[Keyboard] wilba.tech PCB refactoring (qmk#6982)

* Cleanup * Refactor VIA rules.mk * WT mono backlight refactor, VIA support * Added WT75-C * Fixed compile error * Cleanup rules.mk * Review changes * Review changes
HokieGeek · Feb 21, 2020 · fad3fe5 · fad3fe5
1 parent bbec6a5
commit fad3fe5
Show file tree

Hide file tree

Showing 48 changed files with 1,132 additions and 1,250 deletions.
diff --git a/keyboards/aeboards/aegis/config.h b/keyboards/aeboards/aegis/config.h
@@ -47,8 +47,6 @@
 /* Locking resynchronize hack */
 #define LOCKING_RESYNC_ENABLE
 
-//#define WT_MONO_BACKLIGHT
-
 #define DYNAMIC_KEYMAP_LAYER_COUNT 4
 
 // EEPROM usage

diff --git a/keyboards/aeboards/ext65/config.h b/keyboards/aeboards/ext65/config.h
@@ -47,8 +47,6 @@
 /* Locking resynchronize hack */
 #define LOCKING_RESYNC_ENABLE
 
-//#define WT_MONO_BACKLIGHT
-
 #define DYNAMIC_KEYMAP_LAYER_COUNT 4
 
 // EEPROM usage

diff --git a/keyboards/snagpad/config.h b/keyboards/snagpad/config.h
@@ -48,9 +48,6 @@
 #define RGBLIGHT_VAL_STEP 8
 #endif
 
-// Does not use WT_MONO_BACKLIGHT
-// #define WT_MONO_BACKLIGHT
-
 #define DYNAMIC_KEYMAP_LAYER_COUNT 4
 
 // EEPROM usage

diff --git a/keyboards/wilba_tech/rama_works_koyu/rules.mk b/keyboards/wilba_tech/rama_works_koyu/rules.mk
@@ -1,5 +1,3 @@
-
-
 # project specific files
 SRC =	keyboards/wilba_tech/wt_main.c \
 		keyboards/wilba_tech/wt_rgb_backlight.c \
@@ -10,42 +8,14 @@ SRC =	keyboards/wilba_tech/wt_main.c \
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-# Boot Section
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
 # Do not put the microcontroller into power saving mode

diff --git a/keyboards/wilba_tech/rama_works_m10_b/config.h b/keyboards/wilba_tech/rama_works_m10_b/config.h
@@ -181,8 +181,6 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 /* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
 //#define MIDI_TONE_KEYCODE_OCTAVES 1
 
-//#define WT_MONO_BACKLIGHT
-
 #define DYNAMIC_KEYMAP_LAYER_COUNT 4
 
 // EEPROM usage

diff --git a/keyboards/wilba_tech/rama_works_m10_b/rules.mk b/keyboards/wilba_tech/rama_works_m10_b/rules.mk
@@ -4,44 +4,14 @@ SRC =	keyboards/wilba_tech/wt_main.c
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
 

diff --git a/keyboards/wilba_tech/rama_works_m60_a/rules.mk b/keyboards/wilba_tech/rama_works_m60_a/rules.mk
@@ -10,42 +10,14 @@ SRC =	keyboards/wilba_tech/wt_main.c \
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-# Boot Section
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
 # Do not put the microcontroller into power saving mode

diff --git a/keyboards/wilba_tech/rama_works_m6_a/rules.mk b/keyboards/wilba_tech/rama_works_m6_a/rules.mk
@@ -4,43 +4,14 @@ SRC =	keyboards/wilba_tech/wt_main.c
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-# Boot Section
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
 # Do not put the microcontroller into power saving mode

diff --git a/keyboards/wilba_tech/rama_works_m6_b/rules.mk b/keyboards/wilba_tech/rama_works_m6_b/rules.mk
@@ -5,47 +5,17 @@ SRC =	keyboards/wilba_tech/wt_main.c \
 		drivers/issi/is31fl3218.c \
 		drivers/avr/i2c_master.c
 
-
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-# Boot Section
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
 # Do not put the microcontroller into power saving mode

diff --git a/keyboards/wilba_tech/rama_works_u80_a/config.h b/keyboards/wilba_tech/rama_works_u80_a/config.h
@@ -179,8 +179,6 @@
 /* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
 //#define MIDI_TONE_KEYCODE_OCTAVES 1
 
-//#define WT_MONO_BACKLIGHT
-
 // IS31FL3731 driver
 #define DRIVER_COUNT 3
 #define DRIVER_LED_TOTAL 108

diff --git a/keyboards/wilba_tech/rama_works_u80_a/rules.mk b/keyboards/wilba_tech/rama_works_u80_a/rules.mk
@@ -8,44 +8,14 @@ SRC =	keyboards/wilba_tech/wt_main.c \
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu