An mpv script that automatically pauses before and/or after each subtitle line. Mostly intended for language learning.
(none): toggle auto-pause at start of line (toggle-start)n: toggle auto-pause at end of line (toggle-end)Alt+r: skip next pause (skip-next)Ctrl+r: replay active/last line, always available (replay)
To use a key binding other than the defaults above add a line like the
following to your input.conf (where X is the binding and <action_id>
is the value in parentheses in the list above):
X script-binding sub_pause/<action_id>
sub-pause-toggle-start doesn't have a default binding and must be assigned
manually.
If you want a binding for both replaying and skipping add a line like this:
Ctrl+Alt+SPACE script-binding sub-pause-replay; script-binding sub-pause-skip-next
sub_pause/ can be left out, however events triggered from bindings defined
without it will be sent to all scripts, which can lead to conflicts if two
scripts use the same action ID.
When using scoped actions, the script ID before / is derived from script's
filename, with the extension removed and all characters except alphanumeric
ASCII characters (A-Z, a-z, 0-9) replaced by _.
Create a file at script-opts/sub_pause.conf in your mpv config directory:
# To set a value remove the leading # and modify it after the =.
# All values given here are defaults. Seconds can be decimal values.
# if set to 'yes', enable pausing at the start of each line by default
#default_start=no
# if set to 'yes', enable pausing at the end of each line by default
#default_end=no
# pause roughly this many seconds before the end of each line
# very low values can result in the line no longer being active after pausing
#end_delta=0.1
# if autopausing is enabled, hide subtitles while not paused
#hide_while_playing=no
# automatically resume playback this many seconds after autopausing
# no effect if less than or equal to zero
#unpause_time=0
# if unpause_time is set, prevent the next automatic unpause by pressing this key
# can be anything that would be an acceptable key binding in mpv's input.conf
#unpause_override=SPACE
# if set to 'yes' (the default), the previous line will be replayed after
# invoking `replay` if there is currently no active line
#replay_prev=yes
If there are multiple subtitles visible at the same time (e.g. one at the top and one at the bottom, or on-screen text with SubStation Alpha(ASS) subs) the script will only pause at the end of the last visible line. While it would be possible to fix this at least some of the time by saving every change in the subtitle end time this(in my opinion) doesn't justify the additional complexity considering how rare such situations are.
If you come across any other problems while using the script feel free to open a GitHub issue or send a pull request.
This script allows automatically skipping parts of a video that don't contain any subtitles. Skipping can be done either by speeding up playback while no subtitles are present or by seeking to the start of the next subtitle line, skipping the interval between lines entirely.
The script works by briefly changing subtitle delay so that the next line starts at the current video/audio time, recording the difference between the original and shifted subtitle delay and then speeding up or seeking to the start of the next line (calculated from the difference).
This works best if mpv is forced to always demultiplex enough of the video for
the next subtitle line to be almost always available by setting
demuxer-readahead-secs to a value between 60-120 in mpv.conf.
Alternatively, enabling cache for all videos with cache=yes also works.
If demuxer readahead or cache are not set explicitly it is possible for the next subtitle line to be unavailable even if it starts within the next few seconds. The script can deal with this but works best if one of the config entries from above is set.
Ctrl+n: activate skipping (toggle)Ctrl+Alt+n: toggle between speedup and seek skip (switch-mode)Ctrl+Alt+[: decrease skip speed by 0.1 (decrease-speed)Ctrl+Alt+]: increase skip speed by 0.1 (increase-speed)Ctrl+Alt+-: decrease skip interval by 0.25s (decrease-interval)Ctrl+Alt++: increase skip interval by 0.25s (increase-interval)
When changing the interval using the numpad +/- keys, it might be necessary to also press shift, even if it's not part of the binding.
As explained for sub-pause, additional bindings can be assigned in input.conf:
X script-binding sub_skip/<action_id>
Create a file at script-opts/sub_skip.conf in your mpv config directory:
# To set a value remove the leading # and modify it after the =.
# All values given here are defaults. Seconds can be decimal values.
# if set to 'yes', enable skipping by default
#default_state=no
# if set to 'yes', use seek mode by default
#seek_mode_default=no
# any interval between subtitle lines longer than this value in seconds will be skipped
#min_skip_interval=3
# what speed to use while skipping if not in seek mode
#speed_skip_speed=2.5
# how many seconds after the end of a line to wait for before starting to skip
#lead_in=0
# how many seconds before the start of the next line to stop skipping at
#lead_out=1
# how much to change skip speed by when invoking sub-skip-{de,in}crease-speed
#speed_skip_speed_delta=0.1
# how many seconds to change the minimum interval by when invoking sub-skip-{de,in}crease-interval
#min_skip_interval_delta=0.25
sub-skip is inspired by and partially based on speed-transition from
https://github.com/zenyd/mpv-scripts, but rewritten from scratch.
