New board: AIRLink board configuration added

.ci/Jenkinsfile-compile

@@ -104,6 +104,7 @@ pipeline {
                      "px4_fmu-v6u_default",
                      "px4_fmu-v6x_default",
                      "px4_io-v2_default",
+                     "sky-drones_smartap-airlink_default",
                      "spracing_h7extreme_default",
                      "uvify_core_default"
             ],

boards/sky-drones/smartap-airlink/default.px4board

@@ -0,0 +1,109 @@
+CONFIG_BOARD_TOOLCHAIN="arm-none-eabi"
+CONFIG_BOARD_ARCHITECTURE="cortex-m7"
+CONFIG_BOARD_ETHERNET=y
+CONFIG_BOARD_SERIAL_GPS1="/dev/ttyS0"
+CONFIG_BOARD_SERIAL_GPS2="/dev/ttyS7"
+CONFIG_BOARD_SERIAL_TEL1="/dev/ttyS6"
+CONFIG_BOARD_SERIAL_TEL2="/dev/ttyS4"
+CONFIG_BOARD_SERIAL_TEL3="/dev/ttyS1"
+CONFIG_BOARD_SERIAL_PPB="/dev/ttyS3"
+CONFIG_DRIVERS_ADC_BOARD_ADC=y
+CONFIG_COMMON_BAROMETERS=y
+CONFIG_DRIVERS_BATT_SMBUS=y
+CONFIG_DRIVERS_CAMERA_CAPTURE=y
+CONFIG_DRIVERS_CAMERA_TRIGGER=y
+CONFIG_COMMON_DIFFERENTIAL_PRESSURE=y
+CONFIG_COMMON_DISTANCE_SENSOR=y
+CONFIG_DRIVERS_DSHOT=y
+CONFIG_DRIVERS_GPS=y
+CONFIG_DRIVERS_HEATER=y
+CONFIG_DRIVERS_IMU_BOSCH_BMI088=y
+CONFIG_DRIVERS_IMU_INVENSENSE_ICM20602=y
+CONFIG_DRIVERS_IMU_INVENSENSE_MPU9250=y
+CONFIG_DRIVERS_IRLOCK=y
+CONFIG_COMMON_LIGHT=y
+CONFIG_COMMON_MAGNETOMETER=y
+CONFIG_COMMON_OPTICAL_FLOW=y
+CONFIG_DRIVERS_OSD=y
+CONFIG_DRIVERS_PCA9685=y
+CONFIG_DRIVERS_PCA9685_PWM_OUT=y
+CONFIG_DRIVERS_PWM_INPUT=y
+CONFIG_DRIVERS_PWM_OUT=y
+CONFIG_DRIVERS_PWM_OUT_SIM=y
+CONFIG_DRIVERS_PX4IO=y
+CONFIG_DRIVERS_RC_INPUT=y
+CONFIG_DRIVERS_ROBOCLAW=y
+CONFIG_DRIVERS_RPM=y
+CONFIG_DRIVERS_SAFETY_BUTTON=y
+CONFIG_DRIVERS_SMART_BATTERY_BATMON=y
+CONFIG_COMMON_TELEMETRY=y
+CONFIG_DRIVERS_TONE_ALARM=y
+CONFIG_DRIVERS_UAVCAN=y
+CONFIG_MODULES_AIRSPEED_SELECTOR=y
+CONFIG_MODULES_ATTITUDE_ESTIMATOR_Q=y
+CONFIG_MODULES_BATTERY_STATUS=y
+CONFIG_MODULES_CAMERA_FEEDBACK=y
+CONFIG_MODULES_COMMANDER=y
+CONFIG_MODULES_CONTROL_ALLOCATOR=y
+CONFIG_MODULES_DATAMAN=y
+CONFIG_MODULES_EKF2=y
+CONFIG_MODULES_ESC_BATTERY=y
+CONFIG_MODULES_EVENTS=y
+CONFIG_MODULES_FLIGHT_MODE_MANAGER=y
+CONFIG_MODULES_FW_ATT_CONTROL=y
+CONFIG_MODULES_FW_AUTOTUNE_ATTITUDE_CONTROL=y
+CONFIG_MODULES_FW_POS_CONTROL_L1=y
+CONFIG_MODULES_GIMBAL=y
+CONFIG_MODULES_GYRO_CALIBRATION=y
+CONFIG_MODULES_GYRO_FFT=y
+CONFIG_MODULES_LAND_DETECTOR=y
+CONFIG_MODULES_LANDING_TARGET_ESTIMATOR=y
+CONFIG_MODULES_LOAD_MON=y
+CONFIG_MODULES_LOCAL_POSITION_ESTIMATOR=y
+CONFIG_MODULES_LOGGER=y
+CONFIG_MODULES_MAG_BIAS_ESTIMATOR=y
+CONFIG_MODULES_MANUAL_CONTROL=y
+CONFIG_MODULES_MAVLINK=y
+CONFIG_MODULES_MC_ATT_CONTROL=y
+CONFIG_MODULES_MC_AUTOTUNE_ATTITUDE_CONTROL=y
+CONFIG_MODULES_MC_HOVER_THRUST_ESTIMATOR=y
+CONFIG_MODULES_MC_POS_CONTROL=y
+CONFIG_MODULES_MC_RATE_CONTROL=y
+CONFIG_MODULES_NAVIGATOR=y
+CONFIG_MODULES_RC_UPDATE=y
+CONFIG_MODULES_ROVER_POS_CONTROL=y
+CONFIG_MODULES_SENSORS=y
+CONFIG_MODULES_SIH=y
+CONFIG_MODULES_TEMPERATURE_COMPENSATION=y
+CONFIG_MODULES_VTOL_ATT_CONTROL=y
+CONFIG_SYSTEMCMDS_ACTUATOR_TEST=y
+CONFIG_SYSTEMCMDS_BL_UPDATE=y
+CONFIG_SYSTEMCMDS_DMESG=y
+CONFIG_SYSTEMCMDS_DUMPFILE=y
+CONFIG_SYSTEMCMDS_GPIO=y
+CONFIG_SYSTEMCMDS_HARDFAULT_LOG=y
+CONFIG_SYSTEMCMDS_I2CDETECT=y
+CONFIG_SYSTEMCMDS_LED_CONTROL=y
+CONFIG_SYSTEMCMDS_MFT=y
+CONFIG_SYSTEMCMDS_MIXER=y
+CONFIG_SYSTEMCMDS_MOTOR_TEST=y
+CONFIG_SYSTEMCMDS_MTD=y
+CONFIG_SYSTEMCMDS_NETMAN=y
+CONFIG_SYSTEMCMDS_NSHTERM=y
+CONFIG_SYSTEMCMDS_PARAM=y
+CONFIG_SYSTEMCMDS_PERF=y
+CONFIG_SYSTEMCMDS_PWM=y
+CONFIG_SYSTEMCMDS_REBOOT=y
+CONFIG_SYSTEMCMDS_REFLECT=y
+CONFIG_SYSTEMCMDS_SD_BENCH=y
+CONFIG_SYSTEMCMDS_SD_STRESS=y
+CONFIG_SYSTEMCMDS_SERIAL_TEST=y
+CONFIG_SYSTEMCMDS_SYSTEM_TIME=y
+CONFIG_SYSTEMCMDS_TOP=y
+CONFIG_SYSTEMCMDS_TOPIC_LISTENER=y
+CONFIG_SYSTEMCMDS_TUNE_CONTROL=y
+CONFIG_SYSTEMCMDS_UORB=y
+CONFIG_SYSTEMCMDS_USB_CONNECTED=y
+CONFIG_SYSTEMCMDS_VER=y
+CONFIG_SYSTEMCMDS_WORK_QUEUE=y
+CONFIG_EXAMPLES_FAKE_GPS=y

