RAUC controls the update process on embedded Linux systems. It is both a target application that runs as an update client and a host/target tool that allows you to create, inspect and modify installation artifacts.
Source Code: https://github.com/rauc/rauc
Documentation: https://rauc.readthedocs.org/
Chat: IRC channel #rauc
on freenode (bridged to the
Matrix channel #rauc:matrix.org)
- Fail-Safe & Atomic:
- An update may be interrupted at any point without breaking the running system.
- Update compatibility check
- Cryptographic signing and verification of updates using OpenSSL (signatures
based on x.509 certificates)
- Keys and certificates on PKCS#11 tokens (HSMs) are supported
- Flexible and customizable redundancy/storage setup
- Symmetric setup (Root-FS A & B)
- Asymmetric setup (recovery & normal)
- Application partition, Data Partitions, ...
- Allows grouping of multiple slots (rootfs, appfs) as update targets
- Network streaming mode using casync
- chunk-based binary delta updates
- significantly reduce download size
- no extra storage required
- Bootloader support:
- Storage support:
- ext2/3/4 filesystem
- eMMC boot partitions (atomic update)
- vfat filesystem
- UBI volumes
- UBIFS
- raw NAND (using nandwrite)
- squashfs
- MBR partition table
- Independent from updates source
- USB Stick
- Software provisioning server (e.g. Hawkbit)
- Controllable via D-Bus interface
- Supports Data migration
- Network protocol support using libcurl (https, http, ftp, ssh, ...)
- Several layers of update customization
- Update-specific extensions (hooks)
- System-specific extensions (handlers)
- fully custom update script
- Create update bundles
- Sign/resign bundles
- Inspect bundle files
- Run as a system service (d-bus interface)
- Install bundles
- View system status information
- Change status of symmetric/asymmetric/custom slots
- Boot state storage
- GRUB: environment file on SD/eMMC/SSD/disk
- Barebox: State partition on EEPROM/FRAM/MRAM or NAND flash
- U-Boot: environment variable
- EFI: EFI variables
- Boot target selection support in the bootloader
- Enough mass storage for two symmetric/asymmetric/custom slots
- For normal bundle mode:
- Enough storage for the compressed bundle file (in memory, in a temporary partition or on an external storage device)
- For casync bundle mode:
- No additional storage needed
- Network interface
- Hardware watchdog (optional, but recommended)
- RTC (optional, but recommended)
Please see the documentation for details.
- automake
- libtool
- libdbus-1-dev
- libglib2.0-dev
- libcurl3-dev
- libssl-dev
sudo apt-get install automake libtool libdbus-1-dev libglib2.0-dev libcurl3-dev libssl-dev
If you intend to use json-support you also need
sudo apt-get install libjson-glib-dev
Required kernel options:
CONFIG_BLK_DEV_LOOP=y
CONFIG_SQUASHFS=y
For using tar archive in RAUC bundles with Busybox tar, you have to enable the following Busybox feature:
CONFIG_FEATURE_TAR_AUTODETECT=y
CONFIG_FEATURE_TAR_LONG_OPTIONS=y
Depending on the actual storage type and/or filesystem used, further target tools might be required. The documentation chapter Required Target Tools gives a more detailed list on these.
Note
RAUC is intended to be built both as a host tool as well as a target tool (service). Therefore it is fully prepared for automake cross-compilation
git clone https://github.com/rauc/rauc cd rauc ./autogen.sh ./configure make
Note
To prepare RAUC for the target device, it is highly recommended to use an embedded Linux distribution build suite such as Yocto/OE, PTXdist or Buildroot.
On the host system RAUC can be used directly from the build dir, or optionally be installed. On the target instead, installing is highly recommended as it also unpacks service and D-Bus configuration files required to run RAUC properly:
make install
sudo apt-get install user-mode-linux slirp squashfs-tools # Optional to run all tests: # sudo apt-get install faketime casync grub-common softhsm2 opensc opensc-pkcs11 libengine-pkcs11-openssl make check ./uml-test
Create a directory with the content that should be installed:
mkdir content-dir/ cp $SOURCE/rootfs.ext4 content-dir/
Create a manifest describing which image to install where together with some meta info:
cat >> content-dir/manifest.raucm << EOF [update] compatible=FooCorp Super BarBazzer version=2019.01-1 [image.rootfs] filename=rootfs.ext4 EOF
Let RAUC create a bundle from this:
rauc --cert autobuilder.cert.pem --key autobuilder.key.pem bundle content-dir/ update-2019.01-1.raucb
Create a system configuration file in /etc/rauc/system.conf
and start the
service process in background:
rauc service &
To install the bundle on your target device, run:
rauc install update-2019.01-1.raucb
Fork the repository and send us a pull request.
Please read the Documentation's Contributing section for more details.