ZYYX Pro config on various MKS boards.

Marlin/Configuration_Robin_Nano_v12.h

@@ -0,0 +1,48 @@
+
+#pragma once
+
+#define MOTHERBOARD BOARD_MKS_ROBIN_NANO
+
+/**
+ * Select the serial port on the board to use for communication with the host.
+ * This allows the connection of wireless adapters (for instance) to non-default port pins.
+ * Serial port -1 is the USB emulated serial port, if available.
+ * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader.
+ *
+ * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
+ */
+#define SERIAL_PORT 3
+
+/**
+ * Select a secondary serial port on the board to use for communication with the host.
+ * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
+ */
+#define SERIAL_PORT_2 -1
+
+// @section homing
+
+/**
+ * Stepper Drivers
+ *
+ * These settings allow Marlin to tune stepper driver timing and enable advanced options for
+ * stepper drivers that support them. You may also override timing options in Configuration_adv.h.
+ *
+ * A4988 is assumed for unspecified drivers.
+ *
+ * Options: A4988, A5984, DRV8825, LV8729, L6470, L6474, POWERSTEP01,
+ *          TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2160, TMC2160_STANDALONE,
+ *          TMC2208, TMC2208_STANDALONE, TMC2209, TMC2209_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE
+ * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'L6474', 'POWERSTEP01', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
+ */
+#define X_DRIVER_TYPE  TMC2209_STANDALONE
+#define Y_DRIVER_TYPE  TMC2209_STANDALONE
+#define Z_DRIVER_TYPE  TMC2209_STANDALONE
+#define E0_DRIVER_TYPE TMC2209_STANDALONE
+
+// @section lcd
+
+#define MKS_ROBIN_TFT35
+#define TOUCH_SCREEN

Marlin/Configuration_Robin_Nano_v2.h

@@ -0,0 +1,48 @@
+
+#pragma once
+
+#define MOTHERBOARD BOARD_MKS_ROBIN_NANO_V2
+
+/**
+ * Select the serial port on the board to use for communication with the host.
+ * This allows the connection of wireless adapters (for instance) to non-default port pins.
+ * Serial port -1 is the USB emulated serial port, if available.
+ * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader.
+ *
+ * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
+ */
+#define SERIAL_PORT 1
+
+/**
+ * Select a secondary serial port on the board to use for communication with the host.
+ * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
+ */
+#define SERIAL_PORT_2 3
+
+// @section homing
+
+/**
+ * Stepper Drivers
+ *
+ * These settings allow Marlin to tune stepper driver timing and enable advanced options for
+ * stepper drivers that support them. You may also override timing options in Configuration_adv.h.
+ *
+ * A4988 is assumed for unspecified drivers.
+ *
+ * Options: A4988, A5984, DRV8825, LV8729, L6470, L6474, POWERSTEP01,
+ *          TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2160, TMC2160_STANDALONE,
+ *          TMC2208, TMC2208_STANDALONE, TMC2209, TMC2209_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE
+ * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'L6474', 'POWERSTEP01', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
+ */
+#define X_DRIVER_TYPE  TMC2209
+#define Y_DRIVER_TYPE  TMC2209
+#define Z_DRIVER_TYPE  TMC2209
+#define E0_DRIVER_TYPE TMC2209
+
+// @section lcd
+
+#define MKS_TS35_V2_0
+#define TOUCH_SCREEN

Marlin/Configuration_SGEN_L_v1.h

@@ -0,0 +1,50 @@
+
+#pragma once
+
+#define MOTHERBOARD BOARD_MKS_SGEN_L
+
+/**
+ * Select the serial port on the board to use for communication with the host.
+ * This allows the connection of wireless adapters (for instance) to non-default port pins.
+ * Serial port -1 is the USB emulated serial port, if available.
+ * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader.
+ *
+ * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
+ */
+#define SERIAL_PORT -1
+
+/**
+ * Select a secondary serial port on the board to use for communication with the host.
+ * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
+ */
+#define SERIAL_PORT_2 0
+
+// @section homing
+
+/**
+ * Stepper Drivers
+ *
+ * These settings allow Marlin to tune stepper driver timing and enable advanced options for
+ * stepper drivers that support them. You may also override timing options in Configuration_adv.h.
+ *
+ * A4988 is assumed for unspecified drivers.
+ *
+ * Options: A4988, A5984, DRV8825, LV8729, L6470, L6474, POWERSTEP01,
+ *          TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2160, TMC2160_STANDALONE,
+ *          TMC2208, TMC2208_STANDALONE, TMC2209, TMC2209_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE
+ * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'L6474', 'POWERSTEP01', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
+ */
+#define X_DRIVER_TYPE  TMC2209
+#define Y_DRIVER_TYPE  TMC2209
+#define Z_DRIVER_TYPE  TMC2209
+#define E0_DRIVER_TYPE TMC2209
+
+// @section lcd
+
+#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
+
+// X Min
+#define FIL_RUNOUT_PIN P1_28

Marlin/Configuration_SGEN_L_v2.h

@@ -0,0 +1,50 @@
+
+#pragma once
+
+#define MOTHERBOARD BOARD_MKS_SGEN_L_V2
+
+/**
+ * Select the serial port on the board to use for communication with the host.
+ * This allows the connection of wireless adapters (for instance) to non-default port pins.
+ * Serial port -1 is the USB emulated serial port, if available.
+ * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader.
+ *
+ * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
+ */
+#define SERIAL_PORT -1
+
+/**
+ * Select a secondary serial port on the board to use for communication with the host.
+ * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
+ */
+#define SERIAL_PORT_2 0
+
+// @section homing
+
+/**
+ * Stepper Drivers
+ *
+ * These settings allow Marlin to tune stepper driver timing and enable advanced options for
+ * stepper drivers that support them. You may also override timing options in Configuration_adv.h.
+ *
+ * A4988 is assumed for unspecified drivers.
+ *
+ * Options: A4988, A5984, DRV8825, LV8729, L6470, L6474, POWERSTEP01,
+ *          TB6560, TB6600, TMC2100,
+ *          TMC2130, TMC2130_STANDALONE, TMC2160, TMC2160_STANDALONE,
+ *          TMC2208, TMC2208_STANDALONE, TMC2209, TMC2209_STANDALONE,
+ *          TMC26X,  TMC26X_STANDALONE,  TMC2660, TMC2660_STANDALONE,
+ *          TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE
+ * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'L6474', 'POWERSTEP01', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
+ */
+#define X_DRIVER_TYPE  TMC2209
+#define Y_DRIVER_TYPE  TMC2209
+#define Z_DRIVER_TYPE  TMC2209
+#define E0_DRIVER_TYPE TMC2209
+
+// @section lcd
+
+#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
+
+// X Min
+#define FIL_RUNOUT_PIN P1_29

Marlin/Configuration_ZYYX_Pro.h

@@ -0,0 +1,67 @@
+
+// @section machine
+
+// The size of the print bed
+#define X_BED_SIZE 260
+#define Y_BED_SIZE 225
+
+#define Z_MAX_POS 200
+
+// Name displayed in the LCD "Ready" message and Info menu
+#define CUSTOM_MACHINE_NAME "ZYYX Pro"
+
+// @section probes
+
+/**
+ * Nozzle-to-Probe offsets { X, Y, Z }
+ *
+ * - Use a caliper or ruler to measure the distance from the tip of
+ *   the Nozzle to the center-point of the Probe in the X and Y axes.
+ * - For the Z offset use your best known value and adjust at runtime.
+ * - Probe Offsets can be tuned at runtime with 'M851', LCD menus, babystepping, etc.
+ *
+ * Assuming the typical work area orientation:
+ *  - Probe to RIGHT of the Nozzle has a Positive X offset
+ *  - Probe to LEFT  of the Nozzle has a Negative X offset
+ *  - Probe in BACK  of the Nozzle has a Positive Y offset
+ *  - Probe in FRONT of the Nozzle has a Negative Y offset
+ *
+ * Some examples:
+ *   #define NOZZLE_TO_PROBE_OFFSET { 10, 10, -1 }   // Example "1"
+ *   #define NOZZLE_TO_PROBE_OFFSET {-10,  5, -1 }   // Example "2"
+ *   #define NOZZLE_TO_PROBE_OFFSET {  5, -5, -1 }   // Example "3"
+ *   #define NOZZLE_TO_PROBE_OFFSET {-15,-10, -1 }   // Example "4"
+ *
+ *     +-- BACK ---+
+ *     |    [+]    |
+ *   L |        1  | R <-- Example "1" (right+,  back+)
+ *   E |  2        | I <-- Example "2" ( left-,  back+)
+ *   F |[-]  N  [+]| G <-- Nozzle
+ *   T |       3   | H <-- Example "3" (right+, front-)
+ *     | 4         | T <-- Example "4" ( left-, front-)
+ *     |    [-]    |
+ *     O-- FRONT --+
+ */
+#define NOZZLE_TO_PROBE_OFFSET { -30, 0, 3 }
+
+// Probe is 30 mm to the left of nozzle
+#define Z_SAFE_HOMING_X_POINT (X_MAX_POS - 30)  // X point for Z homing
+#define Z_SAFE_HOMING_Y_POINT Y_MAX_POS  // Y point for Z homing
+
+// @section extras
+
+// Define positions for probing points, use the hotend as reference not the sensor.
+#define TRAMMING_POINT_XY { {  248-30, 214 }, { 82-30,  214 }, { 166-30, 17 } }
+
+// @section leveling
+
+/**
+ * Points to probe for all 3-point Leveling procedures.
+ * Override if the automatically selected points are inadequate.
+ */
+#define PROBE_PT_1_X (X_MAX_POS - 30)
+#define PROBE_PT_1_Y Y_MAX_POS
+#define PROBE_PT_2_X (78 - 30)
+#define PROBE_PT_2_Y Y_MAX_POS
+#define PROBE_PT_3_X (X_MAX_POS - 30)
+#define PROBE_PT_3_Y Y_MIN_POS