Skip to content

Latest commit

 

History

History
131 lines (112 loc) · 3.5 KB

README.md

File metadata and controls

131 lines (112 loc) · 3.5 KB

dupont

Creates VXLAN tunnels over wireguard

Why ?

Wireguard does not allow you to route arbitrary traffic through a tunnel, let's say I have this setup

  • Network A: 10.0.0.0/24
  • Network B: 10.1.0.0/24
  • Tunnel A<>B 10.3.0.0/24

You cannot make A and B communicate without having to NAT traffic, hence masking the original IPs.

To get around this you can create an overlay network on top of the wireguard tunnel.

How ?

Look at the config files in the examples directory

Then compile the binary

$ make
$ ./bin/dupont -what apply -config examples/host-1.hcl
# You can teardown the config by doing
$ ./bin/dupont -what delete -config examples/host-1.hcl

Example config

You can write the configurations both in yaml and HCL, the HCL being the more readable one, as follows:

# Make sure we enable ip forward and co
ensureSysctl = true

# Our interfaces definitions
interfaces {
  # Wireguard interfaces definitions
  wireguard "wg-0" {
    # First interface definition
    address = "192.168.69.1/32"
    port    = 6969
    key {
      privateKey = "4CQWNQylWDWoZGgWDj58skAQuC84v1JXBKKqLTwcb3c="
      # Note that specifying the public key here is a matter
      # of convenience, you would not have that (prolly) on
      # an actual deployment
      publicKey = "bScGfgslFnmIEcuAdU8PQla6OtE29VntPOd3rOb5phs="
    }
    peer "wg-0" {
      description = "Laptop"
      key {
        publicKey = "NYNj4shJcxucrhgNTwRg1sshlCT9cGKvClWEsycm/28="
      }
      allowedIPs = [
        "192.168.69.2/32",
      ]
      endpoint {
        address = "10.99.1.200"
        port    = 6969
      }
      keepAlive = 5
    }
  }
  vxlan "vx-0" {
    address = "192.168.70.1/24"
    vni     = 60
    parent  = "wg-0"
    neighbour {
      address = "192.168.70.2"
    }
  }
}

Which produces something like that:

$ ip address
[...]
40: wg-0: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1420 qdisc noqueue state UNKNOWN group default 
    link/none 
    inet 192.168.69.2/24 brd 192.168.69.255 scope global wg-0
       valid_lft forever preferred_lft forever
41: br-vx-0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1350 qdisc noqueue state UP group default 
    link/ether 8a:a5:6a:ec:81:e5 brd ff:ff:ff:ff:ff:ff
    inet 192.168.70.2/24 brd 192.168.70.255 scope global br-vx-0
       valid_lft forever preferred_lft forever
    inet6 fe80::88a5:6aff:feec:81e5/64 scope link 
       valid_lft forever preferred_lft forever
42: vx-0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1350 qdisc noqueue master br-vx-0 state UNKNOWN group default 
    link/ether 8a:a5:6a:ec:81:e5 brd ff:ff:ff:ff:ff:ff
    inet6 fe80::88a5:6aff:feec:81e5/64 scope link 
       valid_lft forever preferred_lft forever

Topologies

You can also use dupont to generate the topology of the network for you. Create a file like so

name = "example topology"

network {
    wireguard     = "10.80.0.1/24"
    overlay       = "10.80.1.1/24"
    vni           = 42
    wireguardPort = 6060
}

hosts = {
    pi1 = "19.99.1.60"
    pi2 = "19.99.1.61"
    pi3 = "19.99.1.62"
    pi4 = "19.99.1.63"
}

Then run ./bin/dupont -what generate -config config/topology.hcl and it will generate one file per host in a folder named after the topology ID of the said topology. It is basically a short hash of the topology name. You would have then something like

$ tree 657861/
657861/
├── pi1.hcl
├── pi2.hcl
├── pi3.hcl
└── pi4.hcl

0 directories, 4 files

You only have to copy those files on every host of the mesh, then apply the config and you are done !