-
Notifications
You must be signed in to change notification settings - Fork 4
/
00_Prerequisite info.txt
66 lines (55 loc) · 2.55 KB
/
00_Prerequisite info.txt
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
## Ender 7 Machine Info (prior to Klipper install)
- Board: Creality CR-FDM-v2.4.S1_v101
- Power input: 24v
- Processor: ARM® Cortex®-M3 STM32F1 Microcontroller IC 32-Bit Single-Core 72MHz 512KB (512K x 8) FLASH
- STM32F103RET6
- 32bit
### Ender-7 (Marlin 1 - Command Output)
M503 # Report Settings
Recv: G21 ; Units in mm (mm)
Recv:
Recv: M200 S0 D1.75 #M200 - Set Filament Diameter
Recv: M92 X200.00 Y200.00 Z400.00 E140.00 #M92 - Set Axis Steps-per-unit
Recv: M203 X500.00 Y500.00 Z10.00 E60.00 #M203 - Set Max Feedrate
Recv: M201 X500.00 Y500.00 Z100.00 E5000.00 #M201 - Print Move Limits
Recv: M204 P500.00 R1000.00 T500.00 #M204 - Set Starting Acceleration
Recv: M205 B20000.00 S0.00 T0.00 X8.00 Y8.00 Z0.40 E5.00 #M205 - Set Advanced Settings [B -Minimum segment time (µs)][S -Minimum feedrate for print moves (units/s)][T -Minimum feedrate for travel moves (units/s)][X -X max jerk (units/s)][Y -Y max jerk (units/s)][Z -Z max jerk (units/s)][E -E max jerk (units/s)]
Recv: M206 X0.00 Y0.00 Z0.00 #M206 - Set Home Offsets
Recv: M420 S1 Z10.00 #M420 - Bed Leveling State [S -Set enabled or disabled][Z -Set Z fade height (Requires ENABLE_LEVELING_FADE_HEIGHT)]
Recv: M301 P12.50 I0.70 D60.00 #M301 - Set Hotend PID [P -Proportional value][I -Integral value][D -Derivative value]
Recv: M304 P327.11 I19.20 D1393.45 #M304 - Set Bed PID
Recv: M413 S0 #M413 - Power-loss Recovery
Recv: M851 X30.00 Y27.00 Z-2.60 #M851 - XYZ Probe Offset
### CR-FDM-v2.4.S1_v101 Pinout (hardware names)
- [! preceding name to indicate reverse polarity] [^ preceding hardware pull-up resistor] [~ preceding hardware pull-down resistor]
[stepper_x]
step_pin: PC2
dir_pin: PB9
enable_pin: !PC3
endstop_pin: ^PA5
[stepper_y]
step_pin: PB8
dir_pin: !PB7
enable_pin: !PC3
endstop_pin: ^PA6
[stepper_z]
step_pin: PB6
dir_pin: PB5
enable_pin: !PC3
endstop_pin: ^PA7
[extruder]
step_pin: PB4
dir_pin: !PB3
enable_pin: !PC3
heater_pin: PA1
sensor_pin: PC5
[heater_bed]
heater_pin: PA15
sensor_pin: PC4
[fan]
pin: PA0
[filament_switch_sensor filament_sensor]
switch_pin: !PA4
[bltouch]
sensor_pin: ^PB1
control_pin: PB0