Simple Computer

Whilst reading But How Do It Know? by J. Clark Scott I felt compelled to write something to simulate the computer the book describes.

Starting from NAND gates, and moving up through to registers, RAM, the ALU, the control unit and adding I/O support, I eventually ended up with a fully functional machine.

All the components of the system are based on logic gates and the way they are connected together via the system bus.

For a write up about this project, see my blog post about it here https://djhworld.github.io/post/2019/05/21/i-dont-know-how-cpus-work-so-i-simulated-one-in-code/

Specs

• ~0.006mhz
  • at least on my machine
• 16-bit
  • the book describes an 8-bit CPU for simplicity but I wanted more RAM and there is only one system bus
• 65K RAM
• 240x160 screen resolution
• 4x 16-bit registers (R0, R1, R2, R3)

Missing features

• Interrupts, so you have to write awful polling code
  • The book does shortly describe how to extend the system to support interrupts but would involve a lot more wiring
• Stack pointer register + stack + stack manipulation instructions so nested CALL instructions won't work and registers may be left in an inconsistent state
• Hard drive
• Subtract instruction
• MOV instruction
• Floating point math (lol)
• Everything else you could think of from a modern CPU

Bonus features

• No Meltdown/SPECTRE risk
• Can easily overwrite any portion of memory without any protective mode getting in the way
• Currently incapable of accessing the internet
  • I can see how you might write a simple networking I/O adapter, although I'd imagine it would be tedious writing the assembly to get bytes in and out of it 🤔

Instructions

Instruction	Type	Description	Example
LOAD Ra, Rb	Machine	Load value of memory address in register A into register B	LOAD R1, R2
STORE Ra, Rb	Machine	Store value of register B into memory address in register A	STORE R3, R1
DATA Ra, <VALUE>	Machine	Put <VALUE> into register A. <VALUE> can either be a symbol, prefixed with % (e.g. %LINE-X) or a numeric value (e.g. 0x00F2 or 23)	DATA R3, %KEYCODE
JR Ra	Machine	Jump to instruction in memory address in register A	JR R2
JMP <LABEL>	Machine	Jump to instruction in memory address for <LABEL>	JMP startloop
JMP[CAEZ]+ <LABEL>	Machine	Jump to instruction in memory address for <LABEL> if flags register for any combination of CAEZ is true	JMPEZ endloop
CLF	Machine	Clear contents of flags register	CLF
IN <MODE>, Ra	Machine	Request input from IO device to Register A	IN Data, R3
OUT <MODE>, Ra	Machine	Send output to IO device for register A	OUT Addr, R2
ADD Ra, Rb	Machine	16 bit addition of two registers	ADD R0, R2
SHR Ra	Machine	Shift right register A	SHR R0
SHL Ra	Machine	Shift left register A	SHL R0
NOT Ra	Machine	Bitwise NOT on register A	NOT R2
AND Ra, Rb	Machine	Bitwise AND on two registers	AND R2, R3
OR Ra, Rb	Machine	Bitwise OR on two registers	OR R0, R1
XOR Ra, Rb	Machine	Bitwise XOR on two registers	XOR R1, R0
CMP Ra, Rb	Machine	Compare register A and register B (will set flags register)	CMP R1, R2
CALL <LABEL>	Pseudo	Call a subroutine. This will jump to the subroutine, on completion, the subroutine should jump back and continue from the next instruction. Note: there is no stack functionality here so all registers may be in a different state at the end of the subroutine.	CALL pollKeyboard

I/O devices

The following I/O devices are supported by the computer.

Device	Address
Keyboard	0x000F
Display	0x0007

Memory layout

There is no memory management unit or protected areas of memory.

However the assembler and simulator will start executing user code from offset 0x0500

Assembler

Machine code can be written in text and assembled using a crude assembler I wrote.

See assembler for more information.

Building

Requirements

• go 1.12+
• GLFW 3.2+

Building:

make

There are some unit tests that take 30-45 seconds to run through, by running

make test

Running

The computer can be run using the wrapper tool I wrote that utilises GLFW for I/O functionality.

Example of running the brush.bin program

./bin/simulator -bin _programs/brush.bin

Example programs

You can see some example programs I wrote under _programs/, note the ASM code I wrote for these is very bad and I lost my sanity a bit when writing them.

Why bother?

I'm taking myself on a journey, a hardware journey you might say. I want to understand how computers work at a lower level but not quite low enough for the physics/digital electronics side of things.

Just enough to see all the pieces of the system interacting. I remember doing a lot of this stuff in school but I'd say my education seemed to focus on the concepts (Von-Neumann architecture, fetch-decode-execute) rather than the actual construction of a CPU.

This simple computer is the start of that journey, it's actually been a very rewarding little project.

I hope to move onto playing around with X86/ARM/RISC-V next although I suspect it will be quite a leap (of faith)