You signed in with another tab or window. Reload to refresh your session.You signed out in another tab or window. Reload to refresh your session.You switched accounts on another tab or window. Reload to refresh your session.Dismiss alert
I'm trying to program a new ESP8266 NodeMCU ESP-12E board for this project. I'm using VS Code with PlatformIO. I'm able to successfully run the example "blink" program. I am able to install this project successfully, however the board does not present any wifi or console output after reset.
Here's the logs from "upload and monitor", and you can see the console output at the end:
The terminal process "C:\Users\UserName.platformio\penv\Scripts\platformio.exe 'run', '--target', 'upload', '--target', 'monitor', '--environment', 'nodemcuv2'" terminated with exit code: 1.
Terminal will be reused by tasks, press any key to close it.
Executing task in folder esp8266_milight_hub: C:\Users\UserName.platformio\penv\Scripts\platformio.exe run --target upload --target monitor --environment nodemcuv2
toolchain-xtensa @ 2.100300.210717 (10.3.0)
LDF: Library Dependency Finder -> https://bit.ly/configure-pio-ldf
LDF Modes: Finder ~ chain, Compatibility ~ soft
Found 35 compatible libraries
Scanning dependencies...
No dependencies
Building in release mode
Retrieving maximum program size .pio\build\nodemcuv2\firmware.elf
Checking size .pio\build\nodemcuv2\firmware.elf
Advanced Memory Usage is available via "PlatformIO Home > Project Inspect"
RAM: [=== ] 34.0% (used 27892 bytes from 81920 bytes)
Flash: [== ] 24.9% (used 260093 bytes from 1044464 bytes)
Configuring upload protocol...
AVAILABLE: espota, esptool
CURRENT: upload_protocol = esptool
Looking for upload port...
Auto-detected: COM4
Uploading .pio\build\nodemcuv2\firmware.bin
esptool.py v3.0
Serial port COM4
Connecting....
Chip is ESP8266EX
Features: WiFi
Crystal is 26MHz
MAC: c8:c9:a3:5c:94:bb
Uploading stub...
Running stub...
Stub running...
Configuring flash size...
Compressed 264240 bytes to 194515...
Writing at 0x00000000... (8 %)
Writing at 0x00004000... (16 %)
Writing at 0x00008000... (25 %)
Writing at 0x0000c000... (33 %)
Writing at 0x00010000... (41 %)
Writing at 0x00014000... (50 %)
Writing at 0x00018000... (58 %)
Writing at 0x0001c000... (66 %)
Writing at 0x00020000... (75 %)
Writing at 0x00024000... (83 %)
Writing at 0x00028000... (91 %)
Writing at 0x0002c000... (100 %)
Wrote 264240 bytes (194515 compressed) at 0x00000000 in 17.2 seconds (effective 123.0 kbit/s)...
Hash of data verified.
Leaving...
Hard resetting via RTS pin...
====================================================================================================================== [SUCCESS] Took 20.49 seconds ======================================================================================================================--- Terminal on COM4 | 74880 8-N-1
--- Available filters and text transformations: colorize, debug, default, direct, esp8266_exception_decoder, hexlify, log2file, nocontrol, printable, send_on_enter, time
--- More details at https://bit.ly/pio-monitor-filters
--- Quit: Ctrl+C | Menu: Ctrl+T | Help: Ctrl+T followed by Ctrl+H
I'm trying to program a new ESP8266 NodeMCU ESP-12E board for this project. I'm using VS Code with PlatformIO. I'm able to successfully run the example "blink" program. I am able to install this project successfully, however the board does not present any wifi or console output after reset.
Here's the logs from "upload and monitor", and you can see the console output at the end:
Here's a link to the board I purchased if that matters:
https://smile.amazon.com/gp/product/B010N1SPRK/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
Any ideas? I'm really stuck here!
The text was updated successfully, but these errors were encountered: