This is a C driver program for operating a Bosch BNO055 IMU sensor via I2C on a Raspberry Pi. I used it with a GY-BNO055 and a Adafruit BNO055. On the GY-BNO055, I had to bridge two solder pads for enabling I2C mode, because serial mode was default. Later I switched to Adafruit for the superior quality and the onboard 5V-level support.
For I2C communication functions, I am using the i2c-tools and i2c-dev packages.
sudo apt-get install -y i2c-tools libi2c-dev
Now we can use the i2cdetect command to query the I2C bus. Connecting the GY-BNO055 sensor to the Raspberry Pi I2C bus, the sensor responds with the slave address 0x29. The Adafruit sensor responds by default under 0x28.
root@pi-ws01:/home/pi# i2cdetect -y 1
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- 28 -- -- -- -- -- -- --
30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --
Compiling the test program:
root@pi-ws01:/home/pi/bno055# make
cc -O3 -Wall -g -c -o i2c_bno055.o i2c_bno055.c
cc -O3 -Wall -g -c -o getbno055.o getbno055.c
cc i2c_bno055.o getbno055.o -o getbno055
Running the program, extracting the sensor version and configuration information:
pi@nanopi-neo2:~/pi-bno055 $ ./getbno055 -t inf
BN0055 Information at Sun Nov 11 14:09:47 2018
----------------------------------------------
Chip Version ID = 0xA0
Accelerometer ID = 0xFB
Gyroscope ID = 0x0F
Magnetoscope ID = 0x32
Software Version = 3.17
Operations Mode = NDOF_FMC_OFF
Power Mode = NORMAL
Axis Configuration = X==X Y==Y Z==Z (ENU)
Axis Remap Sign = X+ Y+ Z+
System Status Code = Sensor running with fusion algorithm
Accelerometer Test = OK
Magnetometer Test = OK
Gyroscope Test = OK
MCU Cortex M0 Test = OK
System Error Code = No Error
Acceleration Unit = m/s2
Gyroscope Unit = dps
Euler Unit = Degrees
Temperature Unit = Celsius
Orientation Mode = Windows
Sensor Temperature = 29°C
----------------------------------------------
Accelerometer Power = NORMAL
Accelerometer Bwidth = 7.81Hz
Accelerometer GRange = 2G
Accelerometer Sleep = event-driven, 0.5ms
----------------------------------------------
Sensor System Calibration = Fully calibrated
Gyroscope Calibration = Fully calibrated
Accelerometer Calibration = Minimal Calibrated
Magnetometer Calibration = Fully calibrated
Running the program, showing the sensor calibration state and offset values:
pi@nanopi-neo2:~/pi-bno055 $ ./getbno055 -t cal
sys [S:3] acc [S:1 X:0 Y:65534 Z:65528 R:1000] mag [S:3 X:65428 Y:65424 Z:65476 R:656] gyr [S:3 X:65534 Y:0 Z:1]
Changing the operational mode, e.g. to CONFIG:
pi@pi-ws01:~/pi-bno055 $ ./getbno055 -v -m config
Debug: arg -s, value config
Debug: ts=[1539005771] date=Mon Oct 8 22:36:11 2018
Debug: Sensor Address: [0x28]
Debug: Write opr_mode: [0x00] to register [0x3D]
Resetting the sensor:
pi@pi-ws01:~/pi-bno055 $ ./getbno055 -v -r
Debug: arg -r, value (null)
Debug: ts=[1539005864] date=Mon Oct 8 22:37:44 2018
Debug: Sensor Address: [0x28]
Debug: BNO055 Sensor Reset complete
NDOF fusion mode, Euler angles
pi@nanopi-neo2:~/pi-bno055 $ ./getbno055 -t eul
EUL 233.00 -3.12 -15.94
Writing calibration data to file
pi@nanopi-neo2:~/pi-bno055 $ ./getbno055 -t cal -w bno.cfg
sys [S:3] acc [S:1 X:0 Y:65534 Z:65528 R:1000] mag [S:3 X:65428 Y:65424 Z:65476 R:656] gyr [S:3 X:65534 Y:65535 Z:1]
pi@nanopi-neo2:~/pi-bno055 $ ls -l bno.cfg
-rw-rw-r-- 1 pi pi 22 Nov 11 14:17 bno.cfg
pi@nanopi-neo2:~/pi-bno055 $ od -A x -t x1 -v bno.cfg
000000 00 00 fe ff f8 ff 94 ff 90 ff c4 ff fe ff ff ff
000010 01 00 e8 03 90 02
000016
Program usage:
pi@nanopi-neo2:~/pi-bno055 $ ./getbno055
Usage: getbno055 [-a hex i2c-addr] [-m <opr_mode>] [-t acc|gyr|mag|eul|qua|lin|g ra|inf|cal] [-r] [-w calfile] [-l calfile] [-o htmlfile] [-v]
Command line parameters have the following format:
-a sensor I2C bus address in hex, Example: -a 0x28 (default)
-b I2C bus to query, Example: -b /dev/i2c-1 (default)
-d dump the complete sensor register map content
-m set sensor operational mode. mode arguments:
config = configuration mode
acconly = accelerometer only
magonly = magnetometer only
gyronly = gyroscope only
accmag = accelerometer + magnetometer
accgyro = accelerometer + gyroscope
maggyro = magetometer + gyroscope
amg = accelerometer + magnetometer + gyroscope
imu = accelerometer + gyroscope fusion -> rel. orientation
compass = accelerometer + magnetometer fusion -> abs. orientation
m4g = accelerometer + magnetometer fusion -> rel. orientation
ndof = accelerometer + mag + gyro fusion -> abs. orientation
ndof_fmc = ndof, using fast magnetometer calibration (FMC)
-p set sensor power mode. mode arguments:
normal = required sensors and MCU always on (default)
low = enter sleep mode during motion inactivity
suspend = sensor paused, all parts put to sleep
-r reset sensor
-t read and output sensor data. data type arguments:
acc = Accelerometer (X-Y-Z axis values)
gyr = Gyroscope (X-Y-Z axis values)
mag = Magnetometer (X-Y-Z axis values)
eul = Orientation E (H-R-P values as Euler angles)
qua = Orientation Q (W-X-Y-Z values as Quaternation)
gra = GravityVector (X-Y-Z axis values)
lin = Linear Accel (X-Y-Z axis values)
inf = Sensor info (23 version and state values)
cal = Calibration data (mag, gyro and accel calibration values)
continuous = continuous data-eul
-l load sensor calibration data from file, Example -l ./bno055.cal
-w write sensor calibration data to file, Example -w ./bno055.cal
-o output sensor data to HTML table file, requires -t, Example: -o ./bno055.html
-h display this message
-v enable debug output
Note: The sensor is executing calibration in the background, but only in fusion mode.
Usage examples:
./getbno055 -a 0x28 -t inf -v
./getbno055 -t cal -v
./getbno055 -t eul -o ./bno055.html
./getbno055 -m ndof
./getbno055 -w ./bno055.cal
The sensor register data can be dumped out with the "-d" argument:
pi@nanopi-neo2:~/pi-bno055 $ ./getbno055 -d
------------------------------------------------------
BNO055 page-0:
------------------------------------------------------
reg 0 1 2 3 4 5 6 7 8 9 A B C D E F
------------------------------------------------------
[0x00] A0 FB 32 0F 11 03 15 00 71 FF B1 00 B5 03 44 FE
[0x10] FB 32 0F 11 03 15 00 71 FF B1 00 B5 03 44 FE BE
[0x20] 32 0F 11 03 15 00 71 FF B1 00 B5 03 44 FE BE 02
[0x30] 0F 11 03 15 00 71 FF B1 00 B5 03 44 FE BE 02 6A
[0x40] 11 03 15 00 6F FF B1 00 C2 03 44 FE BE 02 6A FD
[0x50] 03 15 00 6F FF B1 00 C2 03 44 FE BE 02 6A FD FE
[0x60] 15 00 6F FF B1 00 C2 03 44 FE BE 02 6A FD FE FF
[0x70] 00 6F FF B1 00 C2 03 44 FE BE 02 6A FD FF FF FF
------------------------------------------------------
BNO055 page-1:
------------------------------------------------------
reg 0 1 2 3 4 5 6 7 8 9 A B C D E F
------------------------------------------------------
[0x00] 00 03 05 00 0C 00 00 01 0D 6D 38 00 00 00 00 00
[0x10] 03 05 00 0C 00 00 01 0D 6D 38 00 00 00 00 00 00
[0x20] 05 00 0C 00 00 01 0D 6D 38 00 00 00 00 00 00 14
[0x30] 00 0C 00 00 01 0D 6D 38 00 00 00 00 00 00 14 03
[0x40] 0C 00 00 01 0D 6D 38 00 00 00 00 00 00 14 03 0F
[0x50] 00 00 01 0D 6D 38 00 00 00 00 00 00 14 03 0F C0
[0x60] 00 01 0D 6D 38 00 00 00 00 00 00 14 03 0F C0 0A
[0x70] 01 0D 6D 38 00 00 00 00 00 00 14 03 0F C0 0A 0B