boards/sky-drones/smartap-airlink/firmware.prototype

@@ -0,0 +1,13 @@
+{
+    "board_id": 55,
+    "magic": "PX4FWv1",
+    "description": "Firmware for the SMARTAP AIRLINK board",
+    "image": "",
+    "build_time": 0,
+    "summary": "SMARTAP-AIRLINK",
+    "version": "0.1",
+    "image_size": 0,
+    "image_maxsize": 2064384,
+    "git_identity": "",
+    "board_revision": 0
+}

boards/sky-drones/smartap-airlink/init/rc.board_defaults

@@ -0,0 +1,29 @@
+#!/bin/sh
+#
+# board specific defaults
+#------------------------------------------------------------------------------
+
+# Telemetry for onboard computer
+param set-default MAV_1_CONFIG 102 	# TELEM2
+param set-default MAV_1_MODE 0 			# Normal
+param set-default SER_TEL2_BAUD 921600  	# 921600
+
+# Temperature stabilization
+param set-default SENS_EN_THERMAL 1 		# Enable heater
+param set-default SENS_TEMP_ID 2359314 		# Heated IMU ID
+
+# Battery scaling
+param set-default BAT_N_CELLS 4
+param set-default BAT1_N_CELLS 4
+
+param set-default BAT1_V_DIV 15.51
+
+param set-default BAT1_A_PER_V 36.00
+
+param set-default BAT_V_OFFS_CURR 0.413
+
+# Disable safety switch
+param set-default CBRK_IO_SAFETY 22027
+
+
+safety_button start

boards/sky-drones/smartap-airlink/init/rc.board_mavlink

@@ -0,0 +1,7 @@
+#!/bin/sh
+#
+# board specific MAVLink startup script.
+#------------------------------------------------------------------------------
+
+# Start MAVLink on the USB port
+mavlink start -d /dev/ttyACM0

boards/sky-drones/smartap-airlink/init/rc.board_sensors

@@ -0,0 +1,34 @@
+#!/bin/sh
+#
+# SMARTAP AIRLINK specific board sensors init
+#------------------------------------------------------------------------------
+board_adc start
+
+# Internal SPI bus MPU-9250 / SPI 2 [FPC]
+mpu9250 -s -b 2 -M -R 6 start
+
+# Internal SPI bus ICM-20602 / SPI 1
+icm20602 -R 0 -s start
+
+# Internal SPI bus MPU-9250 / SPI 3
+mpu9250 -s -b 3 -M -R 4 start
+
+# Internal compass
+bmm150 -I start
+
+# Internal Baro
+ms5611 -X start
+
+# Internal Baro
+bmp388 -I -a 0x77 start
+#bmp388 -I start
+
+# External HMC5983
+hmc5883 -T -X -R 4 start
+
+# External LIS3MDL
+lis3mdl -R 2 -X start
+
+# NCP5623 Led driver
+rgbled_ncp5623c -X -a 0x38 start
+

boards/sky-drones/smartap-airlink/nuttx-config/Kconfig

@@ -0,0 +1,17 @@
+#
+# For a description of the syntax of this configuration file,
+# see misc/tools/kconfig-language.txt.
+#
+config BOARD_HAS_PROBES
+	bool "Board provides GPIO or other Hardware for signaling to timing analyze."
+	default y
+	---help---
+		This board provides GPIO FMU-CH1-8, CAP1 as PROBE_1-9 to provide timing signals from selected drivers.
+
+config BOARD_USE_PROBES
+	bool "Enable the use the board provided FMU-CH1-8, CAP1 as PROBE_1-9"
+	default n
+	depends on BOARD_HAS_PROBES
+
+	---help---
+		Select to use GPIO FMU-CH1-8, CAP1  to provide timing signals from selected drivers.