Contents
- Introduction
- Design Principles
- Getting Started
- Varnish Distribution
- Exercise: Install Varnish
- Exercise: Configure Varnish
- The front-end
varnishadm
of the Varnish Command Line Interface (CLI) - More About Varnish Configuration
- Command Line Configuration
- Defining a Backend in VCL
- Exercise: Use the administration interface to learn, review and set Varnish parameters
- Exercise: Fetch Data Through Varnish
- Examining Varnish Server's Output
- Tuning
- HTTP
- VCL Basics
- Varnish Finite State Machine
- Detailed Varnish Request Flow for the Client Worker Thread
- The VCL Finite State Machine
- VCL Syntax
- VCL Built-in Functions and Keywords
- Legal Return Actions
- Variables in VCL subroutines
- Built-in
vcl_recv
- Detailed Varnish Request Flow for the Backend Worker Thread
- VCL –
vcl_backend_response
- Waiting State
- Summary of VCL Basics
- VCL Subroutines
- Cache Invalidation
- Saving a Request
- Content Composition
- Varnish Plus Software Components
- Appendix A: Resources
- Appendix B: Varnish Programs
varnishtop
varnishncsa
varnishhist
- Exercise: Try
varnishstat
,varnishlog
andvarnishhist
varnishtest
- The Varnish Test Case (VTC) Language
- Synchronization in Varnish Tests
- Running Your Varnish Test Cases
- Exercise: Test Apache as Backend with
varnishtest
- Setting Parameters in
varnishtest
- Fetch Data with
varnishtest
- Understanding
Expires
invarnishtest
- Example of Transactions in
varnishtest
logexpect
- Exercise: Assert Counters in
varnishtest
- Understanding
Vary
invarnishtest
- Understanding
Last-Modified
andIf-Modified-Since
invarnishtest
- Understanding
Cache-Control
invarnishtest
- VCL in
varnishtest
PURGE
invarnishtest
- Cache Invalidation in
varnishtest
- Understanding Grace using
varnishtest
- Exercise: Handle Cookies with
Vary
andhash_data()
invarnishtest
- Understanding ESI in
varnishtest
- Appendix C: Extra Material
- Appendix D: VMOD Development
- Appendix E: Varnish Three Letter Acronyms
- Appendix F: Apache as Backend
- Appendix G: Solutions
- Solution: Install Varnish
- Solution: Test Apache as Backend with
varnishtest
- Solution: Assert Counters in
varnishtest
- Solution: Tune
first_byte_timeout
and test it against mock-up server - Solution: Configure
vcl_recv
to avoid caching all requests to the URL/admin
- Solution: Configure Threading with
varnishadm
andvarnishstat
- Solution: Configure Threading with
varnishtest
- Solution: Rewrite URL and Host Header Fields
- Solution: Avoid caching a page
- Solution: Either use
s-maxage
or set TTL by file type - Solution: Modify the HTTP response header fields
- Solution: Change the error message
- Solution:
PURGE
an article from the backend - Solution: Write a VCL program using purge and ban
- Solution: Handle Cookies with
Vary
invarnishtest
- Solution: Handle Cookies with
hash_data()
invarnishtest
- Solution: Write a VCL that masquerades XHR calls
Abstract
The Varnish Book is the training material for Varnish Plus courses.
This book teaches such concepts to understand the theory behind Varnish Cache 4.
Covered are the Varnish finite state machine, design principles, HTTP, cache invalidation and more.
With these foundations, the book builds practical knowledge on Varnish Configuration Language (VCL), Varnish Test Code (VTC) and Varnish utility programs such as varnishlog
, varnishstat
and varnishtest
.
Examples and exercises develop the needed skills to administrate and extend the functionality of Varnish.
Also included are appendices that explain how to develop Varnish Modules (VMODs) and how to use selected modules of Varnish Plus.
Preface
- Course for Varnish Plus
- Learn specific features depending the course and your needs
- Necessary Background
- How to Use the Book
- Acknowledgments
After finishing this course, you will be able to install and configure the Varnish server, and write effective VCL code. The Varnish Book is designed for attendees of Varnish Plus courses. Most of the presented material in this book applies to both, the open source Varnish Cache and the commercial edition Varnish Cache Plus. Therefore, you can also refer to the Varnish Cache documentation at https://www.varnish-cache.org/docs/4.0/.
Varnish Plus is a commercial suite by Varnish Software that offers products for scalability, customization, monitoring, and expert support services. The engine of Varnish Plus is Varnish Cache Plus, which is the enhanced commercial edition of Varnish Cache. Varnish Cache Plus should not be confused with Varnish Plus, a product offering by Varnish Software. Varnish Cache Plus is one of the software components available for Varnish Plus customers.
For simplicity, the book refers to Varnish Cache or Varnish Cache Plus as Varnish when there is no difference between them. There is more information about differences between Varnish Cache and Varnish Cache Plus in the Varnish Cache and Varnish Plus chapter.
The goal of this book is to make you confident when using Varnish. Varnish instructors focus on your area, needs or interest. Varnish courses are usually flexible enough to make room for it.
The instructor will cover selected material for the course you take. The System Administration (Admin) course provides attendees with the necessary knowledge to troubleshoot and tune common parameters of a Varnish server. The Web Developer (Webdev) course teaches how to adapt web applications so that they work with Varnish, which guarantees a fast experience for visitors of any website. Besides that, other courses may also be taught with this book.
Necessary Background
The Admin course requires that you:
- have expertise in a shell on a Linux/UNIX machine, including editing text files and starting daemons,
- understand HTTP cache headers,
- understand regular-expressions, and
- be able to install the software listed below.
The Webdev course requires that you:
- have expertise in a shell on a Linux/UNIX machine, including editing text files and starting daemons,
- understand HTTP cache headers,
- understand regular-expressions, and
- be able to install the software listed below.
You do not need background in theory or application behind Varnish to complete this course. However, it is assumed that you have experience and expertise in basic UNIX commands, and that you can install the following software:
- Varnish Cache 4.x or Varnish Cache Plus 4.x,
- Apache/2.4 or later,
- HTTPie 0.8.0 or later,
- PHP 5.4 or later, and
- curl – command line tool for transferring data with URL syntax
More specific required skills depend on the course you take. The book starts with the installation of Varnish and navigation of some of the common configuration files. This part is perhaps the most UNIX-centric part of the course.
How to Use the Book
- Most of the material in this book applies to both: Varnish Cache and Varnish Cache Plus. Parts that apply only to Varnish Cache Plus are clearly stated.
- Varnish caching mechanisms are different than in other caching technologies. Open your mind and try to think different when using Varnish.
- The instructor guides you through the book.
- Use the manual pages and help options.
- See Appendix E: Varnish Three Letter Acronyms for a list of acronyms.
The Varnish Book is designed to be used as training material under the Varnish Plus course taught by a certified instructor. Under the course, the instructor guides you and selects the relevant sections to learn. However, you can also use this book as self-instructional material.
There are almost always many ways to do an exercise. The solutions provided in Appendix G: Solutions are not necessarily better than yours.
Varnish installs several reference manuals that are accessible through the manual page command man
.
You can issue the command man -k varnish
to list the manual pages that mention Varnish in their short description.
In addition, the vsl
man page that explains the Varnish Shared memory Logging (VSL).
This man page does not come out when issuing man -k varnish
, because it does not contain the word varnish in its short description.
The command man varnishd
, for example, retrieves the manual page of the Varnish HTTP accelerator daemon.
Also, some commands have a help option to print the usage of the command.
For example, varnishlog -h
prints the usage and options of the command with a short description of them.
In addition, you should refer to the documentation of Varnish Cache and Varnish Cache Plus. This documentation provides you extended details on the topics covered in this book and more. To access to this documentation, please visit https://www.varnish-software.com/resources.
The Varnish installation described in this book uses Ubuntu Linux 14.04 LTS (trusty), therefore most of the commands instructed in this book are for this Linux distribution. We point out some differences on how to configure Varnish for other Linux distributions, but you should reference your Linux distribution's documentation for more details.
The book is written with different formatting conventions. Varnish Configuration Language (VCL) code uses the mono-spaced font type inside boxes:
vcl 4.0; backend default { .host = "127.0.0.1"; .port = "8080"; } sub vcl_recv { # Do request header transformations here. if (req.url ~ "^/admin") { return(pass); } }
The first occurrence of a new term is usually its definition, and appears in italics.
File names are indicated like this: /path/to/yourfile
.
Important notes, tips and warnings are also inside boxes, but they use the normal body text font type.
Resources, and Errata
- https://varnish-cache.org
- https://varnish-software.com/academy
- #varnish-hacking and #varnish on irc.linpro.net.
- https://github.com/varnish/Varnish-Book/
- https://www.varnish-cache.org/docs/trunk/users-guide/troubleshooting.html
- https://www.varnish-cache.org/trac/wiki/VCLExamples
This book is meant to be understandable to everyone who takes a Varnish Plus course and has the required skills. If you find something unclear, do not be shy and blame yourself, ask your instructor for help. You can also contact the Varnish open source community at https://varnish-cache.org. To book training, please look at https://varnish-software.com/academy.
Additional examples from different Varnish versions are available at https://www.varnish-cache.org/trac/wiki/VCLExamples. These examples are maintained by the community.
For those interested in development, the developers arrange weekly bug washes where recent tickets and development is discussed. This usually takes place on Mondays around 13:00 CET on the IRC channel #varnish-hacking on irc.linpro.net.
Errata, updates and general improvements of this book are available at its repository https://github.com/varnish/Varnish-Book.
Acknowledgments
In addition to the authors, the following deserve special thanks (in no particular order):
- Rubén Romero
- Dag Haavi Finstad
- Martin Blix Grydeland
- Reza Naghibi
- Federico G. Schwindt
- Dridi Boukelmoune
- Lasse Karstensen
- Per Buer
- Sevan Janiyan
- Kacper Wysocki
- Magnus Hagander
- Arianna Aondio
- Poul-Henning Kamp
- Guillaume Quintard
- Everyone who has participated on the training courses
Table of contents:
- What is Varnish?
- Benefits of Varnish
- Open source / Free software
- Varnish Software: The company
- What is Varnish Plus?
- Varnish: more than a cache server
- History of Varnish
- Varnish Governance Board (VGB)
Varnish is a reverse HTTP proxy, sometimes referred to as an HTTP accelerator or a web accelerator. A reverse proxy is a proxy server that appears to clients as an ordinary server. Varnish stores (caches) files or fragments of files in memory that are used to reduce the response time and network bandwidth consumption on future, equivalent requests. Varnish is designed for modern hardware, modern operating systems and modern work loads.
Varnish is more than a reverse HTTP proxy that caches content to speed up your server. Depending on the installation, Varnish can also be used as:
- web application firewall,
- DDoS attack defender,
- hotlinking protector,
- load balancer,
- integration point,
- single sign-on gateway,
- authentication and authorization policy mechanism,
- quick fix for unstable backends, and
- HTTP router.
Example of Varnish Configuration Language (VCL):
vcl 4.0; backend default { .host = "127.0.0.1"; .port = "8080"; } sub vcl_recv { # Do request header transformations here. if (req.url ~ "^/admin") { return(pass); } }
Varnish Cache is an open source project, and free software. The development process is public and everyone can submit patches, or just take a peek at the code if there is some uncertainty on how does Varnish Cache work. There is a community of volunteers who help each other and newcomers. The BSD-like license used by Varnish Cache does not place significant restriction on re-use of the code, which makes it possible to integrate Varnish Cache in virtually any solution.
Varnish Cache is developed and tested on GNU/Linux and FreeBSD. The code-base is kept as self-contained as possible to avoid introducing out-side bugs and unneeded complexity. Therefore, Varnish uses very few external libraries.
Varnish Software is the company behind Varnish Cache. Varnish Software and the Varnish community maintain a package repository of Varnish Cache for several common GNU/Linux distributions.
Varnish Software also provides a commercial suite called Varnish Plus with software products for scalability, customization, monitoring and expert support services. The engine of the Varnish Plus commercial suite is the enhanced commercial edition of Varnish Cache. This edition is proprietary and it is called Varnish Cache Plus.
Table 1 shows the components covered in this book and their availability for Varnish Cache users and Varnish Plus customers. The covered components of Varnish Plus are described in the Varnish Plus Software Components chapter. For more information about the complete Varnish Plus offer, please visit https://www.varnish-software.com/what-is-varnish-plus. A list of supported platforms can be found in https://www.varnish-software.com/customers/#platforms.
Note
Varnish Cache Plus should not be confused with Varnish Plus, a product offering by Varnish Software. Varnish Cache Plus is one of the software components available for Varnish Plus customers.
- 2005: Ideas! Verdens Gang (www.vg.no, Norway's biggest newspaper) were looking for alternative cache solutions
- 2006: Work began: Redpill Linpro was in charge of project management, infrastructure and supporting development. Poul-Henning Kamp did the majority of the actual development.
- 2006: Varnish 1.0 is released
- 2008: Varnish 2.0 is released
- 2008:
varnishtest
is introduced - 2009: The first Varnish User Group Meeting is held in London Roughly a dozen people participate from all around the world
- 2010: Varnish Software is born as a spin-off to Redpill Linpro AS
- 2011: Varnish 3.0 is released
- 2012: The fifth Varnish User Group Meeting is held in Paris Roughly 70 people participate on the User-day and around 30 on the developer-day!
- 2012: The Varnish Book is published
- 2013: Varnish Software chosen as a 2013 Red Herring Top 100 Europe company
- 2013: BOSSIE award winner
- 2013: Varnish Software receives World Summit on Innovation & Entrepreneurship Global Hot 100 award
- 2014: Varnish Plus is launched
- 2014: Varnish 4.0 is released
- 2015: Varnish API Engine is released
- 2015: Gartner names Varnish Software as a 2015 ‘Cool Vendor’ in Web-Scale Platforms
- 2015: Varnish Plus supports SSL/TLS
- 2016: Varnish in the cloud
- 2016: Varnish 5.0 is released
VG, a large Norwegian newspaper, initiated the Varnish project in cooperation with Linpro. The lead developer of the Varnish project, Poul-Henning Kamp, is an experienced FreeBSD kernel hacker. Poul-Henning Kamp continues to bring his wisdom to Varnish in most areas where it counts.
From 2006 throughout 2008, most of the development was sponsored by VG, API, Escenic and Aftenposten, with project management, infrastructure and extra man-power provided by Redpill Linpro. At the time, Redpill Linpro had roughly 140 employees mostly centered around consulting services.
Today Varnish Software is able to fund the core development with income from service agreements, in addition to offering development of specific features on a case-by-case basis. The interest in Varnish continues to increase. An informal study based on the list of most popular web sites in Norway indicates that about 75% or more of the web traffic that originates in Norway is served through Varnish.
Varnish development is governed by the Varnish Governance Board (VGB), which thus far has not needed to intervene. The VGB consists of an architect, a community representative and a representative from Varnish Software.
As of November 2015, the VGB positions are filled by Poul-Henning Kamp (Architect), Rogier Mulhuijzen (Community) and Lasse Karstensen (Varnish Software). On a day-to-day basis, there is little need to interfere with the general flow of development.
- Version statement
vcl 4.0;
req.request
is nowreq.method
vcl_fetch
is nowvcl_backend_response
- Directors have been moved to the
vmod_directors
- Hash directors as a client directors
vcl_error
is nowvcl_backend_error
error()
is nowsynth()
, and you must explicitly return it:return (synth(999, "Response"));
- Synthetic responses in
vcl_synth
- Setting headers on synthetic response bodies made in
vcl_synth
are now done onresp.http
instead ofobj.http
. obj.*
invcl_error
replaced byberesp.*
invcl_backend_error
hit_for_pass
objects are created usingberesp.uncacheable
req.*
not available invcl_backend_response
bereq.*
invcl_backend_response
vcl_*
prefix reserved for builtin subroutinesreq.backend.healthy
replaced bystd.healthy(req.backend_hint)
client.port
andserver.port
replaced bystd.port(client.ip)
andstd.port(server.ip)
- Cache invalidation with purges is now done via
return(purge)
invcl_recv
obj.*
is now read-onlyobj.last_use
is retiredvcl_recv
must now returnhash
instead oflookup
vcl_hash
must now returnlookup
instead ofhash
vcl_pass
must now returnfetch
instead ofpass
restart
in the backend is nowretry
, this is now calledreturn(retry)
, and jumps back up tovcl_backend_fetch
- default VCL is now called builtin VCL
- The builtin VCL now honors
Cache-Control: no-cache
(and friends) to indicate uncacheable content from the backend remove
keyword replaced byunset
X-Forwarded-For
is now set beforevcl_recv
session_linxger
has been renamed totimeout_linger
and it is in seconds now (previously was milliseconds)sess_timeout
is renamed totimeout_idle
- Increasing
sess_workspace
is not longer necessary, you may need to increase either workspace_backend or workspace_client thread_pool_purge_delay
is renamed tothread_pool_destroy_delay
and it is in seconds nowthread_pool_add_delay
andthread_pool_fail_delay
are in seconds now- New parameter
vcc_allow_inline_c
to disable inline C in your VCL - New query language to filter logs:
-m
option replaced by-q
The above list tries to summarize the most important changes from Varnish Cache 3 to Varnish Cache 4. For more information, please visit: https://varnish-cache.org/docs/4.1/whats-new/index.html
If you want to migrate your VCL code from Varnish 3 to Varnish 4, you may be interested in looking at the varnish3to4 script. See the VCL Migrator from Varnish 3 to Varnish 4 section for more information.
Varnish is designed to:
- Solve real problems
- Run on modern hardware (64-bit multi-core architectures)
- Work with the kernel, not against it
- Translate Varnish Configuration Language (VCL) to C programming language
- Be extendible via Varnish Modules (VMODs)
- Reduce lock-contention via its workspace-oriented shared memory model
The focus of Varnish has always been performance and flexibility. Varnish is designed for hardware that you buy today, not the hardware you bought 15 years ago. This is a trade-off to gain a simpler design and focus resources on modern hardware. Varnish is designed to run on 64-bit architectures and scales almost proportional to the number of CPU cores you have available. Though CPU-power is rarely a problem.
32-bit systems, in comparison to 64-bit systems, allow you to allocate less amount of virtual memory space and less number of threads. The theoretical maximum space depends on the operating system (OS) kernel, but 32-bit systems usually are bounded to 4GB. You may get, however, about 3GB because the OS reserves some space for the kernel.
Varnish uses a workspace-oriented memory-model instead of allocating the exact amount of space it needs at run-time. Varnish does not manage its allocated memory, but it delegates this task to the OS because the kernel can normally do this task better than a user-space program.
Event filters and notifications facilities such as epoll
and kqueue
are advanced features of the OS that are designed for high-performance services like Varnish.
By using these, Varnish can move a lot of the complexity into the OS kernel which is also better positioned to decide which threads are ready to execute and when.
Varnish uses the Varnish Configuration Language (VCL) that allows you to specify exactly how to use and combine the features of Varnish. VCL is translated to C programming language code. This code is compiled with a standard C compiler and then dynamically linked directly into Varnish at run-time.
When you need functionalities that VCL does not provide, e.g., look for an IP address in a database, you can write raw C code in your VCL. That is in-line C in VCL. However, in-line C is strongly discouraged because in-line C is more difficult to debug, maintain and develop with other developers. Instead in adding in-line C, you should modularized your C code in Varnish modules, also known as VMODs.
VMODs are typically coded in VCL and C programming language. In practice, a VMOD is a shared library with functions that can be called from VCL code.
The standard (std
) VMOD, included in Varnish Cache, extends the functionality of VCL.
std
VMOD includes non-standard header manipulation, complex header normalization and access to memcached among other functionalities.
Appendix D: VMOD Development explains in more details how VMODs work and how to develop yours.
The Varnish Shared memory Log (VSL) allows Varnish to log large amounts of information at almost no cost by having other applications parse the data and extract the useful bits. This design and other mechanisms decrease lock-contention in the heavily threaded environment of Varnish.
To summarize: Varnish is designed to run on modern hardware under real work-loads and to solve real problems. Varnish does not cater to the "I want to make Varnish run on my 486 just because"-crowd. If it does work on your 486, then that's fine, but that's not where you will see our focus. Nor will you see us sacrifice performance or simplicity for the sake of niche use-cases that can easily be solved by other means -- like using a 64-bit OS.
- Object: local store of HTTP response message
- Objects in Varnish are stored in memory and addressed by hash keys
- You can control the hashing
- Multiple objects can have the same hash key
Objects are local stores of response messages as defined in https://tools.ietf.org/html/rfc7234. They are mapped with a hash key and they are stored in memory. References to objects in memory are kept in a hash tree.
A rather unique feature of Varnish is that it allows you to control the input of the hashing algorithm. The key is by default made out of the HTTP Host header and the URL, which is sufficient and recommended for typical cases. However, you are able to create the key from something else. For example, you can use cookies or the user-agent of a client request to create a hash key.
HTTP specifies that multiple objects can be served from the same URL depending on the preferences of the client. For instance, content in gzip format is sent only to clients that indicate gzip support. Varnish stores a single compressed object under one hash key.
Upon a client request, Varnish checks the Accept-Encoding
header field.
If the client does not accept gzip objects, Varnish decompresses the object on the fly and sends it to the client.
Figure 2 shows the lifetime of cached objects.
A cached object has an origin timestamp t_origin
and three duration attributes: 1) TTL
, 2) grace
, and 3) keep
.
t_origin
is the time when an object was created in the backend.
An object lives in cache until TTL + grace + keep
elapses.
After that time, the object is removed by the Varnish daemon.
In a timeline, objects within the time-to-live TTL
are considered fresh objects.
Stale objects are those within the time period TTL
and grace
.
Objects within t_origin
and keep
are used when applying conditions with the HTTP header field If-Modified-Since
.
The VCL – vcl_backend_fetch and VCL – vcl_backend_response sections explain how Varnish handles backend responses and how these duration attributes affect subsequent actions.
In this chapter, you will:
- learn about the Varnish distribution,
- install Varnish, and
- cover basic Varnish configuration.
Most of the commands you will type in this course require root privileges.
You can get temporary root privileges by typing sudo <command>
, or permanent root privileges by typing sudo -i
.
In Varnish terminology, a backend is the origin server. In other words, it is whatever server Varnish talks to fetch content. This can be any sort of service as long as it understands HTTP. Most of the time, Varnish talks to a web server or an application frontend server. In this book, we use backend, origin server, web server or application frontend server depending the context.
Utility programs part of the Varnish distribution:
varnishd
varnishtest
varnishadm
varnishlog
varnishstat
- and more
The Varnish distribution includes several utility programs that you will use in this course. You will learn how to use these programs as you progress, but it is useful to have a brief introduction about them before we start.
The central block of Varnish is the Varnish daemon varnishd
.
This daemon accepts HTTP requests from clients, sends requests to a backend, caches the returned objects and replies to the client request.
varnishd
is further explained in the Varnish Architecture section.
varnishtest
is a script driven program used to test your Varnish installation.
varnishtest
is very powerful because it allows you to create client mock-ups, fetch content from mock-up or real backends, interact with your actual Varnish configuration, and assert the expected behavior.
varnishtest
is also very useful to learn more about the behavior of Varnish.
varnishadm
controls a running Varnish instance.
The varnishadm
utility establishes a command line interface (CLI) connection to varnishd
.
This utility is the only one that may affect a running instance of Varnish.
You can use varnishadm
to:
- start and stop
varnishd
, - change configuration parameters,
- reload the Varnish Configuration Language (VCL),
- view the most up-to-date documentation for parameters, and
- more.
The front-end varnishadm of the Varnish Command Line Interface (CLI) section explains in more detail this utility.
The Varnish log provides large amounts of information, thus it is usually necessary to filter it.
For example, "show me only what matches X".
varnishlog
does precisely that.
You will learn more about varnishlog
in the Examining Varnish Server's Output chapter.
varnishstat
is used to access global counters.
It provides overall statistics, e.g the number of total requests, number of objects, and more.
varnishstat
is particularly useful when using it together with varnishlog
to analyze your Varnish installation.
The varnishstat section explains in detail this utility.
In addition, there are other utility programs such as varnishncsa
, varnishtop
and varnishhist
.
Appendix B: Varnish Programs explains them.
- Install Varnish
- Use packages provided by
- varnish-software.com for Varnish Cache Plus
- varnish-cache.org for Varnish Cache
- When you are done, verify your Varnish version, run
varnishd -V
For official training courses, a varnish-plus
package should already be
available for installation. When in doubt, ask your instructor to confirm
which package should be installed.
You may skip this exercise if already have a well configured environment to test Varnish. In case you get stuck, you may look at the proposed solution.
[1] There is no configuration file.
Use the command chkconfig varnishlog/varnishncsa on/off
instead.
[2] Create a drop-in systemd service file in /etc/systemd/system/varnish.service.d/customexec.conf
:
[Service] ExecStart= ExecStart=/usr/sbin/varnishd -a :80 -T localhost:6082 -f \ /etc/varnish/default.vcl -S /etc/varnish/secret -s malloc,256m
This file overrides the ExecStart
option of the default configuration shipped with Varnish Cache.
Run systemctl daemon-reload
to make sure systemd picks up the new configuration before restarting Varnish.
[3] Create a drop-in systemd service file in /etc/systemd/system/varnishlog.service.d/customexec.conf
to customize your varnishlog
configuration.
[4] Create a drop-in systemd service file in /etc/systemd/system/varnishncsa.service.d/customexec.conf
.
In this file you can for example set VARNISHNCSA_ENABLED=1
.
[5] There is no configuration file.
Use the command systemctl start/stop/enable/disable/ varnishlog/varnishncsa
instead.
The configuration file is used to give parameters and command line arguments to the Varnish daemon.
This file also specifies the location of the VCL file.
Modifications to this file require to run service varnish restart
for the changes to take effect.
The location of the Varnish configuration file depends on the operating system and whether it uses the init
system of SysV, or systemd.
Table 3 shows the locations for each system installation.
To install packages on Ubuntu or Debian, use the command apt-get install <package>
, e.g., apt-get install varnish
.
For CentOS, RHEL or Fedora, use yum install <package>
.
You might want to look at Solution: Install Varnish, if you need help.
If the command service varnish restart
fail, try to start Varnish manually to get direct feedback from the shell.
Command example:
$ sudo /usr/sbin/varnishd -j unix,user=varnish,ccgroup=varnish \ -P /var/run/varnish.pid -f /etc/varnish/default.vcl -a :80 -a :6081,PROXY \ -T 127.0.0.1:6082 -t 120 -S /etc/varnish/secret \ -s malloc,256MB -F
Configure listening ports for client requests and Varnish administration
In CentOS 7:
/etc/varnish/varnish.params
Variable substitution in
/usr/lib/systemd/system/varnish.service
:-a ${VARNISH_LISTEN_ADDRESS}:${VARNISH_LISTEN_PORT} -T ${VARNISH_ADMIN_LISTEN_ADDRESS}:${VARNISH_ADMIN_LISTEN_PORT}
Configure one backend in VCL file
/etc/varnish/default.vcl
See Table 3 and locate the Varnish configuration file for your installation.
Open and edit that file to listen to client requests on port 80
and have the management interface on port 1234.
In Ubuntu and Debian, this is configured with options -a
and -T
of variable DAEMON_OPTS
.
In CentOS, RHEL, and Fedora, use VARNISH_LISTEN_PORT
and VARNISH_ADMIN_LISTEN_PORT
respectively.
In order for changes in the configuration file to take effect, varnishd must be restarted.
The safest way to restart Varnish is by using service varnish restart
.
The default VCL file location is /etc/varnish/default.vcl
.
You can change this location by editing the configuration file.
The VCL file contains the backend definitions.
In this book, we use Apache as backend.
Before continuing, make sure you have Apache installed and configured to listen on port 8080
.
See Appendix F: Apache as Backend if you do not know how to do it.
Edit /etc/varnish/default.vcl
to use Apache as backend:
backend default { .host = "127.0.0.1"; .port = "8080"; }
Varnish Cache Plus supports SSL/TLS encryption. To encrypt connections between Varnish and the backend, you specify it as follows:
backend default { .host = "host.name"; .port = "https"; # This defaults to https when SSL .ssl = 1; # Turns on SSL support .ssl_nosni = 0; # Disable SNI extension .ssl_noverify = 1; # Don't verify peer }
For Varnish to accept incoming encrypted connections, you need a terminator for encrypted connections such as hitch https://github.com/varnish/hitch. Varnish Plus 4.1 has integrated this functionality and you can easily configure it as detailed in SSL/TLS frontend support with hitch.
varnishd
can reload VCL programs without restart
service varnish reload
or:
systemctl reload varnish
or:
varnishadm vcl.load vcl01 /etc/varnish/default.vcl varnishadm vcl.use vcl01
service varnish reload
is a shortcut to reload VCL programs.
varnishadm vcl.load <compiledVCL> <VCLsourcecode>
compiles the VCL program you specify.
You can have multiple compiled files in Varnish.
To see them, run:
varnishadm vcl.list
To apply a compiled VCL program, type:
varnishadm vcl.use <compiledVCL>
This command does not restart varnishd
, it only reloads the compiled VCL code.
The result of your configuration is resumed in Table 4.
* These files are for a SysV Ubuntu/Debian configuration
You can get an overview over services listening on TCP ports by issuing the command netstat -nlpt
.
Within the result, you should see something like:
tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN 9223/varnishd tcp 0 0 127.0.0.1:1234 0.0.0.0:* LISTEN 9221/varnishd
Warning
If you have Security-Enhanced Linux (SELinux), be aware that SELinux defines ports 6081
and 6082
for varnishd
.
If you need to use another port number, you need either to disable SELinux or set the boolean varnishd_connect_any
variable to 1.
You can do that by executing the command sudo setsebool varnishd_connect_any 1
.
Tip
Issue the command man vcl
to see all available options to define a backend.
Tip
You can also configure Varnish via the Varnish Administration Console (VAC).
Run
http -p Hh localhost
Your output should look as:
# http -p Hh localhost GET / HTTP/1.1 Accept: */* Accept-Encoding: gzip, deflate, compress Host: localhost User-Agent: HTTPie/0.8.0 HTTP/1.1 200 OK Accept-Ranges: bytes Age: 0 Connection: keep-alive Content-Encoding: gzip Content-Length: 3256 Content-Type: text/html Date: Wed, 18 Mar 2015 13:55:28 GMT ETag: "2cf6-5118f93ad6885-gzip" Last-Modified: Wed, 18 Mar 2015 12:53:59 GMT Server: Apache/2.4.7 (Ubuntu) Vary: Accept-Encoding Via: 1.1 varnish-plus-v4 X-Varnish: 32770
You can test your Varnish installation by issuing the command http -p Hh localhost
.
If you see the HTTP response header field Via
containing varnish
, then your installation is correct.
The X-Varnish
HTTP header field contains the Varnish Transaction ID (VXID) of the client request and if applicable, the VXID of the backend transaction that stored in cache the object delivered.
X-Varnish
is useful to find the correct log entries in the Varnish log.
For a cache hit, X-Varnish
contains both the ID of the current request and the ID of the request that populated the cache.
You will learn more about VXIDs in the Transactions section.
You can also define and test connectivity against any backend in varnishtest
.
Learn how to it by doing the Exercise: Test Apache as Backend with varnishtest.
You can use the varnishadm
utility to:
- start and stop the cacher (aka child) process
- change configuration parameters without restarting Varnish
- reload the Varnish Configuration Language (VCL) without restarting Varnish
- view the most up-to-date documentation for parameters
varnishadm help
andman varnishadm
Varnish has a command line interface (CLI) which can control and change most of the operational parameters and the configuration of the Varnish daemon, without interrupting the running service.
varnishadm
is front-end to the Varnish interface.
In practice, it is a utility program with a set of functions that interact with the Varnish daemon varnishd
.
If there are many Varnish instances running in one machine, specify the instance with the -n
option of varnishadm
.
Keep the following in mind when issuing commands to the Varnish daemon:
- Changes take effect on the running Varnish daemon instance without need to restart it.
- Changes are not persistent across restarts of Varnish. If you change a parameter and you want the change to persist after you restart Varnish, you need to store your changes in the configuration file of the boot script. The location of the configuration file is in Table 3
varnishadm
uses a non-encrypted key stored in a secret file to authenticate and connect to a Varnish daemon.
You can control access by adjusting the read permission on the secret file.
varnishadm
looks for the secret file in /etc/varnish/secret
by default, but you can use the -S
option to specify another location.
The content of the file is a shared secret, which is a string generated under Varnish installation.
varnishadm
authenticates with a challenge-response mechanism.
Therefore, the shared secret is never transmitted, but a challenge and the response to the challenge.
This authentication mechanism offers a reasonably good access control, but it does not protect the data transmitted over the connection.
In order to avoid eavesdroppers like in the man-in-the-middle attack, we recommend that you configure the management interface listening address of varnishd
to listen only on localhost
(127.0.0.1
IP address).
You configure this address with the -T
option of the varnishd
command.
For convenience, varnishadm
has an embedded command line tool.
You can access it by simply issuing varnishadm
in the terminal.
Tip
Varnish provides many on-line reference manuals.
To learn more about varnishadm
, issue man varnishadm
.
To check the Varnish CLI manual page, issue man varnish-cli
.
Tip
You can also access the varnishadm
via the Varnish Administration Console (VAC).
To do that, you just have to navigate to the CONFIGURE tab and click on the Varnish server you want to administrate.
Then, varnishadm
is ready to use in a terminal emulator right in your web browser.
![ui/img/vac_varnishadm.png](/varnish/Varnish-Book/raw/master/ui/img/vac_varnishadm.png)
Figure :counter:`figure`: Access to varnishadm
by clicking on the Varnish server that you want to administrate.
The location of the configuration file is in Table 3.
Using the service
commands is recommended, safe and fast.
Command line options and tunable parameters are used to: 1) define how Varnish should work with operating system and hardware, and 2) set default values. Configuration in VCL defines how Varnish should interact with web servers and clients.
Almost every aspect of Varnish can be reconfigured without restarting Varnish. Notable exceptions are: 1) allocated memory size for caching, 2) cache file location, 3) ownership (for user and group privileges) of the Varnish daemon, and 4) the hashing algorithm.
Some parameters changes require to restart Varnish to take effect. For example, the modification of the listening port. Other changes might not take effect immediately, but restart is not required. Changes to cache time-to-live (TTL), for instance, take effect only after the current cached objects expire. In this example, the value of the TTL parameter is only applicable to caches fetched after the TTL modification.
param.show <parameter>
outputs a description of parameter
.
The description includes when and how modifications takes effect, and the default and current value of the parameter.
There are other ways to reload VCL and make parameter-changes take effect, mostly using the varnishadm
tool.
However, using the service varnish reload
and service varnish restart
commands is a good habit.
Note
If you want to know how the service varnish
-commands work, look at the script that runs behind the scenes.
The script is in /etc/init.d/varnish
.
Warning
The varnish script-configuration (located under /etc/default/ or /etc/sysconfig/) is directly sourced as a shell script.
Pay close attention to any backslashes (\) and quotation marks that might move around as you edit the DAEMON_OPTS
environmental variable.
Relevant options for the course are:
-a <[hostname]:port> | |
listening address and port for client requests | |
-f <filename> | VCL file |
-p <parameter=value> | |
set tunable parameters | |
-S <secretfile> | |
shared secret file for authorizing access to the management interface | |
-T <hostname:port> | |
listening address and port for the management interface | |
-s <storagetype,options> | |
where and how to store objects |
All the options that you can pass to the varnishd
binary are
documented in the varnishd(1)
manual page (man varnishd
).
You may want to take a moment to skim over the options mentioned
above.
For Varnish to start, you must specify a backend.
You can specify a backend by two means:
1) declare it in a VCL file, or
2) use the -b
to declare a backend when starting varnishd
.
Though they are not strictly required, you almost always want to
specify a -s
to select a storage backend, -a
to make sure
Varnish listens for clients on the port you expect and -T
to
enable a management interface, often referred to as a telnet
interface.
For both -T
and -a
, you do not need to specify an IP, but
can use :80
to tell Varnish to listen to port 80 on all IPs
available. Make sure you do not forget the colon, as -a 80
tells Varnish to listen to the IP with the decimal-representation
"80", which is almost certainly not what you want. This is a result
of the underlying function that accepts this kind of syntax.
You can specify -p
for parameters multiple times. The workflow
for tuning Varnish parameters usually is that you first try the
parameter on a running Varnish through the management interface to
find the value you want.
Then, you store the parameter and value in a configuration file.
This file is read every time you start Varnish.
The -S
option specifies a file which contains a secret to be
used for authentication. This can be used to authenticate with
varnishadm -S
as long as varnishadm
can read the same secret
file -- or rather the same content: The content of the file can be
copied to another machine to allow varnishadm
to access the
management interface remotely.
Note
Varnish requires at least one backend, which is normally specified in the VCL file.
The VCL file is passed to varnishd
with the -f <filename.vcl>
option.
However, it is possible to start Varnish without a VCL file.
In this case, the backend is passed directly to varnishd
with the -b <hostname:port>
option.
-f
and -b
are mutually exclusive.
Tip
Type man varnishd
to see all options of the Varnish daemon.
/etc/varnish/default.vcl
The above example defines a backend named default
, where the name default is not special.
Varnish uses the first backend you specify as default.
You can specify many backends at the same time, but for now, we will only specify one to get started.
Tip
You can also add and edit your VCL code via the Varnish Administration Console (VAC). This interface also allows you to administrate your VCL files.
![ui/img/vac_vcl.png](/varnish/Varnish-Book/raw/master/ui/img/vac_vcl.png)
Figure :counter:`figure`: GUI of Varnish Administration Console (VAC) with command line interface to edit your VCL code.
- Use
param.show
andparam.set
fromvarnishadm
to see and set the value ofdefault_ttl
anddefault_grace
- Refer to Figure 2 to see the object's timeline
varnishtest
as explained in Setting Parameters in varnishtest.
You will learn more about how to tune parameters in the Tunable Parameters section.- Execute
http -p hH http://localhost/
on the command line - Pay attention to the
Age
response header field - Compare and discuss the results from multiple executions
-p hH
specifies HTTPie to print only request and response headers, but not the content.
The typical HTTP response is 200 OK
or 404 File not found
.
Feel free to try removing some of the options and observe the effect.
For more information about the HTTPie command, type man http
.
Testing Varnish with a web browser can be confusing, because web browsers have their own cache.
Therefore, it is useful to double-check web browsers requests with HTTPie or varnishtest
as explained in Fetch Data with varnishtest.
For more information about the Age
response header field refer to the Age
subsection.
In this chapter you will learn about:
- log records,
- statistics out from global counters and the Varnish log,
- the log layout,
- transactions,
- the query language, and
- notable counters.
Varnish logs information of requests, caches and responses to The Varnish Shared memory Log (VSL). Logs are available through Varnish tools with a short delay, but usually not noticeable. The VSL is overwritten when filled-up in circular order.
The memory log overwriting has two effects. On the one hand, there is no historic data, but on the other hand, there is an abundance of information accessible at a very high speed. Still, you can instruct Varnish to store logs in files.
Varnish generates very large amounts of data, therefore it does not write logs to disk by default, but only to memory.
However, if you need to enable logging to disk, as when debugging a crashing Varnish installation, you set VARNISHNCSA_ENABLED=1
or VARNISHNCSA_ENABLED=1
in /etc/default/varnishlog
or /etc/default/varnishncsa
respectively.
Table 3 shows the location of the configuration file based on different platforms.
Varnish provides specific tools to parse the content of logs: varnishlog
, varnishncsa
, varnishstat
, and varnishstat
among others.
varnishlog
and varnishstat
are the two most common used tools.
Tip
All utility programs have installed reference manuals.
Use the man
command to retrieve their manual pages.
Tools to display detailed log records:
varnishlog
is used to access request-specific data. It provides information about specific clients and requests.varnishncsa
displays Varnish access logs in NCSA Common log format.varnishtest
allows you to display log records and counters from your tests.
Statistical tools:
varnishstat
is used to access global counters.varnishtop
reads the Varnish log and presents a continuously updated list of the most commonly occurring log entries.varnishhist
reads the Varnish log and presents a continuously updated histogram showing the distribution of the last N requests by their processing.
If you have multiple Varnish instances running in the same machine, you need to specify -n <name>
both when starting Varnish and when using the tools.
This option is used to specify the instance of varnishd
, or the location of the shared memory log.
All tools (including varnishadm
) can also take a -n
option.
In this course, we focus on the two most important tools: varnishlog
and varnishstat
.
Unlike all other tools, varnishstat
does not read entries from the Varnish log, but from global counters.
You can find more details about the other Varnish tools varnishncsa
, varnishtop
and varnishhist
in Appendix B: Varnish Programs.
Varnish logs transactions chronologically as Figure 7 shows.
The varnishlog
is one of the most used tools and offers mechanisms to reorder transactions grouped by TCP session, frontend- or backend worker.
We talk more on transactions in the next subsection.
The various arguments of varnishlog
are mostly designed to help you find exactly what you want, and filter out the noise.
On production traffic, the amount of log data that Varnish produces is staggering, and filtering is a requirement for using varnishlog
effectively.
Next section explains transactions and how to reorder them.
varnishtest
starts a real varnishd
process for each test, therefore it also logs in VSL.
When your Varnish test fails or you run varnishtest
in verbose mode, you can see the vsl
entry for each Varnish log record.
You can also use the logexpect
to assert the expected behavior in your tests.
$ varnishlog -g <session|request|vxid|raw> -d
- You can see transactions in groups
<session|request|vxid|raw>
- The default is to group by
vxid
- The sooner a transaction ends, the sooner you see it
-d
reads all existing records in the shared memory log (VSL) instead of showing only last transactions- See Figure 8 and Figure 9 in the book
A transaction is one work item in Varnish and it is a set of log lines that belong together, e.g., a client request or a backend request.
Varnish Transaction IDs (VXIDs) are applied to lots of different kinds of work items.
A unique VXID is assigned to each type of transaction.
The 0
VXID is reserved for everything that Varnish does but not part of a specific transaction.
You can follow the VXID when you analyze the log through varnishlog
or varnishtest
.
Transaction types are:
session
: TCP sessionrequest
: Transaction handled by the frontend- or backend worker
Varnish logs are grouped by VXID by default.
For example, when viewing a log for a simple cache miss, you see logs in the order they end.
That is: 1) backend request (BeReq
), 2) client request (Request
) and 3) session (Session
).
Each transaction has a reason, for examples:
- Client request
- ESI request
- restart
- fetch
To learn more about this topic in varnishtest
, refer to the section: Example of Transactions in varnishtest.
-g <session | request | vxid | raw>
groups together transactions invarnishlog
andvarnishtest
Transaction groups are hierarchical
Levels are equal to relationships (parents and children):
Level 1: Client request (cache miss) Level 2: Backend request Level 2: ESI subrequest (cache miss) Level 3: Backend request Level 3: Backend request (VCL restart) Level 3: ESI subrequest (cache miss) Level 4: Backend request Level 2: ESI subrequest (cache hit)
When grouping transactions, there is a hierarchy structure showing which transaction initiated what. In client request grouping mode, the various work items are logged together with their originating client request. For example, a client request that triggers a backend request might trigger two more ESI subrequests, which in turn might trigger yet another ESI subrequest.
All these requests together with the client response are arranged in the order they are initiated. This arrangement is easier to grasp than when grouping by VXID. The Content Composition section shows how to analyze the log for Edge Side Includes (ESI) transactions.
When a subrequest occurs in the log, the subrequest tells us about the relationship to its parent request through the Link
statement.
This statement contains the VXID of the parent request.
varnishlog
indents its output based on the level of the request, making it easier to see the level of the current request.
$ varnishlog -g request -i Begin,Link -d
Figure 10 shows a client request in a cache miss scenario.
In the figure, varnishlog
returns records grouped by request.
For simplicity, we use the -i
option to include only the Begin
and Link
tags.
For more information about the format and content of all Varnish shared memory logging (VSL) tags, see the VSL man page by typing man vsl
.
The workflow of Varnish is detailed in the VCL Basics chapter.
To reproduce the example, issue http -p hH http://localhost/
, and then the varnishlog
command as above.
The -d
option processes all recorded entries in Varnish log.
To learn more about the available varnishlog
options, enter varnishlog -h
or see the varnishlog
man page.
varnishlog
accepts all options that are syntactically correct.
The output, however, might be different from your first interpretation.
Therefore, you should make sure that your results make sense.
Options -b
and -c
display only transactions coming from the backend and client communication respectively.
You can verify the meaning of your results by double checking the filters, and separating your results with the -b
and -c
options.
Note
The logexpect command from varnishtest
accepts the same arguments as varnishlog
.
- Operates on transaction groups.
- Query expression is true if it matches one or more records, false otherwise.
- Supports:
- string matching, e.g.:
RespProtocol eq "HTTP/1.1"
- regex, e.g.:
ReqMethod ~ "GET|POST"
- integer and float matching, e.g.:
RespStatus == 200
- boolean operators, e.g.:
RespStatus >= 500 and RespStatus < 600
- parenthesis hierarchy
- string matching, e.g.:
- Operators:
== != < <= > >= eq ne ~ !~
- Operands:
a-z A-Z 0-9 + - _ . *
Examples of Varnish log queries:
varnishlog -q 'VCL_call ~MISS' varnishlog -i Timestamp
Requests taking more than 5 seconds:
varnishlog -q 'Timestamp:Fetch[2] > 5.0'
timestamp contains timing information for the varnish worker threads.
The -q
option allows you to add a query to varnishlog
.
Think of it as a sort of select filter for varnishlog
.
It works together with the grouping so that if the query matches some part of any of the work items in the transaction group, the whole group matches and gets displayed.
Query expressions can be combined using boolean functions.
In addition, there are many output control options, such as -i
taglist.
These options are output filters, thus they do not affect transaction matching.
Output controls are applied last.
A query expression consists of record selection criteria, and optionally an operator and a value to match against the selected records:
<record selection criteria> <operator> <operand>
The <record selection criteria>
determines what kind of records from the transaction group the expression applies to.
The syntax is:
{level}taglist:record-prefix[field]
For example:
- Response time exceeds 1⁄2 second
Timestamp:Process[2] > 0.5
- Client requests connection closed
ReqHeader:connection ~ close
- ESI miss (-g request)
{3+}Begin ~ Bereq
Taglists are not case-sensitive, but we recommend you to follow the same format as declared in man vsl
.
The grouping and the query log processing all happens in the varnishlog
API.
This means that other programs using this API automatically get grouping and query language, just as logexpect
does.
See logexpect to learn more about it.
Tip
man vsl-query
shows you more details about query expressions.
man vsl
lists all taglists and their syntax.
- Provoke Varnish to get the Service Unavailable (
RespStatus == 503
) response from the backend - Use
varnishlog
to filter and print only this error
There are multiple ways to provoke your backend fail. For example, misconfigure your backend in Varnish or stop your backend.
You can filter and print specific messages from the varnishlog
in many ways.
The purpose of this exercise is to use the query option -q
, but you can also use the include tags option -i
or -I
and the grep
command.
Note
You can also use varnishtest
to provoke a Service Unavailable response and assert it by reading VSL with logexpect.
Uptime mgt: 1+23:38:08 Hitrate n: 10 100 438 Uptime child: 1+23:38:08 avg(n): 0.9967 0.5686 0.3870 NAME CURRENT CHANGE AVERAGE AVG_10 AVG_100 AVG_1000 MAIN.uptime 171488 1.00 1.00 1.00 1.00 1.00 MAIN.sess_conn 1055 7.98 . 8.35 4.49 2.11 MAIN.client_req 1055 7.98 . 8.35 4.49 2.11 MAIN.cache_hit 1052 7.98 . 8.35 4.49 2.10 MAIN.cache_miss 3 0.00 . 0.00 0.00 0.00 MAIN.backend_conn 4 0.00 . 0.00 0.00 0.01 MAIN.backend_toolate 3 0.00 . 0.00 0.00 0.01 MAIN.backend_recycle 4 0.00 . 0.00 0.00 0.01 MAIN.fetch_length 4 0.00 . 0.00 0.00 0.01 MAIN.pools 2 0.00 . 2.00 2.00 2.00 MAIN.threads 200 0.00 . 200.00 200.00 200.00 MAIN.threads_created 200 0.00 . 0.00 0.00 0.00 MAIN.n_object 1 0.00 . 1.00 0.85 0.81 MAIN.n_objectcore 3 0.00 . 3.00 2.85 2.81 MAIN.n_objecthead 4 0.00 . 4.00 3.89 3.83 MAIN.n_backend 1 0.00 . 1.00 1.00 1.00 MAIN.n_expired 2 0.00 . 2.00 1.76 1.33 MAIN.s_sess 1055 7.98 . 8.35 4.49 2.11 MAIN.s_req 1055 7.98 . 8.35 4.49 2.11 MAIN.s_fetch 3 0.00 . 0.00 0.00 0.00 MAIN.s_req_hdrbytes 122380 926.07 . 968.24 520.74 244.35 MAIN.s_resp_hdrbytes 376249 2854.04 2.00 2982.17 1602.59 751.87 MAIN.s_resp_bodybytes 3435094 25993.71 20.00 27177.59 14616.67 6858.74 MAIN.backend_req 4 0.00 . 0.00 0.00 0.01 MAIN.n_vcl 1 0.00 . 0.00 0.00 0.00 MAIN.bans 1 0.00 . 1.00 1.00 1.00 MAIN.n_gunzip 4 0.00 . 0.00 0.00 0.01 MAIN.cache_hit INFO Cache hits: Count of cache hits. A cache hit indicates that an object has been delivered to a client without fetching it from a backend server.
varnishstat
looks only at counters, which give a good representation of the general health of Varnish.
Counters, unlike the rest of the log, are not directly mapped to a single request, but represent how many times a specific action has occurred since Varnish started.
These counters are easily found in VSL, and are typically polled at reasonable interval to give the impression of real-time updates.
varnishstat
can be used to determine the request rate, memory usage, thread usage, number of failed backend connections, and more.
varnishstat
gives you information just about anything that is not related to a specific request.
There are over a hundred different counters available.
To increase the usefulness of varnishstat
, only counters with a value different from 0 are shown by default.
varnishstat
can be used interactively, or it can display the current values of all the counters with the -1
option.
Both methods allow you to specify specific counters using -f field1 -f field2 ..
to limit the list.
In interactive mode, varnishstat
has three areas.
The top area shows process uptime and hitrate information.
The center area shows a list of counter values.
The bottom area shows the description of the currently selected counter.
Hitrate n
and avg(n)
are related, where n is the number intervals.
avg(n)
measures the cache hit rate within n intervals.
The default interval time is one second.
You can configure the interval time with the -w
option.
Since there is no historical data of counters changes, varnishstat
has to compute the average while it is running.
Therefore, when you start varnishstat
, the values of Hitrate n
start at 1, then they increase to 10, 100 and 1000.
In the above example, the interval is one second.
The hitrate average avg(n)
show data for the last 10, 100, and 438 seconds.
The average hitrate is 0.9967 (or 99.67%) for the last 10 seconds, 0.5686 for the last 100 seconds and 0.3870 for the last 438 seconds.
In the above example, Varnish has served 1055 requests and is currently serving roughly 7.98 requests per second.
Some counters do not have "per interval" data, but are gauges with values that increase and decrease.
Gauges start with a g_
prefix.
Tip
You can also see many parameters in real-time graphs with the Varnish Administration Console (VAC).
Tip
If you need to collect statistics from more than a single Varnish server, Varnish Custom Statistics (VCS) allows you to do that. In addition, VCS allows you to define your metrics to collect and analyze aggregated statistics, for example:
- A/B testing
- Measuring click-through rate
- Track slow pages and cache misses
- Analyze what is "hot" right now in a news website
- Track changes in currency conversions in e-commerce
- Track changes in Stock Keeping Units (SKUs) behavior in e-commerce
- Track number of unique consumers of HLS/HDS/DASH video streams
Varnish provides a large number of counters for information and debugging purposes. Table 8 presents counters that are typically important. Other counters may be relevant only for Varnish developers when providing support.
Counters also provide feedback to Varnish developers on how Varnish works in production environments.
This feedback in turn allows Varnish to be developed according to its real usage.
Issue varnishstat -1
to list all counters with their current values.
Note
If you have many backends, consider to increase the size of the shared memory log.
For that, see the option -l
in the man page of varnishd
.
Tip
Remember that Varnish provides many reference manuals.
To see all Varnish counter field definitions, issue man varnish-counters
.
- Run
varnishstat
andvarnishlog
while performing a few requests. - See, analyze and understand how counters and parameters change in
varnishstat
andvarnishlog
.
varnishtest
.
If you are done with this exercise and have still time, try to assert some counters as described in Exercise: Assert Counters in varnishtest.This chapter is for the system administration course only
This section covers:
- Architecture
- Best practices
- Parameters
Perhaps the most important aspect of tuning Varnish is writing effective VCL code. For now, however, we will focus on tuning Varnish for your hardware, operating system and network. To be able to do that, knowledge of Varnish architecture is helpful.
It is important to know the internal architecture of Varnish for two reasons. First, the architecture is chiefly responsible for the performance, and second, it influences how you integrate Varnish in your own architecture.
There are several aspects of the design that were unique to Varnish when it was originally implemented. Truly good solutions, regardless of reusing ancient ideas or coming up with something radically different, is the aim of Varnish.
Figure 15 shows a block diagram of the Varnish architecture. The diagram shows the data flow between the principal parts of Varnish.
The main block is the Manager process, which is contained in the varnishd
binary program.
The task of the Manager process is to delegate tasks, including caching, to child processes.
The Manager process ensures that there is always a process for each task.
The main driver for these design decisions is security, which is explain at Security barriers in Varnish https://www.varnish-cache.org/docs/trunk/phk/barriers.html.
The Manager's command line interface (CLI) is accessible through:
1) varnishadm
as explained in The front-end varnishadm of the Varnish Command Line Interface (CLI) section,
2) the Varnish Agent vagent2, or
3) the Varnish Administration Console (VAC) (via vagent2)
The Varnish Agent vagent2 is an open source HTTP REST interface that exposes varnishd
services to allow remote control and monitoring.
vagent2 offers a web UI as shown in Figure 16, but you can write your own UI since vagent2 is an open interface.
Some features of vagent2 are:
- VCL uploading, downloading, persisting (storing to disk).
- parameter viewing, storing (not persisting yet)
- show/clear of panic messages
- start/stop/status of
varnishd
- banning
varnishstat
in JSON format
![ui/img/vagent2.png](/varnish/Varnish-Book/raw/master/ui/img/vagent2.png)
Figure :counter:`figure`: Varnish Agent's HTML interface; designed to showcase the various features of the Varnish Agent.
For more information about vagent2 and installation instructions, please visit https://github.com/varnish/vagent2.
Varnish Software has a commercial offering of a fully functional web UI called Varnish Administration Console (VAC). For more information about VAC, refer to the Varnish Administration Console (VAC) section.
The Manager process is owned by the root user, and its main functions are:
- apply configuration changes (from VCL files and parameters)
- delegate tasks to child processes: the Cacher and the VCL to C Compiler (VCC)
- monitor Varnish
- provide a Varnish command line interface (CLI)
- initialize the child process: the Cacher
The Manager checks every few seconds whether the Cacher is still there.
If the Manager does not get a reply within a given interval defined in ping_interval
, the Manager kills the Cacher and starts it up again.
This automatic restart also happens if the Cacher exits unexpectedly, for example, from a segmentation fault or assert error.
You can ping manually the cacher by executing varnishadm ping
.
Automatic restart of child processes is a resilience property of Varnish.
This property ensures that even if Varnish contains a critical bug that crashes the child, the child starts up again usually within a few seconds.
You can toggle this property using the auto_restart
parameter.
Note
Even if you do not perceive a lengthy service downtime, you should check whether the Varnish child is being restarted.
This is important, because child restarts introduce extra loading time as varnishd
is constantly emptying its cache.
Automatic restarts are logged into /var/log/syslog
.
To verify that the child process is not being restarted, you can also check its lifetime with the MAIN.uptime
counter in varnishstat
.
Varnish Software and the Varnish community at large occasionally get requests for assistance in performance tuning Varnish that turn out to be crash-issues.
Since the Cacher listens on public IP addresses and known ports, it is exposed to evil clients. Therefore, for security reasons, this child process is owned by an unprivileged user, and it has no backwards communication to its parent, the Manager.
The main functions of the Cacher are:
- listen to client requests
- manage worker threads
- store caches
- log traffic
- update counters for statistics
Varnish uses workspaces to reduce the contention between each thread when they need to acquire or modify memory.
