###A lua based firmware for wifi-soc esp8266
- Build on ESP8266 NONOS SDK 1.4.0
- Lua core based on eLua project
- cjson based on lua-cjson
- File system based on spiffs
- Open source development kit for NodeMCU nodemcu-devkit-v0.9 nodemcu-devkit-v1.0
- Easy to program wireless node and/or Access Point
- Based on Lua 5.1.4 (without debug, os module.)
- Event-driven programming model preferred
- Built-in modules: node, json, file, timer, pwm, i2c, spi, onewire, net, mqtt, coap, gpio, wifi, adc, uart, bit, u8g, ucg, ws2801, ws2812, crypto, dht, rtc, sntp, bmp085, tls2561, hx711 and system api.
- Both Integer (less memory usage) and Float version firmware provided.
| Resource | Location |
|---|---|
| Developer Wiki | https://github.com/nodemcu/nodemcu-firmware/wiki |
| API docs | NodeMCU api |
| Home | nodemcu.com |
| BBS | Chinese BBS |
| Docs | NodeMCU docs |
| Tencent QQ group | 309957875 |
| Windows flash tool | nodemcu-flasher |
| Linux flash tool | Esptool |
| ESPlorer GUI | https://github.com/4refr0nt/ESPlorer |
| NodeMCU Studio GUI | https://github.com/nodemcu/nodemcu-studio-csharp |
Because Lua is a high level language and several modules are built into the firmware, you can very easily program your ESP8266. Here are some examples!
ip = wifi.sta.getip()
print(ip)
--nil
wifi.setmode(wifi.STATION)
wifi.sta.config("SSID", "password")
ip = wifi.sta.getip()
print(ip)
--192.168.18.110 pin = 1
gpio.mode(pin, gpio.OUTPUT)
gpio.write(pin, gpio.HIGH)
print(gpio.read(pin)) -- A simple http client
conn=net.createConnection(net.TCP, 0)
conn:on("receive", function(conn, payload) print(payload) end)
conn:connect(80, "115.239.210.27")
conn:send("GET / HTTP/1.1\r\nHost: www.baidu.com\r\n"
.. "Connection: keep-alive\r\nAccept: */*\r\n\r\n") -- A simple http server
srv=net.createServer(net.TCP)
srv:listen(80, function(conn)
conn:on("receive", function(conn,payload)
print(payload)
conn:send("<h1> Hello, NodeMCU.</h1>")
end)
conn:on("sent", function(conn) conn:close() end)
end)-- init mqtt client with keepalive timer 120sec
m = mqtt.Client("clientid", 120, "user", "password")
-- setup Last Will and Testament (optional)
-- Broker will publish a message with qos = 0, retain = 0, data = "offline"
-- to topic "/lwt" if client doesn't send keepalive packet
m:lwt("/lwt", "offline", 0, 0)
m:on("connect", function(con) print("connected") end)
m:on("offline", function(con) print("offline") end)
-- on publish message receive event
m:on("message", function(conn, topic, data)
print(topic .. ":")
if data ~= nil then
print(data)
end
end)
-- m:connect(host, port, secure, auto_reconnect, function(client) end)
-- for secure: m:connect("192.168.11.118", 1880, 1, 0)
-- for auto-reconnect: m:connect("192.168.11.118", 1880, 0, 1)
m:connect("192.168.11.118", 1880, 0, 0, function(conn) print("connected") end)
-- subscribe to topic with qos = 0
m:subscribe("/topic", 0, function(conn) print("subscribe success") end)
-- or subscribe multiple topics (topic/0, qos = 0; topic/1, qos = 1; topic2, qos = 2)
-- m:subscribe({["topic/0"]=0,["topic/1"]=1,topic2=2}, function(conn) print("subscribe success") end)
-- publish a message with data = hello, QoS = 0, retain = 0
m:publish("/topic", "hello", 0, 0, function(conn) print("sent") end)
m:close(); -- if auto-reconnect == 1, it will disable auto-reconnect and then disconnect from host.
-- you can call m:connect again
-- a udp server
s=net.createServer(net.UDP)
s:on("receive", function(s, c) print(c) end)
s:listen(5683)
-- a udp client
cu=net.createConnection(net.UDP)
cu:on("receive", function(cu, c) print(c) end)
cu:connect(5683, "192.168.18.101")
cu:send("hello") function led(r, g, b)
pwm.setduty(1, r)
pwm.setduty(2, g)
pwm.setduty(3, b)
end
pwm.setup(1, 500, 512)
pwm.setup(2, 500, 512)
pwm.setup(3, 500, 512)
pwm.start(1)
pwm.start(2)
pwm.start(3)
led(512, 0, 0) -- red
led(0, 0, 512) -- blue lighton=0
tmr.alarm(1, 1000, 1, function()
if lighton==0 then
lighton=1
led(512, 512, 512)
else
lighton=0
led(0, 0, 0)
end
end) --init.lua will be executed
file.open("init.lua", "w")
file.writeline([[print("Hello, do this at the beginning.")]])
file.close()
node.restart() -- this will restart the module. -- a simple telnet server
s=net.createServer(net.TCP, 180)
s:listen(2323, function(c)
function s_output(str)
if(c~=nil)
then c:send(str)
end
end
node.output(s_output, 0) -- re-direct output to function s_ouput.
c:on("receive", function(c, l)
node.input(l) -- works like pcall(loadstring(l)) but support multiples separate lines
end)
c:on("disconnection", function(c)
node.output(nil) -- un-register the redirect output function, output goes to serial
end)
print("Welcome to NodeMCU world.")
end)There are several options for building the NodeMCU firmware.
Please try Marcel's NodeMCU custom build cloud service and you can choose only the modules you need, and download the firmware once built.
NodeMCU custom builds can build from all active branches (with the latest fixes).
See https://hub.docker.com/r/marcelstoer/nodemcu-build/
This Docker image includes the build toolchain and SDK. You just run the Docker image with your checked-out NodeMCU firmware repository (this one).
You will need to see BUILD OPTIONS below, to configure the firmware before building.
See BUILD OPTIONS below, to configure the firmware before building.
- unrar
- GNU autoconf, automake, libtool
- GNU gcc, g++, make
- GNU flex, bison, gawk, sed
- python, python-serial, libexpat-dev
- srecord
- The esp-open-sdk from https://github.com/pfalcon/esp-open-sdk
Assuming NodeMCU firmware is checked-out to /opt/nodemcu-firmware:
git clone --recursive https://github.com/pfalcon/esp-open-sdk.git /opt/esp-open-sdk
cd /opt/esp-open-sdk
make STANDALONE=y
PATH=/opt/esp-open-sdk/xtensa-lx106-elf/bin:$PATH
cd /opt/nodemcu-firmware
makeDisable modules you won't be using, to reduce firmware size on flash and free more RAM. The ESP8266 is quite limited in available RAM, and running out can cause a system panic.
Comment-out the #define statement for unused modules. Example:
#ifdef LUA_USE_MODULES
#define LUA_USE_MODULES_NODE
#define LUA_USE_MODULES_FILE
#define LUA_USE_MODULES_GPIO
#define LUA_USE_MODULES_WIFI
#define LUA_USE_MODULES_NET
#define LUA_USE_MODULES_PWM
#define LUA_USE_MODULES_I2C
#define LUA_USE_MODULES_SPI
#define LUA_USE_MODULES_TMR
#define LUA_USE_MODULES_ADC
#define LUA_USE_MODULES_UART
#define LUA_USE_MODULES_OW
#define LUA_USE_MODULES_BIT
#define LUA_USE_MODULES_MQTT
// #define LUA_USE_MODULES_COAP
// #define LUA_USE_MODULES_U8G
// #define LUA_USE_MODULES_WS2801
// #define LUA_USE_MODULES_WS2812
// #define LUA_USE_MODULES_CJSON
#define LUA_USE_MODULES_CRYPTO
#define LUA_USE_MODULES_RC
#define LUA_USE_MODULES_DHT
#define LUA_USE_MODULES_RTCMEM
#define LUA_USE_MODULES_RTCTIME
#define LUA_USE_MODULES_RTCFIFO
#define LUA_USE_MODULES_SNTP
// #define LUA_USE_MODULES_BMP085
#define LUA_USE_MODULES_TSL2561
// #define LUA_USE_MODULES_HX711
#endif /* LUA_USE_MODULES */Identify your firmware builds by editing app/include/user_version.h
#define NODE_VERSION "NodeMCU 1.4.0+myname"
#ifndef BUILD_DATE
#define BUILD_DATE "YYYYMMDD"
#endifThe initial baud rate at boot time is 9600 bps, but you can change this by
editing app/include/user_config.h and change BIT_RATE_DEFAULT, e.g.:
#define BIT_RATE_DEFAULT BIT_RATE_115200To enable runtime debug messages to serial console, edit app/include/user_config.h
#define DEVELOP_VERSIONDEVELOP_VERSION changes the startup baud rate to 74880.
You can use the nodemcu-flasher to burn the firmware.
Esptool is a python utility which can read and write the flash in an ESP8266 device. See https://github.com/themadinventor/esptool
To enable ESP8266 firmware flashing, the GPIO0 pin must be pulled low before the device is reset. Conversely, for a normal boot, GPIO0 must be pulled high or floating.
If you have a NodeMCU Development Kit then you don't need to do anything, as the USB connection can pull GPIO0 low by asserting DTR, and reset your board by asserting RTS.
If you have an ESP-01 or other device without inbuilt USB, you will need to enable flashing yourself by pulling GPIO0 low or pressing a "flash" switch.
If you got your firmware from NodeMCU custom builds then you can flash that file directly to address 0x00000.
Otherwise, if you built your own firmware from source code:
- bin/0x00000.bin to 0x00000
- bin/0x10000.bin to 0x10000
Also, in some special circumstances, you may need to flash blank.bin or esp_init_data_default.bin to various addresses on the flash (depending on flash size and type).
If upgrading from spiffs version 0.3.2 to 0.3.3 or later, or after flashing any new firmware (particularly one with a much different size), you may need to run file.format() to re-format your flash filesystem.
You will know if you need to do this because your flash files disappeared, or they exist but seem empty, or data cannot be written to new files.
NodeMCU serial interface uses 9600 baud at boot time. To increase the speed after booting, issue uart.setup(0,115200,8,0,1,1) (ESPlorer will do this automatically when changing the speed in the dropdown list).
If the device panics and resets at any time, errors will be written to the serial interface at 115200 bps.
Victor Brutskiy's ESPlorer is written in Java, is open source and runs on most platforms such as Linux, Windows, Mac OS, etc.
- Edit Lua scripts and run on the ESP8266 and save to its flash
- Serial console log
- Also supports original AT firmware (reading and setting WiFi modes, etc)
NodeMCU Studio is written in C# and supports Windows. This software is open source and can write lua files to filesystem.
####Use DS18B20 module extends your esp8266
-- read temperature with DS18B20
node.compile("ds18b20.lua") -- run this only once to compile and save to "ds18b20.lc"
t=require("ds18b20")
t.setup(9)
addrs=t.addrs()
-- Total DS18B20 numbers, assume it is 2
print(table.getn(addrs))
-- The first DS18B20
print(t.read(addrs[1],t.C))
print(t.read(addrs[1],t.F))
print(t.read(addrs[1],t.K))
-- The second DS18B20
print(t.read(addrs[2],t.C))
print(t.read(addrs[2],t.F))
print(t.read(addrs[2],t.K))
-- Just read
print(t.read())
-- Just read as centigrade
print(t.read(nil,t.C))
-- Don't forget to release it after use
t = nil
ds18b20 = nil
package.loaded["ds18b20"]=nil####Operate a display with u8glib u8glib is a graphics library with support for many different displays. The nodemcu firmware supports a subset of these. Both I2C and SPI:
- sh1106_128x64
- ssd1306 - 128x64 and 64x48 variants
- ssd1309_128x64
- ssd1327_96x96_gr
- uc1611 - dogm240 and dogxl240 variants
SPI only:
- ld7032_60x32
- pcd8544_84x48
- pcf8812_96x65
- ssd1322_nhd31oled - bw and gr variants
- ssd1325_nhd27oled - bw and gr variants
- ssd1351_128x128 - gh and hicolor variants
- st7565_64128n - variants 64128n, dogm128/132, lm6059/lm6063, c12832/c12864
- uc1601_c128032
- uc1608 - 240x128 and 240x64 variants
- uc1610_dogxl160 - bw and gr variants
- uc1611 - dogm240 and dogxl240 variants
- uc1701 - dogs102 and mini12864 variants
U8glib v1.18.1
#####I2C connection Hook up SDA and SCL to any free GPIOs. Eg. u8g_graphics_test.lua expects SDA=5 (GPIO14) and SCL=6 (GPIO12). They are used to set up nodemcu's I2C driver before accessing the display:
sda = 5
scl = 6
i2c.setup(0, sda, scl, i2c.SLOW)#####SPI connection The HSPI module is used, so certain pins are fixed:
- HSPI CLK = GPIO14
- HSPI MOSI = GPIO13
- HSPI MISO = GPIO12 (not used)
All other pins can be assigned to any available GPIO:
- CS
- D/C
- RES (optional for some displays)
Also refer to the initialization sequence eg in u8g_graphics_test.lua:
spi.setup(1, spi.MASTER, spi.CPOL_LOW, spi.CPHA_LOW, 8, 8)#####Library usage The Lua bindings for this library closely follow u8glib's object oriented C++ API. Based on the u8g class, you create an object for your display type.
SSD1306 via I2C:
sla = 0x3c
disp = u8g.ssd1306_128x64_i2c(sla)SSD1306 via SPI:
cs = 8 -- GPIO15, pull-down 10k to GND
dc = 4 -- GPIO2
res = 0 -- GPIO16, RES is optional YMMV
disp = u8g.ssd1306_128x64_hw_spi(cs, dc, res)This object provides all of u8glib's methods to control the display. Again, refer to u8g_graphics_test.lua to get an impression how this is achieved with Lua code. Visit the u8glib homepage for technical details.
#####Displays I2C and HW SPI based displays with support in u8glib can be enabled. To get access to the respective constructors, add the desired entries to the I2C or SPI display tables in app/include/u8g_config.h:
#define U8G_DISPLAY_TABLE_I2C \
U8G_DISPLAY_TABLE_ENTRY(ssd1306_128x64_i2c) \
#define U8G_DISPLAY_TABLE_SPI \
U8G_DISPLAY_TABLE_ENTRY(ssd1306_128x64_hw_spi) \
U8G_DISPLAY_TABLE_ENTRY(pcd8544_84x48_hw_spi) \
U8G_DISPLAY_TABLE_ENTRY(pcf8812_96x65_hw_spi) \An exhaustive list of available displays can be found in the u8g module wiki entry.
#####Fonts u8glib comes with a wide range of fonts for small displays. Since they need to be compiled into the firmware image, you'd need to include them in app/include/u8g_config.h and recompile. Simply add the desired fonts to the font table:
#define U8G_FONT_TABLE \
U8G_FONT_TABLE_ENTRY(font_6x10) \
U8G_FONT_TABLE_ENTRY(font_chikita)They'll be available as u8g.<font_name> in Lua.
#####Bitmaps
Bitmaps and XBMs are supplied as strings to drawBitmap() and drawXBM(). This off-loads all data handling from the u8g module to generic methods for binary files. See u8g_bitmaps.lua.
In contrast to the source code based inclusion of XBMs into u8glib, it's required to provide precompiled binary files. This can be performed online with Online-Utility's Image Converter: Convert from XBM to MONO format and upload the binary result with nodemcu-uploader.py.
#####Unimplemented functions
- Cursor handling
- disableCursor()
- enableCursor()
- setCursorColor()
- setCursorFont()
- setCursorPos()
- setCursorStyle()
- General functions
- setContrast()
- setPrintPos()
- setHardwareBackup()
- setRGB()
- setDefaultMidColor()
####Operate a display with ucglib Ucglib is a graphics library with support for color TFT displays.
Ucglib v1.3.3
#####SPI connection The HSPI module is used, so certain pins are fixed:
- HSPI CLK = GPIO14
- HSPI MOSI = GPIO13
- HSPI MISO = GPIO12 (not used)
All other pins can be assigned to any available GPIO:
- CS
- D/C
- RES (optional for some displays)
Also refer to the initialization sequence eg in GraphicsTest.lua:
spi.setup(1, spi.MASTER, spi.CPOL_LOW, spi.CPHA_LOW, 8, 8)#####Library usage The Lua bindings for this library closely follow ucglib's object oriented C++ API. Based on the ucg class, you create an object for your display type.
ILI9341 via SPI:
cs = 8 -- GPIO15, pull-down 10k to GND
dc = 4 -- GPIO2
res = 0 -- GPIO16, RES is optional YMMV
disp = ucg.ili9341_18x240x320_hw_spi(cs, dc, res)This object provides all of ucglib's methods to control the display. Again, refer to GraphicsTest.lua to get an impression how this is achieved with Lua code. Visit the ucglib homepage for technical details.
#####Displays To get access to the display constructors, add the desired entries to the display table in app/include/ucg_config.h:
#define UCG_DISPLAY_TABLE \
UCG_DISPLAY_TABLE_ENTRY(ili9341_18x240x320_hw_spi, ucg_dev_ili9341_18x240x320, ucg_ext_ili9341_18) \
UCG_DISPLAY_TABLE_ENTRY(st7735_18x128x160_hw_spi, ucg_dev_st7735_18x128x160, ucg_ext_st7735_18) \#####Fonts ucglib comes with a wide range of fonts for small displays. Since they need to be compiled into the firmware image, you'd need to include them in app/include/ucg_config.h and recompile. Simply add the desired fonts to the font table:
#define UCG_FONT_TABLE \
UCG_FONT_TABLE_ENTRY(font_7x13B_tr) \
UCG_FONT_TABLE_ENTRY(font_helvB12_hr) \
UCG_FONT_TABLE_ENTRY(font_helvB18_hr) \
UCG_FONT_TABLE_ENTRY(font_ncenR12_tr) \
UCG_FONT_TABLE_ENTRY(font_ncenR14_hr)They'll be available as ucg.<font_name> in Lua.
####Control a WS2812 based light strip
-- set the color of one LED on GPIO2 to red
ws2812.writergb(4, string.char(255, 0, 0))
-- set the color of 10 LEDs on GPIO0 to blue
ws2812.writergb(3, string.char(0, 0, 255):rep(10))
-- first LED green, second LED white
ws2812.writergb(4, string.char(0, 255, 0, 255, 255, 255))####coap client and server
-- use copper addon for firefox
cs=coap.Server()
cs:listen(5683)
myvar=1
cs:var("myvar") -- get coap://192.168.18.103:5683/v1/v/myvar will return the value of myvar: 1
all='[1,2,3]'
cs:var("all", coap.JSON) -- sets content type to json
-- function should tack one string, return one string.
function myfun(payload)
print("myfun called")
respond = "hello"
return respond
end
cs:func("myfun") -- post coap://192.168.18.103:5683/v1/f/myfun will call myfun
cc = coap.Client()
cc:get(coap.CON, "coap://192.168.18.100:5683/.well-known/core")
cc:post(coap.NON, "coap://192.168.18.100:5683/", "Hello")####cjson
-- Note that when cjson deal with large content, it may fails a memory allocation, and leaks a bit of memory.
-- so it's better to detect that and schedule a restart.
--
-- Translate Lua value to/from JSON
-- text = cjson.encode(value)
-- value = cjson.decode(text)
json_text = '[ true, { "foo": "bar" } ]'
value = cjson.decode(json_text)
-- Returns: { true, { foo = "bar" } }
value = { true, { foo = "bar" } }
json_text = cjson.encode(value)
-- Returns: '[true,{"foo":"bar"}]'####Read an HX711 load cell ADC. Note: currently only chanel A with gain 128 is supported. The HX711 is an inexpensive 24bit ADC with programmable 128x, 64x, and 32x gain.
-- Initialize the hx711 with clk on pin 5 and data on pin 6
hx711.init(5,6)
-- Read ch A with 128 gain.
raw_data = hx711.read(0)####Universal DHT Sensor support Support DHT11, DHT21, DHT22, DHT33, DHT44, etc. Use all-in-one function to read DHT sensor.
pin = 5
status,temp,humi,temp_decimial,humi_decimial = dht.readxx(pin)
if( status == dht.OK ) then
-- Integer firmware using this example
print(
string.format(
"DHT Temperature:%d.%03d;Humidity:%d.%03d\r\n",
math.floor(temp),
temp_decimial,
math.floor(humi),
humi_decimial
)
)
-- Float firmware using this example
print("DHT Temperature:"..temp..";".."Humidity:"..humi)
elseif( status == dht.ERROR_CHECKSUM ) then
print( "DHT Checksum error." );
elseif( status == dht.ERROR_TIMEOUT ) then
print( "DHT Time out." );
end