-
Notifications
You must be signed in to change notification settings - Fork 314
New issue
Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.
By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.
Already on GitHub? Sign in to your account
all three gps sattelites get disabled when enabling BeiDou #1914
Comments
probably an issue with INAV itself. |
I’m sure this is expected behaviour. Either your GPS module doesn’t support having 4 GNSS. Or I believe I’ve read that BeiDou and GLONASS share something, that means they can’t be selected at the same time. Maybe Configurator needs some kind of warning? @mmosca could we get some clarification? |
Alright, reopened this one and closed the issue in inav. |
The valid combinations are defined by the gps and are not known to inav. If we add that to the configurator it may prevent other valid use cases. []s,Marcelo Bezerra ***@***.***>On 7 Dec 2023, at 18:09, tippfehlr ***@***.***> wrote:
Alright, reopened this one and closed the issue in inav.
If indeed glonass and BeiDou share something, maybe disable the other switch to indicate that only one is supported.
—Reply to this email directly, view it on GitHub, or unsubscribe.You are receiving this because you were mentioned.Message ID: ***@***.***>
|
I was meaning just an info box for explaining that. Not actually denying enabling certain clusters. Is that documented anywhere? |
The data sheet for each gps model. The status command does report the maximum number of constellations a gps supports though, and I am sure that his gps does not say 4. (Gps counts as one, btw)[]s,Marcelo Bezerra ***@***.***>On 8 Dec 2023, at 08:17, Darren Lines ***@***.***> wrote:
I was meaning just an info box for explaining that. Not actually denying enabling certain clusters. Is that documented anywhere?
—Reply to this email directly, view it on GitHub, or unsubscribe.You are receiving this because you were mentioned.Message ID: ***@***.***>
|
ok, so my gps (HGLRC M100 Mini) does indeed only do 3 at a time.
|
That is a hard thing to say these days. Glonass is provided by a country
that is engaged in a war in europe. beidou has global coverage, but works
better in the asia pacific region.
I would say that your gps defaults of galileo and beidou is probably a good
combo.
…On Fri, Dec 8, 2023 at 3:51 PM tippfehlr ***@***.***> wrote:
# status
INAV/SPEEDYBEEF405WING 7.0.0 Dec 5 2023 / 11:06:36 (895a4f31)
GCC-10.3.1 20210824 (release)
System Uptime: 44 seconds
Current Time: 2041-06-28T03:04:00.000+02:00
Voltage: 0.00V (0S battery - NOT PRESENT)
CPU Clock=168MHz, GYRO=ICM42605, ACC=ICM42605, BARO=SPL06
STM32 system clocks:
SYSCLK = 168 MHz
HCLK = 168 MHz
PCLK1 = 42 MHz
PCLK2 = 84 MHz
Sensor status: GYRO=OK, ACC=OK, MAG=NONE, BARO=OK, RANGEFINDER=NONE, OPFLOW=NONE, GPS=OK
ESC Temperature(s): Motor Count = 2
ESC 0: 0°C, ESC 1: 0°C,
SD card: Manufacturer 0x1b, 994816kB, 04/2008, v1.0, '00000'
Filesystem: Ready
Stack size: 6144, Stack address: 0x10010000, Heap available: 1728
I2C Errors: 0, config size: 9541, max available config: 131072
ADC channel usage:
BATTERY : configured = ADC 1, used = ADC 1
RSSI : configured = ADC 4, used = none
CURRENT : configured = ADC 2, used = ADC 2
AIRSPEED : configured = ADC 3, used = none
System load: 12, cycle time: 1035, PID rate: 966, RX rate: 9, System rate: 9
Arming disabled flags: NAV RX CLI
OSD: MAX7456 [30 x 16]
VTX: band: A, chan: 2, power: 1 (25 mW), freq: 5845 MHz
GPS: HW Version: UBLOX10 Proto: 34.09 Baud: 115200
GNSS Capabilities:
GNSS Provider active/default
GPS 1/1
Galileo 1/1
BeiDou 0/1
Glonass 1/0
Max concurrent: 3
Max concurrent: 3
ok, so my gps (HGLRC M100 Mini) does indeed only do 3 at a time.
And BeiDou and Glonass don’t work at the same time, doesn’t matter is
Galileo is enabled or not.
- If this is confirmed, wouldn’t disabling the other switch make it
clear?
- And I don’t know if there are gps with less than 3 max concurrent
gps systems, if yes maybe display used/max gps systems.
- I’m in Europe/Germany, does it matter which one I activate? Or
should I disable both?
—
Reply to this email directly, view it on GitHub
<#1914 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AFTWX5F5Z637PWF73GY3WU3YIMSPBAVCNFSM6AAAAABALIMYYOVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTQNBXGMYTSMRSHE>
.
You are receiving this because you were mentioned.Message ID:
***@***.***>
|
That is probably ok. A basic warning that not all combinations of constellations may be supported by a particular GPS unit and that the settings will revert to default on invalid configurations would at least avoid more issues like this. |
I think showing the actual capabilities of the gps unit is much more user friendly than letting the user figure out what works and what doesn’t. |
There is no way to find out before hand what combinations are valid, but if
you do find a way in the ublox documentation, please share and we may look
into improving the configurator behavior.
…On Fri, Dec 8, 2023 at 11:18 PM tippfehlr ***@***.***> wrote:
I think showing the actual capabilities of the gps unit is much more user
friendly than letting the user figure out what works and what doesn’t.
Is there a reason you are against disabling the options? The note can
still be in the tooltips.
—
Reply to this email directly, view it on GitHub
<#1914 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AFTWX5DWKLBSPZ7H5CZCHQDYIOG3XAVCNFSM6AAAAABALIMYYOVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTQNBXHEYTENBYGY>
.
You are receiving this because you were mentioned.Message ID:
***@***.***>
|
@mmosca I would just disable BeiDou/Glonass and (maybe) display a warning if |
You are assuming that combination is not valid in other gps models (current and future). |
That is true, I was assuming that it was a limitation of the gnss itself (without having done research -_-) |
When I try to enable BeiDou Sattelites (CN) via GPS tab or cli, after rebooting all three, Galileo, BeiDou and Glonass are disabled again (in ui and in cli).
Steps to reproduce:
expected result:
all three stay activated
The text was updated successfully, but these errors were encountered: