After zpool replace ZFS restarts resilvering process and does not finish #9551
Labels
Type: Defect
Incorrect behavior (e.g. crash, hang)
Comments
|
As the resilver is currently running: stop the ZED daemon and wait for resilver to complete? |
Ohh! i didnt mention that but i all ready did this :/ this was one of the first suggestions i read in a forum. that did not work for me. |
|
I have seen similar with zfs 0.8.1-r0-gentoo on 4.19.67_p2-r2-debian-sources-lts when turning a single drive pool into a triple mirror: after the two Detaching only one of the new mirror sides didn't help to stop resilver from restarting, I needed to detach both new mirror sides and then attach only one, wait for resilver to complete, then attach the next. Getting to a state with two drives getting resilvered at the same time was back to restart-o-mania again. No ZED running. |
12 tasks
|
Hello, i just recently looked at the print from demesg: Im not sure what that means ;( maybe someone can enlighten me? Gothard |
tonyhutter
pushed a commit
to tonyhutter/zfs
that referenced
this issue
Jan 22, 2020
If a device is participating in an active resilver, then it will have a
non-empty DTL. Operations like vdev_{open,reopen,probe}() can cause the
resilver to be restarted (or deferred to be restarted later), which is
unnecessary if the DTL is still covered by the current scan range. This
is similar to the logic in vdev_dtl_should_excise() where the DTL can
only be excised if it's max txg is in the resilvered range.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Gallagher <john.gallagher@delphix.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: John Poduska <jpoduska@datto.com>
Issue openzfs#840
Closes openzfs#9155
Closes openzfs#9378
Closes openzfs#9551
Closes openzfs#9588
tonyhutter
pushed a commit
that referenced
this issue
Jan 23, 2020
If a device is participating in an active resilver, then it will have a
non-empty DTL. Operations like vdev_{open,reopen,probe}() can cause the
resilver to be restarted (or deferred to be restarted later), which is
unnecessary if the DTL is still covered by the current scan range. This
is similar to the logic in vdev_dtl_should_excise() where the DTL can
only be excised if it's max txg is in the resilvered range.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Gallagher <john.gallagher@delphix.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: John Poduska <jpoduska@datto.com>
Issue #840
Closes #9155
Closes #9378
Closes #9551
Closes #9588
|
I have just seen potentially similar behaviour on my RAIDZ2 array. As soon as I I'll do these replaces in serial now, but it feels like the wrong answer. |
|
I'm seeing the same problem. Resilver runs in a loop, just disabled zfs-zed, need to wait ~20hours before resilvering finishes single loop. |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
System information
Describe the problem you're observing
One of my HDD drives needed to be replaced, due to not beeing recognized. my guess from the sound of the HDD that the motor inside broke.
i shut down the NAS, disconnected the HDD and replaced it with a new one, booted and "zpool replace" the drive with the new one. i did that a couple of times now for the last years if one HDD seems to have an issue and everything worked fine. but this time, the resilvering process keeps restarting, sometimes it goes above 70% some times it restarts at about 20% of the resilvering process. i also tried with a second bought HDD in case of a broken bought HDD, and replaced a 2nd time, also didnt work. i did some research but i could not figure out the problem at all and the forum hints didnt work for me.
thank you for reading and your time you use to help me, if i can provide addional information that you need just ask and i try to provide it.
Describe how to reproduce the problem
I can't tell when it will restart the resilvering process, but i just have to wait and it does not seem to stop. it keeps restarting.
Include any warning/errors/backtraces from the system logs
pool status looks like this:
event log
History Log
The text was updated successfully, but these errors were encountered: