This is a replacement for the
vpnc-script
used by OpenConnect or
VPNC.
Instead of trying to copy the behavior of standard corporate VPN clients, which normally reroute all your network traffic through the VPN, this one tries to minimize your contact with an intrusive VPN. This is also known as a split-tunnel VPN, since it splits your traffic between the VPN tunnel and your normal network interfaces.
vpn-slice
makes it easy to set up a split-tunnel VPN:
- It only routes traffic for specific hosts or subnets through the VPN.
- It automatically looks up named hosts, using the VPN's DNS servers,
and adds entries for them to your
/etc/hosts
(which it cleans up after VPN disconnection), however it does not otherwise alter your/etc/resolv.conf
at all.
If you are using a VPN to route all your traffic for privacy reasons (or to avoid censorship in repressive countries), then you do not want to use this.
The purpose of this tool is almost the opposite; it makes it easy to connect to a VPN while minimizing the traffic that passes over the VPN.
This is for people who have to connect to the high-security VPNs of corporations or other bureaucracies (which monitor and filter and otherwise impede network traffic), and thus wish to route as little traffic as possible through those VPNs.
- Python 3.3+
- Either of the following:
- Supported OSes:
You can install the latest build with pip
(make sure you are using
the Python 3.x version, usually invoked with pip3
).
You should install as root
(e.g. using sudo
), because
openconnect
or vpnc
will need to be able to invoke vpn-slice
while running as root:
$ sudo pip3 install https://github.com/dlenski/vpn-slice/archive/master.zip
On macOS, you can also install using Homebrew:
$ brew install vpn-slice
Before trying to use vpn-slice
with openconnect
or vpnc
,
check that it works properly on your platform, and can verify that it has all of
the access and dependencies that it needs (to modify /etc/hosts
, alter
routing table, etc.):
$ sudo vpn-slice --self-test
***************************************************************************
*** Self-test passed. Try using vpn-slice with openconnect or vpnc now. ***
***************************************************************************
If you run the self-test as a non-root
user, it will tell you what required
access it is unable to obtain:
$ vpn-slice --self-test
WARNING: Couldn't configure hosts provider: Cannot read/write /etc/hosts
******************************************************************************************
*** Self-test did not pass. Double-check that you are running as root (e.g. with sudo) ***
******************************************************************************************
Aborting because providers for hosts are required; use --help for more information
When you start trying to use vpn-slice
for real, you should use the
diagnostic options (e.g openconnect -s 'vpn-slice --verbose --dump'
) to troubleshoot and understand its behavior.
You should specify vpn-slice
as your connection script with
openconnect
or vpnc
. It has been tested with vpnc v0.5.3, OpenConnect
v7.06+ (Cisco AnyConnect and Juniper protocols) and v8.0+ (PAN GlobalProtect
protocol).
For example:
$ sudo openconnect gateway.bigcorp.com -u user1234 \
-s 'vpn-slice 192.168.1.0/24 hostname1 alias2=alias2.bigcorp.com=192.168.1.43'
$ cat /etc/hosts
...
192.168.1.1 dns0.tun0 # vpn-slice-tun0 AUTOCREATED
192.168.1.2 dns1.tun0 # vpn-slice-tun0 AUTOCREATED
192.168.1.57 hostname1 hostname1.bigcorp.com # vpn-slice-tun0 AUTOCREATED
192.168.1.43 alias2 alias2.bigcorp.com # vpn-slice-tun0 AUTOCREATED
or
# With most versions of vpnc, you *must* specify an absolute path
# for the disconnect hook to work correctly, due to a bug.
#
# I reported this bug, but the original maintainers no longer maintain vpnc.
# https://lists.unix-ag.uni-kl.de/pipermail/vpnc-devel/2016-August/004199.html
#
# However, some Linux distro packagers have picked up my patch in recent
# releases, e.g. Ubuntu 17.04:
# https://changelogs.ubuntu.com/changelogs/pool/universe/v/vpnc/vpnc_0.5.3r550-3/changelog
#
$ sudo vpnc config_file \
--script '/path/to/vpn-slice 192.168.1.0/24 hostname1 alias2=alias2.bigcorp.com=192.168.1.43'
Notice that vpn-slice
accepts both hostnames alone (hostname1
) as well as
host-to-IP* aliases (alias2=alias2.bigcorp.com=192.168.1.43
). The former are first looked up using the
VPN's DNS servers. Both are also added to the routing table, as well as to
/etc/hosts
(unless --no-host-names
is specified). As in this
example, multiple aliases can be specified for a single IP address.
There are many command-line options to alter the behavior of
vpn-slice
; try vpn-slice --help
to show them all.
Running with --verbose
makes it explain what it is doing, while running with
--dump
shows the environment variables passed in by the caller.
- @jagtesh's
split-tunnelling tutorial gist taught me the
basics of how to set up a split-tunnel VPN by wrapping the standard
vpnc-script
. - @apenwarr's
sshuttle has the excellent
--auto-hosts
and--seed-hosts
options. These inspired the automatic host lookup feature. - @gmacon's PR #11 substantially refactored the code to separate the OS-dependent parts more cleanly, and added macOS support.
- @joelbu's
PR #30 added support for IPv6 DNS
lookups using
dig
.
GPLv3 or later.
- Better error-explaining
- Fix timing issues
- Improve IPv6 support
- Support OSes other than Linux and macOS
- Other Unix-like operating systems should be pretty easy
- Mechanism for specifying split-exclude subnets on the command line