Re-Factored Version 1.1 (13 March, 2023)

This release supercedes version 61F_220622_v1, returning the colour scheme to the black/grey/red of the original CF6.1 UI.

The release notes below are copied from 61F_220622_v1, where they remain valid, & updated to capture the small differences.

This video playlist provides a high-level tour of the refactored v1 UI: https://youtube.com/playlist?list=PLfDSKnF0RNcbOUwW6B4rZagRsRP6l_rQg Except for the colour scheme, those videos remain valid.

PLEASE READ THE README FILE BEFORE FLASHING THIS FIRMWARE TO YOUR PRINTER.

Flashing the DWIN_SET in this release installs a TouchScreen firmware that works with the CF6.1-Final motherboard firmware and runs on any version of DGUS2 (Kerning problems may appear in some early versions.)

If you already have the CR6Community Firmware running on DGUS2 v3.5 on your printer, then you do not need to flash this firmware.

If you have DGUS2 v 4.4 or less flashed to your display, but not v3.5, then you MUST flash the kernel upgrade files to your display to install v3.5, if you wish to use the original CF6.1 Touchscreen firmware OR you can install this refactored DWIN_SET to your display.

If you have DGUS2 v4.5 or higher flashed to your display, you must flash this DWIN_SET instead of the one bundled with the motherboard firmware.

If you do flash this refactored firmware, you will benefit from the new features, but CR6-MAX users will lose one cosmetic feature:

NEW IN THE RE-FACTORED RELEASE:

• The last captured thermistor temperature values have been added to the three thermal error screens, in an attempt to help isolate which of the two (nozzle or bed) thermistors has triggered the shutdown. (NOTE: Some errors result in a display of 0 degrees on both, which unfortunately limits the usefulness of this feature.)
• The Leveling Settings screen is now also accessible from the Setup menu.
• The colour scheme has been modified from the original black/grey/red scheme, to add one thin red line under the grey screen header on each screen. (Solves issue #94, while still meeting the objective of visually distinguishing the refactored version from the original, to support troubleshooting.)
• Units have been added to the nozzle and bed temperature fields in a couple of screens.
• Updated the sample screenshots and clarified/updated the readme files.
• Modified the HZK font file (and rescaled a few fields to compensate for the font change), to stop DWIN_SET from clipping the descenders. (Solves Issue #31)

DEPRECATED IN THE RE-FACTORED RELEASE:

The ABL Mesh screen in this refactored firmware no longer includes the animated background icons, which used to turn each square from white to black, as the nozzle probed each point. (The method used to create that animation was not supported by the new tool.) CR6-MAX users will also notice that the small squares which represented the intermediate probing points are no longer displayed, as those were implemented with that same deprecated feature.

UPDATE - 16 March 2023 - Feedback on Release 1.1 documentation highlighted some errors and points of confusion, which have been rectified in Re-Factored DWIN_SET Version1.1.1.zip. I have chosen not to issue a new release for this, to avoid confusing folks any further about which files to use, as we communicate that version 1.1 is the 'latest". There are NO changes to the actual firmware at 1.1.1, it is purely a documentation fix... - Thinkersbluff.

UPDATE - 19 March 2023 - Ironically, when I generated refactored version 1.1, the DGUSTool I used did NOT create a version that would run on DGUS2 v4.5... My sincere apologies to those who got a blank screen.
My bad for not testing more rigorously. I have now reconfigured my test screen to run on DGUS2 v4.5, and have reworked my development environment to go back to the correct DGUSTool.

PLEASE DOWNLOAD Re-Factored.DWIN_SET.Version1.1.2.zip.

Re-Factored CR6 Community Touchscreen Firmware - STABLE RELEASE: 61F_220622_v1

This DWIN_SET is designated: 61F_220622_v1.

This video playlist provides a high-level tour of this refactored UI: https://youtube.com/playlist?list=PLfDSKnF0RNcbOUwW6B4rZagRsRP6l_rQg

PLEASE READ THE README FILE BEFORE FLASHING THIS FIRMWARE TO YOUR PRINTER.

Flashing the DWIN_SET in this release installs a TouchScreen firmware that works with the CF6.1-Final motherboard firmware and runs on any version of DGUS2 (Kerning problems may appear in some early versions.)

If you already have the CR6Community Firmware running on DGUS2 v3.5 on your printer, then you do not need to flash this firmware.

If you have DGUS2 v 4.4 or less flashed to your display, but not v3.5, then you MUST flash the kernel upgrade files to your display to install v3.5, if you wish to use the original CF6.1 Touchscreen firmware OR you can install this refactored DWIN_SET to your display.

If you have DGUS2 v4.5 or higher flashed to your display, you must flash this DWIN_SET instead of the one bundled with the motherboard firmware.

If you do flash this refactored firmware, you will benefit from the new features, but CR6-MAX users will lose one cosmetic feature:

NEW AT THIS RELEASE:

1. The last captured thermistor temperature values have been added to the three thermal error screens, in an attempt to help isolate which of the two (nozzle or bed) thermistors has triggered the shutdown. (NOTE: Some errors result in a display of 0 degrees on both, which unfortunately limits the usefulness of this feature.)
2. The Leveling Settings screen is now also accessible from the Setup menu.
3. The colour scheme has been modified from the original black/grey/red scheme to a "Cyanotype" theme.
4. Units have been added to a few fields.
5. Small bugs found while testing this version were also corrected. (This time, for sure?)
6. Added some more sample screenshots and clarified/updated the readme files.
7. Added the screen bitmap files to the DWIN_SET folder - for reference and mark-up with issues only. The bitmaps will not interfere with flashing but can be safely deleted from there, if you prefer.

