Skip to content

Atmega 32u4 based USB HID controller for ViperCore's FCC3 Force sensing mod for TM warthog/Cougar

License

Notifications You must be signed in to change notification settings

uriba107/fcc_controller

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

34 Commits
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

FCC3 controller board

This Arduino Based project, is meant to allow FCC3 force sensing mod for Cougar, to be used with Thrustmaster Warthog without the need to use the old TM Cougar Electronics

This software is distributed under MIT license, and is provided as is and without any warranty what so ever. Further information can be found in "license.txt" which belongs to the LUFA framework on which controller code is based.

Table Of Content

Features

  • 11 bit output on Pitch and Roll.
  • Support for both Cougar and Warthog grips.
  • On the fly configuration changes:
    • Multiple force presets (9, 6 & 4.5 Kg/f), in addition to one user configurable sensitivity setting.
    • User toggleable, FLCS Based, realistic force ratios.
    • User toggleable FLCS sensor rotation. In later blocks, the stick sensor is rotated clockwise to reduce accidental roll on pitch commands. Activating this option will simulate that.
    • on the fly re-centering (just in case).
  • Bi-Directional Control software:
    • Allows Joystick settings change (same as available via the grip).
    • Allows User configurable sensitivity setting to be set.
    • Handles Firmware upgrades for the stick.

Note:
The code was developed with the help of ViperCore, makers of the FCC3. They have also produce a compatible board which can be purchsed either as a Standalone board or bundled with FCW1 module

What settings are recommended

FLCS and SSC config had changed over the years, so depending on what type of F-16 you want to model, settings will vary.

Blocks 30/32 and before:

  • Analog FLCS
  • Sensor Rotation - Disabled

Block 40/42 and after:

  • Digital FLCS
  • Sensor Rotation - Enabled

FLCS in F-16

There are two types of FLCS installed in F-16s.The controller attempts to emulate both system operational logic.

In both cases, force ratio is maintained by the controller. The selected force setting is used as full pitch up command (which is the maximum required force), while pitch down and roll are proportional according to the FLCS version emulated.

Analog FLCS

Real life:
Full pitch up command is 180N (about 18Kgf), while full pitch down and full roll are 80N (or about 8Kgf).

Controller example: in 9Kg/f mode, full pitch up will be 9kg/f for full deflection, but on the other axis, only 4kg/f will be required.

Digital FLCS

Real life:
full pitch up command is 25lbf, while full pitch down is 16lbf and full roll is 17lbf.

Controller example:
In 9kgf mode, Pitch up command will be 9kgf for full deflection. full pitch down will require 5.76kgf and full roll will require 6.12kgf.

Cheat sheet

Image of fcc_controller button layout

BOM

  • Atmega 32U4 based board (Arduino pro-micro or an Arduino Micro are recommended)
  • MCP3202 - 12 Bit external ADC
  • A small protoboard (cheap dual sided 4*6 will be good enough)
  • For Pro-micro - A momentary push button and 10+ Kohm resistor as the board has no reset switch.
  • A few LEDs and resistors - for status.
  • Header pins, two 3 pin headers and one 5 pins header, for grip and analog sensors. Generic 0.1" headers will do the trick. But correct header will be the JST EH series connectors.
  • Female Headers for the Arduino (optional)
  • DIP8 socket for the MCP3202 (optional)

About

Atmega 32u4 based USB HID controller for ViperCore's FCC3 Force sensing mod for TM warthog/Cougar

Resources

License

Stars

Watchers

Forks

Packages

No packages published