Extend SPI2 feature guard for some stm32l0x1 devices

There are members of the stm32l0x1 subfamily that thave two SPIs.  In
particular the STM32l051 and the STM32l071.

Compile tested as:

cargo build --release --example spi2 --features mcu-STM32L051C8Tx
(builds)

cargo build --release --example spi2  --features mcu-STM32L031C6Tx
(fails to build, as this subfamily only has 1 SPI)

but not run on actual hardware.

examples/spi2.rs

@@ -0,0 +1,55 @@
+//! An example to show the configuration and usage of SPI1 and SPI2 on `stm32l0x2`, `stm32l0x3` and
+//! the subset of `stm32l0x1` series that have two SPI ports
+//!
+#![deny(unsafe_code)]
+#![no_main]
+#![no_std]
+
+extern crate panic_halt;
+
+use cortex_m_rt::entry;
+use stm32l0xx_hal::{pac, prelude::*, rcc::Config, spi};
+
+#[entry]
+fn main() -> ! {
+    let dp = pac::Peripherals::take().unwrap();
+
+    // Configure the clock.
+    let mut rcc = dp.RCC.freeze(Config::hsi16());
+
+    // Acquire the GPIOA peripheral. This also enables the clock for GPIOA in
+    // the RCC register.
+    let gpioa = dp.GPIOA.split(&mut rcc);
+
+    let mut nss = gpioa.pa4.into_push_pull_output();
+    let sck = gpioa.pa5;
+    let miso = gpioa.pa6;
+    let mosi = gpioa.pa7;
+
+    // Initialise the SPI1 peripheral.
+    let mut spi = dp
+        .SPI1
+        .spi((sck, miso, mosi), spi::MODE_0, 100_000.Hz(), &mut rcc);
+
+    let gpiob = dp.GPIOB.split(&mut rcc);
+
+    let mut nss2 = gpiob.pb12.into_push_pull_output();
+    let sck2 = gpiob.pb13;
+    let miso2 = gpiob.pb14;
+    let mosi2 = gpiob.pb15;
+
+    // Initialise the SPI2 peripheral.
+    let mut spi2 = dp
+        .SPI2
+        .spi((sck2, miso2, mosi2), spi::MODE_0, 100_000.Hz(), &mut rcc);
+
+    loop {
+        nss.set_low().unwrap();
+        spi.write(&[0, 1]).unwrap();
+        nss.set_high().unwrap();
+
+        nss2.set_low().unwrap();
+        spi2.write(&[0, 1]).unwrap();
+        nss2.set_high().unwrap();
+    }
+}

src/spi.rs

@@ -16,7 +16,12 @@ use crate::gpio::gpiob::*;
 use crate::gpio::{AltMode, Analog};
 use crate::hal;
 use crate::pac::SPI1;
-#[cfg(any(feature = "stm32l0x2", feature = "stm32l0x3"))]
+#[cfg(any(
+    feature = "io-STM32L051",
+    feature = "io-STM32L071",
+    feature = "stm32l0x2",
+    feature = "stm32l0x3"
+))]
 use crate::pac::SPI2;
 use crate::rcc::{Enable, Rcc};
 
@@ -131,7 +136,12 @@ pins! {
         ]
 }
 
-#[cfg(any(feature = "stm32l0x2", feature = "stm32l0x3"))]
+#[cfg(any(
+    feature = "io-STM32L051",
+    feature = "io-STM32L071",
+    feature = "stm32l0x2",
+    feature = "stm32l0x3"
+))]
 pins! {
     SPI2:
         SCK: [
@@ -435,7 +445,12 @@ spi! {
     SPI1: (spi1, apb2_clk),
 }
 
-#[cfg(any(feature = "stm32l0x2", feature = "stm32l0x3"))]
+#[cfg(any(
+    feature = "io-STM32L051",
+    feature = "io-STM32L071",
+    feature = "stm32l0x2",
+    feature = "stm32l0x3"
+))]
 spi! {
     SPI2: (spi2, apb1_clk),
 }