Releases: rotorflight/rotorflight-configurator
Rotorflight Configurator Release Candidate 2.1.0-RC3
This is the third Release Candidate of the Rotorflight 2.1 Configurator.
NOTE The final 2.1.0 Configurator will be released after a few release candidates. Please don't use RCs once the final release is out.
Downloads
The download locations are:
The other components are not updated this time. Please use RC2 instead:
- Rotorflight Blackbox
- Lua Scripts for EdgeTx and OpenTx
- Lua Scripts for FrSky Ethos
- Lua Suite for FrSky Ethos
Notes
-
Rotorflight setup instructions can be found on the RF website www.rotorflight.org.
-
RF 2.1 is backward compatible with RF 2.0. You can load your configuration dump from RF 2.0 into 2.1.
-
If updating from RF1, please setup your helicopter from scratch. Follow the instructions on the website!
-
As always, please double check your configuration on the bench before flying!
Changes from 2.1.0-RC2
- Fix Board detection getting stuck in Flasher
- Fix Motors tab stalling at FC Disconnect
- Add a warning on a wrong tail calibraton value
- SBUS2 protocol hidden with 4.3.0 firmware
- Gyro chip orientation fields removed
- Help link fixed in Firmware Flasher
- German translation updated
Rotorflight Configurator Release Candidate 2.1.0-RC2
This is the second Release Candidate of the Rotorflight 2.1 Configurator.
NOTE The final 2.1.0 Configurator will be released after a few release candidates. Please don't use RCs once the final release is out.
Downloads
The download locations are:
- Rotorflight Configurator
- Rotorflight Blackbox
- Lua Scripts for EdgeTx and OpenTx
- Lua Scripts for FrSky Ethos
- Lua Suite for FrSky Ethos
Notes
-
Rotorflight setup instructions can be found on the RF website www.rotorflight.org.
-
RF 2.1 is backward compatible with RF 2.0. You can load your configuration dump from RF 2.0 into 2.1.
-
If updating from RF1, please setup your helicopter from scratch. Follow the instructions on the website!
-
As always, please double check your configuration on the bench before flying!
Changes from 2.0.0
- Custom CRSF/ELRS telemetry support
- Add FBUS and F.Port2 receiver protocols
- Add SBUS Output to serial ports
- Add new SmartPort sensors
- Automatic board detection in Firmware Flasher
- Stay backwards compatible with RF 2.0
- Cyclic Cross-Coupling refactored
- Add ACC trim adjustments
- Add ESC log options to Blackbox
- Add support for SBUS2
- Add support for UART Tx/Rx Pinswap
- Add ESC telemetry half-duplex and pin-swap toggles
- Add support for Graupner and FlyRotor ESC telemetry
- Improved ctrl-mouse zoom
- Improved sidebar style
- Refactor bottom status bar
- Hide Rates acceleration and response (until fixed)
- Disable motor override when leaving the Motors tab
- Display final gear ratio with decimals
- Update slider implementation (nouislider)
- Update Reference design port allocations
- Update Bell 206 3D model with RF brand
- Update RPM filter Q range to 1.5-10.0
- Update default rates to match firmware
- Fix many spelling mistakes
- Add various tooltips
Changes from 2.1.0-RC1
- Add SBUS Output to serial ports
- FBUS and F.Port2 receiver protocols
- Cancel MSP request retry if serial has disconnected
- Restrict telemetry sensors to supported protocol
- Display final gear ratio with decimals
- Fix texture bleed on Bell 3D mode
- Wait for motor override disable before leaving motor page
- Fix CRSF custom telemetry toggle showing wrong state
- Translations updated
Rotorflight Configurator Release Candidate 2.1.0-RC1
This is the first Release Candidate of the Rotorflight 2.1 Configurator.
NOTE The final 2.1.0 Configurator will be released after a few release candidates. Please don't use RCs once the final release is out.
Downloads
The download locations are:
- Rotorflight Configurator
- Rotorflight Blackbox
- Lua Scripts for EdgeTx and OpenTx
- Lua Scripts for FrSky Ethos
- Lua Suite for FrSky Ethos
Notes
-
Rotorflight setup instructions can be found on the RF website www.rotorflight.org.
-
RF 2.1 is backward compatible with RF 2.0. You can load your configuration dump from RF 2.0 into 2.1.
-
If updating from RF1, please setup your helicopter from scratch. Follow the instructions on the website!
-
As always, please double check your configuration on the bench before flying!
Changes from 2.0.0
- Custom CRSF/ELRS telemetry support
- Add new SmartPort sensors
- Automatic board detection in Firmware Flasher
- Stay backwards compatible with RF 2.0
- Cyclic Cross-Coupling refactored
- Add ACC trim adjustments
- Add ESC log options to Blackbox
- Add support for SBUS2
- Add support for UART Tx/Rx Pinswap
- Add ESC telemetry half-duplex and pin-swap toggles
- Add support for Graupner and FlyRotor ESC telemetry
- Improved ctrl-mouse zoom
- Improved sidebar style
- Refactor bottom status bar
- Hide Rates acceleration and response (until fixed)
- Disable motor override when leaving the Motors tab
- Update slider implementation (nouislider)
- Update Reference design port allocations
- Update Bell 206 3D model with RF brand
- Update RPM filter Q range to 1.5-10.0
- Update default rates to match firmware
- Fix many spelling mistakes
- Add various tooltips
Changes from 2.1.0-20240929
- Update Bell 206 3D model with RF brand
- Update design port allocations
- Update RPM filter Q range to 1.5-10.0
- Update default rates to match firmware
- Add new SmartPort sensors
- Add support for Graupner and FlyRotor ESC telemetry
- Add various tooltips
- Disable motor override when leaving the Motors tab
- Fix many spelling mistakes
- Locales ready for translation
Rotorflight Configurator Snapshot 2.1.0-20240929
This is a development snapshot of the Rotorflight 2.1 Configurator.
Notes
This version is intended to be used for beta-testing only.
It is not fully working nor stable, and should not be used by end-users.
For more information, please join the Rotorflight Discord chat.
Downloads
The download locations are:
- Rotorflight Configurator
- Rotorflight Blackbox
- LUA Scripts for EdgeTx and OpenTx
- LUA Scripts for FrSky Ethos
Changes
- Improved sidebar style
- Add ESC telemetry half-duplex and pin-swap toggles
- Refactor bottom status bar
- Hide Rates acceleration and response (until fixed)
- Update nouislider
Rotorflight Configurator Snapshot 2.1.0-20240828
This is a development snapshot of the Rotorflight 2.1 Configurator.
Notes
This version is intended to be used for beta-testing only.
It is not fully working nor stable, and should not be used by end-users.
For more information, please join the Rotorflight Discord chat.
Downloads
The download locations are:
- Rotorflight Configurator
- Rotorflight Blackbox
- LUA Scripts for EdgeTx and OpenTx
- LUA Scripts for FrSky Ethos
Changes
- Backwards compatibility with RF 2.0
- Custom CRSF/ELRS telemetry support
- Automatic board detection in Firmware Flasher
- Cyclic Cross-Coupling cutoff scaling added
- Acc trim adjustments added
- ESC BB log options added
- SBUS2 protocol added
- Pinswap config added
- Improved ctrl-mouse zoom
- Accept 4.4.x firmware
Rotorflight Configurator Release 2.0.0
This is the first official Release of the Rotorflight-2 Configurator.
Downloads
The download locations for Rotorflight 2.0.0 are:
- Rotorflight Configurator
- Rotorflight Blackbox
- LUA Scripts for EdgeTx and OpenTx
- LUA Scripts for FrSky Ethos
Notes
-
There is a new website www.rotorflight.org for Rotorflight-2. The old Wiki in github is deprecated, and is for Rotorflight-1 only. Big thanks to the documentation team for setting this up!
-
Rotorflight-2 is NOT backward compatible with RF1. You MUST NOT load your configuration dump from RF1 into RF2.
-
If coming from RF1, please setup your helicopter from scratch for RF2. Follow the instructions on the website!
-
As always, please double check your configuration on the bench before flying!
Support
The main source of Rotorflight information and instructions is now the website.
Rotorflight has a strong presence on the Discord platform - you can join us here.
Discord is the primary location for support, questions and discussions. The developers are all active there,
and so are the manufacturers of RF Flight Controllers. Many pro pilots are also there.
This is a great place to ask for advice or discuss any complicated problems or even new ideas.
There is also a Rotorflight Facebook Group for hanging out with other Rotorflight pilots.
Changes
RF2 is built on Betaflight 4.3, and is rewritten from ground up, with the experience learned from Rotorflight-1.
Lots of things have changed in the two years of development. A full changelog can be found in
git.
Changes since 2.0.0-RC3
- Update translated locales
- Fix reset default values in Rates
Rotorflight Configurator Release Candidate 2.0.0-RC3
This is the third Release Candidate of the Rotorflight-2 Configurator.
Downloads
The official download locations for Rotorflight 2.0.0-RC3 are:
- Rotorflight Configurator
- Rotorflight Blackbox
- LUA Scripts for EdgeTx and OpenTx
- LUA Scripts for FrSky Ethos
Notes
-
There is a new website www.rotorflight.org for Rotorflight-2. The old Wiki in github is deprecated, and is for Rotorflight-1 only. Big thanks to the documentation team for setting this up!
-
Rotorflight-2 is NOT backward compatible with RF1. You MUST NOT load your configuration dump from RF1 into RF2.
-
If coming from RF1, please setup your helicopter from scratch for RF2. Follow the instructions on the website!
-
As always, please double check your configuration on the bench before flying!
Support
The main source of Rotorflight information and instructions is now the website.
Rotorflight has a strong presence on the Discord platform - you can join us here.
Discord is the primary location for support, questions and discussions. The developers are all active there,
and so are the manufacturers of RF Flight Controllers. Many pro pilots are also there.
This is a great place to ask for advice or discuss any complicated problems or even new ideas.