DEPRECATED AT THIS RELEASE:

1. The ABL Mesh screen in this refactored firmware no longer includes the animated background icons, which used to turn each square from white to black, as the nozzle probed each point. (The method used to create that animation was not supported by the new tool.) CR6-MAX users will also notice that the small squares which represented the intermediate probing points are no longer displayed, as those were implemented with that same deprecated feature.

Re-Factored CR6 Community Touchscreen Firmware - Release Candidate 61F_RC_260522_v1

PLEASE READ THE README FILE BEFORE FLASHING THIS FIRMWARE TO YOUR PRINTER.

Flashing the DWIN_SET in this release installs a TouchScreen that works with the CF6.1-Final motherboard firmware and runs on any version of DGUS2 (v2.0 or higher.)

If you have DGUS2 v4.5 flashed to your display, you should flash this DWIN_SET instead of the one bundled with the motherboard firmware.
If you already have the CR6Community Firmware running on DGUS2 v3.5 on your printer, then you do not need to flash this firmware.

NOTE: The Load screen and the Setup->Info page will confirm the release number you have flashed, which should match the release number in the filename and in the README.txt file.

NEW AT THIS RELEASE:
User feedback in issue #83 lead to the discovery that two Toggle buttons were not displaying, due to a configuration error in the DGUS project file. That issue is now resolved.
Added a new button to the Setup Control Screen, to also be able to access the Leveling Settings Screen from the Setup Control Screen.

Other miscellaneous edits made at this release are:

Nudged the buttons on the Setup Control Screen, to make room for the new button
Deleted a temporary jpg file not intended to be part of the release.

We have designated this DWIN_SET as 61F_RC_260522_v1.

Re-Factored CR6 Community Touchscreen Firmware - Release Candidate 61F_RC_090522_v2

PLEASE READ THE README FILE BEFORE FLASHING THIS FIRMWARE TO YOUR PRINTER.

Flashing the DWIN_SET in this release installs a TouchScreen that works with the CF6.1-Final motherboard firmware and runs on any version of DGUS2 (v2.0 or higher.)

If you have DGUS2 v4.5 flashed to your display, you should flash this DWIN_SET instead of the one bundled with the motherboard firmware.
If you already have the CR6Community Firmware running on DGUS2 v3.5 on your printer, then you do not need to flash this firmware.

NOTE: The Load screen and the Setup->Info page will confirm the release number you have flashed, which should match the release number in the filename and in the README.MD file.

NEW AT THIS RELEASE:
There are three Thermal Error screens in the current design.
If any one of those conditions is triggered, it may not be clear whether the problem is with the Nozzle or the Bed.
Hoping to provide important troubleshooting clues, we have added Nozzle and Bed Sensor and Target readouts to all three of these thermal error screens:

1. Thermistor Error
2. Thermal Runaway
3. Heating Failed

While making these edits, we were also made aware (by InsanityAutomation) of a problem with the Z-Offset buttons implemented on the Printing Tune menu, which caused problems when held down rather than being tapped. We have implemented the fix that he recommended, in this release.

Other miscellaneous edits made at this release are:

• Nudged the temperature value displays to a common and suitable spacing on all screens.
• Replaced the two-part zip files of the new DGUSTool with a single consolidated file.
• Added a folder of Sample Screen Images, to help guide and inform users of this firmware
• Stopped using the build.ps1 script to build the DWIN_SET. Noticed that it renames files 13 and 14 from what names the new tool is giving them. Speculating (but have not yet confirmed by testing) that the white noise screen at the end of flashing to DGUS2 v4.5 screens may be a condition aggravated by those filenames having been changed.

We have designated this DWIN_SET as 61F_RC_090522_v2.

Re-Factored CR6 Community Touchscreen Firmware - Release Candidate 61F_RC_290422_v1

PLEASE READ THE README FILE BEFORE FLASHING THIS FIRMWARE TO YOUR PRINTER.

Flashing the DWIN_SET in this release installs a TouchScreen that works with the CF6.1-Final motherboard firmware and runs on any version of DGUS2 (v2.0 or higher.)

If you have DGUS2 v4.5 flashed to your display, you should flash this DWIN_SET instead of the one bundled with the motherboard firmware.

NOTE: The Load screen and the Setup->Info page will confirm the release number you have flashed, which should match the release number in the filename and in the README.MD file.

Community Firmware release 6.1

Please read the full announcement at the sister repository. Do not download the files below.

Troubleshooting

The Troubleshooting-experimental-DWIN_SET_format_kit.zip file below can be used to completely erase the touch screen.

This is experimental. Flashing may take multiple minutes. Do not abort flashing.

Make sure you follow the general flashing instructions, including removing all files from your SD card.

Community Firmware "Tune it, love it" release 6

Please read the full announcement at the sister repository. Do not download the files below.

Troubleshooting

The Troubleshooting-experimental-DWIN_SET_format_kit.zip file below can be used to completely erase the touch screen.

This is experimental. Flashing may take multiple minutes. Do not abort flashing.

Make sure you follow the general flashing instructions, including removing all files from your SD card.

CR-6 Community Firmware release 5 beta "Happy new year" edition

Please read the full announcement at the sister repository. Do not download the files below.

Community firmware release 4 alpha based on Marlin v2.0.7.1 - rewritten from scratch

Please refer to the Marlin fork release page.

v1.0.0-a1

• Update display icons
• Drop Chinese support #1
• Update font and graphics