-
Notifications
You must be signed in to change notification settings - Fork 5
SDM : Protocol Description
Oleksiy Kebkal edited this page Mar 27, 2024
·
3 revisions
default socket: IP:4200
SDM Frame Format
<0x80,0x00,0x7f,0xff,0x00,0x00,0x00,0x00>
,<cmd:8>,<param:24>,<len:32>,<data:len*16>all numbers are little-endian.
| cmd | code | param | len | description |
| STOP | 0 | 0 | 0 | - ongoing TX: stop transmitting until FPGBUSY EDGE - ongoing RX: stop receiving until FPGABUSY EDGE - otherwise: send SDM_CMD_STOP command |
| TX | 1 | 0 | > 0 | - ongoing TX: return BUSY,TX and stop ongoing data transmission until FPGABUSY EDGE - ongoing RX: return BUSY,RX and stop ongoing data reception until FPGABUSY EDGE - otherwise: transmission of len 16-bit samples, transmission begins immediately (TX_ON and SDM_CMD_TX) - len must be divisible by 1024, otherwise undefined behaviour |
| RX | 2 | len: >= 0 | 0 | - ongoing TX: return BUSY,TX and stop ongoing data transmission until FPGABUSY EDGE - ongoing RX: redefine param and continue to do RX - otherwise: send SDM_CMD_RX command - param len: length of 16-bit samples want to be received - if len equal 0 then 16-bit samples will be received till comman SDM_CMD_STOP |
| REF | 3 | 0 | `>` 0 | - ongoing TX or RX: return BUSY and stop ongoing process until FPGABUSY EDGE - otherwise: send SDM_CMD_REF |
| CONFIG | 4 | - thr:16 - gain:1 - srclevel:7 |
0/1 | If len == 1, data contains preamplifier gain: preamp_gain:4,reserved:12 Preamplifier gain is described in the table below If thr == 0, RX bypasses threshold and starts RX immediately Example: by thr:350, gain: 1, source level: 2, param value is 0x5e,0x01,0x82 |
| USBL_CONFIG | 5 | - preamp_gain:4 - sample_rate:3 - reserved:17 |
4 | - write_delay:32 in samples, 65535 max - data_length:32 in samples, 1024,2048…51200 |
| USBL_RX | 6 | - data_len:16 - channel:3 - reserved:5 |
0 | |
| SYSTIME | 7 | 0 | 0 | requests current dsp clock value, last tx time, last rx time in us |
USBL_CONFIG, USBL_RX, SYSTIME since dsp version 0x40da
| cmd | code | param | len | description |
| STOP | 0 | 0 | 0 | report about STOP higher level |
| RX | 2 | 0 | >= 0 | start data reception, prepare RX frame header, len contains predefined by higher layer parameter |
| USBL_RX | 6 | 0 | >= 0 | start USBL data reception, prepare RX frame header, len contains predefined by higher layer parameter |
| SYSTIME | 7 | 0 | 6 | current_time:32/unsigned-little-endian, tx_time:32/unsigned-little-endian, rx_time:32/unsigned-little-endian |
| SYSTIME | 7 | 0 | 8 | current_time:32/unsigned-little-endian, tx_time:32/unsigned-little-endian, rx_time:32/unsigned-little-endian, sync_in_time:32/unsigned-little-endian |
SYNCIN and sync_in_time from dsp version 0x40dc
time in microseconds
NOTE: by switching to PHY STOP is generated.
| cmd | cmd code | param | len | description |
| SYNCIN | 253 | 0 | 0 | sync in event (clock can be requested with SYSTIME) |
| BUSY | 254 | 1 or 2 | 0 | in case of race conditions |
| REPORT | 255 | 0 | 0 | stop rejected (not in SDM mode) |
| 1 | len | transmission stopped after len samples (FPGABUSY EDGE) | ||
| 2 | len | reception stopped after len samples (FPGABUSY EDGE) | ||
| 3 | 0 | reference update failed | ||
| 3 | len | reference update finished | ||
| 4 | 0 | config failed | ||
| 4 | 1 | config accepted | ||
| 5 | 0 | usbl config failed | ||
| 5 | 1 | usbl config accepted | ||
| 6 | len | usbl reception stopped after len samples (FPGABUSY EDGE) | ||
| 7 | 0 | system time request failed | ||
| 254 | len | garbage dropped | ||
| 255 | code | unknown command code |
SYNCIN and sync_in_time from dsp version 0x40dc