-
Notifications
You must be signed in to change notification settings - Fork 51
/
README.txt
91 lines (72 loc) · 2.93 KB
/
README.txt
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
Pic32prog is a utility for loading data into a flash memory of Microchip PIC32
microcontrollers. Supported adapters and bootloaders:
* Microchip PICkit2
* Microchip PICkit3 with scripting firmware
* Olimex ARM-USB-Tiny (not finished yet)
* Olimex ARM-USB-Tiny, ARM-USB-Tiny-H and ARM-USB-OCH-H JTAG adapters
* Olimex MIPS-USB-OCH-H JTAG adapter
* Bus Blaster v2 JTAG adapter from Dangerous Prototypes
* Flyswatter JTAG adapter from TinCanTools
* AN1388 HID bootloader
* Legacy FS_USB HID bootloader
=== Usage ===
When called without parameters, pic32prog utility detects a type of microcontroller
and device configuration. For example:
% pic32prog
Programmer for Microchip PIC32 microcontrollers, Version 1.0
Copyright: (C) 2011 Serge Vakulenko
Adapter: PICkit2 Version 2.32.0
Processor: 795F512L (id 04307053)
Flash memory: 512 kbytes
Configuration:
DEVCFG0 = 7ffffffd
1 Debugger enabled
8 Use PGC2/PGD2
DEVCFG1 = ff6afd5b
3 Primary oscillator with PLL
1 Primary oscillator: XT
4 CLKO output active
3 Peripheral bus clock: SYSCLK / 8
4 Fail-safe clock monitor disable
8 Clock switching disable
a Watchdog postscale: 1/1024
DEVCFG2 = fff8f9d9
1 PLL divider: 1/2
5 PLL multiplier: 20x
1 USB PLL divider: 1/2
8 Disable USB PLL
Enable USB PLL
0 PLL postscaler: 1/1
DEVCFG3 = 3affffff
7 Assign irq priority 7 to shadow set
Ethernet RMII enabled
2 Default Ethernet i/o pins
Alternate CAN i/o pins
USBID pin: controlled by port
VBuson pin: controlled by port
Writing to flash memory:
pic32prog [-v] file.srec
pic32prog [-v] file.hex
Reading memory to file:
pic32prog -r file.bin address length
Parameters:
file.srec - file with firmware in SREC format
file.srec - file with firmware in Intel HEX format
file.bin - binary file
address - address in memory
-v - verify only (no write)
-r - read mode
Input file should have format SREC or Intel HEX.
You can convert ELF format (also COFF or A.OUT) to SREC using objcopy utility,
for example:
objcopy -O srec firmware.elf firmware.srec
=== Sources ===
Sources are distributed under the terms of GPL.
You can download sources using Git:
git clone https://github.com/sergev/pic32prog.git
To build it on Ubuntu, a few additional packages need
to be installed:
sudo apt-get install libusb-dev libusb-1.0-0-dev libudev-dev
___
Regards,
Serge Vakulenko