The SIDPod is a PSID player for RP2040 microcontroller based boards, such as the Raspberry Pi Pico or the Solder Party RP2040 Stamp. Playback is based on the SID emulator found in Rockbox, which in turn is based on TinySID.
Current status of SIDPod-SDCard is work in progress. Development is being done in VSCode with WSL2. OpenOCD runs on linux box and gdb connects from WSL2.
In the photo below are two sidpods, one original and one sdcard.
SIDPod requires both the Raspberry Pi Pico SDK and the
pico-extras. Make sure to grab these and either put them next to the
SIDPod directory or, if you have them somewhere else, point the PICO_SDK_PATH and PICO_EXTRAS_PATH environment
variables to their respective location. You'll also need CMake on your path. If/when these prerequisites have been
satisfied, you're almost ready to run the cmake command to create the build directory and configure the build. One
last thing to do is to make sure the board type matches the one you have. By default, SIDPod builds for the Solder Party
RP2040 Stamp, which, for example, has a larger NAND flash than the more common Raspberry Pi Pico. Using a RP2040 Stamp
UF2 on a Pi Pico would most likely cause issues on the first run, as the flash will get formatted, using board
specific settings, if no readable FAT filesystem is found on it. Changing board type can either be done by modifying
the PICO_BOARD variable in CMakeLists.txt or by setting the PICO_BOARD environment variable before
running the cmake commands. The correct value for the Raspberry Pi Pico is 'pico'. Once this is done, the build is
configured by running:
cmake -B cmake-build-debug
Alternatively, if you have Ninja installed, you can save a few seconds of your valuable time by instead running:
cmake -G Ninja -B cmake-build-debug
Then, to build the SIDPod.uf2 binary, issue:
cmake --build cmake-build-debug --target all -j 12
Once the build finishes, just follow the official instructions for loading a UF2 binary onto the board. For Raspberry Pi Pico you hold down the BOOTSEL button when you plug it in and then copy SIDPod.uf2 to it, once it appears as a drive named RPI-RP2. For some other types of boards, such as the Solder Party RP2040 Stamp, this mode is activated by double-clicking the reset button.
Also note that if you're running macOS, copying using Finder might fail with this error: The operation can’t be completed because an unexpected error occurred (error code 100093). If this is the case, fire up the 'ol terminal and do:
cp cmake-build-debug/SIDPod.uf2 /Volumes/RPI-RP2
To get a jump start you can also grab the prebuilt binaries. There are two versions, one for the Solder Party RP2040 Stamp and one for the Raspberry Pi Pico.
Since the main goal is to make a portable player, the actual build and design is up to you, the maker. My current prototype is built inside a 3-AA battery box I had lying around, using a Solder Party RP2040 Stamp and a 3.7V 150mAh LiPo battery. However, the breadboard design I'm using for development, based on a Raspberry Pi Pico H, looks like this:
The breadboard schematics.
In reality, the development breadboard looks a bit different. I use a dual lane breadboard and connect to the SIDPod Pico board via a Picoprobe, for debugging and a less painful development process.
The development breadboard setup.
The working prototype. Please excuse the soldering. I'm a lover, not a solderer. 😜
The main advantage of the Solder Party RP2040 Stamp, besides its size, is the onboard LiPo charger. This removes some complexity and saves space when moving beyond the breadboard design. Many RP2040 projects can easily run off the power provided from the host computer over the built-in USB port. The SIDPod however, will enter a special USB device state and start to mimic a USB mass storage device once connected to a computer. More on that here. This poses a problem, if you actually want to use it for what it's designed for - to play PSIDs. That problem can easily be solved by powering it from any power source connected to the VSYS pin. That power source can be anything from a 3.7V LiPo battery to a separate USB breakout bord, with the breakout boards VBUS connected to VSYS on the Pico Board and the breakout board GND connector connected to any GND on the Pico Board. In my development breadboard setup I power the SIDPod Pico Board from the Picoprobe Pico Board. In the next section I've listed the components needed for a few different options:
Option 1 - Using a Solder Party RP2040 Stamp (the prototype setup):
- 1 x Solder Party RP2040 Stamp
- 1 x Adafruit I2S 3W Class D Amp - MAX98357A
- 1 x LCD OLED 0.91″ 128x32px I2C
- 1 x 3.5mm stereo jack
- 1 x Rotary encoder w switch
- 2 x 100Ω resistor
- 1 x Battery LiPo 3.7V 150mAh
Option 2 - Using a Raspberry Pi Pico (the breadboard setup):
- 1 x Adafruit I2S 3W Class D Amp - MAX98357A
- 1 x LCD OLED 0.91″ 128x32px I2C
- 1 x 3.5mm stereo jack
- 1 x Rotary encoder w switch
- 2 x 100Ω resistor
Option 2a - Add a Raspberry Pi Pico with Picoprobe, for debugging, binary upload and power through VSYS:
Option 2b - Power the Raspberry Pi Pico through a USB breakout board:
To keep the construction as simple as possible I tried to minimize the number of physical controls, and a rotary encoder with a built-in push button provides enough versatility to cater to every possible use case of this rather minimal design. Therefore, controls are both contextual and pattern driven.
The SID or Sound Interface Device, which this player does a rudimentary emulation of, was a component in the world's most popular home computer, the Commodore 64. Due to its legendary status and, to this day, very active community, there's no shortage of SID files to fill your SIDPod with. The most complete collection is the High Voltage SID Collection. It has everything, from cult classics by the legendary Jeroen Tel to contemporary pieces by Kamil Wolnikowski, aka Jammer. Download the full archive and use one of the SID players referenced on that page to find the music you like. The collection contains both PSIDs and RSIDs. However, RSID playback requires either a real C64 or a more sophisticated emulator than TinySID. More on the effects of this in the next section.
The SIDPod doubles as a USB mass storage device, which means that if you plug it in to your computer it will show up as a regular, FAT-formatted drive. This means that adding and removing PSIDs is as easy as copying or deleting files. There are a few caveats though:
- Only PSIDs are supported, RSIDs are filtered out. Unfortunately they share the same file extension, which means it's impossible to know beforehand if a SID file is playable or not. So, if you add a tune to the SIDPod, and it doesn't show up, this is most likely the cause.
- PSIDs must be put in the root directory.
- Use it with moderation. FatFs doesn't have any wear levelling algorithm, and NAND flash storage wears out faster than regular flash drives. Note though that this only goes for write operations. Reading is totally harmless.
- It's slower than you're probably used to. This is due to several factors. One being that flash memory blocks needs to be erased before new data can be written to them.
While the SIDPod is connected, the screen shows flickering bars. Don't be alarmed. This is a feature, not a bug. In fact, it's a reference to the C64 - those who know, know.
Once you've added some funky tunes and safely disconnected the SIDPod it presents the titles. In the order they were added. The controls in this mode are:
- Scroll through the list by turning the encoder.
- Single-clicking plays the selected song and enters a very retro-fancy visualization mode.
- Double-clicking plays or pauses the selected song but keeps the playlist mode.
- Double-clicking in visualization mode pauses playback and displays a pause notification on screen.
The currently selected song is decorated with a traditional play symbol and the currently playing song is decorated with an animated spectrum analyser symbol. When a song is paused, the animation is paused as well.
If a song gets crossed out when you're trying to play it, it means that it's either corrupt or uses a combination of opcodes that have caused the song loading routine to enter an infinite loop and seemingly hang. This is very rare.
These controls are only available from the visualization mode and are activated by rotating the encoder. The controls in this mode are:
- Lower/raise the volume by turning the encoder.
- Single-clicking toggles line level on/off. Use this if you notice distortion when the SIDPod is connected to an amplifier.
After two seconds of inactivity the SIDPod returns to the visualization mode.
In this mode the screen is turned off, as well as the regular controls. Playback is still active though, which makes it perfect for when you're out and about. To enter this mode, simply hold the button pressed until the screen goes black. This takes exactly one second. Be careful not to hold it for too long, as this will put the SIDPod to sleep. More on that in the next section. To get out of pocket mode, simply double-click, and it will return to whatever mode you were in before entering pocket mode.
This mode is as close as you can get to turning the SIDPod off. As with pocket mode, all regular controls are disabled. Additionally, playback is stopped, as well as USB device clocks. In fact, in this mode, even both processor cores are stopped, meaning that the power consumption is next to nothing. To enter deep sleep, press the button for more than two and a half second. To get out, just double-click.