Changing monitoring state from "Offline" to "Opening serial connection"
Connecting to port /dev/ttyUSB0, baudrate 250000
Changing monitoring state from "Opening serial connection" to "Connecting"
Connected to: Serial<id=0x6805c990, open=True>(port='/dev/ttyUSB0', baudrate=250000, bytesize=8, parity='N', stopbits=1, timeout=10.0, xonxoff=False, rtscts=False, dsrdtr=False), starting monitor
Send: N0 M110 N0*125
Recv: ok N0 P15 B15
Send: N0 M110 N0*125
Changing monitoring state from "Connecting" to "Operational"
Recv: ok N0 P15 B15
Send: N0 M110 N0*125
Recv: ok N0 P15 B15
Send: N1 M115*39
Recv: FIRMWARE_NAME:Marlin 2.1.3 MRiscoC Ender3-427-BLTUBL-CR10DSPLY, based on bugfix-2.1.x (Jan  6 2025 20:23:28) SOURCE_CODE_URL:github.com/mriscoc/Ender3V2S1 PROTOCOL_VERSION:1.0 MACHINE_TYPE:Ender3-427-BLTUBL-CR10DSPLY KINEMATICS:Cartesian EXTRUDER_COUNT:1 UUID:cede2a2f-41a2-4748-9b12-c55c62f367ff
Recv: Cap:SERIAL_XON_XOFF:0
Recv: Cap:BINARY_FILE_TRANSFER:0
Recv: Cap:EEPROM:1
Recv: Cap:VOLUMETRIC:1
Recv: Cap:AUTOREPORT_POS:0
Recv: Cap:AUTOREPORT_TEMP:1
Recv: Cap:PROGRESS:0
Recv: Cap:PRINT_JOB:1
Recv: Cap:AUTOLEVEL:1
Recv: Cap:RUNOUT:1
Recv: Cap:Z_PROBE:1
Recv: Cap:LEVELING_DATA:1
Recv: Cap:BUILD_PERCENT:1
Recv: Cap:SOFTWARE_POWER:0
Recv: Cap:TOGGLE_LIGHTS:0
Recv: Cap:CASE_LIGHT_BRIGHTNESS:0
Recv: Cap:EMERGENCY_PARSER:1
Recv: Cap:HOST_ACTION_COMMANDS:1
Recv: Cap:PROMPT_SUPPORT:1
Recv: Cap:SDCARD:1
Recv: Cap:MULTI_VOLUME:0
Recv: Cap:REPEAT:0
Recv: Cap:SD_WRITE:0
Recv: Cap:AUTOREPORT_SD_STATUS:0
Recv: Cap:LONG_FILENAME:0
Recv: Cap:LFN_WRITE:0
Recv: Cap:CUSTOM_FIRMWARE_UPLOAD:0
Recv: Cap:EXTENDED_M20:0
Recv: Cap:THERMAL_PROTECTION:1
Recv: Cap:MOTION_MODES:0
Recv: Cap:ARCS:1
Recv: Cap:BABYSTEPPING:1
Recv: Cap:EP_BABYSTEP:0
Recv: Cap:CHAMBER_TEMPERATURE:0
Recv: Cap:COOLER_TEMPERATURE:0
Recv: Cap:MEATPACK:0
Recv: Cap:CONFIG_EXPORT:0
Recv: Cap:PROUI_AML:1
Recv: area:{full:{min:{x:0.00,y:0.00,z:0.00},max:{x:248.00,y:231.00,z:250.00}},work:{min:{x:0.00,y:0.00,z:0.00},max:{x:230.00,y:230.00,z:250.00}}}
Recv: ok N1 P15 B15
Send: M21
Recv: echo:SD card ok
Recv: ok P15 B15
Send: M155 S2
Recv:  T:19.87 /0.00 B:19.84 /0.00 @:0 B@:0
Recv: ok P15 B15
Send: M876 P1
Recv: ok P15 B15
Send: M20
Recv: Begin file list
Recv: FF_BED~1.GCO 80389
Recv: FLOWRA~1.GCO 155746
Recv: 3DBENC~2.GCO 1731020
Recv: LOADMY~1.GCO 1759
Recv: CHARIZ~1.GCO 1734637
Recv: 3DBENC~1.GCO 1731065
Recv: FF_BED~2.GCO 80434
Recv: FLOWRA~2.GCO 155791
Recv: PHONE_~1.GCO 128767
Recv: CALIFL~1.GCO 1002628
Recv: CALIFL~2.GCO 989694
Recv: HOODED~1.GCO 1993733
Recv: ELF_AR~1.GCO 1623439
Recv: STATUE~1.GCO 2115935
Recv: JAMES_~2.GCO 2115935
Recv: BED60~1.GCO 2115935
Recv: D20_19~1.GCO 892521
Recv: PIN5B9~1.GCO 402957
Recv: PIN5B9~2.GCO 438242
Recv: PIN5B9~3.GCO 1645024
Recv: End file list
Recv: ok P15 B15
Send: M20
Recv: Begin file list
Recv: FF_BED~1.GCO 80389
Recv: FLOWRA~1.GCO 155746
Recv: 3DBENC~2.GCO 1731020
Recv: LOADMY~1.GCO 1759
Recv: CHARIZ~1.GCO 1734637
Recv: 3DBENC~1.GCO 1731065
Recv: FF_BED~2.GCO 80434
Recv: FLOWRA~2.GCO 155791
Recv: PHONE_~1.GCO 128767
Recv: CALIFL~1.GCO 1002628
Recv: CALIFL~2.GCO 989694
Recv: HOODED~1.GCO 1993733
Recv: ELF_AR~1.GCO 1623439
Recv: STATUE~1.GCO 2115935
Recv: JAMES_~2.GCO 2115935
Recv: BED60~1.GCO 2115935
Recv: D20_19~1.GCO 892521
Recv: PIN5B9~1.GCO 402957
Recv: PIN5B9~2.GCO 438242
Recv: PIN5B9~3.GCO 1645024
Recv: End file list
Recv: ok P15 B15
Recv:  T:19.85 /0.00 B:19.77 /0.00 @:0 B@:0
Send: M503
Recv: echo:; Linear Units:
Recv: echo:  G21 ; (mm)
Recv: echo:; Temperature Units:
Recv: echo:  M149 C ; Units in Celsius
Recv: echo:; Filament settings (Disabled):
Recv: echo:  M200 S0 D1.75
Recv: echo:; Steps per unit:
Recv: echo:  M92 X80.00 Y80.00 Z400.00 E93.00
Recv: echo:; Max feedrates (units/s):
Recv: echo:  M203 X500.00 Y500.00 Z10.00 E45.00
Recv: echo:; Max Acceleration (units/s2):
Recv: echo:  M201 X500.00 Y500.00 Z100.00 E1000.00
Recv: echo:; Acceleration (units/s2) (P<print-accel> R<retract-accel> T<travel-accel>):
Recv: echo:  M204 P500.00 R800.00 T1000.00
Recv: echo:; Advanced (B<min_segment_time_us> S<min_feedrate> T<min_travel_feedrate> X<max_jerk> Y<max_jerk> Z<max_jerk> E<max_jerk>):
Recv: echo:  M205 B20000.00 S0.00 T0.00 X8.00 Y8.00 Z0.40 E5.00
Recv: echo:; Unified Bed Leveling:
Recv: echo:  M420 S0 Z10.00 ; Leveling OFF
Recv: 
Recv: Unified Bed Leveling System v1.01 inactive
Recv: echo:Active Mesh Slot 0
Recv: echo:EEPROM can hold 7 meshes.
Recv: 
Recv: echo:; Material heatup parameters:
Recv: echo:  M145 S0 H195.00 B60.00 F128
Recv: echo:  M145 S1 H240.00 B90.00 F128
Recv: echo:  M145 S2 H230.00 B80.00 F128
Recv: echo:  M145 S3 H190.00 B50.00 F128
Recv: echo:; Hotend PID:
Recv: echo:  M301 P21.73 I1.54 D76.55
Recv: echo:; Bed PID:
Recv: echo:  M304 P462.10 I85.47 D624.59
Recv: echo:; Retract (S<length> F<feedrate> Z<lift>):
Recv: echo:  M207 S5.00 W13.00 F2400.00 Z0.20
Recv: echo:; Recover (S<length> F<feedrate>):
Recv: echo:  M208 S0.00 W0.00 F2400.00
Recv: echo:; Homing Feedrate:
Recv: echo:  M210 X3000.00 Y3000.00 Z600.00
Recv: echo:; Z-Probe Offset:
Recv: echo:  M851 X-41.50 Y-6.89 Z-1.70 ; (mm)
Recv: echo:; Hotend Idle Timeout:
Recv:   M86 B0 E0 S600 T170
Recv: echo:; Filament load/unload:
Recv: echo:  M603 L0.00 U100.00 ; (mm)
Recv: echo:; Filament runout sensor:
Recv: echo:  M412 S0 D25.00 ; Sensor OFF
Recv: echo:; Physical minimums:
Recv: echo:  C100 X0 Y0
Recv: echo:; Physical maximums:
Recv: echo:  C101 X248 Y231 Z250
Recv: echo:; Bed size:
Recv: echo:  C102 X230 Y230
Recv: echo:; Mesh inset and leveling settings:
Recv: echo:  C29 L25 R205 F25 B205 X9 Y9 ; 9x9
Recv: echo:; Max Extruder temperature:
Recv: echo:  C104 T275
Recv: echo:; Park Head:
Recv: echo:  C125 X240 Y221 Z20
Recv: echo:; Filament runout sensor:
Recv: echo:  C412 M0 ; Active mode: LOW
Recv: echo:; Invert Extruder:
Recv: echo:  C562 E0 ; No inverted
Recv: echo:; Probe Z Fix, Speed and Multiple Probing:
Recv: echo:  C851 F0.00000 S480 M0
Recv: ok P15 B15
Recv:  T:19.89 /0.00 B:19.77 /0.00 @:0 B@:0
Recv:  T:19.88 /0.00 B:19.79 /0.00 @:0 B@:0
Send: M420 V
Recv: 
Recv: Bed Topography Report:
Recv: 
Recv:     ( 25,205)                                                      (205,205)
Recv:         0       1       2       3       4       5       6       7       8
Recv:  8 | +1.510  +1.202  +0.750  +0.445  -0.329  -0.129  -0.417  -0.572  -0.462
Recv:    |
Recv:  7 | +1.717  +1.222  +0.417  -0.112  -0.414  -0.707  -1.002  -1.027  -0.289
Recv:    |
Recv:  6 | +1.892  +0.922  +0.387  +0.062  -0.247  -0.549  -0.839  -1.129  -0.307
Recv:    |
Recv:  5 | +1.897  +0.897  +0.567  +0.232  -0.064  -0.367  -0.669  -0.969  -0.799
Recv:    |
Recv:  4 | +0.917  +1.095  +0.767  +0.442  -0.029  -0.172  -0.489  -0.792  -0.629
Recv:    |
Recv:  3 | +0.725  +1.312  +0.995  +0.660  +0.352  +0.052  -0.237  -0.549  -0.372
Recv:    |
Recv:  2 | +0.578  +1.735  +1.197  +0.887  +0.587  +0.290  -0.022  -0.312  -0.124
Recv:    |
Recv:  1 |  0.000  +0.885  +1.620  +1.090  +0.795  +0.497  +0.190  +0.172  +0.967
Recv:    |
Recv:  0 |  0.000  +0.815  +0.930  +0.957  +1.262  +0.997  +1.182  +1.105  +1.425
Recv:         0       1       2       3       4       5       6       7       8
Recv:     ( 25, 25)                                                      (205, 25)
Recv: 
Recv: Mesh is valid
Recv: Storage slot: 0
Recv: echo:Bed Leveling OFF
Recv: echo:Fade Height 10.00
Recv: ok P15 B15
Recv:  T:19.92 /0.00 B:19.80 /0.00 @:0 B@:0
Recv:  T:19.90 /0.00 B:19.79 /0.00 @:0 B@:0
Recv:  T:19.88 /0.00 B:19.72 /0.00 @:0 B@:0
Connection closed, closing down monitor
Changing monitoring state from "Operational" to "Offline"