I am building a 300mm Voron 2.4.
Ordered parts from Amazon, West3D, DigMach, KB-3D, Fabreeko, Printed Solid and Mandala Rose Works.
| Part | Source |
|---|---|
| Fasteners | |
| Stainless Steel Fastener Kit for Voron 2.4 | West3D / Amazon |
| Motion | |
| Voron 2.4 Motor Kit by OMC / Stepperonline | West3D / Amazon |
| POWGE & GATES VORON 2.4 Motion Set - Black or Silver | West3D / Amazon |
| MGN9H linear rail × 8 350mm | DigMach |
| Electronics | |
| Wiring Harness for Voron 2.4 / Trident | West3D |
| 6ft 18 AWG Power Cord (C13) UL-Listed Cable | West3D |
| Fuse 8A 250V Holder Cartridge 5 X 20mm Glass × 2 | West3D |
| TycoElectronics - 10EHG1-2 Filtered Power Inlet | West3D |
| Omron G3NA-210B 24V Solid State Relay (SSR) | West3D |
| Mean Well RS-25-5 25W Power Supply (PSU) | West3D |
| Mean Well LRS-200-24 200W 24V 8.8A Power Supply (PSU) | West3D |
| Rocker Switch DPST 16A On-Off | West3D |
| PL-08N2 Inductive Probe | Amazon |
| GDSTIME DC 24V 60x60x20 Axial Fan GDA6020 × 3 | West3D |
| Din Rails | Amazon |
| Din Rail Bracket Solid State Relay (SSR) | Amazon |
| Omron Micro Switch (D2F-01L) × 3 | West3D |
| 125C Cutoff 15A Thermal Fuse | West3D |
| 24V Heater Tube | Amazon |
| BAT85 Diode (*Not needed with Octopus Pro) | West3D |
| Molex Microfit 3.0 Connectors - various | KB-3D |
| *Voron Afterburner Toolhead PCB - V3.rabbit | KB-3D |
| *Voron Hall Effect X/Y Endstop PCB Assembled | West3D / Amazon |
| *Sexbolt Z-Endstop Fully Assembled - Hartk | West3D |
| Controller | |
| BigTreeTech Octopus Pro v1.0 | Amazon |
| BigTreeTech TMC2209 Stepper Drivers x 8 | Amazon |
| BigTreeTech Mini12864 LCD Graphic Smart Display | Amazon |
| Frame | |
| Angle Corner Connector 90 degree × 4 | West3D |
| Misc | |
| Rubber Compressor Feet 48x18mm | Amazon |
| Bowden Coupler for 4mm OD PTFE Tube | West3D |
| Bowden / PTFE Tube 4mm OD 3mm ID | West3D |
| *Voron Logo Sticker Decal | West3D |
| *Nevermore Carbon filtration media bags | Fabreeko |
| Cables | |
| VORON 2.4 Cable Chains Set 300mm | Amazon |
| Panels | |
| Voron 2.4 Panel Kit 300mm Side, Front & Top Only | DigMach |
| Voron V2 Panel Set Made From Aluminum Composite Material | Printed Solid |
| Build Plate | |
| Voron 300 Ultraflat Bed | Mandala Rose Works |
| Keenovo Silicone Heater 240x240 600W 120V | Amazon |
| Magnetic Flex Plate Double-Sided (Texture/Smooth) | Amazon |
* Mod only
I decided on Hartk1213's "Voron Afterburner Toolhead Board v3.rabbit (also known as ERCF PCB board)" since one day I may add a ERCF Filament changer.
You will also need a new PCB cover from here
Since the PCB has a temperature sensor built in, I ended up using this cover with air vents
Wiring Diagram here
Pinout
24V - HE0 +V
GND - PSU -V (NOT MAINS GND)
PROBE/ABL - Probe Signal Pin
HE0 - Hotend Heater -V
CT - Chamber Thermistor Signal Pin (TH1)
PCF - Part Cooling Fan -V
HEF - Hotend Cooling Fan -V
AGND - Hotend Thermistor -V
TH0 - Hotend Thermistor Signal Pin (TH0)
XES - X Endstop Signal Pin
S1A - Red Stepper Wire
S2A - Green Stepper Wire
S1B - Blue Stepper Wire
S2B - Black Stepper WireFrame:
https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/alanho/BTT_PITFT50_v2_Mount
https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/deepfriedheroin/v2_bed_wagos
Use the bed Wago mount to make the bed wiring pluggable:
Instead of the extractor filter and fan I am installing the Nevermore Micro V5 Duo mod.