Skip to content

chrta/sip_call

Repository files navigation

ESP32 door bell to sip call

On startup the application associates with the compiled in wlan access point and registers on the SIP server.

The project also contains a http server to perform firmware updates by uploading the firmware bin file.

Once a signal is detected on the selected GPIO, a call is initiated to a target number. On the phone, the custom string is displayed. After the configured timeout is elapsed, the call is canceled. If the signal is detected again, before the timer is elapsed, the timer is started again.

Tested with:

  • AVM Fritzbox 7390
  • AVM Fritzbox 7490 (Firmware 7.28)
  • AVM Fritzbox 7590
  • local FreeSWITCH installation

Programming

The source code is mixed C and C++.

This application is to be used with Espressif IoT Development Framework (ESP-IDF). It is tested with a version after v5.1 (rev b4268c874a4cf8fcf7c0c4153cffb76ad2ddda4e)

Please check ESP-IDF docs for getting started instructions.

Building

The project now uses cmake, so after initializing your environment with the relevant variables from esp-idf you can use idf.py to build, flash etc:

cd <this project's root dir>
idf.py menuconfig
idf.py build
idf.py flash monitor

To build for another ESP32 soc, e.g. the ESP32C3:

cd <this project's root dir>
idf.py set-target esp32c3
idf.py menuconfig
idf.py build
idf.py flash monitor

See Selecting soc build target for more details.

To build this project for the pc (linux, e.g. ubuntu or fedora), a sample (not all features are supported, yet):

mkdir <build dir>
cd <build dir>
cmake <this project's root dir>/native
make

The sip server configuration must be done in the defines of the file <this project's root dir>/native/main.cpp.

The following libraries are required for this (e.g. on fedora):

sudo dnf install asio-devel mbedtls-devel

Code formatting

Clang-format is used to format the code. The settings are stored in .clangformat. The format of external files, e.g. components/sip_client/include/boost/sml.hpp (boost-ext/sml) should not be changed. To run clang-format (e.g. version 12) over all files:

find . -regex '.*\.\(cpp\|cc\|cxx\|h\)' -exec clang-format -style=file -i {} \;

Hardware

An ESP32 board can be used. Only one external GPIO (input is sufficient) must be available, to detect the call trigger. To test this, two PC817 opto coupler are used to detect the AC signal (about 12V from the bell transformer). The input diodes of the opto couplers are connected in parallel and opposing directions. In series, a 2k Resistor is used. This may have to be tweaked according to the input voltage. The output transistors of the opto couplers are connected in parallel in the same polarity to pull the signal to ground, if a current flows through one of the input diodes. A pull up resistor (either internal in the ESP32 or external) must be used to pull the signal to 3V3 if no input current is detected and the output transistors are switched off.

Instead of two PC817 opto couplers, one PC814 can be used to detect the AC signal. Because of the different CTR, the resistor values must be tweaked. If it is sufficient to only detect one half-wave of the AC signal (this is normally the case) one PC817 opto coupler and a simple diode (e.g. 1N4148) is sufficient. The diode ensures that the voltage of the input diode of the opto coupler is not above the threshold. The 1N4148 must be connected anti-parallel to the input diode of the PC817.

If the bell transformer delivers enough power, the ESP32 can be powered from it. A bridge rectifier, a big capacitor and a cheap switching regulator board can be used for that.

License

If not otherwise specified, code in this repository is Copyright (C) 2017-2021 Christian Taedcke <hacking@taedcke.com>, licensed under the Apache License 2.0 as described in the file LICENSE.

Misc Information

On the AVM Fritzbox the number **9 can be used to let all connected phones ring.

About

SIP client for ESP32 to initiate a phone call from a door bell

Topics

Resources

License

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published

Contributors 4

  •  
  •  
  •  
  •