There is also a Rotorflight Facebook Group for hanging out with other Rotorflight pilots.
Changes
RF2 is built on Betaflight 4.3, and is rewritten from ground up, with the experience learned from Rotorflight-1.
Lots of things have changed in the two years of development. A full changelog can be found in
git.
Changes since 2.0.0-RC2
- Add cyclic decay parameters to Profiles
- Fix saving default Profile and Rates Profile
- Fix output throttle PWM limits
- Extend governor max throttle range to 0..100%
- Extend rescue rate limit to 1000
- Show PID gain help icons
- Disable unavailable telemetry protocols in ESC telemetry dropdown
- New Donate button that works also in China
- Update translated locales
Rotorflight Configurator Release Candidate 2.0.0-RC2
This is the second Release Candidate of the Rotorflight-2 Configurator.
Downloads
The official download locations for Rotorflight 2.0.0-RC2 are:
- Rotorflight Configurator
- Rotorflight Blackbox
- LUA Scripts for EdgeTx and OpenTx
- LUA Scripts for FrSky Ethos
Notes
-
There is a new website www.rotorflight.org for Rotorflight-2. The old Wiki in github is deprecated, and is for Rotorflight-1 only. Big thanks to the documentation team for setting this up!
-
Rotorflight-2 is NOT backward compatible with RF1. You MUST NOT load your configuration dump from RF1 into RF2.
-
If coming from RF1, please setup your helicopter from scratch for RF2. Follow the instructions on the website!
-
As always, please double check your configuration on the bench before flying!
Support
The main source of Rotorflight information and instructions is now the website.
Rotorflight has a strong presence on the Discord platform - you can join us here.
Discord is the primary location for support, questions and discussions. The developers are all active there,
and so are the manufacturers of RF Flight Controllers. Many pro pilots are also there.
This is a great place to ask for advice or discuss any complicated problems or even new ideas.
There is also a Rotorflight Facebook Group for hanging out with other Rotorflight pilots.
Changes
RF2 is built on Betaflight 4.3, and is rewritten from ground up, with the experience learned from Rotorflight-1.
Lots of things have changed in the two years of development. A full changelog can be found online later.
Changes since 2.0.0-RC1
- Accept all MSP compatible firmware
- Extend yaw Mixer override to -60°..60°
- Adjust RPM filter defaults
- Add GOV_MODE to FrSky telemetry sensors
- Fix top bar battery gadget to show battery info from the FC
- Update links to point to www.rotorflight.org
- Add a notice for Configurator development versions
- Update english messages
- Update translations (de,nl,fr)
- Hide untranslated locales
- Update startup page
- Add Donation info
- Hide builtin ChangeLog
- Update README.md and HOWTO.md
- Remove old NSIS installer
Rotorflight Configurator Release Candidate 2.0.0-RC1
Release Candidate
This is the first Release Candidate of the Rotorflight 2 Configurator.
Downloads
The official download locations for Rotorflight 2.0.0-RC1 are:
Notes
-
There is a new website www.rotorflight.org for Rotorflight 2.
The old Wiki in github is deprecated, and is for Rotorflight-1 only.
Big thanks to the documentation team for setting this up! -
Rotorflight 2 is NOT backward compatible with RF1. You MUST NOT load your configuration dump from RF1 into RF2.
-
If coming from RF1, please setup your helicopter from scratch for RF2. Follow the instructions on the website!
-
As always, please double check your configuration on the bench before flying!
Support
The main source of Rotorflight information and instructions is now the website.
Rotorflight has a strong presence on the Discord platform - you can join us here.
Discord is the primary location for support, questions and discussions. The developers are all active there,
and so are the manufacturers of RF Flight Controllers. Many pro pilots are also there.
This is a great place to ask for advice or discuss any complicated problems or even new ideas.
There is also a Rotorflight Facebook Group for hanging out with other Rotorflight pilots.
Changes
RF2 is based on Betaflight 4.3.x, and is rewritten from ground up, with the experience learned from Rotorflight-1.
Lots of things have changed in the two years of development. A full changelog can be found online later.
Changes since 2.0.0-20240218
- Fix Zoom function
- Relax servo rate limits
- Refactor MSP_SERVO_CONFIGURATIONS
- Change default channel order to AECR1T23
- Add vendor names in receiver protocols
- Many fixes in labels and help texts
- Update locales for translation
Rotorflight Configurator Snapshot 2.0.0-20240218
Snapshot Release
This version is a development snapshot, intended to be used only for beta-testing.
It is not fully working nor stable, and should not be used by end-users.
The Configurator is currently under development, so please expect
many things to be broken, and changing rapidly.
For more information, please join the Rotorflight Discord chat.
Changes from 2.0.0-20240128
- Add OpenYGE ESC protocol
- Add Battery Cell Count to Power tag
- Add Governor Precomp Bandwidth to Motors tab
- Relax servo parameter checks
- Increase max yaw to 60° in Mixer
- Improved code in Status page0
- Refactor MSP_BATTERY_CONFIG