There are multiple workspaces, but in Varnish 4 and later, the most important ones are workspace_client
and workspace_backend
.
Memory in workspace_client
is used to manipulate data at the frontend side of the Varnish state machine, i.e., request data.
workspace_backend
is used to manipulate data fetched from the backend side.
As an example, think about the memory needed to normalize an object's Host
header from www.example.com
to example.com
before it is stored in the cache.
If you have 5 MB of workspace and are using 1000 threads, the actual memory usage is not 5 GB. The virtual memory usage will indeed be 5GB, but unless you actually use the memory, this is not a problem. Your memory controller and operating system will keep track of what you actually use.
To communicate with the rest of the system, the child process uses the VSL accessible from the file system. This means that if a thread needs to log something, all it has to do is to grab a lock, write to a memory area and then free the lock. In addition to that, each worker thread has a cache for log-data to reduce lock contention. We will discuss more about the Threading Model later in this chapter.
The log file is usually about 80MB, and split in two. The first part is counters, the second part is request data. To view the actual data, a number of tools exist that parses the VSL.
Since the log data is not meant to be written to disk in its raw form, Varnish can afford to be very verbose. You then use one of the log-parsing tools to extract the piece of information you want -- either to store it permanently or to monitor Varnish in real-time.
If something goes wrong in the Cacher, it logs a detailed panic message to syslog
.
For testing, you can induce panic to varnishd
by issuing the command varnishadm debug.panic.worker
or by pressing the Induce Panic button in the Varnish Agent web interface.
Command to print VCL code compiled to C language and exit:
varnishd -C -f <vcl_filename>
Useful to check whether your VCL code compiles correctly.
Configuring the caching policies of Varnish is done in the Varnish Configuration Language (VCL).
Your VCL is then translated by the VCC process to C, which is compiled by a normal C compiler – typically gcc
, and linked into the running Varnish instance.
Since the VCL compilation is done outside of the child process, there is no risk of affecting the running Varnish instance by accidentally loading an ill-formatted VCL.
As a result, changing configuration while running Varnish is very cheap. Policies of the new VCL takes effect immediately. However, objects cached with an older configuration may persist until they have no more old references or the new configuration acts on them.
A compiled VCL file is kept around until you restart Varnish completely, or until you issue vcl.discard
from the management interface.
You can only discard compiled VCL files after all references to them are gone.
You can see the amount of VCL references by reading the parameter vcl.list
.
- The storage option
-s
defines the size of your cache and where it is stored - Use
varnishd -s
followed by one of the following methods to allocate space for the cache:malloc
file
persistent
(deprecated)mse
Varnish Massive Storage Engine (MSE) in Varnish Plus only
The -s <malloc[,size]>
option calls malloc()
to allocate memory space for every object that goes into the cache.
If the allocated space cannot fit in memory, the operating system automatically swaps the needed space to disk.
Varnish uses the jemalloc implementation. Although jemalloc emphasizes fragmentation avoidance, fragmentation still occurs. Jemalloc worst case of memory fragmentation is 20%, therefore, expect up to this percentage of additional memory usage. In addition to memory fragmentation you should consider an additional 5% overhead as described later in this section.
Another option is -s <file,path[,size[,granularity]]>
.
This option creates a file on a filesystem to contain the entire cache.
Then, the operating system maps the entire file into memory if possible.
The -s file
storage method does not retain data when you stop or restart Varnish!
For persistence, use the option -s persistent
.
The usage of this option, however, is strongly discouraged mainly because of consistency issues that might arise with it.
The Varnish Massive Storage Engine (MSE) option -s <mse,path[,path...]]>
is an improved storage method for Varnish Plus only.
MSE main improvements are decreased disk I/O load and lower storage fragmentation.
MSE is designed to store and handle over 100 TB with persistence, which makes it very useful for video on demand setups.
MSE uses a hybrid of two cache algorithms, least recently used (LRU) and least frequently used (LFU), to manage memory.
Benchmarks show that this algorithm outperforms malloc
and file
.
MSE also implements a mechanism to eliminate internal fragmentation.
The latest version of MSE requires a bookkeeping file. The size of this bookkeeping file depends on the cache size. Cache sizes in the order of gigabytes require a bookkeeping file of around 1% of the storage size. Cache sizes in the order of terabytes should have a bookkeeping file size around 0.5% of storage size.
For detailed instructions on how to configure MSE, please refer to the Varnish Plus documentation. For more details about its features and previous versions, please visit https://info.varnish-software.com/blog/varnish-mse-persistence.
When choosing storage backend, use malloc
if your cache will be contained entirely or mostly in memory.
If your cache will exceed the available physical memory, you have two options: file
or mse
.
We recommend you to use MSE because it performs much better than file
storage backend.
There is a storage overhead in Varnish, so the actual memory footprint of Varnish exceeds what the -s
argument specifies if the cache is full.
The current estimated overhead is 1kB per object.
For 1 million objects, that means 1GB extra memory usage.
This estimate might slightly vary between Varnish versions.
In addition to the overhead per object, Varnish requires memory to manage the cache and handle its own operation.
Our tests show that an estimate of 5% of overhead is accurate enough.
This overhead applies equally to malloc
, file
or mse
options.
For more details about memory usage in Varnish, please refer to https://info.varnish-software.com/blog/understanding-varnish-cache-memory-usage.
Note
As a rule of thumb use: malloc
if the space you want to allocate fits in memory, if not, use file
or mse
.
Remember that there is about 5% memory overhead and do not forget to consider the memory needed for fragmentation in malloc
or the disk space for the bookkeeping file in mse
.
- Avoid I/O operations
- Mount the shared memory log as tmpfs
- VSL is not persistent
The Varnish Shared memory Log (VSL), sometimes called shm-log or SHMLOG, is used to log most data.
VSL operates on a circular buffer.
Therefore, there is no a start or an end of it, but you can issue varnishlog -d
to see old log entries.
VSL is 80MB large by default and is not persistent, unless you instruct Varnish to do otherwise.
VSL is memory space mapped under /var/lib/varnish/
.
To change the size of the VSL, see the option -l
in the man page of varnishd
.
There is not much you have to do with the VSL, except ensure that it does not cause I/O operations.
You can avoid I/O by mounting the VSL as a temporary file storage (tmpfs).
This is typically configured in /etc/fstab
, and the shm-log is normally kept under /var/lib/varnish/
or equivalent locations.
You need to restart varnishd
after mounting it as tmpfs.
Warning
Some Varnish distribution setup the file storage backend option -s file
by default.
Those distribution set a path that puts the storage file in the same directory as the shm-log.
We discourage this practice.
In the CLI:
param.show -l
Do not fall for the copy/paste tips
Test the parameters in CLI, then store them in the configuration file
Varnish has many different parameters which can be adjusted to make
Varnish act better under specific workloads or with specific software and
hardware setups. They can all be viewed with param.show
in the
management interface varnishadm
.
You can set up parameters in two different ways.
In varnishadm
, use the command param.set <param> <value>
.
Alternatively, you can issue the command varnishd -p param=value
.
Remember that changes made in the management interface are not persistent. Therefore, unless you store your changes in a startup script, they will be lost when Varnish restarts.
The general advice with regards to parameters is to keep it simple. Most of the defaults are optimal. If you do not have a very specific need, it is generally better to use the default values.
A few debug commands exist in the CLI, which can be revealed with help -d
.
These commands are meant exclusively for development or testing, and many of them are downright dangerous.
Tip
Parameters can also be configured via the Varnish Administration Console (VAC) as shown in the figure below.
- The child process runs multiple threads in two thread pools
- Threads accept new connections and delegate them
- One worker threads per client request – it's common to use hundreds of worker threads
- Expire-threads evict old content from the cache
- Thread pools can safely be ignored
- Start threads better sooner than later
- Maximum and minimum values are per thread pool
When tuning Varnish, think about the expected traffic.
The most important thread setting is the number of cache-worker threads.
You may configure thread_pool_min
and thread_pool_max
.
These parameters are per thread pool.
Although Varnish threading model allows you to use multiple thread pools, we recommend you to do not modify this parameter. Based on our experience and tests, we have seen that 2 thread pools are enough. In other words, the performance of Varnish does not increase when adding more than 2 pools.
Note
If you run across the tuning advice that suggests to have a thread pool per CPU core, rest assured that this is old advice. We recommend to have at most 2 thread pools, but you may increase the number of threads per pool.
- Default values have proved to be sufficient in most cases
thread_pool_min
andthread_pool_max
are the most common threading parameters to tune.- Run extra threads to avoid creating them on demand
Varnish runs one thread per session, so the maximum number of threads is equal to the number of maximum sessions that Varnish can serve concurrently. If you seem to need more threads than the default, it is very likely that there is something wrong in your setup. Therefore, you should investigate elsewhere before you increase the maximum value.
You can observe if the default values are enough by looking at MAIN.sess_queued
through varnishstat
.
Look at the counter over time, because it is fairly static right after startup.
When tuning the number of threads, thread_pool_min
and thread_pool_max
are the most important parameters.
Values of these parameters are per thread pool.
The thread_pools
parameter is mainly used to calculate the total number of threads.
For the sake of keeping things simple, the current best practice is to leave thread_pools
at the default |def_thread_pools|.
Varnish operates with multiple pools of threads. When a connection is accepted, the connection is delegated to one of these thread pools. Afterwards, the thread pool either delegates the connection request to an available thread, queue the request otherwise, or drop the connection if the queue is full. By default, Varnish uses 2 thread pools, and this has proven sufficient for even the most busy Varnish server.
Varnish has the ability to spawn new worker threads on demand, and remove them once the load is reduced. This is mainly intended for traffic spikes. It's a better approach to keep a few threads idle during regular traffic, than to run on a minimum amount of threads and constantly spawn and destroy threads as demand changes. As long as you are on a 64-bit system, the cost of running a few hundred threads extra is very low.
The thread_pool_min
parameter defines how many threads run for each thread pool even when there is no load.
thread_pool_max
defines the maximum amount of threads that could be used per thread pool.
That means that with the minimum defaults |def_thread_pool_min| and |def_thread_pool_max| of minimum and maximums threads per pool respectively, you have:
- at least |def_thread_pool_min| * |def_thread_pools| worker threads at any given time
- no more than |def_thread_pool_max| * |def_thread_pools| worker threads ever
Warning
New threads use preallocated workspace, which should be enough for the required task.
If threads have not enough workspace, the child process is unable to process the task and it terminates.
To avoid this situation, evaluate your setup and consider to increase the workspace_client
or workspace_backend
parameter.
thread_pool_add_delay
: Wait at least this long after creating a thread.thread_pool_timeout
: Thread idle threshold.thread_pool_fail_delay
: After a failed thread creation, wait at least this long before trying to create another thread.
Varnish can use several thousand threads, and has had this capability from the very beginning.
However, not all operating system kernels were prepared to deal with this capability.
Therefore the parameter thread_pool_add_delay
was added to ensure that there is a small delay between each thread that spawns.
As operating systems have matured, this has become less important and the default value of thread_pool_add_delay
has been reduced dramatically,
from 20 ms to 2 ms.
There are a few, less important parameters related to thread timing.
The thread_pool_timeout
is how long a thread is kept around when there is no work for it before it is removed.
This only applies if you have more threads than the minimum, and is rarely changed.
Another less important parameter is the thread_pool_fail_delay
.
After the operating system fails to create a new thread, thread_pool_fail_delay
defines how long to wait for a re-trial.
As Varnish has matured, fewer and fewer parameters require tuning.
The workspace_client
and workspace_backend
are parameters that could still be relevant.
workspace_client
– incoming HTTP header workspace from the clientworkspace_backend
– bytes of HTTP protocol workspace for backend HTTP req/resp- Tune it if you have many big headers or have a VMOD that uses too much memory
- Remember: it is virtual, not physical memory
Workspaces are some of the things you can change with parameters. Sometimes you may have to increase them to avoid running out of workspace.
Theworkspace_client
parameter states how much memory can be allocated for each HTTP session. This space is used for tasks like string manipulation of incoming headers. Theworkspace_backend
parameter indicates how much memory can be allocated to modify objects returned from the backend. After an object is modified, its exact size is allocated and the object is stored read-only.
- As most of the parameters can be left unchanged, we will not go through all of them.
- You can take a look at the list of parameter by issuing
varnishadm param.show -l
to get information about what they can do.
The timeout-parameters are generally set to pretty good defaults, but you might have to adjust them for unusual applications.
The default value of connect_timeout
is |def_connect_timeout|.
This value is more than enough when having the Varnish server and the backend in the same server room.
Consider to increase the connect_timeout
value if your Varnish server and backend have a higher network latency.
Keep in mind that the session timeout affects how long sessions are kept around, which in turn affects file descriptors left open. It is not wise to increase the session timeout without taking this into consideration.
The cli_timeout
is how long the management thread waits for the worker thread to reply before it assumes it is dead, kills it and starts it back up.
The default value seems to do the trick for most users today.
Warning
If connect_timeout
is set too high, it does not let Varnish handle errors gracefully.
Note
Another use-case for increasing connect_timeout
occurs when virtual machines are involved as they can increase the connection time significantly.
Tip
More information in https://info.varnish-software.com/blog/understanding-timeouts-varnish-cache .
- Access a slow resource on the backend
- Set
first_byte_timeout
to 1 second - Check how Varnish times out the request to the backend
For the purpose of this exercise we use a CGI script that waits 5 seconds before responding:
http localhost/cgi-bin/sleep
To check how first_byte_timeout
impacts the behavior of Varnish, analyze the output of varnishlog
and varnishstat
.
Alternatively, you can use delay
in a mock-up backend in varnishtest
and assert VSL records and counters to verify the effect of first_byte_timeout
.
The subsection Solution: Tune first_byte_timeout and test it against mock-up server shows you how to do it.
- Change the
thread_pool_min
andthread_pool_max
parameters to get 10 threads running at any given time, but never more than 20. - Execute
varnishadm param.show <parameter>
to see parameter details.
These exercises are for educational purposes, and not intended as an encouragement to change the values.
You can learn from this exercise by using varnishstat
, varnishadm
and varnishstat
If you need help, see Solution: Configure Threading with varnishadm and varnishstat or Solution: Configure Threading with varnishtest.
This chapter is for the web-developer course only
This chapter covers:
- Protocol basics
- Requests and responses
- HTTP request/response control flow
- Statelessness and idempotence
- Cache related headers
- Hyper-Text Transfer Protocol, HTTP, is at the core of the web
- Specified by the IETF, there are two main versions: HTTP/1.1 and HTTP/2
- Varnish 4.0 supports HTTP/1.1
HTTP is a networking protocol for distributed systems. It is the foundation of data communication for the web. The development of this standard is done by the IETF and the W3C. In 2014, RFCs 723X were published to clarify HTTP/1.1 and they obsolete RFC 2616.
A new version of HTTP called HTTP/2 has been released under RFC 7540. HTTP/2 is an alternative to HTTP/1.1 and does not obsolete the HTTP/1.1 message syntax. HTTP's existing semantics remain unchanged.
The protocol allows multiple requests to be sent in serial mode over a single connection. If a client wants to fetch resources in parallel, it must open multiple connections.
- Resource: target of an HTTP request
- A resource may have different representations
- Representation: a particular instantiation of a resource
- A representation may have different states: past, current and desired
Each resource is identified by a Uniform Resource Identifier (URI), as described in Section 2.7 of [RFC7230].
A resource can be anything and such a thing can have different representations.
A representation is an instantiation of a resource.
An origin server, a.k.a. backend, produces this instantiation based on a list of request field headers, e.g., User-Agent
and Accept-encoding
.
When an origin server produces different representations of one resource, it includes a Vary
response header field.
This response header field is used by Varnish to differentiate between resource variations.
More details on this are in the Vary subsection.
An origin server might include metadata to reflect the state of a representation.
This metadata is contained in the validator header fields ETag
and Last-Modified
.
In order to construct a response for a client request, an algorithm is used to evaluate and select one representation with a particular state. This algorithm is implemented in Varnish and you can customize it in your VCL code. Once a representation is selected, the payload for a 200 (OK) or 304 (Not Modified) response can be constructed.
- A request is a message from a client to a server that includes the method to be applied to a requested resource, the identifier of the resource, the protocol version in use and an optional message body
- A method is a token that indicates the method to be performed on a URI
- Standard request methods are:
GET
,POST
,HEAD
,OPTIONS
,PUT
,DELETE
,TRACE
, orCONNECT
- Examples of URIs are
/img/image.png
or/index.html
- Header fields are allowed in requests and responses
- Header fields allow client and servers to pass additional information
- A response is a message from a server to a client that consists of a response status, headers and an optional message body
The first line of a request message is called Request-Line, whereas the first line of a response message is called Status-Line. The Request-Line begins with a method token, followed by the requested resource (URI) and the protocol version.
A request method informs the web server what sort of request this is:
Is the client trying to fetch a resource (GET
), update some data (POST
) at the backend, or just get the headers of a resource (HEAD
)?
Methods are case-sensitive.
After the Request-Line, request messages may have an arbitrary number of header fields.
For example: Accept-Language
, Cookie
, Host
and User-Agent
.
Message bodies are optional but they must comply to the requested method.
For instance, a GET
request should not contain a request body, but a POST
request may contain one.
Similarly, a web server cannot attach a message body to the response of a HEAD
request.
The Status-Line of a response message consists of the protocol version followed by a numeric status code and its associated textual phrase.
This associated textual phrase is also called reason.
Important is to know that the reason is intended for the human user.
That means that the client is not required to examine the reason, as it may change and it should not affect the protocol.
Examples of status codes with their reasons are: 200 OK
, 404 File Not Found
and 304 Not Modified
.
Responses also include header fields after the Status-Line, which allow the server to pass additional information about the response.
Examples of response header fields are: Age
, ETag
, Cache-Control
and Content-Length
.
Note
Requests and responses share the same syntax for headers and message body, but some headers are request- or response-specific.
GET / HTTP/1.1 Host: localhost User-Agent: Mozilla/5.0 (Macintosh; U; Intel Mac OS X 10.5; fr; rv:1.9.2.16) \ Gecko/20110319 Firefox/3.6.16 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: fr,fr-fr;q=0.8,en-us;q=0.5,en;q=0.3 Accept-Encoding: gzip,deflate Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive: 115 Connection: keep-alive Cache-Control: max-age=0
The above example is a typical HTTP request that includes a Request-Line, and headers, but no message body.
The Request-Line consists of the GET
request for the /
resource and the HTTP/1.1
version.
The request includes the header fields Host
, User-Agent
, Accept
, Accept-Language
, Accept-Encoding
, Accept-Charset
, Keep-Alive
, Connection
and Cache-Control
.
Note that the Host
header contains the hostname as seen by the browser.
The above request was generated by entering http://localhost/ in the browser.
Most browsers automatically add a number of headers.
Some of the headers will vary depending on the configuration and state of the client. For example, language settings, cached content, forced refresh, etc. Whether the server honors these headers will depend on both the server in question and the specific header.
The following is an example of an HTTP request using the POST
method, which includes a message body:
POST /accounts/ServiceLoginAuth HTTP/1.1 Host: www.google.com User-Agent: Mozilla/5.0 (Macintosh; U; Intel Mac OS X 10.5; fr; rv:1.9.2.16) \ Gecko/20110319 Firefox/3.6.16 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: fr,fr-fr;q=0.8,en-us;q=0.5,en;q=0.3 Accept-Encoding: gzip,deflate Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive: 115 Connection: keep-alive Referer: https://www.google.com/accounts/ServiceLogin Cookie: GoogleAccountsLocale_session=en;[...] Content-Type: application/x-www-form-urlencoded Content-Length: 288 ltmpl=default[...]&signIn=Sign+in&asts=
HTTP/1.1 200 OK Server: Apache/2.2.14 (Ubuntu) X-Powered-By: PHP/5.3.2-1ubuntu4.7 Cache-Control: public, max-age=86400 Last-Modified: Mon, 04 Apr 2011 04:13:41 +0000 Expires: Sun, 11 Mar 1984 12:00:00 GMT Vary: Cookie,Accept-Encoding ETag: "1301890421" Content-Type: text/html; charset=utf-8 Content-Length: 23562 Date: Mon, 04 Apr 2011 09:02:26 GMT X-Varnish: 1886109724 1886107902 Age: 17324 Via: 1.1 varnish Connection: keep-alive [data]
The example above is an HTTP response that contains a Status-Line, headers and message body.
The Status-Line consists of the HTTP/1.1
version, the status code 200
and the reason OK
.
The response status code informs the client (browser) whether the server understood the request and how it replied to it.
These codes are fully defined in https://tools.ietf.org/html/rfc2616#section-10, but here is an overview of them:
- 1xx: Informational – Request received, continuing process
- 2xx: Success – The action was successfully received, understood, and accepted
- 3xx: Redirection – Further action must be taken in order to complete the request
- 4xx: Client Error – The request contains bad syntax or cannot be fulfilled
- 5xx: Server Error – The server failed to fulfill an apparently valid request
- HTTP is a stateless protocol
- Common methods: safe, idempotent and cacheable
- Most common cacheable request methods are
GET
andHEAD
HTTP is by definition a stateless protocol meaning that each request message can be understood in isolation. Hence, a server MUST NOT assume that two requests on the same connection are from the same user agent unless the connection is secured and specific to that agent.
HTTP/1.1 persists connections by default.
This is contrary to most implementations of HTTP/1.0, where each connection is established by the client prior to the request and closed by the server after sending the response.
Therefore, for compatibility reasons, persistent connections may be explicitly negotiated as they are not the default behavior in HTTP/1.0 [https://tools.ietf.org/html/rfc7230#appendix-A.1.2].
In practice, there is a header called Keep-Alive
you may use if you want to control the connection persistence between the client and the server.
A method is "safe" if it is read-only; i.e., the client request does not alter any state on the server.
GET
, HEAD
, OPTIONS
, and TRACE
methods are defined to be safe.
An idempotent method is such that multiple identical requests have the same effect as a single request.
PUT
, DELETE
and safe requests methods are idempotent.
Cacheable methods are those that allow to store their responses for future reuse.
RFC7231 specifies GET
, HEAD
and POST
as cacheable.
However, responses from POST
are very rarely treated as cacheable.
[https://tools.ietf.org/html/rfc7231#section-4.2]
HTTP provides a list of headers fields to control cache behavior
The most important caching header fields are:
Expires
Cache-Control
Etag
Last-Modified
If-Modified-Since
If-None-Match
Vary
Age
A cached object is a local store of HTTP response messages. These objects are stored, controlled, retrieved and deleted by a subsystem, in this case Varnish. For this purpose, Varnish uses the caching header fields defined in https://tools.ietf.org/html/rfc7232 and https://tools.ietf.org/html/rfc7234.
If a matched cache is valid, Varnish constructs responses from caches. As a result, the origin server is freed from creating and transmitting identical response bodies.
When to serve a cached object?
- The cached object is properly matched: cache-hit
- The requested method and its matched object allows it
- The freshness of the cached object is acceptable
When Varnish matches a request with a cached object (aka cache-hit), it evaluates whether the cache or origin server should be used to construct the response. There are many rules that should be taken into consideration when validating a cache. Most of those rules use caching header fields.
This subsection describes first the concept of cache-hit and cache-miss.
After that, it describes three header fields commonly used to effectively match caches.
These fields are Vary
, Etag
and If-None-Match
.
- Cache-hits are used to reuse, update or invalidate caches
- Objects may have variants (
Vary
andEtag
)
Figure 19 shows the flow diagram of a cache-hit. A cache-hit occurs when the requested object (URI) matches a stored HTTP response message (cache). If the matched stored message is valid to construct a response for the client, Varnish serves construct a response and serves it without contacting the origin server.
Figure 20 shows the flow diagram of a cache-miss. A cache-miss happens when Varnish does not match a cache. In this case, Varnish forwards the request to the origin server.
- Selects a representation of a resource
- Be careful when using
Vary
- Wrong usage can create a very large number of cached objects and reduce efficiency
If the origin server sends Vary
in a response, Varnish does not use this response to satisfy a later request unless the later request has the same values for the listed fields in Vary
as the original request.
As a consequence, Vary
expands the cache key required to match a new request to the stored cache entry.
Vary
is one of the trickiest headers to deal with when caching.
A caching server like Varnish does not necessarily understand the semantics of a header, or what part triggers different variants of a response.
In other words, an inappropriate use of Vary
might create a very large number of cached objects, and reduce the efficiency of your cache server.
Therefore, you must be extremely cautious when using Vary
.
Caching objects taking into consideration all differences from requesters creates a very fine-grained caching policy.
This practice is not recommended, because those cached objects are most likely retrieved only by their original requester.
Thus, fine-grained caching strategies do not scale well.
This is a common mistake if Vary
is not used carefully.
An example of wrong usage of Vary
is setting Vary: User-Agent
.
This tells Varnish that for absolutely any difference in User-Agent
, the response from the origin server might look different.
This is not optimal because there are probably thousands of User-Agent strings out there.
Another example of bad usage is when using Vary: Cookie
to differentiate a response.
Again, there could be a very large number of cookies and hence a very large number of cached objects, which are going to be retrieved most likely only by their original requesters.
The most common usage of Vary
is Vary: Accept-Encoding
, which tells Varnish that the content might look different depending on the request Accept-Encoding
header.
For example, a web page can be delivered compressed or uncompressed depending on the client.
For more details on how to use Vary
for compressions, refer to https://www.varnish-cache.org/docs/trunk/users-guide/compression.html.
One way to assist Vary
is by building the response body from cached and non-cached objects.
We will discuss this further in the Content Composition chapter.
Varnish Test Cases (VTC) in varnishtest
can also help you to understand and isolate the behavior of Vary
.
For more information about it, refer to the subsection Understanding Vary in varnishtest.
Note
Varnish can handle Accept-Encoding
and Vary: Accept-Encoding
, because Varnish has support for gzip compression.
- An Entity Tag (
ETag
) is metadata to differentiate between multiple states of a resource's representation - A differentiator key of presentations in addition to
Vary
- An
ETag
is a validator header field - Response header field
Origin servers normally add metadata to further describe the representation of a resource.
This metadata is used in conditional requests.
"Conditional requests are HTTP requests that include one or more header fields indicating a precondition to be tested before applying the method semantics to the target resource" [RFC7232].
ETag
is a validator header field.
The ETag
header field provides a state identifier for the requested variant (resource representation).
ETags
are used to differentiate between multiple states based on changes over time of a representation.
In addition, ETags
are also used differentiate between multiple representations based on content negotiation regardless their state.
Example of an ETag header:
ETag: "1edec-3e3073913b100"
The response ETag
field is validated against the request If-None-Match
header field.
We will see the details of If-None-Match
later in this subsection, but before, we learn about the other validator header field: Last-Modified
.
- Time-based state of presentations
- Validator header field
- Response header field
The Last-Modified
response header field is a timestamp that indicates when the variant was last modified.
This headers may be used in conjunction with If-Modified-Since
and If-None-Match
.
Example of a Last-Modified
header:
Last-Modified: Wed, 01 Sep 2004 13:24:52 GMT
ETag
and Last-Modified
are validator header fields, which help to differentiate between representations.
Normally, origin servers send both fields in successful responses.
Whether you use one, another or both, depends on your use cases.
Please refer to Section 2.4 in https://tools.ietf.org/html/rfc7232#section-2.4 for a full description on when to use either of them.
- Precondition Header Field
- Request header field
- Validates local caches against
ETag
A client that has obtained a response message and stored it locally, may reuse the obtained ETag
value in future requests to validate its local cache against the selected cache in Varnish.
The obtained value from an ETag
is sent from the client to Varnish in the request If-None-Match
header field.
In fact, a client may have stored multiple resource representations and therefore a client may send an If-None-Match
field with multiple ETag
values to validate.
The purpose of this header field is to reuse local caches without compromising its validity. If the local cache is valid, Varnish replies with a 304 (Not Modified) response, which does not include a message body. In this case, the client reuses its local cache to construct the requested resource.
Example of an If-None-Match header:
If-None-Match: "1edec-3e3073913b100"
- Validates local caches by modification date
- Precondition Header Field
- Request header field
A request containing an If-Modified-Since
header field indicates that the client wants to validate one or more of its local caches by modification date.
If the requested representation has not been modified since the time specified in this field, Varnish returns a 304 (not modified) response.
A 304 response does not contain message body.
This behavior is similar to as when using If-None-Match
.
Example of an If-Modified-Since header:
If-Modified-Since: Wed, 01 Sep 2004 13:24:52 GMT
Tip
The subsection Understanding Last-Modified and If-Modified-Since in varnishtest explains further these concepts with a practical VTC example.
- How to control which caches can be served?
Cache-Control
andPragma
(for backwards compatibility only)
no-cache
directive.
This subsection reviews two common header fields, Cache-Control
and Pragma
, to check caching allowance.The Cache-Control
header field specifies directives that must be applied by all caching mechanisms (from proxy cache to browser cache).
Table 12 summarizes the directives you may use for each context.
The most relevant directives of Cache-Control
are:
public
: The response may be cached by any cache.no-store
: The response body must not be stored by any cache mechanism.no-cache
: Authorizes a cache mechanism to store the response in its cache but it must not reuse it without validating it with the origin server first.- In order to avoid any confusion with this argument think of it as a "store-but-do-no-serve-from-cache-without-revalidation" instruction.
max-age
: Specifies the period in seconds during which the cache is considered fresh.s-maxage
: Likemax-age
but it applies only to public caches.
Example of a Cache-Control
header:
Cache-Control: public, max-age=2592000
A more hands-on explanation as VTC can be found in the subsection Understanding Cache-Control in varnishtest.
Note
Cache-Control always overrides Expires.
Note
By default, Varnish does not care about the Cache-Control
request header.
If you want to let users update the cache via a force refresh you need to do it yourself.
- Only for legacy
- Treat
Pragma: no-cache
asCache-Control: no-cache
Pragma
request header is a legacy header and should no longer be used.
Some applications still send headers like Pragma: no-cache
but this is for backwards compatibility reasons only.
Any proxy cache should treat Pragma: no-cache
as Cache-Control: no-cache
, and should not be seen as a reliable header especially when used as a response header.- Fresh object: age has not yet exceeded its freshness lifetime
- Stale object: has exceeded its freshness lifetime, i.e., expired object
When reusing a stored response (cached object), you should always check its freshness and evaluate whether to deliver expired objects or not. A response's freshness lifetime is the length of time between its generation by the origin server and its expiration time. A stale (expired) object can also be reused, but only after further validation with the origin server.
As defined in RFC7234 [https://tools.ietf.org/html/rfc7234#section-4.2]:
A response's age is the time that has passed since it was generated by, or successfully validated with, the origin server. The primary mechanism for determining freshness is for an origin server to provide an explicit expiration time in the future, using either the ``Expires`` header field or the ``max-age`` response directive.
- Response header field calculated at the cache server, i.e., Varnish
- Varnish sends an additional response header field,
Age
, to indicate the age of the cache - Clients (and Varnish) will use the
Age
header field to determine the freshness of a cache max-age
-based equation:cache duration = max-age - Age
Age
can be used to disallow caches at the client side
Consider what happens if you let Varnish cache content for a week.
If Varnish does not calculate the age of a cached object, Varnish might happily inform clients that the content is fresh, but the cache could be older than the maximum allowed max-age
.
By age we mean an estimate amount of time since the response was generated or successfully validated at the origin server.
Client browsers calculate a cache duration based on the Age
header field and the max-age
directive from Cache-Control
.
If this calculation results in a negative number, the browser does not cache the response locally.
Negative cache duration times, however, do not prevent browsers from using the received object.
Varnish does the same, if you put one Varnish server in front of another.
- Copy
article.php
fromVarnish-Book/material/webdev/
to/var/www/html/
- Send a request to article.php via Varnish, and see the response
Age
header field invarnishlog -g request -i ReqHeader,RespHeader
- Click the link several times and refresh your browser. Can you identify patterns?
- Analyze the output of
varnishstat -f MAIN.client_req -f MAIN.cache_*
in addition tovarnishlog
- Can you use the
Age
field to determine whether Varnish made a cache hit? - What is the difference between caching time in Varnish and the client?
- Use different browsers and analyze whether their internal caches work different
You might encounter that different browsers have different behaviors. Some of them might cache content locally, and their behavior when refreshing might be different, which can be very confusing. This just highlights that Varnish is not the only part of your web-stack that parses and honors cache-related headers. There might also be other caches along the way which you do not control, like a company-wide proxy server.
Since browsers might interpret cache headers differently, it is a good idea to control them in your cache server. In the next chapters, you will learn how to modify the response headers Varnish sends. This also allows your origin server to emit response headers that should be seen and used by Varnish only, not in your browser.
When browsers decide to load a resource from their local cache, requests are never sent.
Therefore this exercise and these type of tests are not possible to be simulated in varnishtest
.
- Used to stale objects
- Response header field only
The Expires
response header field gives the time after which the response is considered stale.
Normally, a stale cache item should not be returned by any cache (proxy cache or client cache).
The syntax for this header is:
Expires: GMT formatted date
It is recommended not to define Expires
too far in the future.
Setting it to 1 year is usually enough.
The use of Expires
does not prevent the cached object from being updated.
For example, if the name of the resource is updated.
Expires
and Cache-Control
do more or less the same job, but Cache-Control
gives you more control.
The most significant differences between these two headers is:
Cache-Control
uses relative times in secondsCache-Control
is both a request and a response header field.Expires
always returns an absolute timeExpires
is a response header field only
Tip
To learn more about the behavior of Expires
, refer to the subsection Understanding Expires in varnishtest.
Against a real backend:
- Use httpheadersexample.php via your Varnish server to experiment and get a sense of what it is all about.
- Copy the PHP file from
Varnish-Book/material/webdev/
to/var/www/html/
- Use
varnishstat -f MAIN.client_req -f MAIN.cache_hit
andvarnishlog -g request -i ReqHeader,RespHeader
to analyze the responses. - Try every link several times by clicking on them and refreshing your browser.
- Analyze the response in your browser and the activity in your Varnish server.
- Discuss what happens when having the
Cache-Control
andExpires
fields in the third link. - When testing
Last-Modified
andIf-Modified-Since
, does your browser issue a request to Varnish? If the item was in cache, does Varnish query the origin server? - Try the
Vary
header field from two different browsers.
varnishlog
, varnishstat
and another browser, or use client mock-ups in varnishtest
instead of browsers.In this chapter, you will learn the following topics:
- The Varnish Configuration Language (VCL) is a domain-specific language
- VCL as a finite state machine
- States as subroutines
- Varnish includes built-in subroutines
- Available functions, legal return actions and variables
The Varnish Configuration Language (VCL) is a domain-specific language designed to describe request handling and document caching policies for Varnish Cache.
When a new configuration is loaded, the VCC process, created by the Manager process, translates the VCL code to C.
This C code is compiled typically by gcc
to a shared object.
The shared object is then loaded into the cacher process.
This chapter focuses on the most important tasks to write effective VCL code.
For this, you will learn the basic syntax of VCL, and the most important VCL built-in subroutines: vcl_recv
and vcl_backend_response
.
All other built-in subroutines are taught in the next chapter.
Tip
Remember that Varnish has many reference manuals.
For more details about VCL, check its manual page by issuing man vcl
.
- VCL workflow seen as a finite state machine – See Figure 23 in the book
- States are conceptualized and implemented as subroutines, e.g.,
sub vcl_recv
- Built-in subroutines start with
vcl_
, which is a reserved prefix return (action)
terminates subroutines, whereaction
is a keyword that indicates the next step to do
Snippet from vcl_recv subroutine
VCL is often described as a finite state machine.
Each state has available certain parameters that you can use in your VCL code.
For example: response HTTP headers are only available after vcl_backend_fetch
state.
Figure 23 shows a simplified version of the Varnish finite state machine. This version shows by no means all possible transitions, but only a typical set of them. Figure 24 and Figure 25 show the detailed version of the state machine for the frontend and backend worker respectively.
States in VCL are conceptualized as subroutines, with the exception of the waiting state described in Waiting State
Subroutines in VCL take neither arguments nor return values.
Each subroutine terminates by calling return (action)
, where action
is a keyword that indicates the desired outcome.
Subroutines may inspect and manipulate HTTP header fields and various other aspects of each request.
Subroutines instruct how requests are handled.
Subroutine example:
sub pipe_if_local { if (client.ip ~ local) { return (pipe); } }
To call a subroutine, use the call
keyword followed by the subroutine's name:
call pipe_if_local;
Varnish has built-in subroutines that are hook into the Varnish workflow.
These built-in subroutines are all named vcl_*
.
Your own subroutines cannot start their name with vcl_
.
- Figure 24 shows the detailed request flow diagram of the backend worker.
- The grayed box is detailed in Figure 25.
- Each request is processed separately
- Each request is independent from others at any given time
- States are related, but isolated
return(action);
exits the current state and instructs Varnish to proceed to the next state- Built-in VCL code is always present and appended below your own VCL
Before we begin looking at VCL code, we should learn the fundamental concepts behind VCL. When Varnish processes a request, it starts by parsing the request itself. Later, Varnish separates the request method from headers, verifying that it is a valid HTTP request and so on. When the basic parsing has completed, the very first policies are checked to make decisions.
Policies are a set of rules that the VCL code uses to make a decision.
Policies help to answer questions such as: should Varnish even attempt to find the requested resource in the cache?
In this example, the policies are in the vcl_recv
subroutine.
Warning
If you define your own subroutine and execute return (action);
in it, control is passed to the Varnish Run Time (VRT) environment.
In other words, your return (action);
skips the built-it subroutine.
- VCL files start with
vcl 4.0;
- //, # and /* foo */ for comments
- Subroutines are declared with the
sub
keyword - No loops, state-limited variables
- Terminating statements with a keyword for next action as argument of the
return()
function, i.e.:return(action)
- Domain-specific
include "foo.vcl";
to include a VCL fileimport foo;
to load Varnish modules (VMODs)
Starting with Varnish 4.0, each VCL file must start by declaring its version with a special vcl 4.0;
marker at the top of the file.
If you have worked with a programming language or two before, the basic syntax of Varnish should be reasonably straightforward.
VCL is inspired mainly by C and Perl.
Blocks are delimited by curly braces, statements end with semicolons, and comments may be written as in C, C++ or Perl according to your own preferences.
Subroutines in VCL neither take arguments, nor return values. Subroutines in VCL can exchange data only through HTTP headers.
VCL has terminating statements, not traditional return values.
Subroutines end execution when a return(*action*)
statement is made.
The action tells Varnish what to do next.
For example, "look this up in cache", "do not look this up in the cache", or "generate an error message".
To check which actions are available at a given built-in subroutine, see the Legal Return Actions section or see the manual page of VCL.
VCL has two directives to use contents from another file.
These directives are include
and import
, and they are used for different purpose.
include
is used to insert VCL code from another file.
Varnish looks for files to include in the directory specified by the vcl_dir
parameter of varnishd
.
Note the quotation marks in the include
syntax.
import
is used to load VMODs and make available their functions into your VCL code.
Varnish looks for VMODs to load in the directory specified by the vmod_dir
parameter of varnishd
.
Note the lack of quotation marks in the import
syntax.
You can use the include
and import
in varnishtest
.
To learn more on how to test your VCL code in a VTC, refer to the subsection VCL in varnishtest.
Functions:
regsub(str, regex, sub)
regsuball(str, regex, sub)
ban(boolean expression)
hash_data(input)
synthetic(str)
Keywords:
call subroutine
return(action)
new
set
unset
All functions are available in all subroutines, except the listed in the table below.
VCL offers many simple to use built-in functions that allow you to modify strings, add bans, restart the VCL state engine and return control to the Varnish Run Time (VRT) environment. This book describes the most important functions in later sections, so the description at this point is brief.
regsub()
and regsuball()
take a string str
as input, search it with a regular-expression regex
and replace it with another string.
regsub()
changes only the first match, and `regsuball()
changes all occurrences.
The ban(boolean expression)
function invalidates all objects in cache that match the boolean expression.
banning and purging in detailed in the Cache Invalidation chapter.
The table above shows the VCL built-in subroutines and their legal returns.
return
is a built-in keyword that ends execution of the current VCL subroutine and continue to the next action
step in the request handling state machine.
Legal return actions are: lookup, synth, purge, pass, pipe, fetch, deliver, hash, restart, retry, and abandon.
Note
In Varnish 4 purge
is used as a return action.
Table 17 shows the availability of variables in each VCL subroutine and whether the variables are readable (R) or writable (W).
The variables in this table are listed per subroutine and follow the prefix req.
, bereq.
, beresp.
, obj.
, or resp.
.
However, predefined variables does not strictly follow the table, for example, req.restarts
is readable but not writable.
In order to see the exact description of predefined variables, consult the VCL man page or ask your instructor.
Most variables are self-explanatory but not how they influence each other, thus a brief explanation follows:
Values of request (req.
) variables are automatically assigned to backend request (bereq.
) variables.
However, those values may slightly differ, because Varnish may modify client requests.
For example, HEAD
requests coming from clients may be converted to GET
requests towards the backend.
Changes in backend response (beresp.
) variables affect response (resp.
) and object (obj.
) variables.
Many of the obj.
variables are set in resp.
, which are to be sent to the clients.
Additional variable prefixes from Table 17 are; client.
, server.
, local
, remote
, and storage.
.
These prefixes are accessible from the subroutines at the frontend (client) side.
Yet another variable is now
, which is accessible from all subroutines.
Support for global variables with a lifespan across transactions and VCLs is achieved with the variable VMOD. This VMOD keeps the variables and its values as long as the VMOD is loaded. Supported data types are strings, integers and real numbers. For more information about the variable VMOD, please visit https://github.com/varnish/varnish-modules/blob/master/docs/vmod_var.rst.
Note
Recall that every transaction in Varnish is always in a state, and each state is represented by its correspondent subroutine.
- We will revisit
vcl_recv
after we learn more about built-in functions, keywords, variables and return actions
The built-in VCL for vcl_recv
is designed to ensure a safe caching policy even with no modifications in VCL.
It has two main uses:
- Only handle recognized HTTP methods.
- Cache requests with
GET
andHEAD
headers.
Policies for no caching data are to be defined in your VCL.
Built-in VCL code is executed right after any user-defined VCL code, and is always present.
You can not remove built-in subroutines, however, you can avoid them if your VCL code reaches one of the terminating actions: pass
, pipe
, hash
, or synth
.
These terminating actions return control from the VRT (Varnish Run-Time) to Varnish.
For a well-behaving Varnish server, most of the logic in the built-in VCL is needed. Consider either replicating all the built-in VCL logic in your own VCL code, or let your client requests be handled by the built-in VCL code.
We will revisit and discuss in more detail the vcl_recv
subroutine in VCL Built-in Subroutines
, but before, let's learn more about built-in functions, keywords, variables and return actions
- Find and open the
built-in.vcl
code, and analyze thevcl_recv
subroutine - Create your VCL code to avoid caching all URLs under
/admin
- Compile your VCL code to C language, and analyze how the
built-in.vcl
code is appended
- See Figure 25 in the book
- Review of return actions:
fetch
,deliver
,retry
andabandon
Figure 25 shows the vcl_backend_fetch
, vcl_backend_response
and vcl_backend_error
subroutines.
These subroutines are the backend-counterparts to vcl_recv
.
You can use data provided by the client in vcl_recv
or even vcl_backend_fetch
to define your caching policy.
An important difference is that you have access to bereq.*
variables in vcl_backend_fetch
.
As detailed in Legal Return Actions, vcl_backend_fetch
can return fetch
or abandon
, vcl_backend_response
can return deliver
, retry
or abandon
, and vcl_backend_error
can return deliver
or retry
.
The fetch
action transmits the request to the backend.
The abandon
action discards any possible response from the backend.
The deliver
action builds a response with the response from the backend and send it to the client.
An important difference between deliver
and abandon
is that deliver
stores the response in the cache, whereas abandon
does not.
You can leverage this difference with stale objects.
For example, in 5xx
server error, you might want to build a response with an stale object instead of sending the error to the client.
The retry
action re-enters vcl_backend_fetch
as further detailed in retry Return Action.
The functionality of these return actions are the same for the subroutines where they are valid.
You will learn more about vcl_backend_fetch
in the next chapter, but before we review vcl_backend_response
because the backend response is normally processed there.
- Override cache time for certain URLs
- Strip
Set-Cookie
header fields that are not needed - Strip buggy
Vary
header fields - Add helper-headers to the object for use in banning (more information in later sections)
- Sanitize server response
- Apply other caching policies
Figure 25 shows that vcl_backend_response
may terminate with one of the following actions: deliver
, retry
and abandon
.
The deliver
terminating action may or may not insert the object into the cache depending on the response of the backend.
The retry
action makes Varnish to transmit the request to the backend again by calling the vcl_backend_fetch
subroutine.
The abandon
action discards any response from the backend.
Backends might respond with a 304
HTTP headers.
304
responses happen when the requested object has not been modified since the timestamp If-Modified-Since
in the HTTP header.
If the request hits a non fresh object (see Figure 2), Varnish adds the If-Modified-Since
header with the value of t_origin
to the request and sends it to the backend.
304
responses do not contain a message body.
Thus, Varnish builds the response using the body from cache.
304
responses update the attributes of the cached object.
built-in vcl_backend_response
The vcl_backend_response
built-in subroutine is designed to avoid caching in conditions that are most probably undesired.
For example, it avoids caching responses with cookies, i.e., responses with Set-Cookie
HTTP header field.
This built-in subroutine also avoids request serialization described in the Waiting State section.
To avoid request serialization, beresp.uncacheable
is set to true
, which in turn creates a hit-for-pass
object.
The hit-for-pass section explains in detail this object type.
If you still decide to skip the built-in vcl_backend_response
subroutine by having your own and returning deliver
, be sure to never set beresp.ttl
to 0
.
If you skip the built-in subroutine and set 0
as TTL value, you are effectively removing objects from cache that could eventually be used to avoid request serialization.
Note
Varnish 3.x has a hit_for_pass return action.
In Varnish 4, this action is achieved by setting beresp.uncacheable
to true
.
The hit-for-pass section explains this in more detail.
Before Varnish runs vcl_backend_response
, the beresp.ttl
variable has already been set to a value.
beresp.ttl
is initialized with the first value it finds among:
- The
s-maxage
variable in theCache-Control
response header field - The
max-age
variable in theCache-Control
response header field - The
Expires
response header field - The
default_ttl
parameter.
Only the following status codes will be cached by default:
- 200: OK
- 203: Non-Authoritative Information
- 300: Multiple Choices
- 301: Moved Permanently
- 302: Moved Temporarily
- 304: Not modified
- 307: Temporary Redirect
- 410: Gone
- 404: Not Found
You can cache other status codes than the ones listed above, but you have to set the beresp.ttl
to a positive value in vcl_backend_response
.
Since beresp.ttl
is set before vcl_backend_response
is executed, you can modify the directives of the Cache-Control
header field without affecting beresp.ttl
, and vice versa.
Cache-Control
directives are defined in RFC7234 Section 5.2.
A backend response may include the response header field of maximum age for shared caches s-maxage
.
This field overrides all max-age
values throughout all Varnish servers in a multiple Varnish-server setup.
For example, if the backend sends Cache-Control: max-age=300, s-maxage=3600
, all Varnish installations will cache objects with an Age
value less or equal to 3600 seconds.
This also means that responses with Age
values between 301 and 3600 seconds are not cached by the clients' web browser, because Age
is greater than max-age
.
A sensible approach is to use the s-maxage
directive to instruct Varnish to cache the response.
Then, remove the s-maxage
directive using regsub()
in vcl_backend_response
before delivering the response.
In this way, you can safely use s-maxage
as the cache duration for Varnish servers, and set max-age
as the cache duration for clients.
Warning
Bear in mind that removing or altering the Age
response header field may affect how responses are handled downstream.
The impact of removing the Age
field depends on the HTTP implementation of downstream intermediaries or clients.
For example, imagine that you have a three Varnish-server serial setup.
If you remove the Age
field in the first Varnish server, then the second Varnish server will assume Age=0
.
In this case, you might inadvertently be delivering stale objects to your client.
Set-Cookie
field are not cached.The purpose of the above example is to allow a gradual migration to using a backend-controlled caching policy.
If the backend does not supply s-maxage
, and the URL is a jpg file, then Varnish sets beresp.ttl
to 60 seconds.
The Cache-Control
response header field can contain a number of directives.
Varnish parses this field and looks for s-maxage
and max-age
.
By default, Varnish sets beresp.ttl
to the value of s-maxage
if found.
If s-maxage
is not found, Varnish uses the value max-age
.
If neither exists, Varnish uses the Expires
response header field to set the TTL.
If none of those header fields exist, Varnish uses the default TTL, which is 120 seconds.
The default parsing and TTL assignment are done before vcl_backend_response
is executed.
The TTL changing process is recorded in the TTL
tag of varnishlog
.
- Write a VCL which avoids caching the index page at all
- Your VCL should cover both resource targets: / and /index.html
When trying this out, remember that Varnish keeps the Host
header field in req.http.host
and the requested resource in req.url
.
For example, in a request to http://www.example.com/index.html, the http:// part is not seen by Varnish at all, req.http.host
has the value www.example.com and req.url
the value /index.html.
Note how the leading /
is included in req.url
.
If you need help, see Solution: Avoid caching a page.
Write a VCL that:
- uses
Cache-Control: s-maxage
when present, - caches
.jpg
for 30 seconds ifs-maxage
is not present, - caches
.html
for 10 seconds ifs-maxage
isn't present, and - removes the
Set-Cookie
header field ifs-maxage
or the above rules indicate that Varnish should cache.
If you need help, see Solution: Either use s-maxage or set TTL by file type.
Tip
Divide and conquer! Most somewhat complex VCL tasks are easily solved when you divide the tasks into smaller problems and solve them individually. Try solving each part of the exercise by itself first.
Note
Varnish automatically parses s-maxage
for you, so you only need to check if it is there or not.
Remember that if s-maxage
is present, Varnish has already used it to set beresp.ttl
.
- Request serialization is a non desired side-effect that is handled in the vcl_backend_response subroutine
- Designed to improve response performance
The waiting state is reached when a request n arrives while a previous identical request 0 is being handled at the backend. In this case, request 0 is set as busy and all subsequent requests n are queued in a waiting list. If the fetched object from request 0 is cacheable, all n requests in the waiting list call the lookup operation again. This retry will hopefully hit the desired object in cache. As a result, only one request is sent to the backend.
The waiting state is designed to improve response performance. However, a counterproductive scenario, namely request serialization, may occur if the fetched object is uncacheable, and so is recursively the next request in the waiting list. This situation forces every single request in the waiting list to be sent to the backend in a serial manner. Serialized requests should be avoided because their performance is normally poorer than sending multiple requests in parallel. The built-in vcl_backend_response subroutine avoids request serialization.
- VCL is all about policies
- Built-in VCL subroutines map the Varnish finite state machine
- Each request is handled independently
- Recommendation: Building a VCL file is done one line at a time
VCL provides subroutines that allow you to affect the handling of any single request almost anywhere in the execution chain. This provides pros and cons as any other programming language.
This book is not a complete reference guide to how you can deal with every possible scenario in VCL, but if you master the basics of VCL you can solve complex problems that nobody has thought about before. And you can usually do it without requiring too many different sources of documentation.
Whenever you are working on VCL, you should think of what that exact line you are writing has to do. The best VCL is built by having many independent sections that do not interfere with each other more than what they have to.
Remember that there is a built-in VCL.
If your own VCL code does not reach a return statement, the built-in VCL subroutine is executed after yours.
If you just need a little modification of a subroutine, you can use the code from {varnish-source-code}/bin/varnishd/builtin.vcl
as a template.
- Typical subroutines to customize:
vcl_recv
,vcl_pass
,vcl_backend_fetch
,vcl_backend_response
,vcl_hash
,vcl_hit
,vcl_miss
,vcl_deliver
, andvcl_synth
- If your VCL subroutine does return, you skip the built-in VCL subroutine
- The built-in VCL subroutines are always appended to yours
This chapter covers the VCL subroutines where you customize the behavior of Varnish. VCL subroutines can be used to: add custom headers, change the appearance of the Varnish error message, add HTTP redirect features in Varnish, purge content, and define what parts of a cached object is unique. After this chapter, you should know where to add your custom policies and you will be ready to dive into more advanced features of Varnish and VCL.
Note
It is strongly advised to let the default built-in subroutines whenever is possible. The built-in subroutines are designed with safety in mind, which often means that they handle any flaws in your VCL code in a reasonable manner.
Tip
Looking at the code of built-in subroutines can help you to understand how to build your own VCL code.
Built-in subroutines are in the file /usr/share/doc/varnish/examples/builtin.vcl.gz
or {varnish-source-code}/bin/varnishd/builtin.vcl
.
The first location may change depending on your distro.
- Normalize client input
- Pick a backend web server
- Re-write client-data for web applications
- Decide caching policy based on client input
- Access Control Lists (ACL)
- Security barriers, e.g., against SQL injection attacks
- Fixing mistakes, e.g.,
index.htlm
->index.html
vcl_recv
is the first VCL subroutine executed, right after Varnish has parsed the client request into its basic data structure.
vcl_recv
has four main uses:
- Modifying the client data to reduce cache diversity. E.g., removing any leading "www." in the
Host:
header. - Deciding which web server to use.
- Deciding caching policy based on client data. For example; no caching POST requests but only caching specific URLs.
- Executing re-write rules needed for specific web applications.
In vcl_recv
you can perform the following terminating actions:
pass: It passes over the cache lookup, but it executes the rest of the Varnish request flow. pass does not store the response from the backend in the cache.
pipe: This action creates a full-duplex pipe that forwards the client request to the backend without looking at the content. Backend replies are forwarded back to the client without caching the content. Since Varnish does no longer try to map the content to a request, any subsequent request sent over the same keep-alive connection will also be piped. Piped requests do not appear in any log.
hash: It looks up the request in cache.
purge: It looks up the request in cache in order to remove it.
synth - Generate a synthetic response from Varnish. This synthetic response is typically a web page with an error message. synth may also be used to redirect client requests.
It's also common to use vcl_recv
to apply some security measures.
Varnish is not a replacement for intrusion detection systems, but can still be used to stop some typical attacks early.
Simple Access Control Lists (ACLs) can be applied in vcl_recv
too.
For further discussion about security in VCL, take a look at the Varnish Security Firewall (VSF) application at https://github.com/comotion/VSF. The VSF supports Varnish 3 and above. You may also be interested to look at the Security.vcl project at https://github.com/comotion/security.vcl. The Security.vcl project, however, supports only Varnish 3.x.
Tip
The built-in vcl_recv
subroutine may not cache all what you want, but often it's better not to cache some content instead of delivering the wrong content to the wrong user.
There are exceptions, of course, but if you can not understand why the default VCL does not let you cache some content, it is almost always worth it to investigate why instead of overriding it.
One way of serving different content for mobile devices and desktop browsers is to run some simple parsing on the User-Agent header. The following VCL code is an example to create custom headers. These custom headers differentiate mobile devices from desktop computers.
You can read more about different types of device detection at https://www.varnish-cache.org/docs/trunk/users-guide/devicedetection.html
This simple VCL will create a request header called X-Device which will contain either mobile
or desktop
.
The web server can then use this header to determine what page to serve, and inform Varnish about it through Vary: X-Device
.
It might be tempting to just send Vary: User-Agent
, but that requires you to normalize the User-Agent header itself because there are many tiny variations in the description of similar User-Agents.
This normalization, however, leads to loss of detailed information of the browser.
If you pass the User-Agent header without normalization, the cache size may drastically inflate because Varnish would keep possibly hundreds of different variants per object and per tiny User-Agent variants.
For more information on the Vary
HTTP response header, see the Vary section.
Note
If you do use Vary: X-Device
, you might want to send Vary: User-Agent
to the users after Varnish has used it.
Otherwise, intermediary caches will not know that the page looks different for different devices.
- Copy the
Host
header field (req.http.Host
) and URL (req.url
) to two new request headers:req.http.x-host
andreq.http.x-url
. - Ensure that www.example.com and example.com are cached as one, using
regsub()
. - Rewrite all URLs under http://sport.example.com to http://example.com/sport/. For example: http://sport.example.com/index.html to http://example.com/sport/index.html.
- Use HTTPie to verify the result.
- Extra: Make sure / and /index.html are cached as one object.
- Extra 2: Make the redirection work for any domain with sport. at the front. E.g: sport.example.com, sport.foobar.example.net, sport.blatti, etc.
For the first point, use set req.http.headername = "value";
or set req.http.headername = regsub(...);
.
In point 2, change req.http.host
by calling the function regsub(str, regex, sub)
.
str is the input string, in this case, req.http.host
.
regex is the regular-expression matching whatever content you need to change.
Use ^
to match what begins with www, and \.
to finish the regular-expression, i.e. ^www..
sub is what you desire to change it with, an empty string ""
can be used to remove what matches regex.
For point 3, you can check host headers with a specific domain name, for example: if (req.http.host == "sport.example.com")
.
An alternative is to check for all hosts that start with sport, regardless the domain name: if (req.http.host ~ "^sport\.")
.
In the first case, setting the host header is straight forward: set req.http.host = "example.com"
.
In the second case, you can set the host header by removing the string that precedes the domain name set req.http.host = regsub(req.http.host,"^sport\.", "");
Finally, you rewrite the URL in this way: set req.url = regsub(req.url, "^", "/sport");
.
To simulate client requests, you can either use HTTPie or varnishtest
.
If you need help, see Solution: Rewrite URL and Host Header Fields.
Tip
Remember that man vcl
contains a reference manual with the syntax and details of functions such as regsub(str, regex, sub)
.
We recommend you to leave the default VCL file untouched and create a new file for your VCL code.
Remember to update the location of the VCL file in the Varnish configuration file and reload it.
- Called upon entering pass mode
The vcl_pass
subroutine is called after a previous subroutine returns the pass action.
This actions sets the request in pass mode.
vcl_pass
typically serves as an important catch-all for features you have implemented in vcl_hit
and vcl_miss
.
vcl_pass
may return three different actions: fetch, synth, or restart.
When returning the fetch action, the ongoing request proceeds in pass mode.
Fetched objects from requests in pass mode are not cached, but passed to the client.
The synth and restart return actions call their corresponding subroutines.
- Used when an object should not be cached
- hit-for-pass object instead of fetched object
- Has TTL
Some requested objects should not be cached.
A typical example is when a requested page contains the Set-Cookie
response header, and therefore it must be delivered only to the client that requests it.
In this case, you can tell Varnish to create a hit-for-pass object and stores it in the cache, instead of storing the fetched object.
Subsequent requests are processed in pass mode.
When an object should not be cached, the beresp.uncacheable
variable is set to true.
As a result, the cacher process keeps a hash reference to the hit-for-pass object.
In this way, the lookup operation for requests translating to that hash find a hit-for-pass object.
Such requests are handed over to the vcl_pass
subroutine, and proceed in pass mode.
As any other cached object, hit-for-pass objects have a TTL. Once the object's TTL has elapsed, the object is removed from the cache.
vcl_backend_fetch
can be called from vcl_miss
or vcl_pass
.
When vcl_backend_fetch
is called from vcl_miss
, the fetched object may be cached.
If vcl_backend_fetch
is called from vcl_pass
, the fetched object is not cached even if obj.ttl
or obj.keep
variables are greater than zero.
A relevant variable is bereq.uncacheable
.
This variable indicates whether the object requested from the backend may be cached or not.
However, all objects from pass requests are never cached, regardless the bereq.uncacheable
variable.
vcl_backend_fetch
has two possible terminating actions, fetch or abandon.
The fetch action sends the request to the backend, whereas the abandon action calls the vcl_synth
subroutine.
The built-in vcl_backend_fetch
subroutine simply returns the fetch
action.
The backend response is processed by vcl_backend_response
or vcl_backend_error
depending on the response from the server.
If Varnish receives a syntactically correct HTTP response, Varnish pass control to vcl_backend_response
.
Syntactically correct HTTP responses include HTTP 5xx
error codes.
If Varnish does not receive a HTTP response, it passes control to vcl_backend_error
.
- Defines what is unique about a request.
vcl_hash
is always visited aftervcl_recv
or when another subroutine returns thehash
action keyword.
vcl_hash
defines the hash key to be used for a cached object.
Hash keys differentiate one cached object from another.
The default VCL for vcl_hash
adds the hostname or IP address, and the requested URL to the cache hash.
One usage of vcl_hash
is to add a user-name in the cache hash to identify user-specific data.
However, be warned that caching user-data should only be done cautiously.
A better alternative might be to hash cache objects per session instead.
The vcl_hash
subroutine returns the lookup
action keyword.
Unlike other action keywords, lookup
is an operation, not a subroutine.
The next state to visit after vcl_hash
depends on what lookup
finds in the cache.
When the lookup operation does not match any hash, it creates an object with a busy flag and inserts it in cache.
Then, the request is sent to the vcl_miss
subroutine.
The busy flag is removed once the request is handled, and the object is updated with the response from the backend.
Subsequent similar requests that hit busy flagged objects are sent into a waiting list. This waiting list is designed to improve response performance, and it is explain the Waiting State section.
Note
One cache hash may refer to one or many object variations. Object variations are created based on the Vary header field. It is a good practice to keep several variations under one cache hash, than creating one hash per variation.
- Executed after the lookup operation, called by
vcl_hash
, finds (hits) an object in the cache.
The vcl_hit
subroutine typically terminate by calling return()
with one of the following keywords:
deliver
, restart
, or synth
.
deliver
returns control to vcl_deliver
if the TTL + grace time
of an object has not elapsed.
If the elapsed time is more than the TTL
, but less than the TTL + grace time
, then deliver
calls for background fetch in parallel to vcl_deliver
.
The background fetch is an asynchronous call that inserts a fresher requested object in the cache.
Grace time is explained in the Grace Mode section.
restart
restarts the transaction, and increases the restart counter.
If the number of restarts is higher than max_restarts
counter, Varnish emits a guru meditation error.
synth(status code, reason)
returns the specified status code to the client and abandon the request.
- Subroutine called if a requested object is not found by the lookup operation.
- Contains policies to decide whether or not to attempt to retrieve the document from the backend, and which backend to use.
vcl_hit
and vcl_miss
are closely related.
It is rare that you customize them, because modification of HTTP request headers is typically done in vcl_recv
.
However, if you do not wish to send the X-Varnish
header to the backend server, you can remove it in vcl_miss
or vcl_pass
.
For that case, you can use unset bereq.http.x-varnish;
.- Common last exit point for all request workflows, except requests through
vcl_pipe
- Often used to add and remove debug-headers
The vcl_deliver
subroutine is simple, and it is also very useful to modify the output of Varnish.
If you need to remove a header, or add one that is not supposed to be stored in the cache, vcl_deliver
is the place to do it.
The variables most useful and common to modify in vcl_deliver
are:
resp.http.*
- Headers that are sent to the client. They can be set and unset.
resp.status
- The status code (200, 404, 503, etc).
resp.reason
- The HTTP status message that is returned to the client.
obj.hits
- The count of cache-hits on this object.
Therefore, a value of
0
indicates a miss. This variable can be evaluated to easily reveal whether a response comes from a cache hit or miss. req.restarts
- The number of restarts issued in VCL - 0 if none were made.
- Used to generate content within Varnish
- Error messages can be created here
- Other use cases: redirecting users (301/302 redirects)
vcl/default-vcl_synth.vcl:
You can create synthetic responses, e.g., personalized error messages, in vcl_synth
.
To call this subroutine you do:
return (synth(status_code, "reason"));
Note that synth
is not a keyword, but a function with arguments.
You must explicitly return the status code
and reason
arguments for vcl_synth
.
Setting headers on synthetic response bodies are done on resp.http
.
Note
From vcl/default-vcl_synth.vcl
, note that {"
and "}
can be used to make multi-line strings.
This is not limited to the synthetic()
function, but one can be used anywhere.
Note
A vcl_synth
defined object is never stored in cache, contrary to a vcl_backend_error
defined object, which may end up in cache.
vcl_synth
and vcl_backend_error
replace vcl_error
from Varnish 3.
Redirecting with VCL is fairly easy – and fast. Basic HTTP redirects work when the HTTP response is either 301 Moved Permanently or 302 Found. These response have a Location header field telling the web browser where to redirect.
Note
The 301 response can affect how browsers prioritize history and how search engines treat the content. 302 responses are temporary and do not affect search engines as 301 responses do.
- Add a header field holding the string
HIT
if the requested resource was found in cache, orMISS
otherwise - "Rename" the
Age
header field toX-Age
- Make the default error message more friendly.
- Cache invalidation is an important part of your cache policy
- Varnish automatically invalidates expired objects
- You can proactively invalidate objects with Varnish
- You should define your cache invalidation rules before caching objects specially in production environments
There are four mechanisms to invalidate caches in Varnish:
- HTTP PURGE
- Use the
vcl_purge
subroutine- Invalidate caches explicitly using objects' hashes
vcl_purge
is called viareturn(purge)
fromvcl_recv
vcl_purge
removes all variants of an object from cache, freeing up memory- The
restart
return action can be used to update immediately a purged object
- Banning
- Use the built-in function
ban(regex)
- Invalidates objects in cache that match the regular-expression
- Does not necessarily free up memory at once
- Also accessible from the management interface
- Force Cache Misses
- Use
req.hash_always_miss
invcl_recv
- If set to true, Varnish disregards any existing objects and always (re)fetches from the backend
- May create multiple objects as side effect
- Does not necessarily free up memory at once
- Surrogate keys
- For websites with the need for cache invalidation at a very large scale
- Varnish Software's implementation of surrogate keys
- Flexible cache invalidation based on cache tags
- Available as hashtwo VMOD in Varnish Plus 4.0
- Available as xkey VMOD in Varnish Cache 4.1 and later
Which and when to use?
Whenever you deal with caching, you have to eventually deal with the challenge of cache invalidation, or content update. Varnish has different mechanisms to addresses this challenge, but which one to use?
There is rarely a need to pick only one solution, as you can implement many of them. However, you can try to answer the following questions:
- Am I invalidating one or many specific objects?
- Do I need to free up memory or just replace the content?
- How long time does it take to replace the content?
- Is this a regular or a one-off task?
or follow these guidelines:
- If you need to invalidate more than one item at a time, consider using bans or hashtwo/xkey.
- If it takes a long time to pull content from the backend into Varnish, consider forcing cache misses by using
req.hash_always_miss
.
The rest of the chapter teaches you more about these cache invalidation mechanisms.
Note
Purge and hashtwo/xkey work very similar. The main difference is that they act on different hash keys.
- If you know exactly what to remove, use
HTTP PURGE
- Frees up memory, removes all
Vary:
-variants of the object - Leaves it to the next client to refresh the content
- Often combined with
return(restart);
- As easy as handling any other HTTP request
A purge is what happens when you pick out an object from the cache and discard it along with its variants.
A resource can exist in multiple Vary:
-variants.
For example, you could have a desktop version, a tablet version and a smartphone version of your site, and use the Vary
HTTP header field in combination with device detection to store different variants of the same resource.
Usually a purge is invoked through HTTP with the method PURGE
.
A HTTP PURGE
is another request method just as HTTP GET
.
Actually, you can call the PURGE
method whatever you like, but PURGE
has become the de-facto naming standard.
Squid, for example, uses the PURGE
method name for the same purpose.
Purges apply to a specific object, since they use the same lookup operation as in vcl_hash
.
Therefore, purges find and remove objects really fast!
There are, however, two clear down-sides. First, purges cannot use regular-expressions, and second, purges evict content from cache regardless the availability of the backend. That means that if you purge some objects and the backend is down, Varnish will end up having no copy of the content.
- You may add actions to be executed once the object and its variants is purged
- Called after the purge has been executed
Note
Cache invalidation with purges is done by calling return (purge);
from vcl_recv
in Varnish 4.
The keyword purge;
from Varnish 3 has been retired.
vcl/purge.vcl
In the example above, return (purge)
ends execution of vcl_recv
and jumps to vcl_hash
.
When vcl_hash
calls return(lookup)
, Varnish purges the object and then calls vcl_purge
.
You can test this code with HTTPie by issuing:
http -p hH --proxy=http:http://localhost PURGE www.example.com
Alternatively, you can test it with varnishtest
as in the subsection PURGE in varnishtest.
In order to control the IP addresses that are allowed to send PURGE
, you can use Access Control Lists (ACLs).
A purge example using ACLs is in the Access Control Lists (ACLs) section.
- Send a
PURGE
request to Varnish from your backend server after an article is published.- Simulate the article publication.
- The result is that the article is evicted in Varnish.
You are provided with article.php
, which fakes an article.
It is recommended to create a separate php file to implement purging.
article.php
If you need help, see Solution: PURGE an article from the backend.
Tip
Remember to place your php files under /var/www/html/
.
- Start the VCL processing again from the top of
vcl_recv
- Any changes made are kept
The restart
return action allows Varnish to re-run the VCL state machine with different variables.
This is useful in combination with PURGE, in the way that a purged object can be immediately restored with a new fetched object.
Every time a restart occurs, Varnish increments the req.restarts
counter.
If the number of restarts is higher than the max_restarts
parameter, Varnish emits a guru meditation error.
In this way, Varnish safe guards against infinite loops.
Warning
Restarts are likely to cause a hit against the backend, so do not increase max_restarts
thoughtlessly.
- Sets TTL to 0
- Allows Varnish to serve stale content to users if the backend is unavailable
- Asynchronous and automatic backend fetching to update object
Softpurge is cache invalidation mechanism that sets TTL to 0 but keeps the grace value of a cached object. This is useful if you want to build responses using the cached object while updating it.
Softpurge is a VMOD part of varnish-modules https://github.com/varnish/varnish-modules. For installation and usage details, please refer to its own documentation https://github.com/varnish/varnish-modules/blob/master/docs/vmod_softpurge.rst.
Tip
The xkey VMOD has the softpurge functionality too.
Use
ban
to invalidate caches on cache hitsFrees memory on ban patterns matching
Examples in the
varnishadm
command line interface:ban req.url ~ /foo
ban req.http.host ~ example.com && obj.http.content-type ~ text
ban.list
Example in VCL:
ban("req.url ~ /foo");
Example of VCL code to act on
HTTP BAN
request method:sub vcl_recv { if (req.method == "BAN") { ban("req.http.host == " + req.http.host + " && req.url == " + req.url); # Throw a synthetic page so the request won't go to the backend. return(synth(200, "Ban added")); } }
Banning in the context of Varnish refers to adding a ban expression that prohibits Varnish to serve certain objects from the cache. Ban expressions are more useful when using regular-expressions.
Bans work on objects already in the cache, i.e., it does not prevent new content from entering the cache or being served.
Cached objects that match a ban are marked as obsolete.
Obsolete objects are expunged by the expiry thread like any other object with obj.ttl == 0
.
Ban expressions match against req.*
or obj.*
variables.
Think about a ban expression as; "the requested URL starts with /sport
", or "the cached object has a header field with value matching lighttpd
".
You can add ban expressions in three ways: 1) VCL code, 2) use a customized HTTP request method, or 3) issuing commands in the varnishadm
CLI.
Ban expressions are inserted into a ban-list. The ban-list contains:
- ID of the ban,
- timestamp when the ban entered the ban-list,
- counter of objects that have matched the ban expression,
- a
C
flag for completed that indicates whether a ban is invalid because it is duplicated, - the ban expression.
To inspect the current ban-list, issue the ban.list
command in the CLI:
0xb75096d0 1318329475.377475 10 obj.http.x-url ~ test0 0xb7509610 1318329470.785875 20C obj.http.x-url ~ test1
Varnish tests bans whenever a request hits a cached object. A cached object is checked against bans added after the last checked ban. That means that each object checks against a ban expression only once.
Bans that match only against obj.*
are also checked by a background worker thread called the ban lurker.
The parameter ban_lurker_sleep
controls how often the ban lurker tests obj.*
bans.
The ban lurker can be disabled by setting ban_lurker_sleep
to 0.
Bans can free memory in a very scalable manner if used properly. Bans free memory only after a ban expression hits an object. However, since bans do not prevent new backend responses from being inserted in the cache, client requests that trigger the eviction of an object will most likely insert a new one matching the ban. Therefore, ban lurker banning is more effective when freeing memory, as we shall see next.
Note
You should avoid ban expressions that match against req.*
, because these expressions are tested only by client requests, not the ban lurker.
In other words, a req.*
ban expression will be removed from the ban list only after a request matches it.
Consequently, you have the risk of accumulating a very large number of ban expressions.
This might impact CPU usage and thereby performance.
Therefore, we recommend you to avoid req.*
variables in your ban expressions, and to use obj.*
variables instead.
Ban expressions using only obj.*
are called lurker-friendly bans.
Note
If the cache is completely empty, only the last added ban stays in the ban-list.
Tip
You can also execute ban expressions via the Varnish Administration Console (VAC).
- Ban expressions that match only against
obj.*
- Evaluated asynchronously by the ban lurker thread
- Similar to the concept of garbage collection
Ban expressions are checked in two cases: 1) when a request hits a cached object, or 2) when the ban lurker wakes up. The first case is efficient only if you know that the cached objects to be banned are frequently accessed. Otherwise, you might accumulate a lot of ban expressions in the ban-list that are never checked. The second case is a better alternative because the ban lurker can help you keep the ban-list at a manageable size. Therefore, we recommend you to create ban expressions that are checked by the ban lurker. Such ban expressions are called lurker-friendly bans.
Lurker-friendly ban expressions are those that use only obj.*
, but not req.*
variables.
Since lurker-friendly ban expressions lack of req.*
, you might need to copy some of the req.*
contents into the obj
structure.
In fact, this copy operation is a mechanism to preserve the context of client request in the cached object.
For example, you may want to copy useful parts of the client context such as the requested URL from req
to obj
.
The following snippet shows an example on how to preserve the context of a client request in the cached object:
sub vcl_backend_response { set beresp.http.x-url = bereq.url; } sub vcl_deliver { # The X-Url header is for internal use only unset resp.http.x-url; }
Now imagine that you just changed a blog post template that requires all blog posts that have been cached. For this you can issue a ban such as:
$ varnishadm ban 'obj.http.x-url ~ ^/blog'
Since it uses a lurker-friendly ban expression, the ban inserted in the ban-list will be gradually evaluated against all cached objects until all blog posts are invalidated.
The snippet below shows how to insert the same expression into the ban-list in the vcl_recv
subroutine:
sub vcl_recv { if (req.method == "BAN") { # Assumes the ``X-Ban`` header is a regex, # this might be a bit too simple. ban("obj.http.x-url ~ " + req.http.x-ban); return(synth(200, "Ban added")); } }
- Write a VCL program that handles the
PURGE
andBAN
HTTP methods. - When handling the
BAN
method, use the request header fieldsreq.http.x-ban-url
andreq.http.x-ban-host
- Use Lurker-Friendly Bans
- To build further on this, you can also use the
REFRESH
HTTP method that fetches new content, usingreq.hash_always_miss
, which is explained in the next subsection
To test this exercise, you can use HTTPie:
http -p hH PURGE http://localhost/testpage http -p hH BAN http://localhost/ 'X-Ban-Url: .*html$' \ 'X-Ban-Host: .*\.example\.com' http -p hH REFRESH http://localhost/testpage
For information on cache invalidation in varnishtest
, refer to the subsection Cache Invalidation in varnishtest.
If you need help, see Solution: Write a VCL program using purge and ban.
set req.hash_always_miss = true;
invcl_recv
- Causes Varnish to look the object up in cache, but ignore any copy it finds
- Useful way to do a controlled refresh of a specific object
- If the server is down, the cached object is left untouched
- Useful to refresh slowly generated content
Setting a request in pass mode instructs Varnish to always ask a backend for content, without storing the fetched object into cache.
The vcl_purge
removes old content, but what if the web server is down?
Setting req.has_always_miss
to true
tells Varnish to look up the content in cache, but always miss a hit.
This means that Varnish first calls vcl_miss
, then (presumably) fetches the content from the backend, cache the updated object, and deliver the updated content.
The distinctive behavior of req.hash_always_miss
occurs when the backend server is down or unresponsive.
In this case, the current cached object is untouched.
Therefore, client requests that do not enable req.hash_always_miss
keep getting the old and untouched cached content.
Two important use cases for using req.hash_always_miss
are when you want to:
1) control who takes the penalty for waiting around for the updated content (e.g. a script you control), and
2) ensure that content is not evicted before it is updated.
Note
Forcing cache misses do not evict old content. This means that causes Varnish to have multiple copies of the content in cache. In such cases, the newest copy is always used. Keep in mind that duplicated objects will stay as long as their time-to-live is positive.
- Hashtwo or xkey are the Varnish Software's implementation of surrogate keys
- Hashtwo is available in Varnish Cache Plus 3.x and 4.0 only
- Xkey is open source and is available in Varnish Cache 4.1 or later
- Cache invalidation based on cache tags
- Adds patterns easily to be matched against
- Highly scalable
The idea is that you can use any arbitrary string for cache invalidation. You can then key your cached objects on, for example, product ID or article ID. In this way, when you update the price of a certain product or a specific article, you have a key to evict all those objects from the cache.
So far, we have discussed purges and bans as methods for cache invalidation. Two important distinctions between them is that purges remove a single object (with its variants), whereas bans perform cache invalidation based on matching expressions. However, there are cases where none of these mechanisms are optimal.
Hashtwo/xkey creates a second hash key to link cached objects based on cache tags. This hash keys provide the means to invalidate cached objects with common cache tags.
In practice, hashtwo/xkey create cache invalidation patterns, which can be tested and invalidated immediately just as purges do. In addition, hashtwo/xkey is much more efficient than bans because of two reasons: 1) looking up hash keys is much more efficient than traversing ban-lists, and 2) every time you test a ban expression, it checks every object in the cache that is older than the ban itself.
The hashtwo and xkey VMOD are pre-built for supported versions and can be installed using regular package managers from the Varnish Software repositories. Once your repository is properly configured, as indicated in Solution: Install Varnish, issue the following commands to install the hashtwo VMOD:
On Debian or Ubuntu:
apt-get install libvmod-hashtwo
On Red Hat Enterprise Linux:
yum install libvmod-hashtwo
Finally, you can use this VMOD by importing it in your VCL code:
import hashtwo;
Xkey is a part of varnish-modules https://github.com/varnish/varnish-modules. For installation and usage details, please refer to its own documentation https://github.com/varnish/varnish-modules/blob/master/docs/vmod_xkey.rst.
Tip
The xkey VMOD has a softpurge function as well.
Use case: E-commerce site
Same logic for hashtwo and xkey
HTTP response header from web page containing three products:
8155054
,166412
and234323
:HTTP/1.1 200 OK Server: Apache/2.2.15 X-HashTwo: 8155054 X-HashTwo: 166412 X-HashTwo: 234323
HTTP request header to purge pages containing product
166412
:GET / HTTP/1.1 Host: www.example.com X-HashTwo-Purge: 166412
VCL example code for hashtwo:
import hashtwo; sub vcl_recv { if (req.http.X-HashTwo-Purge) { if (hashtwo.purge(req.http.X-HashTwo-Purge) != 0) { return (purge); } else { return (synth(404, "Key not found")); } } }
On an e-commerce site the backend application adds the X-HashTwo
HTTP header field for every product that is included in a web page.
The header for a certain page might look like the one above.
If you use xkey instead of hashtwo, you should rename that header so you do not get confused.
Normally the backend is responsible for setting these headers. If you were to do it in VCL, it will look something like this:
sub vcl_backend_response { set beresp.http.X-HashTwo = "secondary_hash_key"; }
In the VCL code above, the hashtwo key to be purged is the value in the X-HashTwo-Purge
HTTP header.
In order to keep the web pages in sync with the database, you can set up a trigger in your database.
In that way, when a product is updated, an HTTP request towards Varnish is triggered.
For example, the request above invalidates every cached object with the matching hashtwo header in hashtwo.purge(req.http.X-HashTwo-Purge)
or xkey.purge(req.http.X-Key-Purge)
for the xkey VMOD.
After purging, Varnish should respond something like:
HTTP/1.1 200 Purged Date: Thu, 24 Apr 2014 17:08:28 GMT X-Varnish: 1990228115 Via: 1.1 Varnish
The objects are now cleared.
Warning
You should protect purges with ACLs from unauthorized hosts.
This chapter is for the system administration course only
Varnish offers many mechanisms to save a request. By saving a request we mean:
- Rescue: mechanisms to handle requests when backends are in problematic situations.
- Economization: mechanisms to spend less resources, i.e., send less requests to the backend.
- Protection: mechanisms to restrict access cache invalidation from unauthorized entities.
Table 19 shows how different mechanisms are mapped to their saving meaning. This chapter explains how to make your Varnish setup more robust by using these mechanisms.
- Loadable VMOD
- Contains 1 or more backends
- All backends must be known
- Selection methods:
- round-robin
- fallback
- random
- seeded with a random number
- seeded with a hash key
Round-robin director example:
Varnish can have several backends defined, and it can set them together into clusters for load balancing purposes. Backend directors, usually just called directors, provide logical groupings of similar web servers by re-using previously defined backends. A director must have a name.
There are several different director selection methods available, they are: random, round-robin, fallback, and hash.
The next backend to be selected depends on the selection method.
You can specify the timeout before unused backend connections are closed by setting the backend_idle_timeout
parameter.
How to tune this and other parameters is further explained in the Tuning section.
A round-robin director takes only a backend list as argument. This director type picks the first backend for the first request, then the second backend for the second request, and so on. Once the last backend have been selected, backends are selected again from the top. If a health probe has marked a backend as sick, a round-robin director skips it.
A fallback director will always pick the first backend unless it is sick, in which case it would pick the next backend and so on. A director is also considered a backend so you can actually stack directors. You could for instance have directors for active and passive clusters, and put those directors behind a fallback director.
Random directors are seeded with either a random number or a hash key. Next section explains their commonalities and differences.
Note
Health probes are explain in the Health Checks section.
Note
Directors are defined as loadable VMODs in Varnish 4. See the vmod_directors man page for more information and examples.
Warning
If you declare backend servers, but do not use them,varnishd
returns error by default. You can avoid this situation by turning off the runtime parametervcc_err_unref
. However, this practice is strongly discouraged. Instead, we advise to declare only what you use.
- Random director: seeded with a random number
- Hash director: seeded with hash key typically from a URL or a client identity string
Hash director that uses client identity for backend selection
The random director picks a backend randomly.
It has one per-backend parameter called weight
, which provides a mechanism for balancing the selection of the backends.
The selection mechanism of the random director may be regarded as traffic distribution if the amount of traffic is the same per request and per backend.
The random director also has a director-wide counter called retries
, which increases every time the director selects a sick backend.
Both, the random and hash director select a backend randomly. The difference between these two is the seed they use. The random director is seeded with a random number, whereas the hash director is seeded with a hash key.
Hash directors typically use the requested URL or the client identity (e.g. session cookie) to compute the hash key. Since the hash key is always the same for a given input, the output of the hash director is always the same for a given hash key. Therefore, hash directors always select the same backend for a given input. This is also known as sticky session load balancing. You can learn more about sticky sessions in https://info.varnish-software.com/blog/proper-sticky-session-load-balancing-varnish.
Hash directors are useful to load balance in front of other Varnish caches or other web accelerators. In this way, cached objects are not duplicated across different cache servers.
Note
In Varnish 3 there is a client director type, which is removed in Varnish 4.
This client director type is a special case of the hash director.
Therefore, the semantics of a client director type are achieved using hash.backend(client.identity)
.
- Poke your web server every N seconds
- Affects backend selection
std.healthy(req.backend_hint)
- Set using
.probe
- Varnish allows at most
.threshold
amount of failed probes within a set of the last.window
probes varnishlog
: Backend_health
You can define a health check for each backend. A health check defines a probe to verify whether a backend replies on a given URL every given interval.
The above example causes Varnish to send a request to http://server1.example.com/healthtest every 4 seconds. This probe requires that at least 3 requests succeed within a sliding window of 5 request.
Varnish initializes backends marked as sick.
.initial
is another variable of .probe
.
This variable defines how many times the probe must succeed to mark the backend as healthy.
The .initial
default value is equal to .threshold – 1
.
When Varnish has no healthy backend available, it attempts to use a graced copy of the cached object that a request is looking for. The next section Grace Mode explains this concept in detail.
You can also declare standalone probes and reuse them for several backends. It is particularly useful when you use directors with identical behaviors, or when you use the same health check procedure across different web applications.
Note
Varnish does not send a Host header with health checks.
If you need that, you can define an entire request using .request
instead of .url
.
Note
The healthy
function is implemented as VMOD in Varnish 4.
req.backend.healthy
from Varnish 3 is replaced by std.healthy(req.backend_hint)
.
Do not forget to include the import line: import std;
Backend_health
tag invarnishlog -g raw -i Backend_health
# varnishlog -g raw -i Backend_health 0 Backend_health - default Still healthy 4--X-RH 5 3 5 0.012166 0.013693 HTTP/1.0 200 OK
varnishadm debug.health
in Varnish 4.0 orvarnishadm backend.list -p
in Varnish 4.1:Backend default is Healthy Current states good: 5 threshold: 3 window: 5 Average responsetime of good probes: 0.016226 Oldest Newest ================================================================ 44444444444444444444444444444444444444444444--44----444444444444 Good IPv4 XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX--XX----XXXXXXXXXXXX Good Xmit RRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR--RR----RRRRRRRRRRRR Good Recv HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH--HH----HHHHHHHHHHHH Happy
varnishadm backend.list
:Backend name Refs Admin Probe default(127.0.0.1,,8081) 1 probe Healthy 4/5
Every health test is recorded in the shared memory log with 0
VXID (see Transactions).
If you want to see Backend_health
records in varnishlog
, you have to change the default grouping by XVID to raw:
varnishlog -g raw -i Backend_health
Backend_health
records are led by 0
, which is the VXID number.
The rest of the probe record is in the following format:
Backend_health - %s %s %s %u %u %u %f %f %s | | | | | | | | | | | | | | | | | +- Probe HTTP response | | | | | | | +---- Average response time | | | | | | +------- Response time | | | | | +---------- Probe window size | | | | +------------- Probe threshold level | | | +---------------- Number of good probes in window | | +------------------- Probe window bits | +---------------------- Status message +------------------------- Backend name
Most of the fields are self-descriptive, but we clarify next the Probe window bits and Status message.
The Probe window bits field details the last probe with the following format:
%c %c %c %c %c %c %c | | | | | | | | | | | | | +- H -- Happy | | | | | +---- R -- Good Received (response from the backend received) | | | | +------- r -- Error Received (no response from the backend) | | | +---------- X -- Good Xmit (Request to test backend sent) | | +------------- x -- Error Xmit (Request to test backend not be sent) | +---------------- 6 -- Good IPv6 +------------------- 4 -- Good IPv4
Status message is a two word state indicator, which can be:
- Still healthy
- Back healthy
- Still sick
- Went sick
Note that Still indicates unchanged state, Back and Went indicate a change of state. The second word, healthy or sick, indicates the present state.
Another method to analyze health probes is by calling varnishadm debug.health
in Varnish 4.0 or varnishadm backend.list -p
in Varnish 4.1.
This command presents first data from the last Backend_health
log:
Backend default is Healthy Current states good: 5 threshold: 3 window: 5 Average responsetime of good probes: 0.016226
and the last 64 window bits of probes:
Oldest Newest ================================================================ 44444444444444444444444444444444444444444444--44----444444444444 Good IPv4 XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX--XX----XXXXXXXXXXXX Good Xmit RRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR--RR----RRRRRRRRRRRR Good Recv HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH--HH----HHHHHHHHHHHH Happy
See the power of health probes!
Suggested steps for the demo:
- Configure a probe as shown in Health Checks.
- For Varnish 4.0, run
watch -n.5 varnishadm debug.health
in one terminal - For Varnish 4.1, run
watch -n.5 varnishadm backend.list -p
in one terminal - Start and stop your backend
For this, you might want to simulate very quickly a backend with the command
python -m SimpleHTTPServer [port]
. - The watch command makes the effect of an animated health prober!
- A graced object is an object that has expired, but is kept in cache for a given grace time
- Grace mode is when Varnish uses a graced object
- Grace mode is a feature to mitigate the accumulation of requests for expired objects
- Grace mode allows Varnish to build responses from expired objects
beresp.grace
defines the time that Varnish keeps an object afterberesp.ttl
has elapsed
The main goal of grace mode is to avoid requests to pile up whenever a popular object has expired in cache.
To understand better grace mode, recall Figure 2 which shows the lifetime of cached objects.
When possible, Varnish delivers a fresh object, otherwise Varnish builds a response from a stale object and triggers an asynchronous refresh request.
This procedure is also known as stale-while-revalidate
.
The typical way to use grace is to store an object for several hours after its TTL
has elapsed.
In this way, Varnish has always a copy to be delivered immediately, while fetching a new object asynchronously.
This asynchronous fetch ensures that graced objects do not get older than a few seconds, unless there are no available backends.
The following VCL code illustrates a typical use of grace:
Graced objects are those with a grace time that has not yet expired.
The grace time is stored in obj.grace
, which default is 10 seconds.
You can change this value by three means:
- by parsing the HTTP
Cache-Control
fieldstale-while-revalidate
that comes from the backend, - by setting the variable
beresp.grace
in VCL, or - by changing the grace default value with
varnishadm param.set default_grace <value>
.
Varnish 4.1 parses stale-while-revalidate
automatically from the Cache-Control
header field.
For example, when receiving "Cache-Control: max-age=5, stale-while-revalidate=30"
, Varnish 4.1 sets obj.ttl=5
and obj.grace=30
automatically.
To see a working example on how Varnish works with Cache-Control
, see the VTC in Understanding Grace using varnishtest.
Note
obj.ttl
and obj.grace
are countdown timers.
Objects are valid in cache as long as they have a positive remaining time equal to obj.ttl
+ obj.grace
.
Backend response HTTP Cache-Control header field:
"Cache-control: max-age=60, stale-while-revalidate=30"
or set in VCL:
set beresp.ttl = 60s; set beresp.grace = 30s;
- 50s: Normal delivery
- 62s: Normal cache miss, but grace mode possible
- 80s: Normal cache miss, but grace mode possible
- 92s: Normal cache miss, object is removed from cache
TTL
are delivered, set beresp.grace = 0
.
The downside of this is that all grace functionality is disabled, regardless any reason.Copy the following CGI script in
/usr/lib/cgi-bin/test.cgi
:#!/bin/sh sleep 10 echo "Content-type: text/plain" echo "Cache-control: max-age=10, stale-while-revalidate=20" echo echo "Hello world" date
Make the script executable.
Issue
varnishlog -i VCL_call,VCL_return
in one terminal.Test that the script works outside Varnish by typing
http http://localhost:8080/cgi-bin/test.cgi
in another terminal.Send a single request, this time via Varnish, to cache the response from the CGI script. This should take 10 seconds.
Send three requests: one before the TTL (10 seconds) elapses, another after 10 seconds and before 30 seconds, and a last one after 30 seconds.
Repeat until you understand the output of
varnishlog
.Play with the values of
max-age
andstale-while-revalidate
in the CGI script, and theberesp.grace
value in the VCL code.
- Available in
vcl_backend_response
andvcl_backend_error
- Re-enters
vcl_backend_fetch
- Any changes made are kept
- Parameter
max_retries
safe guards against infinite loops - Counter
bereq.retries
registers how many retries are done
The retry
return action is available in vcl_backend_response
and vcl_backend_error
.
This action re-enters the vcl_backend_fetch
subroutine.
This only influences the backend thread, the client-side handling is not affected.
You may want to use this action when the backend fails to respond. In this way, Varnish can retry the request to a different backend. For this, you must define multiple backends.
You can use directors to let Varnish select the next backend to try.
Alternatively, you may use bereq.backend
to specifically select another backend.
return (retry)
increments the bereq.retries
counter.
If the number of retries is higher than max_retries
, control is passed to vcl_backend_error
.
Note
In Varnish 3.0 it is possible to do return (restart)
after the backend response failed.
This is now called return (retry)
, and jumps back up to vcl_backend_fetch
.
- Saint mode is implemented as a backend director with the following capabilities:
- Fine-grained health checks; maintains a blacklist of relations between objects and backends
- Objects have a blacklist TTL
- Backends in the blacklist have a threshold of related objects
- Backends with objects below the threshold can be selected to serve other objects
- Backends with objects above the threshold are marked as sick for all objects
- Available in Varnish Cache 4.1 or later
Saint mode complements regular Health Checks by marking backend sicks for specific object. Saint mode is a VMOD that maintains a blacklist of objects and related backends. Each blacklisted object has a TTL, which denotes the time it stays in the blacklist.
If the number of blacklisted objects for a backend are below a threshold, the backend is considered partially sick. Requests for blacklisted objects might be sent to another backend. When the number of blacklisted objects for a backend exceeds a threshold, the backend is marked as sick for all requests.
vcl/saintmode.vcl below is typical usage of saint mode.
In this example, a request with a 500
response status would be retried to another backend.
An alternative is to build the response with a stale object.
For that, you would return(abandon)
, restart
the request in vcl_synth
, check for req.restarts
in vcl_recv
.
To get a better idea on how to do it, please take a look the stale-if-error
snippet in https://github.com/fgsch/vcl-snippets/blob/master/v4/stale-if-error.vcl.
The fine-grained checks of saint mode help to spot problems in malfunctioning backends.
For example, if the request for the object foo returns 200 OK
HTTP response without content (Content-Length = 0
), you can blacklist that specific object for that specific backend.
You can also print the object with std.log
and filter it in varnishlog
.
Note
For more information, please refer to its own documentation in https://github.com/varnish/varnish-modules/blob/master/docs/vmod_saintmode.rst.
If a backend has not enough resources, it might be advantageous to set max_connections
.
So that a limited number of simultaneous connections are handled by a specific backend.
All backend-specific timers are available as parameters and can be overridden in VCL on a backend-specific level.
Tip
Varnish only accepts hostnames for backend servers that resolve to a maximum of one IPv4 address and one IPv6 address.
The parameter prefer_ipv6
defines which IP address Varnish prefer.
- An ACL is a list of IP addresses
- VCL programs can use ACLs to define and control the IP addresses that are allowed to purge, ban, or do any other regulated task.
- Compare with
client.ip
orserver.ip
An Access Control List (ACL) declaration creates and initializes a named list of IP addresses and ranges, which can later be used to match client or server IP addresses.
ACLs can be used for anything.
They are typically used to control the IP addresses that are allowed to send PURGE
or ban requests, or even to avoid the cache entirely.
You may also setup ACLs to differentiate how your Varnish servers behave.
You can, for example, have a single VCL program for different Varnish servers.
In this case, the VCL program evaluates server.ip
and acts accordingly.
ACLs are fairly simple to create.
A single IP address or hostname should be in quotation marks, as "localhost"
.
ACL uses the CIDR notation to specify IP addresses and their associated routing prefixes.
In Varnish's ACLs the slash "/
" character is appended outside the quoted IP address, for example "192.168.1.0"/24
.
To exclude an IP address or range from an ACL, and exclamation mark "!
" should precede the IP quoted address.
For example !"192.168.1.23"
.
This is useful when, for example, you want to include all the IP address in a range except the gateway.
Warning
If you declare ACLs, but do not use them, varnishd
returns error by default.
You can avoid this situation by turning off the runtime parameter vcc_err_unref
.
However, this practice is strongly discouraged.
Instead, we advise to declare only what you use.
- Where to compress? backend or Varnish?
- Parameter to toggle:
http_gzip_support
- VCL variable
beresp.do_gzip
to zip andberesp.do_gunzip
to unzip
sub vcl_backend_response { if (beresp.http.content-type ~ "text") { set beresp.do_gzip = true; } }
- Avoid compressing already compressed files
- Works with ESI
It is sensible to compress objects before storing them in cache. Objects can be compressed either at the backend or your Varnish server, so you have to make the decision on where to do it. Factors that you should take into consideration are:
- where to store the logic of what should be compressed and what not
- available CPU resources
Also, keep in mind that files such as JPEG, PNG, GIF or MP3 are already compressed. So you should avoid compressing them again in Varnish.
By default, http_gzip_support
is on, which means that Varnish follows the behavior described in https://www.varnish-cache.org/docs/trunk/phk/gzip.html and https://www.varnish-cache.org/docs/trunk/users-guide/compression.html.
If you want to have full control on what is compressed and when, set the http_gzip_support
parameter to off, and activate compression based on specific rules in your VCL code.
Implement these rules in vcl_backend_response
and then set beresp.do_gzip
or beresp.do_gunzip
as the example above.
If you compose your content using Edge Side Includes (ESI), you should know that ESI and gzip work together. Next chapter explains how to compose your content using Varnish and Edge Side Includes (ESI).
Note
Compression in Varnish uses and manipulates the Accept-Encoding
and Content-Encoding
HTTP header fields.
Etag
validation might also be weakened.
Refer to https://www.varnish-cache.org/docs/trunk/phk/gzip.html and https://www.varnish-cache.org/docs/trunk/users-guide/compression.html for all details about compression.
This chapter is for the web-developer course only
This chapter teaches you how to glue content from independent sources into one web page.
- Cookies and how to work with them
- Edge Side Includes (ESI) and how to compose a single client-visible page out of multiple objects
- Combining ESI and Cookies
- AJAX and masquerading AJAX requests through Varnish
Most websites follow a pattern: they have easily distinguishable parts:
- A front page
- Articles or sub-pages
- A login-box or "home bar"
- Static elements, like CSS, JavaScript and graphics
To truly utilize Varnish to its full potential, start by analyzing the structure of the website. Ask yourself this:
- What makes web pages in your server different from each other?
- Does the differences apply to entire pages, or only parts of them?
- How can I let Varnish to know those differences?
Beginning with the static elements should be easy. Previous chapters of this book cover how to handle static elements. How to proceed with dynamic content?
An easy solution is to only cache content for users that are not logged in. For news-papers, that is probably enough, but not for web-shops.
Web-shops re-use objects frequently. If you can isolate the user-specific bits, like the shopping cart, you can cache the rest. You can even cache the shopping cart, if you tell Varnish when to change it.
The most important lessons is to start with what you know.
- Be careful when caching cookies!
- Cookies are frequently used to identify unique users, or user's choices.
- They can be used for anything from identifying a user-session in a web-shop to opting for a mobile version of a web page.
- Varnish can handle cookies coming from two different sources:
req.http.Cookie
header field from clientsberesp.http.Set-Cookie
header field from servers
By default Varnish does not cache a page if req.http.Cookie
or beresp.http.Set-Cookie
are present.
This is for two main reasons:
1) to avoid littering the cache with large amount of copies of the same content, and
2) to avoid delivering cookie-based content to a wrong client.
It is far better to either cache multiple copies of the same content for each user or cache nothing at all, than caching personal, confidential or private content and deliver it to a wrong client. In other words, the worst is to jeopardize users' privacy for saving backend resources. Therefore, it is strongly advised to take your time to write a correct VCL program and test it thoroughly before caching cookies in production deployments.
Despite cookie-based caching being discouraged, Varnish can be forced to cache content based on cookies.
If a client request contains req.http.Cookie
, use return (hash);
in vcl_recv
.
If the cookie is a Set-Cookie
HTTP response header field from the server, use return (deliver);
in vcl_backend_response
.
Note
If you need to handle cookies, consider using the cookie
VMOD from https://github.com/varnish/varnish-modules/blob/master/docs/vmod_cookie.rst.
This VMOD handles cookies with convenient parsing and formatting functions without the need of regular-expressions.
- Used to cache content that varies on cookies
- By default, Varnish does not store responses when cookies are involved
- The
Vary
response header field can be used to store responses that are based on the value of cookies - Cookies are widely used, but not
Vary: Cookie
Varnish uses a different hash value for each cached resource.
Resources with several representations, i.e. variations containing the Vary
response header field, share the same hash value in Varnish.
Despite this common hash value, caching based on the Vary: Cookie
response header is not advised, because of its poor performance.
For a more detailed explanation on Vary
, please refer to the Vary subsection.
Note
Consider using Edge Side Includes to let Varnish build responses that combine content with and without cookies, i.e. combining caches and responses from the origin server.
Remove all cookies that you do not need
Organize the content of your web site in a way that let you easily determine if a page needs a cookie or not. For example:
/common/
-- no cookies/user/
-- has user-cookies/voucher/
-- has only the voucher-cookie- etc.
Add the
req.http.Cookie
request header to the cache hash by issuinghash_data(req.http.cookie);
invcl_hash
.Never cache a
Set-Cookie
header. Either remove the header before caching or do not cache the object at all.To ensure that all cached pages are stripped of
Set-Cookie
, finishvcl_backend_response
with something similar to:if (beresp.ttl > 0s) { unset beresp.http.Set-cookie; }
In this exercise you have to use two cache techniques; first Vary
and then hash_data()
.
The exercise uses the Cookie
header field, but the same rules apply to any other field.
For that, prepare the testbed and test with HTTPie:
Copy the file
material/webdev/cookies.php
to/var/www/html/cookies.php
.Send different requests in HTTPie changing
/cookies.php
anduser=Alice
for/article.html
anduser=Bob
, e.g.:http http://localhost/cookies.php "Cookie: user=Alice"
Vary: Part 1:
- Write a VCL program to force Varnish to cache client requests with cookies.
- Send two client requests for the same URL; one for user Alice and one for user Bob.
- Does Varnish use different backend responses to build and deliver the response to the client?
- Make
cookies.php
send theVary: Cookie
response header field, then analyze the response to the client. - Remove
beresp.http.Vary
in vcl_backend_response and see if Varnish still honors theVary
header.
Vary: Part 2:
- Purge the cached object for resource
/cookies.php
. - Check if it affects all, none or just one of the objects in cache (e.g: change the value of the cookie and see if the
PURGE
method has purged all of them).
hash_data(): Part 1:
- Write another VCL program or add conditions to differentiate requests handled by
Vary
andhash_data()
. - Add
hash_data(req.http.Cookie);
in vcl_hash. - Check how multiple values of
Cookie
give individual cached objects.
hash_data(): Part 2:
- Purge the cache again and check the result after using
hash_data()
instead ofVary: Cookie
.
Vary
and hash mechanisms.
These mechanisms can also be tested and learned through varnishtest
.
If you have time and are curious enough, please do the Exercise: Handle Cookies with Vary and hash_data() in varnishtest.
After solving these exercises, you will understand very well how Vary
and hash_data();
work.- What is ESI?
- How to use ESI?
- Testing ESI without Varnish
- ESI has a linear growth complexity
- Serial ESI available in Varnish Cache
- Parallel ESI in Varnish Plus only
Edge Side Includes or ESI is a small markup language for dynamic web page assembly at the reverse proxy level. The reverse proxy analyses the HTML code, parses ESI specific markup and assembles the final result before flushing it to the client. Figure 27 depicts this process.
With ESI, Varnish can be used not only to deliver objects, but to glue them together. The most typical use case for ESI is a news article with a most recent news box at the side. The article itself is most likely written once and possibly never changed, and can be cached for a long time. The box at the side with most recent news, however, changes frequently. With ESI, the article can include a most recent news box with a different TTL.
When using ESI, Varnish fetches the news article from a web server, then parses the <esi:include src="/url" />
ESI tag, and fetches the URL via a normal request.
Either finding it already cached or getting it from a web server and inserting it into cache.
The TTL of the ESI element can be 5 minutes while the article is cached for two days. Varnish delivers the two different objects in one glued page. Thus, Varnish updates parts independently and makes possible to combine content with different TTL.
Enabling ESI in Varnish is simple enough:
To include a page in another, the <esi:include>
ESI tag is used:
<esi:include src="/url" />
You can also strip off cookies per ESI element. This is done in vcl_recv.
Varnish only supports three ESI tags:
<esi:include>
: calls the page defined in thesrc
attribute and replaces the ESI tag with the content ofsrc
.<esi:remove>
: removes any code inside this opening and closing tag.<!--esi ``(content)
-->``: Leaves(content)
unparsed. E.g., the following does not process the<esi:include>
tag:<!--esi This ESI tag is not processed: <esi:include src="example"> -->
varnishtest
is a useful tool to understand how ESI works.
The subsection Understanding ESI in varnishtest contains a Varnish Test Case (VTC) using ESI.
Note
Varnish outputs ESI parsing errors in varnishstat
and varnishlog
.
Copy material/webdev/esi-date.php
to /var/www/html/
.
This file contains an ESI include tag:
Copy material/webdev/esi-date.cgi
to /usr/lib/cgi-bin/
.
This file is a simple CGI that outputs the date of the server:
For ESI to work, load the following VCL code:
Then reload your VCL (see Table 6 for reload instructions) and issue the command http http://localhost/esi-date.php
.
The output should show you how Varnish replaces the ESI tag with the response from esi-date.cgi
.
Note the different TTLs from the glued objects.
- Use
material/webdev/esi-top.php
andmaterial/webdev/esi-user.php
to test ESI. - Visit
esi-top.php
and identify the ESI tag. - Enable ESI for
esi-top.php
in VCL and test. - Strip all cookies from
esi-top.php
and make it cache. - Let
esi-user.php
cache too. It emitsVary: Cookie
, but might need some help.
See the suggested solutions of Exercise: Handle Cookies with Vary and hash_data() in varnishtest to get an idea on how to solve this exercise.
Try to avoid return (hash);
in vcl_recv
and return (deliver);
in vcl_backend_response
as much as you can.
This is a general rule to make safer Varnish setups.
During the exercise, make sure you understand all the cache mechanisms at play.
You can also try removing the Vary: Cookie
header from esi-user.php
.
You may also want to try PURGE
.
If so, you have to purge each of the objects, because purging just /esi-top.php
does not purge /esi-user.php
.
- Test ESI Using JavaScript to fill in the blanks.
During development of different web pages to be ESI-glued by Varnish, you might not need Varnish all the time. One important reason for this, is to avoid caching during the development phase. There is a solution based on JavaScript to interpret ESI syntax without having to use Varnish at all. You can download the library at the following URL:
Once downloaded, extract it in your code base, include esiparser.js
and include the following JavaScript code to trigger the ESI parser:
$(document).ready( function () { do_esi_parsing(document); });
![]() |
![]() |
This works | This does not work |
material/webdev/ajax.html
Use the provided ajax.html
page.
Note that function getNonMasqueraded()
fails because the origin is distinct to the google.com
domain.
Function getMasqueraded()
can do the job if a proper VCL code handles it.
Write the VCL code that masquerades the Ajax request to http://www.google.com/robots.txt
.
If you need help, see Solution: Write a VCL that masquerades XHR calls.
The Varnish Plus offer of software products includes:
- Varnish Massive Storage Engine (MSE) described in Storage Backends,
- Hashtwo (Varnish Software Implementation of Surrogate Keys) described in Hashtwo/Xkey (Varnish Software Implementation of Surrogate Keys),
- Varnish Administration Console (VAC),
- Varnish Custom Statistics (VCS),
- Varnish High Availability (VHA),
- SSL/TLS frontend support with hitch,
- and more.
For more information about the complete Varnish Plus offer and their documentation, please visit:
- Single point of control for simultaneous administration of multiple Varnish Cache servers
- VAC provides:
- GUI
- API
- Super Fast Purger
- VAC has its own documentation
The Varnish Administration Console (VAC) consists of a GUI and an API. VAC is most commonly used in production environments where real-time graphs and statistics help identify bottlenecks and issues within Varnish Cache servers. VAC is a management console for groups of Varnish Cache servers, also known as cache groups. A cache group is a collection of Varnish Cache servers that have identical configuration. Attributes on a cache group includes:
- One or more Varnish Cache servers
- Active Varnish Configuration Language (VCL) file
- Homogeneous parameter configuration across all servers in a group
VAC distributes and store VCL files for you. A parameter set is a list of Varnish cache parameters. These parameters can be applied to one or more cache groups simultaneously, as long as all cache groups consist of cache servers of the same version.
VAC ships with a JSON-based RESTful API to integrate your own systems with the VAC. All actions performed via the user interface can be replicated with direct access to the API. This includes fetching all real-time graph data.
The Super Fast Purger is a high performance cache invalidation delivery mechanism for multiple installations of Varnish. Super Fast Purger is capable of distributing purge requests to cache groups across data centers via the Restful interface. Super Fast Purger uses HMAC as security mechanism to protect your purge requests and thus ensure data integrity.
In order to install VAC on either Debian/Ubuntu or Red Hat Enterprise, one would require access to the Varnish Plus Software repository. As a Varnish Plus customer, you have access to the installation guide document. This document has instructions to install, configure, maintain, and troubleshoot your VAC installation If you have any questions on how to set up your repository or where to obtain the VAC installation guide, please ask the instructor or send us an email to support@varnish-software.com.
Figures 26, Figures 27 and Figures 28 show screenshots of the GUI. You may also be interested in trying the VAC demo at https://vacdemo.varnish-software.com. The instructor of the course provides you the credentials.
- Data stream management system (DSMS) for your Varnish servers
- Real-time statistics engine to aggregate, display and analyze user web traffic
- Provides an API to retrieve statistics
- Provides a GUI that presents lists and charts to get a quick overview of the key metrics that matters you
Varnish Custom Statistics (VCS) is our data stream management system (DSMS) implementation for Varnish.
VCS allows you to analyze the traffic from multiple Varnish servers in near real-time to compute traffic statistics and detect critical conditions.
This is possible by continuously extracting transactions with the vcs-key
tags in your VSL.
Thus, VCS does not slow down your Varnish servers.
You can add as many custom vcs-key
tags as you need in your VCL code.
This allows you to define your own metrics.
VCS can be used to produce statistical data or even apply complex event processing techniques. Thus, VCS offers endless opportunities for tracking all aspects of websites' behavior. Typical cases include:
- A/B testing
- Measuring click-through rate
- Track slow pages and cache misses
- Analyze what is "hot" right now in a news website
- Track changes in currency conversions in e-commerce
- Track changes in Stock Keeping Units (SKUs) <behavior in e-commerce
- Track number of unique consumers of HLS/HDS/DASH video streams
VCS is a great tool when you want to test some functionality in your backend. For that, you can separate your requests into different groups, handle their requests accordingly, analyze the results and conclude whether your new functionality should be applied to all groups. This type of tests are called A/B testing. If you want to learn how to implement A/B testing in Varnish, please refer to https://info.varnish-software.com/blog/live-ab-testing-varnish-and-vcs.
Figure 32 and Figure 33 are screenshots of the VCS GUI. These screenshots are from the demo on http://vcsdemo.varnish-software.com. Your instructor can provide you credential for you to try the demo online.
Note
For further details on VCS, please look at its own documentation at https://www.varnish-software.com/resources/.
- Represents a finite relation from an infinite stream.
- Uses time-based tumbling windows
- API to query data model
- API outputs in JSON and JSONP format
VCS uses the time-based tumbling windows technique to segment the data stream into finite parts.
These windows are created based on the vcs-key
tag that you specify in your VCL code.
Each window aggregates the data within a configurable period of time.
Table 20 shows the data model in VCS.
This table is basically a representation of two windows seen as two records in a conventional database.
In this example, data shows two windows of 30 seconds based on the example.com
vcs-key
.
For presentation purposes in this page, the distribution of this table is of a database that grows from left to right.
The VCS data model has the following fields:
vcs-key
- common key name for transactions making this record
timestamp
- Timestamp at the start of the window
n_req
- Number of requests
n_req_uniq
- Number of unique requests, if configured
n_miss
- Number of backend requests (i.e. cache misses)
Number of hits can be calculated as
n_hit = n_req - n_miss
avg_restart
- Average number of VCL restarts triggered per request
n_bodybytes
- Total number of bytes transferred for the response bodies
ttfb_miss
- Average time to first byte for requests that ended up with a backend request
ttb_hit
- Average time to first byte for requests that were served directly from varnish cache
resp_1xx
--resp_5xx
- Counters for response status codes.
reqbytes
- Number of bytes received from clients.
respbytes
- Number of bytes transmitted to clients.
berespbytes
- Number of bytes received from backends.
bereqbytes
- Number of bytes transmitted to backends.
You can think of each window as a record of a traditional database that resides in memory. This database is dynamic, since the engine of VCS updates it every time a new window (record) is available. VCS provides an API to retrieve this data from the table above in JSON format:
{ "example.com": [ { "timestamp": "2013-09-18T09:58:30", "n_req": 76, "n_req_uniq": "NaN", "n_miss": 1, "avg_restarts": 0.000000, "n_bodybytes": 10950, "ttfb_miss": 0.000440, "ttfb_hit": 0.000054, "resp_1xx": 0, "resp_2xx": 76, "resp_3xx": 0, "resp_4xx": 0, "resp_5xx": 0, ... }, { "timestamp": "2013-09-18T09:58:00", "n_req": 84, "n_req_uniq": "NaN", "n_miss": 0, "avg_restarts": 0.000000, "n_bodybytes": 12264, "ttfb_miss": "NaN", "ttfb_hit": 0.000048, "resp_1xx": 0, "resp_2xx": 84, "resp_3xx": 0, "resp_4xx": 0, "resp_5xx": 0, ... }, ... ] }
- API provides ready-to-use queries
- Queries over HTTP
- Top-most sorting
- Results in JSON and JSONP format
Examples:
For vcs-key
with names ending with .gif
, retrieve a list of the top 10:
/match/(.*)%5C.gif$/top
Find a list of the top 50 slowest backend requests:
/all/top_ttfb/50
The VCS API queries the VCS data model and the output is in JSON format. The API responds to requests for the following URLs:
/key/<vcs-key>
- Retrieves stats for a single
vcs-key
.<vcs-key>
name must be URL encoded. /match/<regex>
- Retrieves a list of
vcs-key
matching the URL encoded regular-expression. Accepts the query parameterverbose=1
, which displays all stats collected for the<vcs-keys>
matched. /all
- Retrieves a list of all the
<vcs-keys>
currently in the data model.
For /match/<regex>
and /all
, VCS can produce sorted lists.
For that, you can append one of the following sorting commands.
/top
- Sort based on number of requests.
/top_ttfb
- Sort based on the
ttfb_miss
field. /top_size
- Sort based on the
n_bodybytes
field. /top_miss
- Sort based on the
n_miss
field. /top_respbytes
- Sort based on number of bytes transmitted to clients.
/top_reqbytes
- Sort based on number of bytes received from clients.
/top_berespbytes
- Sort based on number of bytes fetched from backends.
/top_bereqbytes
- Sort based on number of bytes transmitted to backends.
/top_restarts
- Sort based on the
avg_restarts
field. /top_5xx
,/top_4xx
, ...,/top_1xx
- Sort based on number of HTTP response codes returned to clients for 5xx, 4xx, 3xx, etc.
/top_uniq
- Sort based on the
n_req_uniq
field.
Further, a /k
parameter can be appended, which specifies the number of keys to include in the top list.
If no k
value is provided, the top 10 is displayed.
Note
For installation instructions, please refer to http://files.varnish-software.com/pdfs/installation-guide_vcs-latest.pdf.
Once you have installed all necessary components, take a look at the man pages of vstatd
and vstatdprobe
for more documentation.
- VCS provides its own GUI
- You can interact with the API via this GUI
- Screenshots from http://vcsdemo.varnish-software.com/
- Content replicator
- Increases resiliency and performance
- Two-server, circular, multi-master replication
- Requests to replicate content against Varnish servers, not the backend
The Varnish High Availability agent (vha-agent) is a content replicator with the aim of copying the cached objects from an origin Varnish server to a neighboring Varnish server. This increases resiliency and performance, specially when backend traffic surges.
vha-agent reads the log of Varnish, and for each object insertion detected it fires a request to the neighboring Varnish server. This server fetches the object from the origin Varnish server. As a result, the same object is cached in both servers with only one single backend fetch.
This solution requires vha-agent to be installed on the origin Varnish server, and some simple VCL configuration on the replicated Varnish server. Ideally, vha-agent is installed on both servers so they can both replicate object insertions from each other in an active/active configuration.
Typical uses of VHA include:
- Business critical Varnish installations
- Any multi-cache Varnish setup
- Multi node CDN POP installations
The replication of cached objects may bring the need for multiple cache invalidation. For that purpose, you can use the Varnish Administration Console (VAC). Remember: you should define the rules on how to invalidate cached objects before caching them in production environments.
- Varnish supports SSL/TLS encryption
- Backend encryption in Varnish Cache Plus
- Client encryption in Varnish Cache Plus 4.1 with hitch
- Hitch: network proxy that terminates SSL/TLS connections and forwards the unencrypted traffic
- Configuration file:
/etc/hitch/hitch.conf
- Configure Varnish to listen to
PROXY
requests in/etc/varnish/varnish.params
Backend encryption is useful for deployments with geographically distributed origin servers such as CDNs. Varnish supports SSL/TLS encryption to secure communication on both: backend and frontend without third-party solutions. SSL/TLS configuration for connections between Varnish and the backend is described in Exercise: Configure Varnish.
Varnish Plus integrates hitch, which can have tens of thousands of listening sockets and hundreds of thousands of certificates. Following are the steps to configure Varnish to accept SSL/TLS connections with hitch.
Configure your package repository as explained in Solution: Install Varnish.
Install hitch in RedHat systems:
$ yum install varnish-plus-addon-ssl
or Ubuntu based systems:
$ apt-get install varnish-plus-addon-ssl
Create a key
.pem
file:$ /etc/pki/tls/certs/make-dummy-cert your-cdn.pem
For the purposes of this book, we create a dummy key and certification file concatenated in the
.pem
file. See https://docs.varnish-software.com/tutorials/hitch-letsencrypt/ or https://github.com/varnish/hitch/blob/master/docs/certificates.md for alternative methods.Configure hitch in
/etc/hitch/hitch.conf
:frontend = "[*]:443" backend = "[127.0.0.1]:6081" pem-file = "/path/to/your-cdn.pem" ciphers = "EECDH+AESGCM:EDH+AESGCM:AES256+EECDH:AES256+EDH" prefer-server-ciphers = off ssl-engine = "" workers = 1 backlog = 100 keepalive = 3600 chroot = "" user = "hitch" group = "hitch" quiet = off syslog = on syslog-facility = "daemon" daemon = on write-ip = off write-proxy-v1 = on write-proxy-v2 = off proxy-proxy = off sni-nomatch-abort = off
If your server is behind a firewall, ensure it can accept HTTPS connections.
In
/etc/varnish/varnish.params
, configure Varnish Plus to listen toPROXY
requests on port6081
:DAEMON_OPTS="-a :6081,PROXY"
Start hitch:
$ service hitch start
At the moment of writing this text,
service hitch start
did not output starting errors. You should check whether hitch has started, if not, try the following command to debug:$ /usr/sbin/hitch --pidfile=/run/hitch/hitch.pid \ --config=/etc/hitch/hitch.conf
Note
Hitch has its own documentation in its man pages man hitch
and man hitch.conf
.
Additional information at https://github.com/varnish/hitch.
Community driven:
- https://www.varnish-cache.org
- https://www.varnish-cache.org/docs
- http://repo.varnish-cache.org
- https://www.varnish-cache.org/trac/wiki/VCLExamples
- Public mailing lists: https://www.varnish-cache.org/trac/wiki/MailingLists
- Public IRC channel:
#varnish
atirc.linpro.no
Commercial:
- https://www.varnish-software.com/resources
- http://planet.varnish-cache.org
- https://www.varnish-software.com
- http://repo.varnish-software.com (for service agreement customers)
- support@varnish-software.com (for existing customers, with SLA)
- sales@varnish-software.com
Varnish Shared memory Log (VSL) tools:
varnishlog
varnishncsa
varnishhist
varnishtop
Administration:
varnishadm
Global counters:
varnishstat
Design and debug:
varnishtest
varnishlog
, varnishadm
and varnishstat
are explained in the Examining Varnish Server's Output chapter.
Next sections explain varnishtop
, varnishncsa
, and varnishhist
.$varnishtop -i BereqURL,RespStatus list length 5 trusty-amd64 7.20 RespStatus 200 5.26 RespStatus 404 0.86 BereqURL /test.html 0.68 BereqURL / 0.39 BereqURL /index.html
- Group tags and tag-content by frequency
varnishtop
groups tags and their content together to generate a sorted list of the most frequently appearing tag/tag-content pair.
This tool is sometimes overlooked, because its usefulness is visible after you start filtering.
The above example lists status codes that Varnish returns.
Two of the perhaps most useful variants of varnishtop
are:
varnishtop -i BereqURL
: creates a list of requested URLsx at the backend. Use this to find out which URL is the most fetched.varnishtop -i RespStatus
: lists what status codes Varnish returns to clients.
varnishtop
uses the varnishlog
API, therefore you may also combine tag lists as in the above example.
Even more, you may apply Query Language -q
options.
For example, varnishtop -q 'respstatus > 400'
shows you counters for responses where client seem to have erred.
Some other possibly useful examples are:
varnishtop -i ReqUrl
: displays what URLs are most frequently requested from clients.varnishtop -i ReqHeader -C 'User-Agent:.*Linux.*'
: listsUser-Agent
headers that contain the regular-expression and ignoring caseLinux
string. This example is useful to filter requests from Linux users, since most web browsers in Linux report themselves as Linux.varnishtop -i RespStatus
: lists status codes received in clients from backends.varnishtop -i VCL_call
: shows what VCL functions are used.varnishtop -i ReqHeader -I Referrer
shows the most common referrer addresses.
10.10.0.1 - - [24/Aug/2008:03:46:48 +0100] "GET \ http://www.example.com/images/foo.png HTTP/1.1" 200 5330 \ "http://www.example.com/" "Mozilla/5.0"
If you already have tools in place to analyze NCSA Common log format, varnishncsa
can be used to print the VSL in this format.
varnishncsa
dumps everything pointing to a certain domain and subdomains.
Filtering works similar to varnishlog
.
1:1, n = 71 localhost # # # # ## ### ### ### ### ### | ### | ### | | ### |||| ### # |||| #### # |##|##### # # # # # +-------+-------+-------+-------+-------+-------+-------+-------+------- |1e-6 |1e-5 |1e-4 |1e-3 |1e-2 |1e-1 |1e0 |1e1 |1e2
The varnishhist
utility reads the VSL and presents a continuously updated histogram showing the distribution of the last n requests.
varnishhist
is particularly useful to get an idea about the performance of your Varnish Cache server and your backend.
The horizontal axis shows a time range from 1e-6 (1 microsecond) to 1e2 (100 seconds). This time range shows the internal processing time of your Varnish Cache server and the time it takes to receive a response from the backend. Thus, this axis does not show the time perceived at the client side, because other factors such as network delay may affect the overall response time.
Hits are marked with a pipe character ("|
"), and misses are marked with a hash character ("#
").
These markers are distributed according to the time taken to process the request.
Therefore, distributions with more markers on the left side represent a faster performance.
When the histogram grows in vertical direction more than what the terminal can display, the 1:m rate changes on the left top corner. Where m represent the number of times that each marker is found. On the right top corner, you can see the name of the host.
- Send a few requests to Varnish using
http -p hH http://localhost/
- verify you have some cached objects using
varnishstat
- look at the communication with the clients, using
varnishlog
. Try sending various headers and see them appear invarnishlog
. - Install
siege
- Run
siege
againstlocalhost
while looking atvarnishhist
- Script driven program used to test the configuration of Varnish, run regression tests, and develop VMODs
- Useful for system administrators, web developers, and VMODs developers
Varnish is distributed with many utility programs.
varnishtest
is a script driven program that allows you create client mock-ups, simulate transactions, fetch content from mock-up or real backends, interact with your actual Varnish configuration and assert expected behaviors.
You can use varnishtest
when configuring your Varnish installation, i.e., writing VCL code, or developing VMODs.
varnishtest
has its own language: the Varnish Test Case (VTC) language.
This language has a fairly simple syntax.
In fact, when designing your caching algorithm or any other functionality in Varnish, we recommend you first to write Varnish Test Cases (VTCs) as part of your design.
VTCs are also useful to reproduce bugs when filing a bug report.
There are many .vtc
files included in Varnish Cache under bin/varnishtest/tests/
.
Think about those files as a learning source.
Further documentation of varnishtest
is found in its man page, bin/varnishtest/tests/README
and https://www.varnish-cache.org/docs/trunk/reference/varnishtest.html.
- Test against simulated or real backends
- Starts real instance of
varnishd
- Simulates clients
- Asserts using
expect
expect
supports regular expressions
b00001.vtc
varnishtest
does not follow the unit testing framework (up/test/assert/tear down) nor behavior-driven development (given/when/then).
Depending on your use case, there might be test preparations, executions and assertions all over the place.
VTC is not compiled but simply interpreted on the fly.
There is a naming convention for VTC files.
Files starting with b
as the example above contain basic functionality tests.
The naming scheme is in Varnish-Cache/bin/varnishtest/tests/README
or https://raw.githubusercontent.com/varnish/Varnish-Cache/master/bin/varnishtest/tests/README.
All VTC programs start by naming the test:
varnishtest "Varnish as Proxy"
In this example we declare a simulated origin server:
server s1 { rxreq txresp } -start
All server declarations must start with s
.
In the code above, s1
receives a request rxreq
, and transmits a response txresp
.
-start
boots s1
and makes available the macros ${s1_addr}
and ${s1_port}
with the IP address and port of your simulated backend.
You may also start a declaration at a later point in your code, for example server s1 -start
.
To declare an instance of your real Varnish server:
varnish v1 -arg "-b ${s1_addr}:${s1_port}" -start
varnish v1
declares an instance of your real Varnish server, i.e., varnishd
.
The names for Varnish servers must start with v
.
This instance is controlled by the manager process, and -start
forks a child, which is the actual cacher process.
You will learn about the manager and cacher in The Parent Process: The Manager and The Child Process: The Cacher sections.
There are many ways to configure varnishd
.
On way is by passing arguments with -arg
as in -arg "-b ${s1_addr}:${s1_port}"
.
-b
is a varnishd
option to define the backend.
In this case, we use the IP address and port of the simulated backend s1
, but you can also use a real backend.
Therefore, varnishtest
can be used as integration tool when testing your real backend.
There are other ways to define backends. The most common one is perhaps by defining them in your VCL code, as we shall see in the next section.
To simulate a client:
client c1 { txreq rxresp expect resp.http.via ~ "varnish" } -run
Simulated clients in varnishtest
start with c
.
In this example, c1
transmits one request and receives one response.
Since Varnish is a proxy, we expect to receive the response from the backend via Varnish.
Therefore, c1
expects varnish
in the via
HTTP header field.
We use tilde ~
as match operator of regular-expressions because the exact text in resp.http.via
depends on the Varnish version you have installed.
Finally, you start client c1
with the -run
command.
- Varnish is a multi-threaded program
- Use
-wait
as synchronization mechanism -run
:-start -wait
You might have noticed that we used -start
for v1
, but -run
for c1
.
The difference between these commands is that -run
executes -start -wait
.
Varnish is a multi-threaded program.
Therefore, each instance in varnishtest
, i.e., s1
, v1
and c1
, is executed by a different thread.
Sometimes, you will need some sort of synchronization mechanism to ensure you avoid race conditions or other non-intuitive behaviors.
For those cases, you can use the -wait
command.
-wait
tells the executor of varnishtest
to wait for a given instance to complete before proceeding to the next instruction in your VTC program.
To illustrate this, see the difference between:
varnishtest "Synchronized" server s1 { rxreq txresp } server s1 -start client c1 -connect ${s1_sock} { txreq rxresp } # -run: -start - wait client c1 -run server s1 -wait
and:
varnishtest "Unsynchronized" server s1 { rxreq txresp } server s1 -start -wait client c1 -connect ${s1_sock} { txreq rxresp } client c1 -run
The second test fails in comparison to the first one, because varnishtest
times out while waiting for s1
to receive a request and transmit a response.
Therefore, you typically start Varnish servers with the -start
command, but start clients with the -run
command.
Note
You will learn more about the Threading Model of Varnish in its own section.
Note
Note that we do not instantiate a Varnish server in the examples, but connect the client directly to the server.
For that purpose we use ${s1_sock}.
This macro translates to the IP address and port of s1
.
$varnishtest b00001.vtc # top TEST b00001.vtc passed (1.458)
To run your test, you simply issue the command above.
By default, varnishtest
outputs the summary of passed tests, and a verbose output for failed tests only.
If you want to always get a verbose output, run varnishtest
with the -v
option.
A passed test means that you have the most basic Varnish configuration correct in the testbed varnishtest
.
In the next section we explain how to configure Varnish in the way you normally would do after your tests have passed or when the varnishtest
testbed is not enough for your needs.
There is much more to explain about varnishtest
, but before that, you must learn more about the fundamentals of Varnish.
We will introduce new concepts and make a more advanced use of varnishtest
as we progress in the book.
- Use VTC to test the
Server
andVia
HTTP header fields.
expect
.
If you need help, take a look at Solution: Test Apache as Backend with varnishtest.vtc/b00003.vtc
Parameters can also be set in varnishtest
.
To execute commands via the CLI, you have three options: -cli "command"
, -cliok "command"
and -clierr "status" "command"
.
-cli
executes a command without checking the return status.
-cliok
executes a command and expects it to return OK 200 status.
-clierr
executes a command and checks whether the expected return status
matches.
Note
You have to instruct varnishtest
to assert the expected behavior as much as you can.
For example, varnish v1 -cli "param.set default_ttl -1"
does not fail because -cli
does not assert the return status.
Note
The macro ${bad_ip} translates to 192.0.2.255.
This IP address is for test use only, and it is used here because we do not need a backend to set parameters in Varnish.
However, we must always declare at least one backend when varnishd
is to be started.
Note
Note that we do not start v1
, because in this example, we do not need to start the cacher process.
vtc/b00004.vtc
You can use the delay
command in varnishtest
.
The unit of the command are seconds and it also accepts float numbers.
For more information about the Age
response header field refer to the Age subsection.
The Age
value depends on the time to live (TTL) value of the cached object.
We will learn more about it in The Initial Value of beresp.ttl section.
b00008.vtc
In Varnish, an expired object is an object that has exceeded the TTL + grace + keep
time.
In the example above, the Expires
header field sets TTL
to 1, and changes default_grace
from 10
to 2
.
default_keep
is already 0
, but we show it explicitly anyway.
Tip
Take a look at s00000.vtc
and s00001.vtc
in Varnish-Cache/bin/varnishtest/tests/
.
Tip
To get more information about n_expire
, issue man varnish-counters
.
$varnishtest -v b00001.vtc (...) **** v1 0.3 vsl| 0 CLI - Rd vcl.load "boot" (...) (...) **** v1 0.4 vsl| 1000 Begin c sess 0 HTTP/1 (...) **** v1 0.4 vsl| 1002 Begin b bereq 1001 fetch (...) **** v1 0.4 vsl| 1002 End b **** v1 0.4 vsl| 1001 Begin c req 1000 rxreq (...) **** v1 0.4 vsl| 1001 End c (...) **** v1 0.4 vsl| 1000 End c (...) **** v1 0.5 vsl| 0 CLI - EOF on CLI connection (...)
Above is a snippet of how Varnish logs are displayed in varnishtest
.
varnishtest
does not group logs by default as varnishlog
does.
Still, varnishtest
allows you to group the transactions for assertions with the command logexpect
.
varnishtest
starts client transactions in 1000
.
Note the VXID 0
for Varnish specific records.
- Allows you to assert log records
- Uses
varnishlog
API - Supports regular expressions
logexpect
is a program that uses the varnishlog
API.
Therefore, it is able to group and query the Varnishlog just as varnishlog
does.
In addition, logexpect
allows you to assert what you are expecting to appear in VSL.
Note logexpect l1 -wait
at the end of the VTC script above.
Without it, the test would finish successfully without concluding the assert in l1
, because varnishtest
would not wait for it.
-wait
instructs the executor of varnishtest
to wait until l1
is done.
Below is the synopsis of arguments and options of logexpect
:
-v <varnish-instance> -d <0|1> (head/tail mode) -g <grouping-mode> -q <query> vsl arguments (vsl_arg.c) -b Only display backend records -c Only display client records -C Caseless regular-expressions -i <taglist> Include tags -I <[taglist:]regex> Include by regex -L <limit> Incomplete transaction limit -T <seconds> Transaction end timeout logexpect lN -v <id> [-g <grouping>] [-d 0|1] [-q query] [vsl arguments] { expect <skip> <vxid> <tag> <regex> } skip: [uint|*] Max number of record to skip vxid: [uint|*|=] vxid to match tag: [tagname|*|=] Tag to match against regex: regular-expression to match against (optional) *: Match anything =: Match value of last successfully matched record
- Write a Varnish test to check the counters for cache misses, cache hits, and number of cached objects.
- Use
cache_miss
,cache_hit
, andn_object
counters respectively.
vtc/c00002.vtc
In c00002.vtc
, c1
requests /same-url
three times.
Since the backend s1
returns Vary: Foobar
, Varnish maps the cached object to both req.url
and http.foobar
.
Therefore, the second request misses the cached object and fetches from s1
a new variation mapped to Foobar: 2
.
The third request from c1
matches both req.url
and http.foobar
values from the first request.
Thus, this request does not trigger a backend request.
Recall that X-Varnish
contains the transaction ID of the client request and if applicable, the ID of the backend transaction that stored the object delivered.
You can see this behavior in the third request.
That also means that the VXID counting does not increase to 1006
in the third client request.
If your backend returns Vary:
, it must also handle situations when clients do not send the request header to identify a variation.
For example, when c1
does not send Footbar:
:
txreq -url "/same-url" rxresp
your backend should handle the lack of that header field specifically. You can test it as the following assertion shows:
rxreq expect req.http.foobar == <undef> txresp -hdr "Vary: Foobar" -hdr "Snafu: 3" -body "3333\n"
Be aware that the lack of a header field sent by a client is not the same as sending the field with an empty value. Therefore, requests like:
txreq -hdr "Foobar: "
should be handled in your backend specifically. You can test it as:
rxreq expect req.http.foobar == "" txresp -hdr "Vary: Foobar" -hdr "Snafu: 4" -body "4444\n"
c00002.vtc
is a modified version for teaching purposes from Varnish-Cache/bin/varnishtest/tests/c00004.vtc
.
We advise you to look at the many tests included in Varnish-Cache
.
Next we cover four important header fields used in conditional requests.
Two validator fields: ETag
and Last-Modified
; and two precondition header fields: If-None-Match
and If-Modified-Since
.
vtc/b00007.vtc
The example above is a modified version of Varnish-Cache/bin/varnishtest/tests/b00039.vtc
and it shows the usage of Last-Modified
and If-Modified-Since
header fields.
The example introduces how to insert VCL code in varnishtest
:
sub vcl_backend_response { set beresp.ttl = 2s; set beresp.grace = 5s; # beresp.was_304 is ``true`` if the response from the backend was # a positive result of a conditional fetch (``304 Not Modified``). set beresp.http.was-304 = beresp.was_304; }
You will learn all details about VCL in the following sections, but for now it is enough to understand that this code sets the time to live TTL and grace time of cached objects to 2 and 5 seconds respectively. Recall the object lifetime from Figure 2 to understand the expected behavior.
The code also adds a HTTP response header field was-304
with the boolean value of the beresp.was_304
.
This variable is set to true
if the response from the backend was a positive result of a conditional fetch (304 Not Modified
).
We hope that this exercise motivates you to use varnishtest
when designing your cache policies.
As you can see, varnishtest
is very precise when testing caching objects against different time settings.
Note
beresp.was_304
is a variable available in Varnish 4.1
b00009.vtc
The example above shows how Cache-control: max-age=3
overwrites TTL
for cached objects.
The default TTL
is 120 seconds, but we set it here to 1 just to explicitly show that the cached object is not expired after a delay of 2 seconds, because max-age=3
.
Therefore, the second assert:
expect resp.bodylen == 3
is 3 but not 6 (size of FOOBAR
).
If you are curious, you can remove:
-hdr "Cache-control: max-age=3"
from the first txresp
, and you will that the second request will contain a body length of 5.
Tip
Take a look at b00941.vtc
, b00956.vtc
and r01578.vtc
in Varnish-Cache/bin/varnishtest/tests/
to learn more.
vtc/b00000.vtc:
varnishtest
allows you to insert VCL code with the -vcl
directive when declaring a Varnish server.
This VCL code is inserted above the subroutines in built-in code in {varnish-source-code}/bin/varnishd/builtin.vcl
.
Since builtin.vcl
already includes vcl 4.0;
, you do not need to add it in varnishtest
.
varnishtest
allows you insert VCL code from an external file using the include "foo.vcl";
directive, or load VMODs using the import foo;
directive.
For examples on how to use include
and import
, refer to the available VTC files in your Varnish distribution under the directory varnish-cache-plus/bin/varnishtest/tests/
.
vtc/b00012.vtc
The example above is a modification of Varnish-Cache/bin/varnishtest/tests/b00036.vtc
.
In this VTC you can see how the second request of c1
is constructed out from the cached object.
After purging the implicit resource /
, the third request from c1
fetches a new object from s1
.
A quick way for you to double check the acl
authorization is by changing the IP address in it.
So you should see that the PURGE
request coming from localhost
will not pass the condition:
if (!client.ip ~ purgers)
client c1 { txreq -req BAN rxres } -run
PURGE
, BAN
and REFRESH
requests in varnishtest
, so your VCL program acts accordingly.
Remember that you still need specify the requested URL
in txreq
if the URL is other than root /
.
We advise you to search for purge
and ban
in Varnish-Cache/bin/varnishtest/tests/
to learn more on how to invalidate caches.Varnish-Cache/bin/varnishtest/tests/b00043.vtc:
Cache-Control
sets max-age
to ttl
and stale-while-revalidate
to grace
.
ttl
and grace
are attributes of cached objects.
The VCL code in v1
includes these attributes in the HTTP response header fields http.ttl
and http.grace
that are sent to the client.
c1
asserts the values of these fields.In this exercise you have to use two cache techniques; first Vary
and then hash_data
.
The exercise uses the Cookie
header field, but the same rules apply to any other field.
Vary: Part 1:
- Write a VTC program that forces Varnish to cache client requests with cookies.
- Send two client requests for the same URL; one for user Alice and one for user Bob.
- Does Varnish use different backend responses to build and deliver the response to the client?
- Make the your simulated server send the
Vary: Cookie
response header field, then analyze the response to the client. - Remove
beresp.http.Vary
in vcl_backend_response and see if Varnish still honors theVary
header.
Vary: Part 2:
- Purge the cached object for resource
/cookies.php
. - Check if it affects all, none or just one of the objects in cache (e.g: change the value of the cookie and see if the
PURGE
method has purged all of them).
hash_data(): Part 1:
- Write another VTC program or add conditions and asserts to differentiate requests handled by
Vary
andhash_data()
. - Add
hash_data(req.http.Cookie);
in vcl_hash. - Check how multiple values of
Cookie
give individual cached objects.
hash_data(): Part 2:
- Purge the cache again and check the result after using
hash_data()
instead ofVary: Cookie
.
Vary
and hash mechanisms.
After this exercise, you should have a very good idea on how Vary
and hash_data()
work.
If you need help, see Solution: Handle Cookies with Vary in varnishtest or Solution: Handle Cookies with hash_data() in varnishtest.Varnish-Cache/bin/varnishtest/tests/e00004.vtc:
e00004.vtc
shows how ESI substitution works.
When Varnish reads <!--esi <esi:include src="/body"/> -->
, it triggers a request with URL /body
.
The result of this request replaces the <!--esi -->
tag.
Since there are two different requests, one for the root /
resource and other for the /body
resource, you can handle their cached objects separately.
For example, you can set different TTLs for them or apply different invalidation policies.
We have counted the expected body length after the substitution and assert it in the VTC, but if you do not trust us, you can easily see the replacement by executing:
varnishtest -v e00004.vtc | grep "chunk|"
In the result:
**** c1 0.4 chunk| \n **** c1 0.4 chunk| \t\t<html>\n **** c1 0.4 chunk| \t\tBefore include\n **** c1 0.4 chunk| \t\t **** c1 0.4 chunk| \n **** c1 0.4 chunk| \t\tIncluded file\n **** c1 0.4 chunk| \t \n **** c1 0.4 chunk| \t\tAfter include\n **** c1 0.4 chunk| \t
you can see the HTML document after ESI has been processed.
This appendix contains code needed for some exercises.
- varnish3to4 is a script that assists you migrating a VCL file from Varnish 3 to 4.
- Download it from https://github.com/fgsch/varnish3to4
The script aims to replace most of the syntactical changes in VCL code from Varnish 3 to Varnish 4, but it is not exhaustive. That said, you should use it under your own responsibility.
You can download the script from https://github.com/fgsch/varnish3to4. Usage and up-to-date details about the script is at the same web address.
- VMOD basics
varnishtest
< Hello, World! > \ ^__^ \ (oo)\_______ (__)\ )\/\ ||----w | || ||
This appendix explains the concepts you should know to develop your own VMODs. The appendix takes you through the simplest possible VMOD: the Hello, World VMOD.
To learn most out of this appendix, you should have understood at least the following chapters of this book: Design Principles, Getting Started, VCL Basics, VCL Subroutines.
- What is a VMOD
- When to use in-line C or VMODs?
