-
-
Notifications
You must be signed in to change notification settings - Fork 37
/
Copy pathmymacros.cfg
89 lines (65 loc) · 4.69 KB
/
mymacros.cfg
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
##### LH Stinger User Macro Configuration #####
[gcode_macro _CLIENT_VARIABLE]
##### Mainsail - Fluidd User Variables #####
variable_use_custom_pos : True ; use custom park coordinates for x,y [True/False]
variable_custom_park_x : 5 ; custom x position; value must be within your defined min and max of X
variable_custom_park_y : 200 ; custom y position; value must be within your defined min and max of Y
variable_custom_park_dz : 50 ; custom dz value; the value in mm to lift the nozzle when move to park position
variable_retract : 0.4 ; the value to retract while PAUSE
variable_cancel_retract : 0.4 ; the value to retract while CANCEL_PRINT
variable_speed_retract : 35.0 ; retract speed in mm/s
variable_unretract : 0.2 ; the value to unretract while RESUME
variable_speed_unretract : 35.0 ; unretract speed in mm/s
variable_speed_hop : 15.0 ; z move speed in mm/s
variable_speed_move : 140 ; move speed in mm/s
variable_park_at_cancel : False ; Keep False, this is handeled by PRINT_END - allow to move the toolhead to park while execute CANCEL_PRINT [True,False]
variable_use_fw_retract : False ; use fw_retraction instead of the manual version [True/False] - [firmware_retraction] must be defined in the printer.cfg if you set use_fw_retract: True
variable_idle_timeout : 0 ; time in sec until idle_timeout kicks in. Value 0 means that no value will be set or restored
##### LH Stinger User Variables #####
# System
variable_stop_bg_services : False # Stops host scheduled tasks during print to avoid high cpu/mem load
# Print
variable_accel_factor: 1.0 # Global Acceleration Factor (Scales the acceleration value set by the slicer) - can be adjusted during print with SET ACCEL FACTOR
variable_use_multi_bed_mesh_profiles: False # PRINT_START tries matching existing bed mesh profiles with set bet temperature. REQ Profiles: "default", "75", "105"
# Filament
variable_my_end_retract: 4 # mm - retract amount at the end of the print. This value is primed back at print start. - Set it very low or to 0 for MMU
variable_my_load_len: 65.0 # distance used for filament load
variable_my_load_prime_len: 75.0 # amount of priming/purging after the filament is loaded
variable_my_unload_len: 50.0 # distance used for filament unload
variable_my_purge_len: 50.0 # arbitrary amount
# Purge Line
variable_purge_x: 195 # X - Bed position to purge start the purge line
variable_purge_y: 42 # Y
variable_purge_z: 0.8 # Z
variable_purge_length: 20 # mm - length of the purge line
variable_purge_amount: 100 # mm of filament
# Velocity
variable_velocity_start: 300 # Velocity during PRINT_START in mm/s
variable_accel_start: 10000 # Acceleration during PRINT_START in mm2/s
# Positions
variable_nozzle_heat_x: 20 # X - Safe spot to heat up nozzle during PRINT START and PAUSE - M600 Filament Change
variable_nozzle_heat_y: 140 # Y - Bed center, avoiding to heat up the Y motor mounts
variable_nozzle_heat_z: 20 # Z
variable_change_z_min: 80 # Minimum Z height for PAUSE - M600 Filament Change
# Aux Fan
variable_has_aux_fan: True # Enable if using Aux fan. [fan_generic aux] has to be enabled in printer.cfg. Check example config.
variable_link_aux: True # Linking Aux fan speeds with Part fan
variable_aux_ratio: 1 # Ratio between Part fan and Aux when linked. 0.75 equals 75% of the Part fan speed
# Quiet Mode (Qmode) # To enable quiet mode, trigger the Qmode macro, or set QUIETMODE=1 in the slicer print start parameters
variable_q_fan_max: 50 # 0-100 % - All fan speeds are defined as percentages: 0-100 %
variable_q_fan_aux: 0 # Aux fan speed. Usually disabled in quiet mode
variable_q_link_aux: False # Link aux fan to part fan, or keep it independent to be able to be turned off
variable_q_feedrate: 100 # 0-100 % - Print speed percentage
variable_q_max_velocity: 200 # Caps max velocity
variable_q_max_accel: 10000 # Caps max accel
variable_q_accel_factor: 1.0 # Acceleration Multiplier - 0.5 = 50%
variable_q_min_cruise: 0.4 # Minimum distance to cruise
variable_q_scv: 5 # Max SCV
variable_q_stealthchop: False # Enable Stealthchop switching on TMC2240
# Advanced
variable_heat_range: 5 # C - Range in degrees to consider the nozzle or bed as heated up to avoid stalling during heat and wait commands
variable_version: 2.0 # Keeping track of version number between the settings file and the code file.
gcode:
##### Macros #####
[include mymacros_code.cfg] # Main codebase for the LH Stinger Macros
[include testspeed.cfg] # Speed testing macros tuned to push the limits on cartesian motion systems