esphome-apc-ups

ESPHome component to monitor and control a APC UPS via RS232

Supported devices

• APC SU420INET (firmware 21.3.I)
• APC SUVS420I (firmware 42.L.I)
• APC SUA1000I (firmware 652.13.I)

Requirements

• ESPHome 2024.6.0 or higher.
• Generic ESP32/ESP8266 board

Schematics

                 RS232                     UART-TTL
┌───────────┐              ┌──────────┐                ┌─────────┐
│           │              │          │<----- RX ----->│         │
│           │<---- TX ---->│  RS232   │<----- TX ----->│ ESP32/  │
│  APC UPS  │<---- RX ---->│  to TTL  │<----- GND ---->│ ESP8266 │
│           │<---- GND --->│  module  │<-- 3.3V VCC -->│         │<--- VCC
│           │              │          │                │         │<--- GND
└───────────┘              └──────────┘                └─────────┘

D-SUB 9P connector

Pin	Purpose	MAX3232 pin
1	RX	P14 (DOUT1)
2	TX	P13 (RIN1)
3
4
5
6
7
8
9	GND	P15 (GND)

MAX3232

Pin	Label	ESPHome	ESP8266 example	ESP32 example
P11 (DIN1)	TXD	tx_pin	GPIO4	GPIO16
P12 (ROUT1)	RXD	rx_pin	GPIO5	GPIO17
P16 (VCC)	VCC
P15 (GND)	GND

Installation

You can install this component with ESPHome external components feature like this:

external_components:
  - source: github://syssi/esphome-apc-ups@main

or just use the esp32-example.yaml as proof of concept:

# Install esphome
pip3 install esphome

# Clone this external component
git clone https://github.com/syssi/esphome-apc-ups.git
cd esphome-apc-ups

# Create a secrets.yaml containing some setup specific secrets
cat > secrets.yaml <<EOF
wifi_ssid: MY_WIFI_SSID
wifi_password: MY_WIFI_PASSWORD

mqtt_host: MY_MQTT_HOST
mqtt_username: MY_MQTT_USERNAME
mqtt_password: MY_MQTT_PASSWORD
EOF

# Validate the configuration, create a binary, upload it, and start logs
# If you use a esp8266 run the esp8266-examle.yaml
esphome run esp32-example.yaml

Example response all sensors enabled

[apc_ups:286]: Sending polling command : Y with length 1
[apc_ups:112]: Decode Y
[apc_ups:286]: Sending polling command : Q with length 1
[apc_ups:153]: Decode Q
[sensor:094]: 'apc-ups status bitmask': Sending state 8.00000  with 0 decimals of accuracy
[binary_sensor:036]: 'apc-ups runtime calibration': Sending state OFF
[binary_sensor:036]: 'apc-ups smart trim': Sending state OFF
[binary_sensor:036]: 'apc-ups smart boost': Sending state OFF
[binary_sensor:036]: 'apc-ups on line': Sending state ON
[binary_sensor:036]: 'apc-ups on battery': Sending state OFF
[binary_sensor:036]: 'apc-ups output overloaded': Sending state OFF
[binary_sensor:036]: 'apc-ups battery low': Sending state OFF
[binary_sensor:036]: 'apc-ups replace battery': Sending state OFF
[apc_ups:286]: Sending polling command : B with length 1
[apc_ups:117]: Decode B
[sensor:094]: 'apc-ups battery voltage': Sending state 13.61000 V with 2 decimals of accuracy
[apc_ups:286]: Sending polling command : F with length 1
[apc_ups:123]: Decode F
[sensor:094]: 'apc-ups grid frequency': Sending state 50.00000 Hz with 2 decimals of accuracy
[apc_ups:286]: Sending polling command : L with length 1
[apc_ups:135]: Decode L
[sensor:094]: 'apc-ups grid voltage': Sending state 231.80000 V with 1 decimals of accuracy
[apc_ups:286]: Sending polling command : O with length 1
[apc_ups:141]: Decode O
[sensor:094]: 'apc-ups ac output voltage': Sending state 231.80000 V with 1 decimals of accuracy
[apc_ups:286]: Sending polling command : P with length 1
[apc_ups:147]: Decode P
[sensor:094]: 'apc-ups ac output load': Sending state 9.10000 % with 1 decimals of accuracy
[apc_ups:286]: Sending polling command : f with length 1
[apc_ups:171]: Decode f
[sensor:094]: 'apc-ups state of charge': Sending state 100.00000 % with 1 decimals of accuracy
[apc_ups:286]: Sending polling command : j with length 1
[apc_ups:177]: Decode j
[sensor:094]: 'apc-ups estimated runtime': Sending state 42.00000 min with 0 decimals of accuracy
[apc_ups:286]: Sending polling command : G with length 1
[apc_ups:129]: Decode G
[text_sensor:064]: 'apc-ups cause of last transfer': Sending state 'S'

Protocol

See kirbah.github.io/apc-ups/.

Known issues

None.

Debugging

If this component doesn't work out of the box for your device please update your configuration to increase the log level to see details about the UART traffic:

logger:
  level: DEBUG

uart:
  - id: uart_0
    baud_rate: 2400
    tx_pin: ${tx_pin}
    rx_pin: ${rx_pin}
    debug:
      direction: BOTH
      dummy_receiver: false
      after:
        delimiter: "\r"
      sequence:
        - lambda: UARTDebug::log_string(direction, bytes);

References

• https://github.com/kirbah/apc-ups
• http://www.apcupsd.org/manual/#apc-smart-protocol
• https://github.com/ssieb/custom_components/tree/master/components/apcups