- The workspace memory model
varnishtest
A VMOD is a shared library with some C functions which can be called from VCL code.
The standard (std) VMOD, for instance, is a VMOD included in Varnish Cache.
We have already used the std VMOD in this book to check whether a backend is healthy by calling std.healthy()
.
VCL is the domain specific language of Varnish. This language is very powerful and efficient for most tasks of a cache server. However, sometimes you might need more functionalities, e.g., look up an IP address in a database.
VCL allows you to add inline C code, but this is not the most convenient approach. If you use the memory management API provided by Varnish, your VMODs are generally easier to maintain, more secure, and much easier to debug in collaboration with other developer. In addition, VMODs do not require to reload VCL files to take effect.
When writing VMODs, you should test them towards varnishtest
.
In fact, we recommend you first to write your tests as part of your design, and then implement your VMOD.
Therefore, we introduce next varnishtest
before proceeding with the implementation the VMOD itself.
- Script driven program used to test programs written in VCL and VMODs
With varnishtest
you can create mock-ups of clients and origin servers to interact with your Varnish installation.
This is useful to simulate transactions and provoke a specific behavior.
You can use varnishtest
when writing VCL code or VMODs.
varnishtest
is also useful to reproduce bugs when filing a bug report.
The best way to learn how to create Varnish tests is by running the ones included in Varnish Cache and then write your own tests based on them.
Tests of Varnish Cache are in bin/varnishtest/tests/
.
You should also take a look at the README file bin/varnishtest/tests/README
to learn about the naming convention.
helloworldtest.vtc:
varnishtest "Hello, World" server s1 { rxreq txresp } -start varnish v1 -vcl+backend { sub vcl_deliver { set resp.http.hello = "Hello, World"; } } -start client c1 { txreq -url "/" rxresp expect resp.http.hello == "Hello, World" } varnish v1 -expect cache_miss == 0 varnish v1 -expect cache_hit == 0 client c1 -run varnish v1 -expect cache_miss == 1 varnish v1 -expect cache_hit == 0 client c1 -run client c1 -run varnish v1 -expect cache_miss == 1 varnish v1 -expect cache_hit == 2
varnishtest
does not follow the unit testing framework (up/test/assert/tear down) nor behavior-driven development (given/when/then).
Depending on your use case, there might be test preparations, executions and assertions all over the place.
VTC is not compiled but simply interpreted on the fly.
When run, the above script simulates an origin server s1
, starts a real Varnish instance v1
, and simulates a client c1
.
server s1
declares a simulated origin server that receives a request rxreq
, and transmits a response txresp
.
The -start
directive makes an instance of that declaration to be started.
-start
can also be at a later point in your code as server s1 -start
.
varnish v1 -vcl+backend
declares an instance of your real Varnish server and loads the VCL code inside the brackets.
varnishtest
controls v1
through the manager process (see The Parent Process: The Manager).
The +backend
directive injects the backend (origin server s1
) to the VCL code.
Alternatively, you might want to add backends manually, for example:
varnish v1 -vcl { backend default { .host = "${s1_addr}"; .port = "${s1_port}"; } }
Once s1
is started, the macros ${s1_addr}
and ${s1_port}
with the IP address and port of your simulated backend are automatically made available.
Since varnishtest
launches a real varnishd
instance, it is possible to use a real backend instead of mock servers.
Thus, you can test your actual backend.
client c1
declares a simulated client that transmits a request txreq
for the slash URL: -url "/"
.
c1
receives a response rxresp
.
varnishtest
supports assertions with the keyword expect
.
For example, c1
expects the response header field resp.http.hello
with value Hello, World
.
Assertions can be inside the declaration of the origin server and client, but not inside the Varnish server.
Since Varnish is a proxy, checking requests and responses in it is irrelevant.
Instead, you have access to the counters exposed by varnishstat
at any time:
varnish v1 -expect counter == value
Assertions are evaluated by reading the shared memory log, which ensures that your assertions are tested against a real Varnish server.
Therefore, Varnish tests might take a bit longer than what you are used to in other testing frameworks.
Finally, client c1 -run
starts the simulated client c1
.
You will learn how to extend this script to test your VMOD later in this chapter, but before, run and analyze the output of helloworldtest.vtc
to understand varnishtest
better.
$varnishtest helloworldtest.vtc top TEST helloworldtest.vtc passed (1.554)
To run your test, you simply issue varnishtest helloworldtest.vtc
By default, varnishtest
outputs the summary of passed tests, and a verbose output for failed tests.
It is strongly recommended that you look at the verbose output to understand what happens under the hood.
For that, you run varnishtest
with the -v
option.
Later in this appendix, when testing VMODs, we will call make check
instead of typing varnishtest
in the command line.
make check
calls varnishtest
with the needed options.
Note
man varnishtest
shows you all options
- Build Varnish Cache from source
- Try
libvmod-example
VMODs require the source code from Varnish Cache that you are running.
The easiest way to be sure you have everything in place, is to build your Varnish Cache from source.
Although you can also develop VMODs against a Varnish installation from a package repository.
The git repository and building instructions are at https://github.com/varnish/Varnish-Cache.git
.
Once you have built Varnish Cache, build the libvmod-example
from https://github.com/varnish/libvmod-example by following the instructions in the repository.
When building the libvmod-example
, make sure that its branch matches with the branch version of Varnish-Cache.
For example, to build libvmod-example
against Varnish Cache 4.0, make sure that you checkout the branch 4.0 in both, the libvmod-example
and Varnish-Cache
.
Next, we explain the content inside libvmod-example
.
- VCC: VCL to C Compiler
vmod_example.vcc:
$Module example $Init init_function $Function STRING hello(STRING)
vcc_if.h:
struct VCL_conf; struct vmod_priv; /* Functions */ VCL_STRING vmod_hello(VRT_CTX, VCL_STRING); int init_function(struct vmod_priv *, const struct VCL_conf *);
In vmod_example.vcc
you declare the module name, initialization function and other functions you need.
Definitions are stored in files with .vcc
extension.
Please note the $
sign leading the definitions in the vmod_example.vcc
.
$Module example
The first line gives the name to the module.
$Init init_function
The second line declares an optional initial function, which is called when a VCL program loads this VMOD.
$Function STRING hello(STRING)
The third line declares the only function in this VMOD.
The source tree is based on autotools
to configure the building.
When you run the Makefile
,it passes vmod_example.vcc
to the script vmodtool.py
(included in Varnish Cache) and translates the VCC code to C.
The translation is stored in vcc_if.h
and vcc_if.c
, and since they are machine generated, you should not modify them.
The .vcc
file also contains the documentation that is used to generate the man page of your VMOD.
The documentation is parsed by vmodtool.py
and stored in src/vmod_example.man.rst
.
This RST file is then used to create the man page when compiling your VMOD.
We advise you to write the documentation of your VMOD in the .vcc
file, but if you prefer to have it in another location, such as the README.rst
file, you can change the source for documentation in Makefile.am
.
For example, change from:
vmod_example.3: src/vmod_example.man.rst
to:
vmod_example.3: README.rst
Next, you implement the hello
functions in the vmod_example.c
.
vmod_example.c:
VCL_STRING vmod_hello(const struct vrt_ctx *ctx, VCL_STRING name) { char *p; unsigned u, v; u = WS_Reserve(ctx->ws, 0); /* Reserve some work space */ p = ctx->ws->f; /* Front of workspace area */ v = snprintf(p, u, "Hello, %s", name); v++; if (v > u) { /* No space, reset and leave */ WS_Release(ctx->ws, 0); return (NULL); } /* Update work space with what we've used */ WS_Release(ctx->ws, v); return (p); }
WS_Reserve(ctx->ws, 0)
.
It is important to release the memory you used with WS_Release(ctx->ws, v)
, otherwise you are introducing a memory leak.Every worker thread has its own workspace ws
in virtual memory.
This workspace is a contiguous char array
defined in cache/cache.h
as:
struct ws { unsigned magic; #define WS_MAGIC 0x35fac554 char id[4]; /* identity */ char *s; /* (S)tart of buffer */ char *f; /* (F)ree/front pointer */ char *r; /* (R)eserved length */ char *e; /* (E)nd of buffer */ };
magic
and WS_MAGIC
are used for sanity checks by workspace functions.
The id
field is self descriptive.
The parts that most likely you are interested in are the SFRE
fields.
s
and e
point to the start and end of the char array
respectively.
f
points to the currently available memory, it can be seen as a head that moves forward every time memory is allocated.
f
can move up to the end of the buffer pointed by e
.
r
points to the reserved memory space of the workspace.
This space is reserved to allow incremental allocation.
You should remember to release this space by calling WS_Release(struct ws *ws, unsigned bytes)
once your VMOD does not need it any longer.
The cache/cache.h
is automatically included when you compile your .vcc
file.
Next, we describe in detail the headers that are included in vmod_example.c
.
#include "vrt.h" #include "cache/cache.h" #include "vcc_if.h"
The vrt.h
header provides data structures and functions needed by compiled VCL programs and VMODs.
cache.h
declares the function prototypes for the workspace memory model among others.
These functions are implemented in cache_ws.c
.
cache.h:
void WS_Init(struct ws *ws, const char *id, void *space, unsigned len); unsigned WS_Reserve(struct ws *ws, unsigned bytes); void WS_MarkOverflow(struct ws *ws); void WS_Release(struct ws *ws, unsigned bytes); void WS_ReleaseP(struct ws *ws, char *ptr); void WS_Assert(const struct ws *ws); void WS_Reset(struct ws *ws, char *p); char *WS_Alloc(struct ws *ws, unsigned bytes); void *WS_Copy(struct ws *ws, const void *str, int len); char *WS_Snapshot(struct ws *ws); int WS_Overflowed(const struct ws *ws); void *WS_Printf(struct ws *ws, const char *fmt, ...) __printflike(2, 3);
vcc_if.h
is generated out from the definitions in your .vcc
file.
This header contains the declaration of your VMOD functions in C code.
$./autogen.sh $./configure $make $make check #make install
- Examine how
libvmod_example
is imported insrc/tests/test01.vtc
The source tree is based on travis and Autotools to configure the building. More detailed building instructions are in: https://github.com/varnish/libvmod-example/blob/master/README.rst
Note that make check
calls varnishtest
with the needed options.
- Use
rename-vmod-script
to renamelibvmod-example
- Create tests
- Define and document functions in
vmod_cowsay.vcc
file - Implement functions in
vmod_cowsay.c
file make
,make check
andmake install
your VMOD
In this subsection you will learn how to build your own VMOD on top of libvmod-example
.
rename-vmod-script
prepares a basic VMOD that can be extended to your needs:
$./rename-vmod-script your_vmod_name
We have prepared a cowsay VMOD for you to follow easier this subsection, but you can create your own VMOD from scratch as we explain further. The cowsay VMOD adds the output of the Linux program, which generates ASCII pictures of a cow or a different animal with a message. You can download the code of the cowsay VMOD from https://github.com/aondio/libvmod-cowsay.git.
test01.vtc:
varnishtest "Test cowsay header" server s1 { rxreq txresp } -start varnish v1 -vcl+backend { import cowsay from "${vmod_topbuild}/src/.libs/libvmod_cowsay.so"; sub vcl_recv { if (req.url ~ "/cowsay") { set req.http.x-cow = cowsay.cowsay_canonical(); } } sub vcl_deliver { set resp.http.x-cow = req.http.x-cow; } } -start client c1 { txreq -url "/cowsay" rxresp expect resp.http.x-cow == "Cowsay: Hello World!" } -run
Snippet of test02.vtc:
sub vcl_recv { if (req.url ~ "/cowsay") { return(synth(700, "OK")); } } sub vcl_synth { if (resp.status == 700) { set resp.status = 200; set resp.http.Content-Type = "text/plain; charset=utf-8"; synthetic(cowsay.cowsay_vsb()); return (deliver); } } ... client c1 { txreq -url "/cowsay" rxresp expect resp.body == {** mybody ** ^__^ (oo)\_______ (__)\ )\/\ ||----w | || || } } -run
Snippet of test03.vtc:
sub vcl_recv { if (req.url ~ "/cowsay" || req.url ~ "/bunny") { return(synth(700, "OK")); } } sub vcl_synth { if (resp.status == 700) { set resp.status = 200; set resp.http.Content-Type = "text/plain; charset=utf-8"; if (req.url ~ "/cowsay"){ synthetic(cowsay.cowsay_friends("cow", "moo")); } if (req.url ~ "/bunny"){ synthetic(cowsay.cowsay_friends("bunny", "Varnish")); } return (deliver); } } ... client c1 { txreq -url "/cowsay" rxresp expect resp.body == {** moo ** ^__^ (oo)\_______ (__)\ )\/\ ||----w | || || } } -run client c2 { txreq -url "/bunny" rxresp expect resp.body == {** Varnish ** (\/) (..) (")(") } } -run
We advise you to start designing your tests.
test01.vtc
, test02.vtc
and test03.vtc
are examples in https://github.com/franciscovg/libvmod-cowsay.git.
test01.vtc
shows how the HTTP response header field is assigned.
When client c1
requests the /cowsay
URL, Varnish server v1
assigns the output of the VMOD function cowsay_canonical()
to the HTTP request header field req.http.x-cow
.
test02.vtc
shows how to alter the message body in the vcl_synth
subroutine.
In this second test, we use cowsay.cowsay_vsb()
, which return the cowsay ASCII picture.
The important difference between cowsay_canonical()
and cowsay.cowsay_vsb()
is the library used to manipulate the returned string.
We discuss this difference later in this section.
test03.vtc
reuses most of test02.vtc
.
test03.vtc
replaces cowsay.cowsay_vsb()
for cowsay.cowsay_friends(arg1, arg2)
, and adds some basic conditions.
cowsay.cowsay_friends()
returns the ASCII figure given in arg1
, which utters arg2
.
After the design of your tests, you declare the functions in the .vcc
file and implement them in the .c
file.
- Add more assertions using the keyword
expect
to check values of Varnish counters
$Function STRING cowsay_canonical() $Function STRING cowsay_vsb() $Function STRING cowsay_friends(STRING, STRING)
cowsay_canonical()
uses the canonical string library, and cowsay_vsb()
uses the Varnish String Buffer string library.
The VSB library is very useful to manipulate strings.
Therefore we recommend you to use it instead of the canonical string libraries.
Note
Although VCL allows it, we do not recommend to assign multiple lines to HTTP context header fields.
int init_function(struct vmod_priv *priv, const struct VCL_conf *conf) { /* init global state valid for the whole VCL life */ cow = "\n ^__^\n" " (oo)\\_______\n" " (__)\\ )\\/\\\n" " ||----w |\n" " || ||\n"; /* this 'cow' is now available for every other functions that will be defined in this vmod */ return (0); }
VCL_STRING vmod_cowsay_friends(VRT_CTX, VCL_STRING animal, VCL_STRING talk) { unsigned u; struct vsb *vsb; u = WS_Reserve(ctx->ws, 0); vsb = VSB_new(NULL, ctx->ws->f, u, VSB_AUTOEXTEND); if(!strcmp(animal, "cow")) { VSB_printf(vsb, "** %s **\n", talk); VSB_cat(vsb, cow); } if(!strcmp(animal, "bunny")) { VSB_printf(vsb, "** %s **\n", talk); VSB_cat(vsb, baby_bunny()); } VSB_finish(vsb); WS_Release(ctx->ws, VSB_len(vsb) + 1); return (vsb->s_buf); }
We explain here two relevant functions in this file.
The first is the init_function()
, where we declare a global variable holding the cow figure.
The second part is the vmod_cowsay_friends()
function, where we use string manipulation functions provided by VSB.
vmod_cowsay_vsb()
is a simplified version of vmod_cowsay_friends()
.
The implementation of cowsay_canonical()
is practically the same as vmod_hello()
.
Finally, it is time to make
, make check
and make install
your VMOD.
Note that make check
calls varnishtest
with the needed options.
The best way to learn more about VMODs is by writing them and seeing how others VMOD works. There are many VMODs written by the Varnish community and Varnish Software. Please take a look at the list in https://www.varnish-cache.org/vmods.
In addition, you can also look at the following blogs, which were used, besides other sources, to write this section:
- VAV
- Varnish Arg Vector -- Argv parsing.
- VBE
- Varnish Back End -- Code for contacting backends (bin/varnishd/cache_backend.c)
- VBP
- Varnish Backend Polling -- Health checks of backends (bin/varnishd/cache_backend_poll.c)
- VCA
- Varnish Connection Acceptor -- The code that receives/accepts the TCP connections (bin/varnishd/cache_acceptor.c)
- VCC
- VCL to C Compiler -- The code that compiles VCL to C code. (lib/libvcl)
- VCL
- Varnish Configuration Language -- The domain-specific programming language used for configuring a varnishd.
- VCT
- Varnish CType(3) -- Character classification for RFC2616 and XML parsing.
- VDD
- Varnish (Core) Developer Day -- Quarterly invite-only meeting strictly for Varnish core (C) developers, packagers and VMOD hackers.
- VEV
- Varnish EVent -- library functions to implement a simple event-dispatcher.
- VGB
- Varnish Governing Board -- May or may not exist. If you need to ask, you are not on it.
- VGC
- Varnish Generated Code -- Code generated by VCC from VCL.
- VIN
- Varnish Instance Naming -- Resolution of -n arguments.
- VLU
- Varnish Line Up -- library functions to collect stream of bytes into lines for processing. (lib/libvarnish/vlu.c)
- VRE
- Varnish Regular-Expression -- library functions for regular-expression based matching and substring replacement. (lib/libvarnish/vre.c)
- VRT
- Varnish Run Time -- functions called from compiled code. (bin/varnishd/cache_vrt.c)
- VRY
- VaRY -- Related to processing of Vary: HTTP headers. (bin/varnishd/cache_vary.c)
- VSL
- Varnish Shared memory Log -- The log written into the shared memory segment for varnish{log,ncsa,top,hist} to see.
- VSB
- Varnish string Buffer -- a copy of the FreeBSD "sbuf" library, for safe string handling.
- VSC
- Varnish Statistics Counter -- counters for various stats, exposed via varnishapi.
- VSS
- Varnish Session Stuff -- library functions to wrap DNS/TCP. (lib/libvarnish/vss.c)
- VTC
- Varnish Test Code -- a test-specification for the varnishtest program.
- VTLA
- Varnish Three Letter Acronym -- No rule without an exception.
- VUG
- Varnish User Group meeting -- Half-yearly event where the users and developers of Varnish Cache gather to share experiences and plan future development.
- VWx
- Varnish Waiter 'x' -- A code module to monitor idle sessions.
- VWE
- Varnish Waiter Epoll -- epoll(2) (linux) based waiter module.
- VWK
- Varnish Waiter Kqueue -- kqueue(2) (freebsd) based waiter module.
- VWP
- Varnish Waiter Poll -- poll(2) based waiter module.
- VWS
- Varnish Waiter Solaris -- Solaris ports(2) based waiter module.
- Install Apache. We will use it as backend.
- All commands are executed as
root
user
To install Apache in Ubuntu or Debian, type the command:
$ apt-get install apache2
For CentOS, RHEL or Fedora:
$ yum install httpd
curl
is the tool typically used to transfer data from or to a server, but you might want to use something else, like HTTPie
, which has a very pretty color printing in the terminal.
To install HTTPie in Ubuntu or Debian:
$ apt-get install httpie
Next:
Verify that Apache works by typing
http -h localhost
. You should see a200 OK
response from Apache.Change Apache's port from 80 to 8080. In Ubuntu or Debian, you do this in
/etc/apache2/ports.conf
and/etc/apache2/sites-enabled/000-default.conf
. In CentOS, RHEL or Fedora, edit/etc/httpd/conf/httpd.conf
.Restart Apache. In Ubuntu or Debian type
service apache2 restart
. In CentOS, RHEL or Fedora:$ systemctl enable httpd.service $ apachectl start
Verify that Apache listens on port
8080
:http -h localhost:8080
This appendix contains the solutions of exercises throughout the book.
- Solution for systemd Ubuntu and Debian
- Solution for systemd Fedora/RHEL7+/CentOS 7+
Varnish is already distributed in many package repositories, but those packages might contain an outdated Varnish version. Therefore, we recommend you to use the packages provided by varnish-software.com for Varnish Cache Plus or varnish-cache.org for Varnish Cache. Please be advised that we only provide packages for LTS releases, not all the intermediate releases. However, these packages might still work fine on newer releases.
All software related to Varnish Cache Plus including VMODs are available in RedHat and Debian package repositories. These repositories are available on http://repo.varnish-software.com/, using your customer specific username and password.
All the following commands are for systemd Ubuntu or Debian and must be executed with root permissions.
First, make sure you have apt-transport-https
:
$ apt-get install apt-transport-https
To use the varnish-software.com repository and install Varnish Cache Plus 4.0 or 4.1 on Ubuntu 14.04 trusty:
$ curl https://<username>:<password>@repo.varnish-software.com/GPG-key.txt \ | apt-key add -
To use the varnish-cache.org repository and install Varnish Cache 4.0 or 4.1 on Ubuntu 14.04 trusty:
$ curl https://repo.varnish-cache.org/ubuntu/GPG-key.txt | apt-key add - $ echo "deb https://repo.varnish-cache.org/ubuntu/ trusty varnish-4.0" >> \ /etc/apt/sources.list.d/varnish-cache.list
If you are installing Varnish Cache 4.1, replace varnish-4.0
for varnish-4.1
in the command above.
If you are installing Varnish Cache Plus 4.0 or 4.1, add the repositories for VMODs in /etc/apt/sources.list.d/varnish-4.0-plus.list
or /etc/apt/sources.list.d/varnish-4.1-plus.list
respectively:
# Remember to replace 4.x, DISTRO and RELEASE with what applies to your system. # 4.x=(4.0|4.1) # DISTRO=(debian|ubuntu), # RELEASE=(precise|trusty|wheezy|jessie) # Varnish Cache Plus 4.x and VMODs deb https://<username>:<password>@repo.varnish-software.com/DISTRO RELEASE \ varnish-4.x-plus # non-free contains VAC, VCS and proprietary VMODs. deb https://<username>:<password>@repo.varnish-software.com/DISTRO RELEASE \ non-free
Re-synchronize the package index files of your repository:
$ apt-get update
To install Varnish Cache Plus and VMODs:
$ apt-get install varnish-plus $ apt-get install varnish-plus-addon-ssl $ apt-get install varnish-plus-vmods-extra
To install Varnish-Cache:
$ apt-get install varnish
Finally, verify the version you have installed:
$ varnishd -V
To use Varnish Cache Plus 4.0 or 4.1 repositories on systemd Fedora/RHEL7+/CentOS 7+, put the following in /etc/yum.repos.d/varnish-4.0-plus.repo
or /etc/yum.repos.d/varnish-4.1-plus.repo
, and change 4.x
for the version you want to install:
[varnish-4.x-plus] name=Varnish Cache Plus baseurl=https://<username>:<password>@repo.varnish-software.com/redhat /varnish-4.x-plus/el$releasever enabled=1 gpgcheck=0 [varnish-admin-console] name=Varnish Administration Console baseurl= https://<username>:<password>@repo.varnish-software.com/redhat /vac/el$releasever enabled=1 gpgcheck=0
Then, execute the following:
$ yum update $ yum install varnish-plus $ yum install varnish-plus-vmods-extra
Finally, verify the version you have installed:
$ varnishd -V
Note
More details on Varnish Plus installation can be found at http://files.varnish-software.com/pdfs/varnish-cache-plus-manual-latest.pdf
vtc/b00002.vtc
vtc/b00005.vtc
vtc/b00006.vtc
In this example, we introduce -vcl+backend
and feature
in VTC.
-vcl+backend
is one way to pass inline VCL code and backend to v1
.
In this example, v1
receives no inline VCL injects declaration of the backend s1
.
Thus, -vcl+backend{}
is equivalent to -arg "-b ${s1_addr}:${s1_port}"
in this case.
feature
checks for features to be present in the test environment.
If the feature is not present, the test is skipped.
SO_RCVTIMEO_WORKS
checks for the socket option SO_RCVTIMEO
before executing the test.
b00006.vtc
is copied from Varnish-Cache/bin/varnishtest/tests/b00023.vtc
We advise you to take a look at the many tests under Varnish-Cache/bin/varnishtest/tests/
.
You will learn so much about Varnish when analyzing them.
VCL code:
vcl 4.0; backend default { .host = "127.0.0.1"; .port = "8080"; } sub vcl_recv { if (req.url ~ "^/admin") { return(pass); } }
Command to compile and visualize result in less
:
varnishd -C -f recv.vcl 2>&1 | less
In this suggested solution, the backend is configured to a local IP address and port. Since we are not running this code, you can configure it as you want.
Note the use of the match comparison operator ~
in regular expression.
In the output of the compiler you should be able to find your VCL code and the built-in VCL code appended to it.
- Use
varnishadm param.set
to set the value ofthread_pool_min
andthread_pool_max
. - Remember that the values are per thread pool, the default value for
thread_pools
is 2. - Monitor the MAIN.threads counter in
varnishstat
to see how many threads are running while performing this exercise.
c00001.vtc
The test above shows you how to set parameters in two ways; passing the argument -p
to varnishd
or calling param.set
.
-p vsl_mask=+WorkThread
is used to turn on WorkThread
debug logging.
The test proves that varnishd
starts with the number of threads indicated in thread_pool_min
.
Changes in thread_pool_min
and thread_pool_max
are applied by the thread herder, which handles the thread pools and adds or removes threads if necessary.
To learn more about other maintenance threads, visit https://www.varnish-cache.org/trac/wiki/VarnishInternals.
c00001.vtc
is a simplified version of Varnish-Cache/bin/varnishtest/tests/r01490.vtc
.
sub vcl_recv { set req.http.x-host = req.http.host; set req.http.x-url = req.url; set req.http.host = regsub(req.http.host, "^www\.", ""); /* Alternative 1 */ if (req.http.host == "sport.example.com") { set req.http.host = "example.com"; set req.url = "/sport" + req.url; } /* Alternative 2 */ if (req.http.host ~ "^sport\.") { set req.http.host = regsub(req.http.host,"^sport\.", ""); set req.url = regsub(req.url, "^", "/sport"); } }
You can test this solution via HTTPie or varnishtest
.
Using HTTPie:
http -p hH --proxy=http:http://localhost sport.example.com/index.html
Then you verify your results by issuing the following command and analyzing the output:
varnishlog -i ReqHeader,ReqURL
varnishtest
solution:
// Suggested solution A sub vcl_recv { if (req.url ~ "^/index\.html" || req.url ~ "^/$") { return(pass); } } // Suggested solution B sub vcl_backend_response { if (bereq.url ~ "^/index\.html" || bereq.url ~ "^/$") { set beresp.uncacheable = true; } }
vcl_recv
.
The usage of bereq.uncacheable
in vcl_backend_fetch
creates a hit-for-pass object.
See the hit-for-pass section for detailed description about this type of object.s-maxage
and handles .jpg
and .html
files to make them cacheable for 30 and 10 seconds respectively.
If s-maxage
is present with a positive TTL, we consider the response cacheable by removing beresp.http.Set-Cookie
.vcl/customized_error.vcl
The suggested solution forces a 503
error by misconfiguring .port
in the default backend.
You can also force a 503 response by using ${bad_ip}
in varnishtest
.
The macro ${bad_ip}
translates to 192.0.2.255.
vtc/b00011.vtc
Note that in the proposed solution the client receives a 200
response code.
purgearticle.php
solution-purge-from-backend.vcl
vtc/c00003.vtc
Vary
and hash_data()
might behave very similar at first sight and they might even seem like alternatives for handling cookies.
However, cached objects are referenced in different ways.
If Varnish is forced to store responses with cookies, Vary
ensures that Varnish stores resources per URL and Cookie.
If Vary: Cookie
is used, objects are purged in this way:
txreq -req PURGE -url "/cookie.php"
but something different is needed when using hash_data(req.http.Cookie)
, as you can see it in the next suggested solution.
vtc/c00004.vtc
hash_data(req.http.Cookie)
adds the request header field Cookie
to the hash key.
So Varnish can discern between backend responses linked to a specific request header field.
To purge cached objects in this case, you have to specify the header field used in hash_data()
:
txreq -req PURGE -url "/cookie.php" -hdr "Cookie: user: Alice"
vcl/solution-vcl_fetch-masquerade-ajax-requests.vcl
Note that the getMasqueraded()
works now after being processed in vcl_recv()
.