 398][I][esp32-hal-i2c.c:75] i2cInit(): Initialising I2C Master: sda=38 scl=39 freq=100000
15:15:09.491 -> [ 407][W][Wire.cpp:301] begin(): Bus already started in Master Mode.
15:15:09.491 -> [ 425][E][Wire.cpp:499] requestFrom(): i2cWriteReadNonStop returned Error -1
15:15:09.491 -> [ 432][E][compass.cpp:75] initCompass(): IMU initialization unsuccessful
15:15:09.491 -> [ 438][E][compass.cpp:76] initCompass(): Check IMU wiring or try cycling power
15:15:09.524 -> [ 446][E][compass.cpp:77] initCompass(): Status: -1
15:15:09.524 -> [ 451][I][EasyPreferences.cpp:28] init(): debug mode: enable
15:15:09.524 ->

15:15:09.524 -> [ 458][E][Preferences.cpp:503] getBytesLength(): nvs_get_blob len fail: C_offset_x NOT_FOUND
15:15:09.524 -> [ 466][E][Preferences.cpp:503] getBytesLength(): nvs_get_blob len fail: C_offset_y NOT_FOUND
15:15:09.558 -> [ 475][V][Preferences.cpp:352] getUChar(): nvs_get_u8 fail: Map_rot NOT_FOUND
15:15:09.558 -> [ 482][V][Preferences.cpp:400] getUInt(): nvs_get_u32 fail: Def_zoom NOT_FOUND
15:15:09.558 -> [ 489][V][Preferences.cpp:352] getUChar(): nvs_get_u8 fail: Map_compass NOT_FOUND
15:15:09.558 -> [ 497][V][Preferences.cpp:352] getUChar(): nvs_get_u8 fail: Compass_rot NOT_FOUND
15:15:09.558 -> [ 504][V][Preferences.cpp:352] getUChar(): nvs_get_u8 fail: Map_speed NOT_FOUND
15:15:09.589 -> [ 512][V][Preferences.cpp:352] getUChar(): nvs_get_u8 fail: Map_scale NOT_FOUND
15:15:09.589 -> [ 519][V][Preferences.cpp:364] getShort(): nvs_get_i16 fail: GPS_speed NOT_FOUND
15:15:09.589 -> [ 527][V][Preferences.cpp:364] getShort(): nvs_get_i16 fail: GPS_rate NOT_FOUND
15:15:09.589 -> [ 534][V][Preferences.cpp:388] getInt(): nvs_get_i32 fail: Compass_X NOT_FOUND
15:15:09.624 -> [ 541][V][Preferences.cpp:388] getInt(): nvs_get_i32 fail: Compass_Y NOT_FOUND
15:15:09.624 -> [ 548][V][Preferences.cpp:388] getInt(): nvs_get_i32 fail: Coords_X NOT_FOUND
15:15:09.624 -> [ 556][V][Preferences.cpp:388] getInt(): nvs_get_i32 fail: Coords_Y NOT_FOUND
15:15:09.624 -> [ 563][V][Preferences.cpp:388] getInt(): nvs_get_i32 fail: Altitude_X NOT_FOUND
15:15:09.624 -> [ 570][V][Preferences.cpp:388] getInt(): nvs_get_i32 fail: Altitude_Y NOT_FOUND
15:15:09.657 -> [ 577][V][Preferences.cpp:388] getInt(): nvs_get_i32 fail: Speed_X NOT_FOUND
15:15:09.657 -> [ 584][V][Preferences.cpp:388] getInt(): nvs_get_i32 fail: Speed_Y NOT_FOUND
15:15:09.657 -> [ 591][V][Preferences.cpp:352] getUChar(): nvs_get_u8 fail: Map_vector NOT_FOUND
15:15:09.657 -> [ 599][V][Preferences.cpp:352] getUChar(): nvs_get_u8 fail: Map_mode NOT_FOUND
15:15:09.689 -> [ 606][V][settings.cpp:281] printSettings(): KEYNAME DEFINED VALUE
15:15:09.689 -> [ 613][V][settings.cpp:282] printSettings(): ======= ======= =====
15:15:09.689 -> [ 620][V][settings.cpp:290] printSettings(): Map_rot default
15:15:09.689 -> [ 626][V][settings.cpp:290] printSettings(): Map_speed default
15:15:09.689 -> [ 633][V][settings.cpp:290] printSettings(): Map_scale default
15:15:09.721 -> [ 639][V][settings.cpp:290] printSettings(): Map_compass default
15:15:09.721 -> [ 646][V][settings.cpp:290] printSettings(): Map_vector default
15:15:09.721 -> [ 652][V][settings.cpp:290] printSettings(): Map_mode default
15:15:09.721 -> [ 659][V][settings.cpp:290] printSettings(): Compass_X default
15:15:09.721 -> [ 665][V][settings.cpp:290] printSettings(): Compass_Y default
15:15:09.753 -> [ 672][V][settings.cpp:290] printSettings(): Coords_X default
15:15:09.753 -> [ 678][V][settings.cpp:290] printSettings(): Coords_Y default
15:15:09.753 -> [ 685][V][settings.cpp:290] printSettings(): Altitude_X default
15:15:09.753 -> [ 691][V][settings.cpp:290] printSettings(): Altitude_Y default
15:15:09.753 -> [ 697][V][settings.cpp:290] printSettings(): Speed_X default
15:15:09.785 -> [ 704][V][settings.cpp:290] printSettings(): Speed_Y default
15:15:09.785 -> [ 710][V][settings.cpp:290] printSettings(): C_offset_x default
15:15:09.785 -> [ 717][V][settings.cpp:290] printSettings(): C_offset_y default
15:15:09.785 -> [ 723][V][settings.cpp:290] printSettings(): Compass_rot default
15:15:09.785 -> [ 730][V][settings.cpp:290] printSettings(): GPS_speed default
15:15:09.823 -> [ 736][V][settings.cpp:290] printSettings(): GPS_rate default
15:15:09.823 -> [ 743][V][settings.cpp:290] printSettings(): Def_zoom default
15:15:09.823 -> [ 757][V][storage.cpp:45] initSD(): SD Card Mounted
15:15:09.823 -> [ 762][I][storage.cpp:56] initSPIFFS(): Initializing SPIFFS
15:15:09.945 -> [ 868][I][storage.cpp:83] initSPIFFS(): Partition size: total: 1438481 used: 502
15:15:10.230 -> [ 1174][E][Wire.cpp:137] setPins(): bus already initialized. change pins only when not.
15:15:10.264 -> [ 1182][W][Wire.cpp:301] begin(): Bus already started in Master Mode.
15:15:10.264 -> [ 1190][V][Touch_FT5x06.cpp:63] _check_init(): [FT5x06] CIPHER:0x64 / FIRMID:0x01 / VENDID:0x11
15:15:10.336 -> [ 1249][E][tft.cpp:87] touchCalibrate(): Touch calibration doesn't exists

[jgauchia]

This log is normal if you don't have any preferences saved in NVS. in other words, independent of this logs , do you have any image on the TFT?

[Shreyashsatone]

thank you vary mush I will weith, I will also try to figer out.
also I have a Q. can it be because of the PSRAM MAKERFABS have 2M Elecrow have 8M.

[jgauchia]

No problem, code search for available PSRAM and adapt it, but it's possible that environment fails.

I'll check it

[jgauchia]

Please, can you send me an email? I'll Talk to you about your board

[Shreyashsatone]

please go through this "https://github.com/fbiego/windows-10-mobile-lvgl" I tried to copy environment from this and running icenav lvgl code but still failed. See if you can get it working.

[Shreyashsatone]

email Id:- kaisatone143@gmail.com

[jgauchia]

Hi,

Friday I'll receive an ELECROW ESP32 Terminal–with ESP32 3.5 board, when arrives I'll work on it to bring it support.

Please, be patient..

Thank you

[jgauchia]

Hi,

Today I've receive ELECROW board, this afternoon I'll try to modify my firmware I'll tell you when I'll finish