An IEEE 802.11 packet injector and analyzer software📡
Use it with -radar!
🔧For GNU/Linux:
git clone https://github.com/ANDRVV/gapcast.git
cd gapcast
go build -buildvcs=false
./gapcast -i <interface>
The Injection table is a table where you can insert data and perform an attack or injection.
Advantages:
- You don't need to specify the channel.
- You don't need to specify the BSSID.
- Multiple synchronized attacks.
- Quick and easy attack initialization.
- Interface with attack information.
For more info click here.
The Single Deep Scanning feature focuses on a single target, splitting the scan into three phases. By using the BSSID alone, you can obtain a wide range of information.
Step 1: detect the channel of the AP or STA.
Step 2: collects the packets that are exchanged.
Step 3: arrange the data and calculate the distance based on different antennas.
For more info click here.
🚀Soon be updated! It will give more stuff!
By utilizing the INJ Table, you can initiate Evil Twin mode. After selecting the appropriate parameters, the attack will commence. One adapter, if available, will deauthenticate the victim's AP, while the second adapter will establish a rogue AP equipped with a Captive Portal system. This setup allows for the collection of credentials if the LogIn page templates are configured.
For more info click here.
For each driver there is a correct sequence of commands to start the network card correctly in monitor mode. Drivers supported by gapcast can also have a txpower modification, bug fixing etc. If the driver is not supported, it will start monitor mode directly with airmon-ng.
Supported drivers:
RTL88XXAUmon+txpowerR8187mon+bugfixRTL8812CUmonRTL8821CUmon
Important
If your driver is not supported or if you would like to boot into monitor mode with your changes, just do so before starting gapcast. If gapcast recognizes that the interface has already set monitor mode, it will not make any changes or even try to restart monitor mode.
./gapcast -i <iface> -2.4+5g -dNote
Scans all 2.4/5 Ghz channels disabling shifting of inactive devices.
./gapcast -i <iface> -2.4+5g -c 10,36 -p 03:e9:58:65:2a:8Note
Access Point that have 5 Ghz and 2.4 Ghz transmit via 2 different addresses, the address for 5 Ghz and the one for 2.4 Ghz. In most cases these 2 addresses have a Mac address with a very similar prefix:
In this case of selecting channel 10 for 2.4 Ghz and channel 36 for 5 Ghz with -c <channel> uses 2 channels with different bands, using -2.4+5g. Taking into consideration an Access Point that has the 5 Ghz address 03:e9:58:65:2a:8e and the 2.4 Ghz address 03:e9:58:65:2a:86, the common prefix is 03:e9:58:65:2a:8, which is set via -p <mac-prefix>.
With this parameter only devices with that specified prefix will be displayed.
./gapcast -i <iface> -2.4+5g -radarNote
Scan all 2.4/5 Ghz channels showing the approximate radius of the location in meters with the -radar parameter using the RadarRSSI library, more info.
./gapcast -i <iface>Note
Scans all 2.4 channels.
./gapcast -i <iface> -5gNote
Scans all 5 Ghz channels adding -5g parameter.
./gapcast -i <iface> -2.4+5g -w out.pcapNote
Scans all 2.4/5 Ghz channels, recording it and saving to a pcap file. Registration can be done by adding the -w <file>.pcap parameter.
./gapcast -i <iface> -c 11 -b a3:65:1b:56:7e:3c -w out.pcapNote
Scan only AP's channel (11) to get the best WPA 4-Way Handshake, To deauthenticate you need to open the gapcast injection table by pressing [CTRL-P], then select the De-Auth type, enter the required information and start the attack by pressing CTRL-D key for a few seconds (check that clients are present via the light-blue bar), as soon as the CTRL-D key is deactivated, the clients that reconnect to the Access Point:
Will send and receive EAPOL packets which you will record and save with the -w <file>.pcap parameter.
./gapcast -l out.pcapNote
If you want to restore data from a previous scan, done with gapcast, wireshark or other tools and load them on the gapcast table to better analyze the data, just insert the -l <file>.pcap parameter, if you want to restore the data and continue the scan you must add the -i <iface> parameter and/or add other additional parameters.
./gapcast -i <iface> -2.4+5g -beacon Note
If you want to show or record only the Access Points you must enter the -beacon parameter. For this technique, where we show all Access Points of all channels it is necessary to add the parameter -2.4+5g.
💻Happy hacking!😊
Caution
You must install apache2, iptables, hostapd, dnsmasq, aircrack-ng, php, if you'd use gapcast!
- New attack from INJ Table