{% if prerelease %}
{% endif %}
{% if installed %}
{% if (version_installed.split(".")[0] | int) < 1 %} {% if (version_installed.split(".")[1] | int) < 6 %}
- Unique id of entities changed. Using serial number now instead of cloud API id. Old entites are updated with new unique id.
- Removed sleep switch. {% if (version_installed.split(".")[1] | int) < 8 %}
- Removed application key from advanced settings page. Only application name is used for configuration.
- When migrating from version 0.6 or 0.7 new configuration may fail. Please remove and re-install integration. {% endif %}
- Added support for air conditioners (beta)
- Added periodic discovery of appliances.
- Added support for appliance address change.
- Enable integration configuration.
- Enable discovery of appliances at later time
- Select appliance discovery behavior via dropdown
- Add notification if appliance is discovered on the network, but was either ignored, or polled from the cloud
- Added tank removed (bucket) binary sensor
- Reverted to three presets for fan in all cases.
- If appliance doesn't load at start, integration will attempt again to set it up.
- An error during startup doesn't prevent integration to load.
- Fixed integration reload failing.
- Fixed entity naming conflicts after an appliance with same id as another old appliance is added.
{% endif %} {% endif %} {% endif %}
Adds support for Midea air conditioning and dehumidifier appliances via local network. Support for air conditioning devices is in beta
This component will set up the following entities for dehumidifiers.
| Platform | Description |
|---|---|
humidifier |
Dehumidifier entity. Depending on the model following modes are supported: Set, Continuos, Smart (if supported), Dry (if supported), Antimould (if supported), Purifier (if supported). |
fan |
Fan entity for controlling dehumidifier fan. Three preset modes are available: Low, Medium and High. |
binary_sensor |
Problem sensor indicating when tank is full. |
binary_sensor |
Problem sensor indicating when tank is removed (created if device announces that pump is supported). |
binary_sensor |
Problem sensor indicating when filter needs cleaning (created if device announces that filter is supported). |
binary_sensor |
Cold sensor indicating defrosting is active (disabled by default). |
sensor |
Sensors for current relative humidity measured by dehumidifier. |
sensor |
Sensor for current temperature measured by dehumidifier. |
sensor |
Sensor for water level in the tank (created if device announces that water level is supported). |
switch |
Switch ion mode on and off (created if device announces that (an)ion mode is supported). |
switch |
Switch pump on and off (created if device announces that pump is supported). |
switch |
Switch to enable pump (created if device announces that pump is supported). |
switch |
Switch to activate beep on action (disabled by default). |
In addition to this, humidifier entity will have additonal attributes describing capabilities, current and last error code, time of last error, as well as last payloads received.
This component will set up the following entities for air conditioners.
| Platform | Description |
|---|---|
climate |
Climate entity. |
sensor |
Sensor for outside temperature measured by air conditioner. |
switch |
Switch purifier mode on and off (enabled if device announces that it is supported). |
switch |
Switch dryer mode on and off (disabled by default). |
switch |
Switch to activate beep on action (disabled by default). |
switch |
Switch display to Fahrenheit degrees (enabled if device announces that it is supported). |
switch |
Switch turbo fan on and off (enabled if device announces that it is supported). |
switch |
Switch screen on and off (enabled if device announces that it is supported). |
In addition to this, climate entity will have additonal attributes describing capabilities, current and last error code, time of last error, as well as last payloads received.
{% if not installed %}
- Click Install.
- In the HA UI go to "Configuration" -> "Integrations" click "+" and search for "Midea Air Appliances (LAN)".
- If you want to use integration with air conditioner unit(s), please select the checkbox on "Advanced settings" page.
{% endif %}
- or search for "Midea Air Appliances (LAN)"
- Sign-in with Midea app account - you may choose Midea app that corresponds to one you use (anyone should work).
- On advanced options dialog you may enter another application key if you want, specify a network range to be used for discovery or choose to rely on cloud polling. If you don't specify network range, the integration will scan all local network interfaces. If you want to use custom component with an air conditioner unit, please select the appropriate checkbox.
- For devices that are known to cloud service, but not discovered locally, you will have another prompt to enter details if you know them or to specify that you want to rely on cloud polling for that device.
You may look at following Lovelace cards: