Openbmc/wdt #5

jk-ozlabs · 2015-10-22T08:54:46Z

No description provided.

Signed-off-by: Jeremy Kerr <jk@ozlabs.org>

We do the same reset procedure in apeed_wdt_enable and our reboot notifier, so move these to a separate function. Also, use a couple of definitions for the watchdog control value rather than a hardcoded '3'. Signed-off-by: Jeremy Kerr <jk@ozlabs.org>

Currently, the watchdog timer does nothing on expiry - the 'SoC system' reset type doesn't seem to have any effect. This change uses the 'full chip' reset type instead. Signed-off-by: Jeremy Kerr <jk@ozlabs.org>

shenki · 2015-10-23T04:35:04Z

Still a bit concerned that we don't understand why we need the full chip reset, but happy to merge it as it makes the system much easier to use.

Merged.

…ap_device_late_init Kernel fails to boot 50% of times (form build to build) with RT-patchset applied due to the following race - on late boot stages deferred_probe_work_func->omap_hsmmc_probe races with omap_device_late_ini. The same issue has been reported now on linux-next (4.3) by Keerthy [1] late_initcall - deferred_probe_initcal() tries to re-probe all pending driver's probe. - later on, some driver is probing in this case It's cpsw.c (but could be any other drivers) cpsw_init - platform_driver_register - really_probe - driver_bound - driver_deferred_probe_trigger and boot proceed. So, at this moment we have deferred_probe_work_func scheduled. late_initcall_sync - omap_device_late_init - omap_device_idle CPU1 CPU2 - deferred_probe_work_func - really_probe - omap_hsmmc_probe - pm_runtime_get_sync late_initcall_sync - omap_device_late_init if (od->_driver_status != BUS_NOTIFY_BOUND_DRIVER) { if (od->_state == OMAP_DEVICE_STATE_ENABLED) { - omap_device_idle [ops - IP is disabled] - [fail] - pm_runtime_put_sync - omap_hsmmc_runtime_suspend [ooops!] == log == omap_hsmmc 480b4000.mmc: unable to get vmmc regulator -517 davinci_mdio 48485000.mdio: davinci mdio revision 1.6 davinci_mdio 48485000.mdio: detected phy mask fffffff3 libphy: 48485000.mdio: probed davinci_mdio 48485000.mdio: phy[2]: device 48485000.mdio:02, driver unknown davinci_mdio 48485000.mdio: phy[3]: device 48485000.mdio:03, driver unknown omap_hsmmc 480b4000.mmc: unable to get vmmc regulator -517 cpsw 48484000.ethernet: Detected MACID = b4:99:4c:c7:d2:48 cpsw 48484000.ethernet: cpsw: Detected MACID = b4:99:4c:c7:d2:49 hctosys: unable to open rtc device (rtc0) omap_hsmmc 480b4000.mmc: omap_device_late_idle: enabled but no driver. Idling ldousb: disabling Unhandled fault: imprecise external abort (0x1406) at 0x00000000 [00000000] *pgd=00000000 Internal error: : 1406 [#1] PREEMPT SMP ARM Modules linked in: CPU: 1 PID: 58 Comm: kworker/u4:1 Not tainted 4.1.2-rt1-00467-g6da3c0a-dirty #5 Hardware name: Generic DRA74X (Flattened Device Tree) Workqueue: deferwq deferred_probe_work_func task: ee6ddb00 ti: edd3c000 task.ti: edd3c000 PC is at omap_hsmmc_runtime_suspend+0x1c/0x12c LR is at _od_runtime_suspend+0xc/0x24 pc : [<c0471998>] lr : [<c0029590>] psr: a0000013 sp : edd3dda0 ip : ee6ddb00 fp : c07be540 r10: 00000000 r9 : c07be540 r8 : 00000008 r7 : 00000000 r6 : ee646c10 r5 : ee646c10 r4 : edd79380 r3 : fa0b4100 r2 : 00000000 r1 : 00000000 r0 : ee646c10 Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel Control: 10c5387d Table: 8000406a DAC: 00000015 Process kworker/u4:1 (pid: 58, stack limit = 0xedd3c218) Stack: (0xedd3dda0 to 0xedd3e000) dda0: ee646c70 ee646c10 c0029584 00000000 00000008 c0029590 ee646c70 ee646c10 ddc0: c0029584 c03adfb8 ee646c10 00000004 0000000c c03adff0 ee646c10 00000004 dde0: 0000000c c03ae4ec 00000000 edd3c000 ee646c10 00000004 ee646c70 00000004 de00: fa0b4000 c03aec20 ee6ddb00 ee646c10 00000004 ee646c70 ee646c10 fffffdfb de20: edd79380 00000000 fa0b4000 c03aee90 fffffdfb edd79000 ee646c00 c0474290 de40: 00000000 edda24c0 edd79380 edc81f00 00000000 00000200 00000001 c06dd488 de60: edda3960 ee646c10 ee646c10 c0824cc4 fffffdfb c0880c94 00000002 edc92600 de80: c0836378 c03a7f84 ee646c10 c0824cc4 00000000 c0880c80 c0880c94 c03a6568 dea0: 00000000 ee646c10 c03a66ac ee4f8000 00000000 00000001 edc92600 c03a4b40 dec0: ee404c94 edc83c4c ee646c10 ee646c10 ee646c44 c03a63c4 ee646c10 ee646c10 dee0: c0814448 c03a5aa8 ee646c10 c0814220 edd3c000 c03a5ec0 c0814250 ee6be400 df00: edd3c000 c004e5bc ee6ddb01 00000078 ee6ddb00 ee4f8000 ee6be418 edd3c000 df20: ee4f8028 00000088 c0836045 ee4f8000 ee6be400 c004e928 ee4f8028 00000000 df40: c004e8ec 00000000 ee6bf1c0 ee6be400 c004e8ec 00000000 00000000 00000000 df60: 00000000 c0053450 2e56fa97 00000000 afdffbd7 ee6be400 00000000 00000000 df80: edd3df80 edd3df80 00000000 00000000 edd3df90 edd3df90 edd3dfac ee6bf1c0 dfa0: c0053384 00000000 00000000 c000f668 00000000 00000000 00000000 00000000 dfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 dfe0: 00000000 00000000 00000000 00000000 00000013 00000000 f1fc9d7e febfbdff [<c0471998>] (omap_hsmmc_runtime_suspend) from [<c0029590>] (_od_runtime_suspend+0xc/0x24) [<c0029590>] (_od_runtime_suspend) from [<c03adfb8>] (__rpm_callback+0x24/0x3c) [<c03adfb8>] (__rpm_callback) from [<c03adff0>] (rpm_callback+0x20/0x80) [<c03adff0>] (rpm_callback) from [<c03ae4ec>] (rpm_suspend+0xe4/0x618) [<c03ae4ec>] (rpm_suspend) from [<c03aee90>] (__pm_runtime_idle+0x60/0x80) [<c03aee90>] (__pm_runtime_idle) from [<c0474290>] (omap_hsmmc_probe+0x6bc/0xa7c) [<c0474290>] (omap_hsmmc_probe) from [<c03a7f84>] (platform_drv_probe+0x44/0xa4) [<c03a7f84>] (platform_drv_probe) from [<c03a6568>] (driver_probe_device+0x170/0x2b4) [<c03a6568>] (driver_probe_device) from [<c03a4b40>] (bus_for_each_drv+0x64/0x98) [<c03a4b40>] (bus_for_each_drv) from [<c03a63c4>] (device_attach+0x70/0x88) [<c03a63c4>] (device_attach) from [<c03a5aa8>] (bus_probe_device+0x84/0xac) [<c03a5aa8>] (bus_probe_device) from [<c03a5ec0>] (deferred_probe_work_func+0x58/0x88) [<c03a5ec0>] (deferred_probe_work_func) from [<c004e5bc>] (process_one_work+0x134/0x464) [<c004e5bc>] (process_one_work) from [<c004e928>] (worker_thread+0x3c/0x4fc) [<c004e928>] (worker_thread) from [<c0053450>] (kthread+0xcc/0xe4) [<c0053450>] (kthread) from [<c000f668>] (ret_from_fork+0x14/0x2c) Code: e594302c e593202c e584205c e594302c (e5932128) ---[ end trace 0000000000000002 ]--- The issue happens because omap_device_late_init() do not take into account that some drivers are present, but their probes were not finished successfully and where deferred instead. This is the valid case, and omap_device_late_init() should not idle such devices. To fix this issue, the value of omap_device->_driver_status field should be checked not only for BUS_NOTIFY_BOUND_DRIVER (driver is present and has been bound to device successfully), but also checked for BUS_NOTIFY_BIND_DRIVER (driver about to be bound) - which means driver is present and there was try to bind it to device. [1] http://www.spinics.net/lists/arm-kernel/msg441880.html Cc: Tero Kristo <t-kristo@ti.com> Cc: Keerthy <j-keerthy@ti.com> Tested-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>

The renesas-irqc interrupt controller is cascaded to the GIC. Hence when propagating wake-up settings to its parent interrupt controller, the following lockdep warning is printed: ============================================= [ INFO: possible recursive locking detected ] 4.2.0-ape6evm-10725-g50fcd7643c034198 torvalds#280 Not tainted --------------------------------------------- s2ram/1072 is trying to acquire lock: (&irq_desc_lock_class){-.-...}, at: [<c008d3fc>] __irq_get_desc_lock+0x58/0x98 but task is already holding lock: (&irq_desc_lock_class){-.-...}, at: [<c008d3fc>] __irq_get_desc_lock+0x58/0x98 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&irq_desc_lock_class); lock(&irq_desc_lock_class); *** DEADLOCK *** May be due to missing lock nesting notation 6 locks held by s2ram/1072: #0: (sb_writers#7){.+.+.+}, at: [<c012eb14>] __sb_start_write+0xa0/0xa8 #1: (&of->mutex){+.+.+.}, at: [<c019396c>] kernfs_fop_write+0x4c/0x1bc #2: (s_active#24){.+.+.+}, at: [<c0193974>] kernfs_fop_write+0x54/0x1bc #3: (pm_mutex){+.+.+.}, at: [<c008213c>] pm_suspend+0x10c/0x510 #4: (&dev->mutex){......}, at: [<c02af3c4>] __device_suspend+0xdc/0x2cc #5: (&irq_desc_lock_class){-.-...}, at: [<c008d3fc>] __irq_get_desc_lock+0x58/0x98 stack backtrace: CPU: 0 PID: 1072 Comm: s2ram Not tainted 4.2.0-ape6evm-10725-g50fcd7643c034198 torvalds#280 Hardware name: Generic R8A73A4 (Flattened Device Tree) [<c0018078>] (unwind_backtrace) from [<c00144f0>] (show_stack+0x10/0x14) [<c00144f0>] (show_stack) from [<c0451f14>] (dump_stack+0x88/0x98) [<c0451f14>] (dump_stack) from [<c007b29c>] (__lock_acquire+0x15cc/0x20e4) [<c007b29c>] (__lock_acquire) from [<c007c6e0>] (lock_acquire+0xac/0x12c) [<c007c6e0>] (lock_acquire) from [<c0457c00>] (_raw_spin_lock_irqsave+0x40/0x54) [<c0457c00>] (_raw_spin_lock_irqsave) from [<c008d3fc>] (__irq_get_desc_lock+0x58/0x98) [<c008d3fc>] (__irq_get_desc_lock) from [<c008ebbc>] (irq_set_irq_wake+0x20/0xf8) [<c008ebbc>] (irq_set_irq_wake) from [<c0260770>] (irqc_irq_set_wake+0x20/0x4c) [<c0260770>] (irqc_irq_set_wake) from [<c008ec28>] (irq_set_irq_wake+0x8c/0xf8) [<c008ec28>] (irq_set_irq_wake) from [<c02cb8c0>] (gpio_keys_suspend+0x74/0xc0) [<c02cb8c0>] (gpio_keys_suspend) from [<c02ae8cc>] (dpm_run_callback+0x54/0x124) Avoid this false positive by using a separate lockdep class for IRQC interrupts. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Cc: Grygorii Strashko <grygorii.strashko@ti.com> Cc: Magnus Damm <magnus.damm@gmail.com> Cc: Jason Cooper <jason@lakedaemon.net> Link: http://lkml.kernel.org/r/1441798974-25716-2-git-send-email-geert%2Brenesas@glider.be Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

The renesas-intc-irqpin interrupt controller is cascaded to the GIC. Hence when propagating wake-up settings to its parent interrupt controller, the following lockdep warning is printed: ============================================= [ INFO: possible recursive locking detected ] 4.2.0-armadillo-10725-g50fcd7643c034198 torvalds#781 Not tainted --------------------------------------------- s2ram/1179 is trying to acquire lock: (&irq_desc_lock_class){-.-...}, at: [<c005bb54>] __irq_get_desc_lock+0x78/0x94 but task is already holding lock: (&irq_desc_lock_class){-.-...}, at: [<c005bb54>] __irq_get_desc_lock+0x78/0x94 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&irq_desc_lock_class); lock(&irq_desc_lock_class); *** DEADLOCK *** May be due to missing lock nesting notation 7 locks held by s2ram/1179: #0: (sb_writers#7){.+.+.+}, at: [<c00c9708>] __sb_start_write+0x64/0xb8 #1: (&of->mutex){+.+.+.}, at: [<c0125a00>] kernfs_fop_write+0x78/0x1a0 #2: (s_active#23){.+.+.+}, at: [<c0125a08>] kernfs_fop_write+0x80/0x1a0 #3: (autosleep_lock){+.+.+.}, at: [<c0058244>] pm_autosleep_lock+0x18/0x20 #4: (pm_mutex){+.+.+.}, at: [<c0057e50>] pm_suspend+0x54/0x248 #5: (&dev->mutex){......}, at: [<c0243a20>] __device_suspend+0xdc/0x240 #6: (&irq_desc_lock_class){-.-...}, at: [<c005bb54>] __irq_get_desc_lock+0x78/0x94 stack backtrace: CPU: 0 PID: 1179 Comm: s2ram Not tainted 4.2.0-armadillo-10725-g50fcd7643c034198 Hardware name: Generic R8A7740 (Flattened Device Tree) [<c00129f4>] (dump_backtrace) from [<c0012bec>] (show_stack+0x18/0x1c) [<c0012bd4>] (show_stack) from [<c03f5d94>] (dump_stack+0x20/0x28) [<c03f5d74>] (dump_stack) from [<c00514d4>] (__lock_acquire+0x67c/0x1b88) [<c0050e58>] (__lock_acquire) from [<c0052df8>] (lock_acquire+0x9c/0xbc) [<c0052d5c>] (lock_acquire) from [<c03fb068>] (_raw_spin_lock_irqsave+0x44/0x58) [<c03fb024>] (_raw_spin_lock_irqsave) from [<c005bb54>] (__irq_get_desc_lock+0x78/0x94 [<c005badc>] (__irq_get_desc_lock) from [<c005c3d8>] (irq_set_irq_wake+0x28/0x100) [<c005c3b0>] (irq_set_irq_wake) from [<c01e50d0>] (intc_irqpin_irq_set_wake+0x24/0x4c) [<c01e50ac>] (intc_irqpin_irq_set_wake) from [<c005c17c>] (set_irq_wake_real+0x3c/0x50 [<c005c140>] (set_irq_wake_real) from [<c005c414>] (irq_set_irq_wake+0x64/0x100) [<c005c3b0>] (irq_set_irq_wake) from [<c02a19b4>] (gpio_keys_suspend+0x60/0xa0) [<c02a1954>] (gpio_keys_suspend) from [<c023b750>] (platform_pm_suspend+0x3c/0x5c) Avoid this false positive by using a separate lockdep class for INTC External IRQ Pin interrupts. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Cc: Grygorii Strashko <grygorii.strashko@ti.com> Cc: Magnus Damm <magnus.damm@gmail.com> Cc: Jason Cooper <jason@lakedaemon.net> Link: http://lkml.kernel.org/r/1441798974-25716-3-git-send-email-geert%2Brenesas@glider.be Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

My colleague ran into a program stall on a x86_64 server, where n_tty_read() was waiting for data even if there was data in the buffer in the pty. kernel stack for the stuck process looks like below. #0 [ffff88303d107b58] __schedule at ffffffff815c4b20 #1 [ffff88303d107bd0] schedule at ffffffff815c513e #2 [ffff88303d107bf0] schedule_timeout at ffffffff815c7818 #3 [ffff88303d107ca0] wait_woken at ffffffff81096bd2 #4 [ffff88303d107ce0] n_tty_read at ffffffff8136fa23 #5 [ffff88303d107dd0] tty_read at ffffffff81368013 #6 [ffff88303d107e20] __vfs_read at ffffffff811a3704 #7 [ffff88303d107ec0] vfs_read at ffffffff811a3a57 #8 [ffff88303d107f00] sys_read at ffffffff811a4306 #9 [ffff88303d107f50] entry_SYSCALL_64_fastpath at ffffffff815c86d7 There seems to be two problems causing this issue. First, in drivers/tty/n_tty.c, __receive_buf() stores the data and updates ldata->commit_head using smp_store_release() and then checks the wait queue using waitqueue_active(). However, since there is no memory barrier, __receive_buf() could return without calling wake_up_interactive_poll(), and at the same time, n_tty_read() could start to wait in wait_woken() as in the following chart. __receive_buf() n_tty_read() ------------------------------------------------------------------------ if (waitqueue_active(&tty->read_wait)) /* Memory operations issued after the RELEASE may be completed before the RELEASE operation has completed */ add_wait_queue(&tty->read_wait, &wait); ... if (!input_available_p(tty, 0)) { smp_store_release(&ldata->commit_head, ldata->read_head); ... timeout = wait_woken(&wait, TASK_INTERRUPTIBLE, timeout); ------------------------------------------------------------------------ The second problem is that n_tty_read() also lacks a memory barrier call and could also cause __receive_buf() to return without calling wake_up_interactive_poll(), and n_tty_read() to wait in wait_woken() as in the chart below. __receive_buf() n_tty_read() ------------------------------------------------------------------------ spin_lock_irqsave(&q->lock, flags); /* from add_wait_queue() */ ... if (!input_available_p(tty, 0)) { /* Memory operations issued after the RELEASE may be completed before the RELEASE operation has completed */ smp_store_release(&ldata->commit_head, ldata->read_head); if (waitqueue_active(&tty->read_wait)) __add_wait_queue(q, wait); spin_unlock_irqrestore(&q->lock,flags); /* from add_wait_queue() */ ... timeout = wait_woken(&wait, TASK_INTERRUPTIBLE, timeout); ------------------------------------------------------------------------ There are also other places in drivers/tty/n_tty.c which have similar calls to waitqueue_active(), so instead of adding many memory barrier calls, this patch simply removes the call to waitqueue_active(), leaving just wake_up*() behind. This fixes both problems because, even though the memory access before or after the spinlocks in both wake_up*() and add_wait_queue() can sneak into the critical section, it cannot go past it and the critical section assures that they will be serialized (please see "INTER-CPU ACQUIRING BARRIER EFFECTS" in Documentation/memory-barriers.txt for a better explanation). Moreover, the resulting code is much simpler. Latency measurement using a ping-pong test over a pty doesn't show any visible performance drop. Signed-off-by: Kosuke Tatsukawa <tatsu@ab.jp.nec.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

…ap_device_late_init Kernel fails to boot 50% of times (form build to build) with RT-patchset applied due to the following race - on late boot stages deferred_probe_work_func->omap_hsmmc_probe races with omap_device_late_ini. The same issue has been reported now on linux-next (4.3) by Keerthy [1] late_initcall - deferred_probe_initcal() tries to re-probe all pending driver's probe. - later on, some driver is probing in this case It's cpsw.c (but could be any other drivers) cpsw_init - platform_driver_register - really_probe - driver_bound - driver_deferred_probe_trigger and boot proceed. So, at this moment we have deferred_probe_work_func scheduled. late_initcall_sync - omap_device_late_init - omap_device_idle CPU1 CPU2 - deferred_probe_work_func - really_probe - omap_hsmmc_probe - pm_runtime_get_sync late_initcall_sync - omap_device_late_init if (od->_driver_status != BUS_NOTIFY_BOUND_DRIVER) { if (od->_state == OMAP_DEVICE_STATE_ENABLED) { - omap_device_idle [ops - IP is disabled] - [fail] - pm_runtime_put_sync - omap_hsmmc_runtime_suspend [ooops!] == log == omap_hsmmc 480b4000.mmc: unable to get vmmc regulator -517 davinci_mdio 48485000.mdio: davinci mdio revision 1.6 davinci_mdio 48485000.mdio: detected phy mask fffffff3 libphy: 48485000.mdio: probed davinci_mdio 48485000.mdio: phy[2]: device 48485000.mdio:02, driver unknown davinci_mdio 48485000.mdio: phy[3]: device 48485000.mdio:03, driver unknown omap_hsmmc 480b4000.mmc: unable to get vmmc regulator -517 cpsw 48484000.ethernet: Detected MACID = b4:99:4c:c7:d2:48 cpsw 48484000.ethernet: cpsw: Detected MACID = b4:99:4c:c7:d2:49 hctosys: unable to open rtc device (rtc0) omap_hsmmc 480b4000.mmc: omap_device_late_idle: enabled but no driver. Idling ldousb: disabling Unhandled fault: imprecise external abort (0x1406) at 0x00000000 [00000000] *pgd=00000000 Internal error: : 1406 [openbmc#1] PREEMPT SMP ARM Modules linked in: CPU: 1 PID: 58 Comm: kworker/u4:1 Not tainted 4.1.2-rt1-00467-g6da3c0a-dirty openbmc#5 Hardware name: Generic DRA74X (Flattened Device Tree) Workqueue: deferwq deferred_probe_work_func task: ee6ddb00 ti: edd3c000 task.ti: edd3c000 PC is at omap_hsmmc_runtime_suspend+0x1c/0x12c LR is at _od_runtime_suspend+0xc/0x24 pc : [<c0471998>] lr : [<c0029590>] psr: a0000013 sp : edd3dda0 ip : ee6ddb00 fp : c07be540 r10: 00000000 r9 : c07be540 r8 : 00000008 r7 : 00000000 r6 : ee646c10 r5 : ee646c10 r4 : edd79380 r3 : fa0b4100 r2 : 00000000 r1 : 00000000 r0 : ee646c10 Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel Control: 10c5387d Table: 8000406a DAC: 00000015 Process kworker/u4:1 (pid: 58, stack limit = 0xedd3c218) Stack: (0xedd3dda0 to 0xedd3e000) dda0: ee646c70 ee646c10 c0029584 00000000 00000008 c0029590 ee646c70 ee646c10 ddc0: c0029584 c03adfb8 ee646c10 00000004 0000000c c03adff0 ee646c10 00000004 dde0: 0000000c c03ae4ec 00000000 edd3c000 ee646c10 00000004 ee646c70 00000004 de00: fa0b4000 c03aec20 ee6ddb00 ee646c10 00000004 ee646c70 ee646c10 fffffdfb de20: edd79380 00000000 fa0b4000 c03aee90 fffffdfb edd79000 ee646c00 c0474290 de40: 00000000 edda24c0 edd79380 edc81f00 00000000 00000200 00000001 c06dd488 de60: edda3960 ee646c10 ee646c10 c0824cc4 fffffdfb c0880c94 00000002 edc92600 de80: c0836378 c03a7f84 ee646c10 c0824cc4 00000000 c0880c80 c0880c94 c03a6568 dea0: 00000000 ee646c10 c03a66ac ee4f8000 00000000 00000001 edc92600 c03a4b40 dec0: ee404c94 edc83c4c ee646c10 ee646c10 ee646c44 c03a63c4 ee646c10 ee646c10 dee0: c0814448 c03a5aa8 ee646c10 c0814220 edd3c000 c03a5ec0 c0814250 ee6be400 df00: edd3c000 c004e5bc ee6ddb01 00000078 ee6ddb00 ee4f8000 ee6be418 edd3c000 df20: ee4f8028 00000088 c0836045 ee4f8000 ee6be400 c004e928 ee4f8028 00000000 df40: c004e8ec 00000000 ee6bf1c0 ee6be400 c004e8ec 00000000 00000000 00000000 df60: 00000000 c0053450 2e56fa97 00000000 afdffbd7 ee6be400 00000000 00000000 df80: edd3df80 edd3df80 00000000 00000000 edd3df90 edd3df90 edd3dfac ee6bf1c0 dfa0: c0053384 00000000 00000000 c000f668 00000000 00000000 00000000 00000000 dfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 dfe0: 00000000 00000000 00000000 00000000 00000013 00000000 f1fc9d7e febfbdff [<c0471998>] (omap_hsmmc_runtime_suspend) from [<c0029590>] (_od_runtime_suspend+0xc/0x24) [<c0029590>] (_od_runtime_suspend) from [<c03adfb8>] (__rpm_callback+0x24/0x3c) [<c03adfb8>] (__rpm_callback) from [<c03adff0>] (rpm_callback+0x20/0x80) [<c03adff0>] (rpm_callback) from [<c03ae4ec>] (rpm_suspend+0xe4/0x618) [<c03ae4ec>] (rpm_suspend) from [<c03aee90>] (__pm_runtime_idle+0x60/0x80) [<c03aee90>] (__pm_runtime_idle) from [<c0474290>] (omap_hsmmc_probe+0x6bc/0xa7c) [<c0474290>] (omap_hsmmc_probe) from [<c03a7f84>] (platform_drv_probe+0x44/0xa4) [<c03a7f84>] (platform_drv_probe) from [<c03a6568>] (driver_probe_device+0x170/0x2b4) [<c03a6568>] (driver_probe_device) from [<c03a4b40>] (bus_for_each_drv+0x64/0x98) [<c03a4b40>] (bus_for_each_drv) from [<c03a63c4>] (device_attach+0x70/0x88) [<c03a63c4>] (device_attach) from [<c03a5aa8>] (bus_probe_device+0x84/0xac) [<c03a5aa8>] (bus_probe_device) from [<c03a5ec0>] (deferred_probe_work_func+0x58/0x88) [<c03a5ec0>] (deferred_probe_work_func) from [<c004e5bc>] (process_one_work+0x134/0x464) [<c004e5bc>] (process_one_work) from [<c004e928>] (worker_thread+0x3c/0x4fc) [<c004e928>] (worker_thread) from [<c0053450>] (kthread+0xcc/0xe4) [<c0053450>] (kthread) from [<c000f668>] (ret_from_fork+0x14/0x2c) Code: e594302c e593202c e584205c e594302c (e5932128) ---[ end trace 0000000000000002 ]--- The issue happens because omap_device_late_init() do not take into account that some drivers are present, but their probes were not finished successfully and where deferred instead. This is the valid case, and omap_device_late_init() should not idle such devices. To fix this issue, the value of omap_device->_driver_status field should be checked not only for BUS_NOTIFY_BOUND_DRIVER (driver is present and has been bound to device successfully), but also checked for BUS_NOTIFY_BIND_DRIVER (driver about to be bound) - which means driver is present and there was try to bind it to device. [1] http://www.spinics.net/lists/arm-kernel/msg441880.html Cc: Tero Kristo <t-kristo@ti.com> Cc: Keerthy <j-keerthy@ti.com> Tested-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>

The renesas-irqc interrupt controller is cascaded to the GIC. Hence when propagating wake-up settings to its parent interrupt controller, the following lockdep warning is printed: ============================================= [ INFO: possible recursive locking detected ] 4.2.0-ape6evm-10725-g50fcd7643c034198 torvalds#280 Not tainted --------------------------------------------- s2ram/1072 is trying to acquire lock: (&irq_desc_lock_class){-.-...}, at: [<c008d3fc>] __irq_get_desc_lock+0x58/0x98 but task is already holding lock: (&irq_desc_lock_class){-.-...}, at: [<c008d3fc>] __irq_get_desc_lock+0x58/0x98 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&irq_desc_lock_class); lock(&irq_desc_lock_class); *** DEADLOCK *** May be due to missing lock nesting notation 6 locks held by s2ram/1072: #0: (sb_writers#7){.+.+.+}, at: [<c012eb14>] __sb_start_write+0xa0/0xa8 openbmc#1: (&of->mutex){+.+.+.}, at: [<c019396c>] kernfs_fop_write+0x4c/0x1bc openbmc#2: (s_active#24){.+.+.+}, at: [<c0193974>] kernfs_fop_write+0x54/0x1bc openbmc#3: (pm_mutex){+.+.+.}, at: [<c008213c>] pm_suspend+0x10c/0x510 openbmc#4: (&dev->mutex){......}, at: [<c02af3c4>] __device_suspend+0xdc/0x2cc openbmc#5: (&irq_desc_lock_class){-.-...}, at: [<c008d3fc>] __irq_get_desc_lock+0x58/0x98 stack backtrace: CPU: 0 PID: 1072 Comm: s2ram Not tainted 4.2.0-ape6evm-10725-g50fcd7643c034198 torvalds#280 Hardware name: Generic R8A73A4 (Flattened Device Tree) [<c0018078>] (unwind_backtrace) from [<c00144f0>] (show_stack+0x10/0x14) [<c00144f0>] (show_stack) from [<c0451f14>] (dump_stack+0x88/0x98) [<c0451f14>] (dump_stack) from [<c007b29c>] (__lock_acquire+0x15cc/0x20e4) [<c007b29c>] (__lock_acquire) from [<c007c6e0>] (lock_acquire+0xac/0x12c) [<c007c6e0>] (lock_acquire) from [<c0457c00>] (_raw_spin_lock_irqsave+0x40/0x54) [<c0457c00>] (_raw_spin_lock_irqsave) from [<c008d3fc>] (__irq_get_desc_lock+0x58/0x98) [<c008d3fc>] (__irq_get_desc_lock) from [<c008ebbc>] (irq_set_irq_wake+0x20/0xf8) [<c008ebbc>] (irq_set_irq_wake) from [<c0260770>] (irqc_irq_set_wake+0x20/0x4c) [<c0260770>] (irqc_irq_set_wake) from [<c008ec28>] (irq_set_irq_wake+0x8c/0xf8) [<c008ec28>] (irq_set_irq_wake) from [<c02cb8c0>] (gpio_keys_suspend+0x74/0xc0) [<c02cb8c0>] (gpio_keys_suspend) from [<c02ae8cc>] (dpm_run_callback+0x54/0x124) Avoid this false positive by using a separate lockdep class for IRQC interrupts. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Cc: Grygorii Strashko <grygorii.strashko@ti.com> Cc: Magnus Damm <magnus.damm@gmail.com> Cc: Jason Cooper <jason@lakedaemon.net> Link: http://lkml.kernel.org/r/1441798974-25716-2-git-send-email-geert%2Brenesas@glider.be Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

The renesas-intc-irqpin interrupt controller is cascaded to the GIC. Hence when propagating wake-up settings to its parent interrupt controller, the following lockdep warning is printed: ============================================= [ INFO: possible recursive locking detected ] 4.2.0-armadillo-10725-g50fcd7643c034198 torvalds#781 Not tainted --------------------------------------------- s2ram/1179 is trying to acquire lock: (&irq_desc_lock_class){-.-...}, at: [<c005bb54>] __irq_get_desc_lock+0x78/0x94 but task is already holding lock: (&irq_desc_lock_class){-.-...}, at: [<c005bb54>] __irq_get_desc_lock+0x78/0x94 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&irq_desc_lock_class); lock(&irq_desc_lock_class); *** DEADLOCK *** May be due to missing lock nesting notation 7 locks held by s2ram/1179: #0: (sb_writers#7){.+.+.+}, at: [<c00c9708>] __sb_start_write+0x64/0xb8 openbmc#1: (&of->mutex){+.+.+.}, at: [<c0125a00>] kernfs_fop_write+0x78/0x1a0 openbmc#2: (s_active#23){.+.+.+}, at: [<c0125a08>] kernfs_fop_write+0x80/0x1a0 openbmc#3: (autosleep_lock){+.+.+.}, at: [<c0058244>] pm_autosleep_lock+0x18/0x20 openbmc#4: (pm_mutex){+.+.+.}, at: [<c0057e50>] pm_suspend+0x54/0x248 openbmc#5: (&dev->mutex){......}, at: [<c0243a20>] __device_suspend+0xdc/0x240 openbmc#6: (&irq_desc_lock_class){-.-...}, at: [<c005bb54>] __irq_get_desc_lock+0x78/0x94 stack backtrace: CPU: 0 PID: 1179 Comm: s2ram Not tainted 4.2.0-armadillo-10725-g50fcd7643c034198 Hardware name: Generic R8A7740 (Flattened Device Tree) [<c00129f4>] (dump_backtrace) from [<c0012bec>] (show_stack+0x18/0x1c) [<c0012bd4>] (show_stack) from [<c03f5d94>] (dump_stack+0x20/0x28) [<c03f5d74>] (dump_stack) from [<c00514d4>] (__lock_acquire+0x67c/0x1b88) [<c0050e58>] (__lock_acquire) from [<c0052df8>] (lock_acquire+0x9c/0xbc) [<c0052d5c>] (lock_acquire) from [<c03fb068>] (_raw_spin_lock_irqsave+0x44/0x58) [<c03fb024>] (_raw_spin_lock_irqsave) from [<c005bb54>] (__irq_get_desc_lock+0x78/0x94 [<c005badc>] (__irq_get_desc_lock) from [<c005c3d8>] (irq_set_irq_wake+0x28/0x100) [<c005c3b0>] (irq_set_irq_wake) from [<c01e50d0>] (intc_irqpin_irq_set_wake+0x24/0x4c) [<c01e50ac>] (intc_irqpin_irq_set_wake) from [<c005c17c>] (set_irq_wake_real+0x3c/0x50 [<c005c140>] (set_irq_wake_real) from [<c005c414>] (irq_set_irq_wake+0x64/0x100) [<c005c3b0>] (irq_set_irq_wake) from [<c02a19b4>] (gpio_keys_suspend+0x60/0xa0) [<c02a1954>] (gpio_keys_suspend) from [<c023b750>] (platform_pm_suspend+0x3c/0x5c) Avoid this false positive by using a separate lockdep class for INTC External IRQ Pin interrupts. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Cc: Grygorii Strashko <grygorii.strashko@ti.com> Cc: Magnus Damm <magnus.damm@gmail.com> Cc: Jason Cooper <jason@lakedaemon.net> Link: http://lkml.kernel.org/r/1441798974-25716-3-git-send-email-geert%2Brenesas@glider.be Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

My colleague ran into a program stall on a x86_64 server, where n_tty_read() was waiting for data even if there was data in the buffer in the pty. kernel stack for the stuck process looks like below. #0 [ffff88303d107b58] __schedule at ffffffff815c4b20 openbmc#1 [ffff88303d107bd0] schedule at ffffffff815c513e openbmc#2 [ffff88303d107bf0] schedule_timeout at ffffffff815c7818 openbmc#3 [ffff88303d107ca0] wait_woken at ffffffff81096bd2 openbmc#4 [ffff88303d107ce0] n_tty_read at ffffffff8136fa23 openbmc#5 [ffff88303d107dd0] tty_read at ffffffff81368013 openbmc#6 [ffff88303d107e20] __vfs_read at ffffffff811a3704 openbmc#7 [ffff88303d107ec0] vfs_read at ffffffff811a3a57 openbmc#8 [ffff88303d107f00] sys_read at ffffffff811a4306 openbmc#9 [ffff88303d107f50] entry_SYSCALL_64_fastpath at ffffffff815c86d7 There seems to be two problems causing this issue. First, in drivers/tty/n_tty.c, __receive_buf() stores the data and updates ldata->commit_head using smp_store_release() and then checks the wait queue using waitqueue_active(). However, since there is no memory barrier, __receive_buf() could return without calling wake_up_interactive_poll(), and at the same time, n_tty_read() could start to wait in wait_woken() as in the following chart. __receive_buf() n_tty_read() ------------------------------------------------------------------------ if (waitqueue_active(&tty->read_wait)) /* Memory operations issued after the RELEASE may be completed before the RELEASE operation has completed */ add_wait_queue(&tty->read_wait, &wait); ... if (!input_available_p(tty, 0)) { smp_store_release(&ldata->commit_head, ldata->read_head); ... timeout = wait_woken(&wait, TASK_INTERRUPTIBLE, timeout); ------------------------------------------------------------------------ The second problem is that n_tty_read() also lacks a memory barrier call and could also cause __receive_buf() to return without calling wake_up_interactive_poll(), and n_tty_read() to wait in wait_woken() as in the chart below. __receive_buf() n_tty_read() ------------------------------------------------------------------------ spin_lock_irqsave(&q->lock, flags); /* from add_wait_queue() */ ... if (!input_available_p(tty, 0)) { /* Memory operations issued after the RELEASE may be completed before the RELEASE operation has completed */ smp_store_release(&ldata->commit_head, ldata->read_head); if (waitqueue_active(&tty->read_wait)) __add_wait_queue(q, wait); spin_unlock_irqrestore(&q->lock,flags); /* from add_wait_queue() */ ... timeout = wait_woken(&wait, TASK_INTERRUPTIBLE, timeout); ------------------------------------------------------------------------ There are also other places in drivers/tty/n_tty.c which have similar calls to waitqueue_active(), so instead of adding many memory barrier calls, this patch simply removes the call to waitqueue_active(), leaving just wake_up*() behind. This fixes both problems because, even though the memory access before or after the spinlocks in both wake_up*() and add_wait_queue() can sneak into the critical section, it cannot go past it and the critical section assures that they will be serialized (please see "INTER-CPU ACQUIRING BARRIER EFFECTS" in Documentation/memory-barriers.txt for a better explanation). Moreover, the resulting code is much simpler. Latency measurement using a ping-pong test over a pty doesn't show any visible performance drop. Signed-off-by: Kosuke Tatsukawa <tatsu@ab.jp.nec.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When a43eec3 ("bpf: introduce bpf_perf_event_output() helper") added PERF_COUNT_SW_BPF_OUTPUT we ended up with a new entry in the event_symbols_sw array that wasn't initialized, thus set to NULL, fix print_symbol_events() to check for that case so that we don't crash if this happens again. (gdb) bt #0 __match_glob (ignore_space=false, pat=<optimized out>, str=<optimized out>) at util/string.c:198 #1 strglobmatch (str=<optimized out>, pat=pat@entry=0x7fffffffe61d "stall") at util/string.c:252 #2 0x00000000004993a5 in print_symbol_events (type=1, syms=0x872880 <event_symbols_sw+160>, max=11, name_only=false, event_glob=0x7fffffffe61d "stall") at util/parse-events.c:1615 #3 print_events (event_glob=event_glob@entry=0x7fffffffe61d "stall", name_only=false) at util/parse-events.c:1675 #4 0x000000000042c79e in cmd_list (argc=1, argv=0x7fffffffe390, prefix=<optimized out>) at builtin-list.c:68 #5 0x00000000004788a5 in run_builtin (p=p@entry=0x871758 <commands+120>, argc=argc@entry=2, argv=argv@entry=0x7fffffffe390) at perf.c:370 #6 0x0000000000420ab0 in handle_internal_command (argv=0x7fffffffe390, argc=2) at perf.c:429 #7 run_argv (argv=0x7fffffffe110, argcp=0x7fffffffe11c) at perf.c:473 #8 main (argc=2, argv=0x7fffffffe390) at perf.c:588 (gdb) p event_symbols_sw[PERF_COUNT_SW_BPF_OUTPUT] $4 = {symbol = 0x0, alias = 0x0} (gdb) A patch to robustify perf to not segfault when the next counter gets added in the kernel will follow this one. Reported-by: Ingo Molnar <mingo@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexei Starovoitov <ast@kernel.org> Cc: David Ahern <dsahern@gmail.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Wang Nan <wangnan0@huawei.com> Link: http://lkml.kernel.org/n/tip-57wysblcjfrseb0zg5u7ek10@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

…arm header commit a6002ec upstream. arm and arm64 use different config options to specify big endian. This needs taking into account when including code/headers between the two architectures. A case in point is PAN, which uses the __instr_arm() macro to output instructions. The macro comes from opcodes.h, which lives under arch/arm. On a big-endian build the mismatched config options mean the instruction isn't byte swapped correctly, resulting in undefined instruction exceptions during boot: | alternatives: patching kernel code | kdevtmpfs[87]: undefined instruction: pc=ffffffc0004505b4 | kdevtmpfs[87]: undefined instruction: pc=ffffffc00076231c | kdevtmpfs[87]: undefined instruction: pc=ffffffc00076231c | kdevtmpfs[87]: undefined instruction: pc=ffffffc00076231c | kdevtmpfs[87]: undefined instruction: pc=ffffffc00076231c | kdevtmpfs[87]: undefined instruction: pc=ffffffc00076231c | kdevtmpfs[87]: undefined instruction: pc=ffffffc00076231c | kdevtmpfs[87]: undefined instruction: pc=ffffffc00076231c | kdevtmpfs[87]: undefined instruction: pc=ffffffc00076231c | kdevtmpfs[87]: undefined instruction: pc=ffffffc00076231c | Internal error: Oops - undefined instruction: 0 [#1] SMP | Modules linked in: | CPU: 0 PID: 87 Comm: kdevtmpfs Not tainted 4.1.16+ #5 | Hardware name: Hisilicon PhosphorHi1382 EVB (DT) | task: ffffffc336591700 ti: ffffffc3365a4000 task.ti: ffffffc3365a4000 | PC is at dump_instr+0x68/0x100 | LR is at do_undefinstr+0x1d4/0x2a4 | pc : [<ffffffc00076231c>] lr : [<ffffffc0000811d4>] pstate: 604001c5 | sp : ffffffc3365a6450 Reported-by: Hanjun Guo <guohanjun@huawei.com> Tested-by: Xuefeng Wang <wxf.wang@hisilicon.com> Signed-off-by: James Morse <james.morse@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c9eb13a upstream. If the orphaned inode list contains inode #5, ext4_iget() returns a bad inode (since the bootloader inode should never be referenced directly). Because of the bad inode, we end up processing the inode repeatedly and this hangs the machine. This can be reproduced via: mke2fs -t ext4 /tmp/foo.img 100 debugfs -w -R "ssv last_orphan 5" /tmp/foo.img mount -o loop /tmp/foo.img /mnt (But don't do this if you are using an unpatched kernel if you care about the system staying functional. :-) This bug was found by the port of American Fuzzy Lop into the kernel to find file system problems[1]. (Since it *only* happens if inode #5 shows up on the orphan list --- 3, 7, 8, etc. won't do it, it's not surprising that AFL needed two hours before it found it.) [1] http://events.linuxfoundation.org/sites/events/files/slides/AFL%20filesystem%20fuzzing%2C%20Vault%202016_0.pdf Reported by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The incorrect GPIO mask cause kernel warning, when AR9462 access GPIO11. Also fix the mask for AR9565. WARNING: CPU: 1 PID: 199 at ../drivers/net/wireless/ath/ath9k/hw.c:2778 ath9k_hw_gpio_get+0x1a9/0x1b0 [ath9k_hw] CPU: 1 PID: 199 Comm: kworker/u16:9 Not tainted 4.7.0-rc1-next-20160530+ openbmc#5 Hardware name: Acer TravelMate P243/BA40_HC, BIOS V1.01 04/20/2012 Workqueue: events_power_efficient rfkill_poll 0000000000000000 ffff88002cf73d28 ffffffff813b8ddc 0000000000000000 0000000000000000 ffff88002cf73d68 ffffffff8107a331 00000ada00000086 ffff880148d9c018 000000000000000b ffff880147e68720 0000000000000200 Call Trace: [<ffffffff813b8ddc>] dump_stack+0x63/0x87 [<ffffffff8107a331>] __warn+0xd1/0xf0 [<ffffffff8107a41d>] warn_slowpath_null+0x1d/0x20 [<ffffffffc0775b19>] ath9k_hw_gpio_get+0x1a9/0x1b0 [ath9k_hw] [<ffffffffc047f3e4>] ath9k_rfkill_poll_state+0x34/0x60 [ath9k] [<ffffffffc06dbb53>] ieee80211_rfkill_poll+0x33/0x40 [mac80211] [<ffffffffc03ad65a>] cfg80211_rfkill_poll+0x2a/0xc0 [cfg80211] [<ffffffff817c5514>] rfkill_poll+0x24/0x50 [<ffffffff81093183>] process_one_work+0x153/0x3f0 [<ffffffff8109393b>] worker_thread+0x12b/0x4b0 [<ffffffff81093810>] ? rescuer_thread+0x340/0x340 [<ffffffff81099129>] kthread+0xc9/0xe0 [<ffffffff817d8f1f>] ret_from_fork+0x1f/0x40 [<ffffffff81099060>] ? kthread_park+0x60/0x60 Fixes: a01ab81 ("ath9k: define correct GPIO numbers and bits mask") Reported-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk> Tested-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk> Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

commit c9eb13a upstream. If the orphaned inode list contains inode #5, ext4_iget() returns a bad inode (since the bootloader inode should never be referenced directly). Because of the bad inode, we end up processing the inode repeatedly and this hangs the machine. This can be reproduced via: mke2fs -t ext4 /tmp/foo.img 100 debugfs -w -R "ssv last_orphan 5" /tmp/foo.img mount -o loop /tmp/foo.img /mnt (But don't do this if you are using an unpatched kernel if you care about the system staying functional. :-) This bug was found by the port of American Fuzzy Lop into the kernel to find file system problems[1]. (Since it *only* happens if inode #5 shows up on the orphan list --- 3, 7, 8, etc. won't do it, it's not surprising that AFL needed two hours before it found it.) [1] http://events.linuxfoundation.org/sites/events/files/slides/AFL%20filesystem%20fuzzing%2C%20Vault%202016_0.pdf Reported by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ec183d2 upstream. Fixes segmentation fault using, for instance: (gdb) run record -I -e intel_pt/tsc=1,noretcomp=1/u /bin/ls Starting program: /home/acme/bin/perf record -I -e intel_pt/tsc=1,noretcomp=1/u /bin/ls Missing separate debuginfos, use: dnf debuginfo-install glibc-2.22-7.fc23.x86_64 [Thread debugging using libthread_db enabled] Using host libthread_db library "/lib64/libthread_db.so.1". Program received signal SIGSEGV, Segmentation fault. 0 x00000000004b9ea5 in tracepoint_error (e=0x0, err=13, sys=0x19b1370 "sched", name=0x19a5d00 "sched_switch") at util/parse-events.c:410 (gdb) bt #0 0x00000000004b9ea5 in tracepoint_error (e=0x0, err=13, sys=0x19b1370 "sched", name=0x19a5d00 "sched_switch") at util/parse-events.c:410 openbmc#1 0x00000000004b9fc5 in add_tracepoint (list=0x19a5d20, idx=0x7fffffffb8c0, sys_name=0x19b1370 "sched", evt_name=0x19a5d00 "sched_switch", err=0x0, head_config=0x0) at util/parse-events.c:433 openbmc#2 0x00000000004ba334 in add_tracepoint_event (list=0x19a5d20, idx=0x7fffffffb8c0, sys_name=0x19b1370 "sched", evt_name=0x19a5d00 "sched_switch", err=0x0, head_config=0x0) at util/parse-events.c:498 openbmc#3 0x00000000004bb699 in parse_events_add_tracepoint (list=0x19a5d20, idx=0x7fffffffb8c0, sys=0x19b1370 "sched", event=0x19a5d00 "sched_switch", err=0x0, head_config=0x0) at util/parse-events.c:936 openbmc#4 0x00000000004f6eda in parse_events_parse (_data=0x7fffffffb8b0, scanner=0x19a49d0) at util/parse-events.y:391 openbmc#5 0x00000000004bc8e5 in parse_events__scanner (str=0x663ff2 "sched:sched_switch", data=0x7fffffffb8b0, start_token=258) at util/parse-events.c:1361 openbmc#6 0x00000000004bca57 in parse_events (evlist=0x19a5220, str=0x663ff2 "sched:sched_switch", err=0x0) at util/parse-events.c:1401 openbmc#7 0x0000000000518d5f in perf_evlist__can_select_event (evlist=0x19a3b90, str=0x663ff2 "sched:sched_switch") at util/record.c:253 openbmc#8 0x0000000000553c42 in intel_pt_track_switches (evlist=0x19a3b90) at arch/x86/util/intel-pt.c:364 openbmc#9 0x00000000005549d1 in intel_pt_recording_options (itr=0x19a2c40, evlist=0x19a3b90, opts=0x8edf68 <record+232>) at arch/x86/util/intel-pt.c:664 openbmc#10 0x000000000051e076 in auxtrace_record__options (itr=0x19a2c40, evlist=0x19a3b90, opts=0x8edf68 <record+232>) at util/auxtrace.c:539 openbmc#11 0x0000000000433368 in cmd_record (argc=1, argv=0x7fffffffde60, prefix=0x0) at builtin-record.c:1264 openbmc#12 0x000000000049bec2 in run_builtin (p=0x8fa2a8 <commands+168>, argc=5, argv=0x7fffffffde60) at perf.c:390 openbmc#13 0x000000000049c12a in handle_internal_command (argc=5, argv=0x7fffffffde60) at perf.c:451 openbmc#14 0x000000000049c278 in run_argv (argcp=0x7fffffffdcbc, argv=0x7fffffffdcb0) at perf.c:495 openbmc#15 0x000000000049c60a in main (argc=5, argv=0x7fffffffde60) at perf.c:618 (gdb) Intel PT attempts to find the sched:sched_switch tracepoint but that seg faults if tracefs is not readable, because the error reporting structure is null, as errors are not reported when automatically adding tracepoints. Fix by checking before using. Committer note: This doesn't take place in a kernel that supports perf_event_attr.context_switch, that is the default way that will be used for tracking context switches, only in older kernels, like 4.2, in a machine with Intel PT (e.g. Broadwell) for non-priviledged users. Further info from a similar patch by Wang: The error is in tracepoint_error: it assumes the 'e' parameter is valid. However, there are many situation a parse_event() can be called without parse_events_error. See result of $ grep 'parse_events(.*NULL)' ./tools/perf/ -r' Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Tong Zhang <ztong@vt.edu> Cc: Wang Nan <wangnan0@huawei.com> Fixes: 1965817 ("perf tools: Enhance parsing events tracepoint error output") Link: http://lkml.kernel.org/r/1453809921-24596-2-git-send-email-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d144dfe upstream. If we use USB ID pin as wakeup source, and there is a USB block device on this USB OTG (ID) cable, the system will be deadlock after system resume. The root cause for this problem is: the workqueue ci_otg may try to remove hcd before the driver resume has finished, and hcd will disconnect the device on it, then, it will call device_release_driver, and holds the device lock "dev->mutex", but it is never unlocked since it waits workqueue writeback to run to flush the block information, but the workqueue writeback is freezable, it is not thawed before driver resume has finished. When the driver (device: sd 0:0:0:0:) resume goes to dpm_complete, it tries to get its device lock "dev->mutex", but it can't get it forever, then the deadlock occurs. Below call stacks show the situation. So, in order to fix this problem, we need to change workqueue ci_otg as freezable, then the work item in this workqueue will be run after driver's resume, this workqueue will not be blocked forever like above case since the workqueue writeback has been thawed too. Tested at: i.mx6qdl-sabresd and i.mx6sx-sdb. [ 555.178869] kworker/u2:13 D c07de74c 0 826 2 0x00000000 [ 555.185310] Workqueue: ci_otg ci_otg_work [ 555.189353] Backtrace: [ 555.191849] [<c07de4fc>] (__schedule) from [<c07dec6c>] (schedule+0x48/0xa0) [ 555.198912] r10:ee471ba0 r9:00000000 r8:00000000 r7:00000002 r6:ee470000 r5:ee471ba4 [ 555.206867] r4:ee470000 [ 555.209453] [<c07dec24>] (schedule) from [<c07e2fc4>] (schedule_timeout+0x15c/0x1e0) [ 555.217212] r4:7fffffff r3:edc2b000 [ 555.220862] [<c07e2e68>] (schedule_timeout) from [<c07df6c8>] (wait_for_common+0x94/0x144) [ 555.229140] r8:00000000 r7:00000002 r6:ee470000 r5:ee471ba4 r4:7fffffff [ 555.235980] [<c07df634>] (wait_for_common) from [<c07df790>] (wait_for_completion+0x18/0x1c) [ 555.244430] r10:00000001 r9:c0b5563c r8:c0042e48 r7:ef086000 r6:eea4372c r5:ef131b00 [ 555.252383] r4:00000000 [ 555.254970] [<c07df778>] (wait_for_completion) from [<c0043cb8>] (flush_work+0x19c/0x234) [ 555.263177] [<c0043b1c>] (flush_work) from [<c0043fac>] (flush_delayed_work+0x48/0x4c) [ 555.271106] r8:ed5b5000 r7:c0b38a3c r6:eea439cc r5:eea4372c r4:eea4372c [ 555.277958] [<c0043f64>] (flush_delayed_work) from [<c00eae18>] (bdi_unregister+0x84/0xec) [ 555.286236] r4:eea43520 r3:20000153 [ 555.289885] [<c00ead94>] (bdi_unregister) from [<c02c2154>] (blk_cleanup_queue+0x180/0x29c) [ 555.298250] r5:eea43808 r4:eea43400 [ 555.301909] [<c02c1fd4>] (blk_cleanup_queue) from [<c0417914>] (__scsi_remove_device+0x48/0xb8) [ 555.310623] r7:00000000 r6:20000153 r5:ededa950 r4:ededa800 [ 555.316403] [<c04178cc>] (__scsi_remove_device) from [<c0415e90>] (scsi_forget_host+0x64/0x68) [ 555.325028] r5:ededa800 r4:ed5b5000 [ 555.328689] [<c0415e2c>] (scsi_forget_host) from [<c0409828>] (scsi_remove_host+0x78/0x104) [ 555.337054] r5:ed5b5068 r4:ed5b5000 [ 555.340709] [<c04097b0>] (scsi_remove_host) from [<c04cdfcc>] (usb_stor_disconnect+0x50/0xb4) [ 555.349247] r6:ed5b56e4 r5:ed5b5818 r4:ed5b5690 r3:00000008 [ 555.355025] [<c04cdf7c>] (usb_stor_disconnect) from [<c04b3bc8>] (usb_unbind_interface+0x78/0x25c) [ 555.363997] r8:c13919b4 r7:edd3c000 r6:edd3c020 r5:ee551c68 r4:ee551c00 r3:c04cdf7c [ 555.371892] [<c04b3b50>] (usb_unbind_interface) from [<c03dc248>] (__device_release_driver+0x8c/0x118) [ 555.381213] r10:00000001 r9:edd90c00 r8:c13919b4 r7:ee551c68 r6:c0b546e0 r5:c0b5563c [ 555.389167] r4:edd3c020 [ 555.391752] [<c03dc1bc>] (__device_release_driver) from [<c03dc2fc>] (device_release_driver+0x28/0x34) [ 555.401071] r5:edd3c020 r4:edd3c054 [ 555.404721] [<c03dc2d4>] (device_release_driver) from [<c03db304>] (bus_remove_device+0xe0/0x110) [ 555.413607] r5:edd3c020 r4:ef17f04c [ 555.417253] [<c03db224>] (bus_remove_device) from [<c03d8128>] (device_del+0x114/0x21c) [ 555.425270] r6:edd3c028 r5:edd3c020 r4:ee551c00 r3:00000000 [ 555.431045] [<c03d8014>] (device_del) from [<c04b1560>] (usb_disable_device+0xa4/0x1e8) [ 555.439061] r8:edd3c000 r7:eded8000 r6:00000000 r5:00000001 r4:ee551c00 [ 555.445906] [<c04b14bc>] (usb_disable_device) from [<c04a8e54>] (usb_disconnect+0x74/0x224) [ 555.454271] r9:edd90c00 r8:ee551000 r7:ee551c68 r6:ee551c9c r5:ee551c00 r4:00000001 [ 555.462156] [<c04a8de0>] (usb_disconnect) from [<c04a8fb8>] (usb_disconnect+0x1d8/0x224) [ 555.470259] r10:00000001 r9:edd90000 r8:ee471e2c r7:ee551468 r6:ee55149c r5:ee551400 [ 555.478213] r4:00000001 [ 555.480797] [<c04a8de0>] (usb_disconnect) from [<c04ae5ec>] (usb_remove_hcd+0xa0/0x1ac) [ 555.488813] r10:00000001 r9:ee471eb0 r8:00000000 r7:ef3d9500 r6:eded810c r5:eded80b0 [ 555.496765] r4:eded8000 [ 555.499351] [<c04ae54c>] (usb_remove_hcd) from [<c04d4158>] (host_stop+0x28/0x64) [ 555.506847] r6:eeb50010 r5:eded8000 r4:eeb51010 [ 555.511563] [<c04d4130>] (host_stop) from [<c04d09b8>] (ci_otg_work+0xc4/0x124) [ 555.518885] r6:00000001 r5:eeb50010 r4:eeb502a0 r3:c04d4130 [ 555.524665] [<c04d08f4>] (ci_otg_work) from [<c00454f0>] (process_one_work+0x194/0x420) [ 555.532682] r6:ef086000 r5:eeb502a0 r4:edc44480 [ 555.537393] [<c004535c>] (process_one_work) from [<c00457b0>] (worker_thread+0x34/0x514) [ 555.545496] r10:edc44480 r9:ef086000 r8:c0b1a100 r7:ef086034 r6:00000088 r5:edc44498 [ 555.553450] r4:ef086000 [ 555.556032] [<c004577c>] (worker_thread) from [<c004bab4>] (kthread+0xdc/0xf8) [ 555.563268] r10:00000000 r9:00000000 r8:00000000 r7:c004577c r6:edc44480 r5:eddc15c0 [ 555.571221] r4:00000000 [ 555.573804] [<c004b9d8>] (kthread) from [<c000fef0>] (ret_from_fork+0x14/0x24) [ 555.581040] r7:00000000 r6:00000000 r5:c004b9d8 r4:eddc15c0 [ 553.429383] sh D c07de74c 0 694 691 0x00000000 [ 553.435801] Backtrace: [ 553.438295] [<c07de4fc>] (__schedule) from [<c07dec6c>] (schedule+0x48/0xa0) [ 553.445358] r10:edd3c054 r9:edd3c078 r8:edddbd50 r7:edcbbc00 r6:c1377c34 r5:60000153 [ 553.453313] r4:eddda000 [ 553.455896] [<c07dec24>] (schedule) from [<c07deff8>] (schedule_preempt_disabled+0x10/0x14) [ 553.464261] r4:edd3c058 r3:0000000a [ 553.467910] [<c07defe8>] (schedule_preempt_disabled) from [<c07e0bbc>] (mutex_lock_nested+0x1a0/0x3e8) [ 553.477254] [<c07e0a1c>] (mutex_lock_nested) from [<c03e927c>] (dpm_complete+0xc0/0x1b0) [ 553.485358] r10:00561408 r9:edd3c054 r8:c0b4863c r7:edddbd90 r6:c0b485d8 r5:edd3c020 [ 553.493313] r4:edd3c0d0 [ 553.495896] [<c03e91bc>] (dpm_complete) from [<c03e9388>] (dpm_resume_end+0x1c/0x20) [ 553.503652] r9:00000000 r8:c0b1a9d0 r7:c1334ec0 r6:c1334edc r5:00000003 r4:00000010 [ 553.511544] [<c03e936c>] (dpm_resume_end) from [<c0079894>] (suspend_devices_and_enter+0x158/0x504) [ 553.520604] r4:00000000 r3:c1334efc [ 553.524250] [<c007973c>] (suspend_devices_and_enter) from [<c0079e74>] (pm_suspend+0x234/0x2cc) [ 553.532961] r10:00561408 r9:ed6b7300 r8:00000004 r7:c1334eec r6:00000000 r5:c1334ee8 [ 553.540914] r4:00000003 [ 553.543493] [<c0079c40>] (pm_suspend) from [<c0078a6c>] (state_store+0x6c/0xc0) [ 555.703684] 7 locks held by kworker/u2:13/826: [ 555.708140] #0: ("%s""ci_otg"){++++.+}, at: [<c0045484>] process_one_work+0x128/0x420 [ 555.716277] openbmc#1: ((&ci->work)){+.+.+.}, at: [<c0045484>] process_one_work+0x128/0x420 [ 555.724317] openbmc#2: (usb_bus_list_lock){+.+.+.}, at: [<c04ae5e4>] usb_remove_hcd+0x98/0x1ac [ 555.732626] openbmc#3: (&dev->mutex){......}, at: [<c04a8e28>] usb_disconnect+0x48/0x224 [ 555.740403] openbmc#4: (&dev->mutex){......}, at: [<c04a8e28>] usb_disconnect+0x48/0x224 [ 555.748179] openbmc#5: (&dev->mutex){......}, at: [<c03dc2f4>] device_release_driver+0x20/0x34 [ 555.756487] openbmc#6: (&shost->scan_mutex){+.+.+.}, at: [<c04097d0>] scsi_remove_host+0x20/0x104 Cc: Jun Li <jun.li@nxp.com> Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm_connector_register_all requires a few too many locks because our connector_list locking is busted. Add another FIXME+hack to work around this. This should address the below lockdep splat: ====================================================== [ INFO: possible circular locking dependency detected ] 4.7.0-rc5+ torvalds#524 Tainted: G O ------------------------------------------------------- kworker/u8:0/6 is trying to acquire lock: (&dev->mode_config.mutex){+.+.+.}, at: [<ffffffff815afde0>] drm_modeset_lock_all+0x40/0x120 but task is already holding lock: ((fb_notifier_list).rwsem){++++.+}, at: [<ffffffff810ac195>] __blocking_notifier_call_chain+0x35/0x70 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> openbmc#1 ((fb_notifier_list).rwsem){++++.+}: [<ffffffff810df611>] lock_acquire+0xb1/0x200 [<ffffffff819a55b4>] down_write+0x44/0x80 [<ffffffff810abf91>] blocking_notifier_chain_register+0x21/0xb0 [<ffffffff814c7448>] fb_register_client+0x18/0x20 [<ffffffff814c6c86>] backlight_device_register+0x136/0x260 [<ffffffffa0127eb2>] intel_backlight_device_register+0xa2/0x160 [i915] [<ffffffffa00f46be>] intel_connector_register+0xe/0x10 [i915] [<ffffffffa0112bfb>] intel_dp_connector_register+0x1b/0x80 [i915] [<ffffffff8159dfea>] drm_connector_register+0x4a/0x80 [<ffffffff8159fe44>] drm_connector_register_all+0x64/0xf0 [<ffffffff815a2a64>] drm_modeset_register_all+0x174/0x1c0 [<ffffffff81599b72>] drm_dev_register+0xc2/0xd0 [<ffffffffa00621d7>] i915_driver_load+0x1547/0x2200 [i915] [<ffffffffa006d80f>] i915_pci_probe+0x4f/0x70 [i915] [<ffffffff814a2135>] local_pci_probe+0x45/0xa0 [<ffffffff814a349b>] pci_device_probe+0xdb/0x130 [<ffffffff815c07e3>] driver_probe_device+0x223/0x440 [<ffffffff815c0ad5>] __driver_attach+0xd5/0x100 [<ffffffff815be386>] bus_for_each_dev+0x66/0xa0 [<ffffffff815c002e>] driver_attach+0x1e/0x20 [<ffffffff815bf9be>] bus_add_driver+0x1ee/0x280 [<ffffffff815c1810>] driver_register+0x60/0xe0 [<ffffffff814a1a10>] __pci_register_driver+0x60/0x70 [<ffffffffa01a905b>] i915_init+0x5b/0x62 [i915] [<ffffffff8100042d>] do_one_initcall+0x3d/0x150 [<ffffffff811a935b>] do_init_module+0x5f/0x1d9 [<ffffffff81124416>] load_module+0x20e6/0x27e0 [<ffffffff81124d63>] SYSC_finit_module+0xc3/0xf0 [<ffffffff81124dae>] SyS_finit_module+0xe/0x10 [<ffffffff819a83a9>] entry_SYSCALL_64_fastpath+0x1c/0xac -> #0 (&dev->mode_config.mutex){+.+.+.}: [<ffffffff810df0ac>] __lock_acquire+0x10fc/0x1260 [<ffffffff810df611>] lock_acquire+0xb1/0x200 [<ffffffff819a3097>] mutex_lock_nested+0x67/0x3c0 [<ffffffff815afde0>] drm_modeset_lock_all+0x40/0x120 [<ffffffff8158f79b>] drm_fb_helper_restore_fbdev_mode_unlocked+0x2b/0x80 [<ffffffff8158f81d>] drm_fb_helper_set_par+0x2d/0x50 [<ffffffffa0105f7a>] intel_fbdev_set_par+0x1a/0x60 [i915] [<ffffffff814c13c6>] fbcon_init+0x586/0x610 [<ffffffff8154d16a>] visual_init+0xca/0x130 [<ffffffff8154e611>] do_bind_con_driver+0x1c1/0x3a0 [<ffffffff8154eaf6>] do_take_over_console+0x116/0x180 [<ffffffff814bd3a7>] do_fbcon_takeover+0x57/0xb0 [<ffffffff814c1e48>] fbcon_event_notify+0x658/0x750 [<ffffffff810abcae>] notifier_call_chain+0x3e/0xb0 [<ffffffff810ac1ad>] __blocking_notifier_call_chain+0x4d/0x70 [<ffffffff810ac1e6>] blocking_notifier_call_chain+0x16/0x20 [<ffffffff814c748b>] fb_notifier_call_chain+0x1b/0x20 [<ffffffff814c86b1>] register_framebuffer+0x251/0x330 [<ffffffff8158fa9f>] drm_fb_helper_initial_config+0x25f/0x3f0 [<ffffffffa0106b48>] intel_fbdev_initial_config+0x18/0x30 [i915] [<ffffffff810adfd8>] async_run_entry_fn+0x48/0x150 [<ffffffff810a3947>] process_one_work+0x1e7/0x750 [<ffffffff810a3efb>] worker_thread+0x4b/0x4f0 [<ffffffff810aad4f>] kthread+0xef/0x110 [<ffffffff819a85ef>] ret_from_fork+0x1f/0x40 other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock((fb_notifier_list).rwsem); lock(&dev->mode_config.mutex); lock((fb_notifier_list).rwsem); lock(&dev->mode_config.mutex); *** DEADLOCK *** 6 locks held by kworker/u8:0/6: #0: ("events_unbound"){.+.+.+}, at: [<ffffffff810a38c9>] process_one_work+0x169/0x750 openbmc#1: ((&entry->work)){+.+.+.}, at: [<ffffffff810a38c9>] process_one_work+0x169/0x750 openbmc#2: (registration_lock){+.+.+.}, at: [<ffffffff814c8487>] register_framebuffer+0x27/0x330 openbmc#3: (console_lock){+.+.+.}, at: [<ffffffff814c86ce>] register_framebuffer+0x26e/0x330 openbmc#4: (&fb_info->lock){+.+.+.}, at: [<ffffffff814c78dd>] lock_fb_info+0x1d/0x40 openbmc#5: ((fb_notifier_list).rwsem){++++.+}, at: [<ffffffff810ac195>] __blocking_notifier_call_chain+0x35/0x70 stack backtrace: CPU: 2 PID: 6 Comm: kworker/u8:0 Tainted: G O 4.7.0-rc5+ torvalds#524 Hardware name: Intel Corp. Broxton P/NOTEBOOK, BIOS APLKRVPA.X64.0138.B33.1606250842 06/25/2016 Workqueue: events_unbound async_run_entry_fn 0000000000000000 ffff8800758577f0 ffffffff814507a5 ffffffff828b9900 ffffffff828b9900 ffff880075857830 ffffffff810dc6fa ffff880075857880 ffff88007584d688 0000000000000005 0000000000000006 ffff88007584d6b0 Call Trace: [<ffffffff814507a5>] dump_stack+0x67/0x92 [<ffffffff810dc6fa>] print_circular_bug+0x1aa/0x200 [<ffffffff810df0ac>] __lock_acquire+0x10fc/0x1260 [<ffffffff810df611>] lock_acquire+0xb1/0x200 [<ffffffff815afde0>] ? drm_modeset_lock_all+0x40/0x120 [<ffffffff815afde0>] ? drm_modeset_lock_all+0x40/0x120 [<ffffffff819a3097>] mutex_lock_nested+0x67/0x3c0 [<ffffffff815afde0>] ? drm_modeset_lock_all+0x40/0x120 [<ffffffff810fa85f>] ? rcu_read_lock_sched_held+0x7f/0x90 [<ffffffff81208218>] ? kmem_cache_alloc_trace+0x248/0x2b0 [<ffffffff815afdc5>] ? drm_modeset_lock_all+0x25/0x120 [<ffffffff815afde0>] drm_modeset_lock_all+0x40/0x120 [<ffffffff8158f79b>] drm_fb_helper_restore_fbdev_mode_unlocked+0x2b/0x80 [<ffffffff8158f81d>] drm_fb_helper_set_par+0x2d/0x50 [<ffffffffa0105f7a>] intel_fbdev_set_par+0x1a/0x60 [i915] [<ffffffff814c13c6>] fbcon_init+0x586/0x610 [<ffffffff8154d16a>] visual_init+0xca/0x130 [<ffffffff8154e611>] do_bind_con_driver+0x1c1/0x3a0 [<ffffffff8154eaf6>] do_take_over_console+0x116/0x180 [<ffffffff814bd3a7>] do_fbcon_takeover+0x57/0xb0 [<ffffffff814c1e48>] fbcon_event_notify+0x658/0x750 [<ffffffff810abcae>] notifier_call_chain+0x3e/0xb0 [<ffffffff810ac1ad>] __blocking_notifier_call_chain+0x4d/0x70 [<ffffffff810ac1e6>] blocking_notifier_call_chain+0x16/0x20 [<ffffffff814c748b>] fb_notifier_call_chain+0x1b/0x20 [<ffffffff814c86b1>] register_framebuffer+0x251/0x330 [<ffffffff815b7e8d>] ? vga_switcheroo_client_fb_set+0x5d/0x70 [<ffffffff8158fa9f>] drm_fb_helper_initial_config+0x25f/0x3f0 [<ffffffffa0106b48>] intel_fbdev_initial_config+0x18/0x30 [i915] [<ffffffff810adfd8>] async_run_entry_fn+0x48/0x150 [<ffffffff810a3947>] process_one_work+0x1e7/0x750 [<ffffffff810a38c9>] ? process_one_work+0x169/0x750 [<ffffffff810a3efb>] worker_thread+0x4b/0x4f0 [<ffffffff810a3eb0>] ? process_one_work+0x750/0x750 [<ffffffff810aad4f>] kthread+0xef/0x110 [<ffffffff819a85ef>] ret_from_fork+0x1f/0x40 [<ffffffff810aac60>] ? kthread_stop+0x2e0/0x2e0 v2: Rebase onto the right branch (hand-editing patches ftw) and add more reporters. Reported-by: Imre Deak <imre.deak@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Acked-by: Chris Wilson <chris@chris-wilson.co.uk> Reported-by: Jiri Kosina <jikos@kernel.org> Cc: Jiri Kosina <jikos@kernel.org> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>

If kexec_apply_relocations fails, kexec_load_purgatory frees pi->sechdrs and pi->purgatory_buf. This is redundant, because in case of error kimage_file_prepare_segments calls kimage_file_post_load_cleanup, which will also free those buffers. This causes two warnings like the following, one for pi->sechdrs and the other for pi->purgatory_buf: kexec-bzImage64: Loading purgatory failed ------------[ cut here ]------------ WARNING: CPU: 1 PID: 2119 at mm/vmalloc.c:1490 __vunmap+0xc1/0xd0 Trying to vfree() nonexistent vm area (ffffc90000e91000) Modules linked in: CPU: 1 PID: 2119 Comm: kexec Not tainted 4.8.0-rc3+ openbmc#5 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 Call Trace: dump_stack+0x4d/0x65 __warn+0xcb/0xf0 warn_slowpath_fmt+0x4f/0x60 ? find_vmap_area+0x19/0x70 ? kimage_file_post_load_cleanup+0x47/0xb0 __vunmap+0xc1/0xd0 vfree+0x2e/0x70 kimage_file_post_load_cleanup+0x5e/0xb0 SyS_kexec_file_load+0x448/0x680 ? putname+0x54/0x60 ? do_sys_open+0x190/0x1f0 entry_SYSCALL_64_fastpath+0x13/0x8f ---[ end trace 158bb74f5950ca2b ]--- Fix by setting pi->sechdrs an pi->purgatory_buf to NULL, since vfree won't try to free a NULL pointer. Link: http://lkml.kernel.org/r/1472083546-23683-1-git-send-email-bauerman@linux.vnet.ibm.com Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com> Acked-by: Baoquan He <bhe@redhat.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Dave Young <dyoung@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

commit 070c43e upstream. If kexec_apply_relocations fails, kexec_load_purgatory frees pi->sechdrs and pi->purgatory_buf. This is redundant, because in case of error kimage_file_prepare_segments calls kimage_file_post_load_cleanup, which will also free those buffers. This causes two warnings like the following, one for pi->sechdrs and the other for pi->purgatory_buf: kexec-bzImage64: Loading purgatory failed ------------[ cut here ]------------ WARNING: CPU: 1 PID: 2119 at mm/vmalloc.c:1490 __vunmap+0xc1/0xd0 Trying to vfree() nonexistent vm area (ffffc90000e91000) Modules linked in: CPU: 1 PID: 2119 Comm: kexec Not tainted 4.8.0-rc3+ #5 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 Call Trace: dump_stack+0x4d/0x65 __warn+0xcb/0xf0 warn_slowpath_fmt+0x4f/0x60 ? find_vmap_area+0x19/0x70 ? kimage_file_post_load_cleanup+0x47/0xb0 __vunmap+0xc1/0xd0 vfree+0x2e/0x70 kimage_file_post_load_cleanup+0x5e/0xb0 SyS_kexec_file_load+0x448/0x680 ? putname+0x54/0x60 ? do_sys_open+0x190/0x1f0 entry_SYSCALL_64_fastpath+0x13/0x8f ---[ end trace 158bb74f5950ca2b ]--- Fix by setting pi->sechdrs an pi->purgatory_buf to NULL, since vfree won't try to free a NULL pointer. Link: http://lkml.kernel.org/r/1472083546-23683-1-git-send-email-bauerman@linux.vnet.ibm.com Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com> Acked-by: Baoquan He <bhe@redhat.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Dave Young <dyoung@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 420902c upstream. If we hold the superblock lock while calling reiserfs_quota_on_mount(), we can deadlock our own worker - mount blocks kworker/3:2, sleeps forever more. crash> ps|grep UN 715 2 3 ffff880220734d30 UN 0.0 0 0 [kworker/3:2] 9369 9341 2 ffff88021ffb7560 UN 1.3 493404 123184 Xorg 9665 9664 3 ffff880225b92ab0 UN 0.0 47368 812 udisks-daemon 10635 10403 3 ffff880222f22c70 UN 0.0 14904 936 mount crash> bt ffff880220734d30 PID: 715 TASK: ffff880220734d30 CPU: 3 COMMAND: "kworker/3:2" #0 [ffff8802244c3c20] schedule at ffffffff8144584b #1 [ffff8802244c3cc8] __rt_mutex_slowlock at ffffffff814472b3 #2 [ffff8802244c3d28] rt_mutex_slowlock at ffffffff814473f5 #3 [ffff8802244c3dc8] reiserfs_write_lock at ffffffffa05f28fd [reiserfs] #4 [ffff8802244c3de8] flush_async_commits at ffffffffa05ec91d [reiserfs] #5 [ffff8802244c3e08] process_one_work at ffffffff81073726 #6 [ffff8802244c3e68] worker_thread at ffffffff81073eba #7 [ffff8802244c3ec8] kthread at ffffffff810782e0 #8 [ffff8802244c3f48] kernel_thread_helper at ffffffff81450064 crash> rd ffff8802244c3cc8 10 ffff8802244c3cc8: ffffffff814472b3 ffff880222f23250 .rD.....P2.".... ffff8802244c3cd8: 0000000000000000 0000000000000286 ................ ffff8802244c3ce8: ffff8802244c3d30 ffff880220734d80 0=L$.....Ms .... ffff8802244c3cf8: ffff880222e8f628 0000000000000000 (.."............ ffff8802244c3d08: 0000000000000000 0000000000000002 ................ crash> struct rt_mutex ffff880222e8f628 struct rt_mutex { wait_lock = { raw_lock = { slock = 65537 } }, wait_list = { node_list = { next = 0xffff8802244c3d48, prev = 0xffff8802244c3d48 } }, owner = 0xffff880222f22c71, save_state = 0 } crash> bt 0xffff880222f22c70 PID: 10635 TASK: ffff880222f22c70 CPU: 3 COMMAND: "mount" #0 [ffff8802216a9868] schedule at ffffffff8144584b #1 [ffff8802216a9910] schedule_timeout at ffffffff81446865 #2 [ffff8802216a99a0] wait_for_common at ffffffff81445f74 #3 [ffff8802216a9a30] flush_work at ffffffff810712d3 #4 [ffff8802216a9ab0] schedule_on_each_cpu at ffffffff81074463 #5 [ffff8802216a9ae0] invalidate_bdev at ffffffff81178aba #6 [ffff8802216a9af0] vfs_load_quota_inode at ffffffff811a3632 #7 [ffff8802216a9b50] dquot_quota_on_mount at ffffffff811a375c #8 [ffff8802216a9b80] finish_unfinished at ffffffffa05dd8b0 [reiserfs] #9 [ffff8802216a9cc0] reiserfs_fill_super at ffffffffa05de825 [reiserfs] RIP: 00007f7b9303997a RSP: 00007ffff443c7a8 RFLAGS: 00010202 RAX: 00000000000000a5 RBX: ffffffff8144ef12 RCX: 00007f7b932e9ee0 RDX: 00007f7b93d9a400 RSI: 00007f7b93d9a3e0 RDI: 00007f7b93d9a3c0 RBP: 00007f7b93d9a2c0 R8: 00007f7b93d9a550 R9: 0000000000000001 R10: ffffffffc0ed040e R11: 0000000000000202 R12: 000000000000040e R13: 0000000000000000 R14: 00000000c0ed040e R15: 00007ffff443ca20 ORIG_RAX: 00000000000000a5 CS: 0033 SS: 002b Signed-off-by: Mike Galbraith <efault@gmx.de> Acked-by: Frederic Weisbecker <fweisbec@gmail.com> Acked-by: Mike Galbraith <mgalbraith@suse.de> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Tushar Dave says: ==================== sparc: Enable sun4v hypervisor PCI IOMMU v2 APIs and ATU ATU (Address Translation Unit) is a new IOMMU in SPARC supported with sun4v hypervisor PCI IOMMU v2 APIs. Current SPARC IOMMU supports only 32bit address ranges and one TSB per PCIe root complex that has a 2GB per root complex DVMA space limit. The limit has become a scalability bottleneck nowadays that a typical 10G/40G NIC can consume 500MB DVMA space per instance. When DVMA resource is exhausted, devices will not be usable since the driver can't allocate DVMA. For example, we recently experienced legacy IOMMU limitation while using i40e driver in system with large number of CPUs (e.g. 128). Four ports of i40e, each request 128 QP (Queue Pairs). Each queue has 512 (default) descriptors. So considering only RX queues (because RX premap DMA buffers), i40e takes 4*128*512 number of DMA entries in IOMMU table. Legacy IOMMU can have at max (2G/8K)- 1 entries available in table. So bringing up four instance of i40e alone saturate existing IOMMU resource. ATU removes bottleneck by allowing guest os to create IOTSB of size 32G (or more) with 64bit address ranges available in ATU HW. 32G is more than enough DVMA space to be shared by all PCIe devices under root complex contrast to 2G space provided by legacy IOMMU. ATU allows PCIe devices to use 64bit DMA addressing. Devices which choose to use 32bit DMA mask will continue to work with the existing legacy IOMMU. The patch set is tested on sun4v (T1000, T2000, T3, T4, T5, T7, S7) and sun4u SPARC. Thanks. -Tushar v2->v3: - Patch openbmc#5 addresses comment by Joe Perches. -- use %s, __func__ instead of embedding the function name. v1->v2: - Patch openbmc#2 addresses comments by Dave M. -- use page allocator to allocate IOTSB. -- use true/false with boolean variables. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>

We cannot do printk() from tk_debug_account_sleep_time(), because tk_debug_account_sleep_time() is called under tk_core seq lock. The reason why printk() is unsafe there is that console_sem may invoke scheduler (up()->wake_up_process()->activate_task()), which, in turn, can return back to timekeeping code, for instance, via get_time()->ktime_get(), deadlocking the system on tk_core seq lock. [ 48.950592] ====================================================== [ 48.950622] [ INFO: possible circular locking dependency detected ] [ 48.950622] 4.10.0-rc7-next-20170213+ openbmc#101 Not tainted [ 48.950622] ------------------------------------------------------- [ 48.950622] kworker/0:0/3 is trying to acquire lock: [ 48.950653] (tk_core){----..}, at: [<c01cc624>] retrigger_next_event+0x4c/0x90 [ 48.950683] but task is already holding lock: [ 48.950683] (hrtimer_bases.lock){-.-...}, at: [<c01cc610>] retrigger_next_event+0x38/0x90 [ 48.950714] which lock already depends on the new lock. [ 48.950714] the existing dependency chain (in reverse order) is: [ 48.950714] -> openbmc#5 (hrtimer_bases.lock){-.-...}: [ 48.950744] _raw_spin_lock_irqsave+0x50/0x64 [ 48.950775] lock_hrtimer_base+0x28/0x58 [ 48.950775] hrtimer_start_range_ns+0x20/0x5c8 [ 48.950775] __enqueue_rt_entity+0x320/0x360 [ 48.950805] enqueue_rt_entity+0x2c/0x44 [ 48.950805] enqueue_task_rt+0x24/0x94 [ 48.950836] ttwu_do_activate+0x54/0xc0 [ 48.950836] try_to_wake_up+0x248/0x5c8 [ 48.950836] __setup_irq+0x420/0x5f0 [ 48.950836] request_threaded_irq+0xdc/0x184 [ 48.950866] devm_request_threaded_irq+0x58/0xa4 [ 48.950866] omap_i2c_probe+0x530/0x6a0 [ 48.950897] platform_drv_probe+0x50/0xb0 [ 48.950897] driver_probe_device+0x1f8/0x2cc [ 48.950897] __driver_attach+0xc0/0xc4 [ 48.950927] bus_for_each_dev+0x6c/0xa0 [ 48.950927] bus_add_driver+0x100/0x210 [ 48.950927] driver_register+0x78/0xf4 [ 48.950958] do_one_initcall+0x3c/0x16c [ 48.950958] kernel_init_freeable+0x20c/0x2d8 [ 48.950958] kernel_init+0x8/0x110 [ 48.950988] ret_from_fork+0x14/0x24 [ 48.950988] -> openbmc#4 (&rt_b->rt_runtime_lock){-.-...}: [ 48.951019] _raw_spin_lock+0x40/0x50 [ 48.951019] rq_offline_rt+0x9c/0x2bc [ 48.951019] set_rq_offline.part.2+0x2c/0x58 [ 48.951049] rq_attach_root+0x134/0x144 [ 48.951049] cpu_attach_domain+0x18c/0x6f4 [ 48.951049] build_sched_domains+0xba4/0xd80 [ 48.951080] sched_init_smp+0x68/0x10c [ 48.951080] kernel_init_freeable+0x160/0x2d8 [ 48.951080] kernel_init+0x8/0x110 [ 48.951080] ret_from_fork+0x14/0x24 [ 48.951110] -> openbmc#3 (&rq->lock){-.-.-.}: [ 48.951110] _raw_spin_lock+0x40/0x50 [ 48.951141] task_fork_fair+0x30/0x124 [ 48.951141] sched_fork+0x194/0x2e0 [ 48.951141] copy_process.part.5+0x448/0x1a20 [ 48.951171] _do_fork+0x98/0x7e8 [ 48.951171] kernel_thread+0x2c/0x34 [ 48.951171] rest_init+0x1c/0x18c [ 48.951202] start_kernel+0x35c/0x3d4 [ 48.951202] 0x8000807c [ 48.951202] -> openbmc#2 (&p->pi_lock){-.-.-.}: [ 48.951232] _raw_spin_lock_irqsave+0x50/0x64 [ 48.951232] try_to_wake_up+0x30/0x5c8 [ 48.951232] up+0x4c/0x60 [ 48.951263] __up_console_sem+0x2c/0x58 [ 48.951263] console_unlock+0x3b4/0x650 [ 48.951263] vprintk_emit+0x270/0x474 [ 48.951293] vprintk_default+0x20/0x28 [ 48.951293] printk+0x20/0x30 [ 48.951324] kauditd_hold_skb+0x94/0xb8 [ 48.951324] kauditd_thread+0x1a4/0x56c [ 48.951324] kthread+0x104/0x148 [ 48.951354] ret_from_fork+0x14/0x24 [ 48.951354] -> openbmc#1 ((console_sem).lock){-.....}: [ 48.951385] _raw_spin_lock_irqsave+0x50/0x64 [ 48.951385] down_trylock+0xc/0x2c [ 48.951385] __down_trylock_console_sem+0x24/0x80 [ 48.951385] console_trylock+0x10/0x8c [ 48.951416] vprintk_emit+0x264/0x474 [ 48.951416] vprintk_default+0x20/0x28 [ 48.951416] printk+0x20/0x30 [ 48.951446] tk_debug_account_sleep_time+0x5c/0x70 [ 48.951446] __timekeeping_inject_sleeptime.constprop.3+0x170/0x1a0 [ 48.951446] timekeeping_resume+0x218/0x23c [ 48.951477] syscore_resume+0x94/0x42c [ 48.951477] suspend_enter+0x554/0x9b4 [ 48.951477] suspend_devices_and_enter+0xd8/0x4b4 [ 48.951507] enter_state+0x934/0xbd4 [ 48.951507] pm_suspend+0x14/0x70 [ 48.951507] state_store+0x68/0xc8 [ 48.951538] kernfs_fop_write+0xf4/0x1f8 [ 48.951538] __vfs_write+0x1c/0x114 [ 48.951538] vfs_write+0xa0/0x168 [ 48.951568] SyS_write+0x3c/0x90 [ 48.951568] __sys_trace_return+0x0/0x10 [ 48.951568] -> #0 (tk_core){----..}: [ 48.951599] lock_acquire+0xe0/0x294 [ 48.951599] ktime_get_update_offsets_now+0x5c/0x1d4 [ 48.951629] retrigger_next_event+0x4c/0x90 [ 48.951629] on_each_cpu+0x40/0x7c [ 48.951629] clock_was_set_work+0x14/0x20 [ 48.951660] process_one_work+0x2b4/0x808 [ 48.951660] worker_thread+0x3c/0x550 [ 48.951660] kthread+0x104/0x148 [ 48.951690] ret_from_fork+0x14/0x24 [ 48.951690] other info that might help us debug this: [ 48.951690] Chain exists of: tk_core --> &rt_b->rt_runtime_lock --> hrtimer_bases.lock [ 48.951721] Possible unsafe locking scenario: [ 48.951721] CPU0 CPU1 [ 48.951721] ---- ---- [ 48.951721] lock(hrtimer_bases.lock); [ 48.951751] lock(&rt_b->rt_runtime_lock); [ 48.951751] lock(hrtimer_bases.lock); [ 48.951751] lock(tk_core); [ 48.951782] *** DEADLOCK *** [ 48.951782] 3 locks held by kworker/0:0/3: [ 48.951782] #0: ("events"){.+.+.+}, at: [<c0156590>] process_one_work+0x1f8/0x808 [ 48.951812] openbmc#1: (hrtimer_work){+.+...}, at: [<c0156590>] process_one_work+0x1f8/0x808 [ 48.951843] openbmc#2: (hrtimer_bases.lock){-.-...}, at: [<c01cc610>] retrigger_next_event+0x38/0x90 [ 48.951843] stack backtrace: [ 48.951873] CPU: 0 PID: 3 Comm: kworker/0:0 Not tainted 4.10.0-rc7-next-20170213+ [ 48.951904] Workqueue: events clock_was_set_work [ 48.951904] [<c0110208>] (unwind_backtrace) from [<c010c224>] (show_stack+0x10/0x14) [ 48.951934] [<c010c224>] (show_stack) from [<c04ca6c0>] (dump_stack+0xac/0xe0) [ 48.951934] [<c04ca6c0>] (dump_stack) from [<c019b5cc>] (print_circular_bug+0x1d0/0x308) [ 48.951965] [<c019b5cc>] (print_circular_bug) from [<c019d2a8>] (validate_chain+0xf50/0x1324) [ 48.951965] [<c019d2a8>] (validate_chain) from [<c019ec18>] (__lock_acquire+0x468/0x7e8) [ 48.951995] [<c019ec18>] (__lock_acquire) from [<c019f634>] (lock_acquire+0xe0/0x294) [ 48.951995] [<c019f634>] (lock_acquire) from [<c01d0ea0>] (ktime_get_update_offsets_now+0x5c/0x1d4) [ 48.952026] [<c01d0ea0>] (ktime_get_update_offsets_now) from [<c01cc624>] (retrigger_next_event+0x4c/0x90) [ 48.952026] [<c01cc624>] (retrigger_next_event) from [<c01e4e24>] (on_each_cpu+0x40/0x7c) [ 48.952056] [<c01e4e24>] (on_each_cpu) from [<c01cafc4>] (clock_was_set_work+0x14/0x20) [ 48.952056] [<c01cafc4>] (clock_was_set_work) from [<c015664c>] (process_one_work+0x2b4/0x808) [ 48.952087] [<c015664c>] (process_one_work) from [<c0157774>] (worker_thread+0x3c/0x550) [ 48.952087] [<c0157774>] (worker_thread) from [<c015d644>] (kthread+0x104/0x148) [ 48.952087] [<c015d644>] (kthread) from [<c0107830>] (ret_from_fork+0x14/0x24) Replace printk() with printk_deferred(), which does not call into the scheduler. Fixes: 0bf43f1 ("timekeeping: Prints the amounts of time spent during suspend") Reported-and-tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Petr Mladek <pmladek@suse.com> Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: "Rafael J . Wysocki" <rjw@rjwysocki.net> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: John Stultz <john.stultz@linaro.org> Cc: "[4.9+]" <stable@vger.kernel.org> Link: http://lkml.kernel.org/r/20170215044332.30449-1-sergey.senozhatsky@gmail.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

'perf annotate' is dropping the cr* fields from branch instructions. Fix it by adding support to display branch instructions having multiple operands. Power Arch objdump of int_sqrt: 20.36 | c0000000004d2694: subf r10,r10,r3 | c0000000004d2698: v bgt cr6,c0000000004d26a0 <int_sqrt+0x40> 1.82 | c0000000004d269c: mr r3,r10 29.18 | c0000000004d26a0: mr r10,r8 | c0000000004d26a4: v bgt cr7,c0000000004d26ac <int_sqrt+0x4c> | c0000000004d26a8: mr r10,r7 Power Arch Before Patch: 20.36 | subf r10,r10,r3 | v bgt 40 1.82 | mr r3,r10 29.18 | 40: mr r10,r8 | v bgt 4c | mr r10,r7 Power Arch After patch: 20.36 | subf r10,r10,r3 | v bgt cr6,40 1.82 | mr r3,r10 29.18 | 40: mr r10,r8 | v bgt cr7,4c | mr r10,r7 Also support AArch64 conditional branch instructions, which can have up to three operands: Aarch64 Non-simplified (raw objdump) view: │ffff0000083cd11c: ↑ cbz w0, ffff0000083cd100 <security_fil▒ ... 4.44 │ffff000│083cd134: ↓ tbnz w0, openbmc#26, ffff0000083cd190 <securit▒ ... 1.37 │ffff000│083cd144: ↓ tbnz w22, openbmc#5, ffff0000083cd1a4 <securit▒ │ffff000│083cd148: mov w19, #0x20000 //▒ 1.02 │ffff000│083cd14c: ↓ tbz w22, openbmc#2, ffff0000083cd1ac <securit▒ ... 0.68 │ffff000└──3cd16c: ↑ cbnz w0, ffff0000083cd120 <security_fil▒ Aarch64 Simplified, before this patch: │ ↑ cbz 40 ... 4.44 │ │↓ tbnz w0, openbmc#26, ffff0000083cd190 <security_file_permiss▒ ... 1.37 │ │↓ tbnz w22, openbmc#5, ffff0000083cd1a4 <security_file_permiss▒ │ │ mov w19, #0x20000 // #131072 1.02 │ │↓ tbz w22, openbmc#2, ffff0000083cd1ac <security_file_permiss▒ ... 0.68 │ └──cbnz 60 the cbz operand is missing, and the tbz doesn't get simplified processing at all because the parsing function failed to match an address. Aarch64 Simplified, After this patch applied: │ ↑ cbz w0, 40 ... 4.44 │ │↓ tbnz w0, openbmc#26, d0 ... 1.37 │ │↓ tbnz w22, openbmc#5, e4 │ │ mov w19, #0x20000 // #131072 1.02 │ │↓ tbz w22, openbmc#2, ec ... 0.68 │ └──cbnz w0, 60 Originally-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com> Tested-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com> Reported-by: Anton Blanchard <anton@samba.org> Reported-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Kim Phillips <kim.phillips@arm.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Taeung Song <treeze.taeung@gmail.com> Link: http://lkml.kernel.org/r/20170601092959.f60d98912e8a1b66fd1e4c0e@arm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

commit be346c1 upstream. The code in ocfs2_dio_end_io_write() estimates number of necessary transaction credits using ocfs2_calc_extend_credits(). This however does not take into account that the IO could be arbitrarily large and can contain arbitrary number of extents. Extent tree manipulations do often extend the current transaction but not in all of the cases. For example if we have only single block extents in the tree, ocfs2_mark_extent_written() will end up calling ocfs2_replace_extent_rec() all the time and we will never extend the current transaction and eventually exhaust all the transaction credits if the IO contains many single block extents. Once that happens a WARN_ON(jbd2_handle_buffer_credits(handle) <= 0) is triggered in jbd2_journal_dirty_metadata() and subsequently OCFS2 aborts in response to this error. This was actually triggered by one of our customers on a heavily fragmented OCFS2 filesystem. To fix the issue make sure the transaction always has enough credits for one extent insert before each call of ocfs2_mark_extent_written(). Heming Zhao said: ------ PANIC: "Kernel panic - not syncing: OCFS2: (device dm-1): panic forced after error" PID: xxx TASK: xxxx CPU: 5 COMMAND: "SubmitThread-CA" #0 machine_kexec at ffffffff8c069932 #1 __crash_kexec at ffffffff8c1338fa #2 panic at ffffffff8c1d69b9 #3 ocfs2_handle_error at ffffffffc0c86c0c [ocfs2] #4 __ocfs2_abort at ffffffffc0c88387 [ocfs2] #5 ocfs2_journal_dirty at ffffffffc0c51e98 [ocfs2] #6 ocfs2_split_extent at ffffffffc0c27ea3 [ocfs2] #7 ocfs2_change_extent_flag at ffffffffc0c28053 [ocfs2] #8 ocfs2_mark_extent_written at ffffffffc0c28347 [ocfs2] #9 ocfs2_dio_end_io_write at ffffffffc0c2bef9 [ocfs2] #10 ocfs2_dio_end_io at ffffffffc0c2c0f5 [ocfs2] #11 dio_complete at ffffffff8c2b9fa7 #12 do_blockdev_direct_IO at ffffffff8c2bc09f #13 ocfs2_direct_IO at ffffffffc0c2b653 [ocfs2] #14 generic_file_direct_write at ffffffff8c1dcf14 #15 __generic_file_write_iter at ffffffff8c1dd07b #16 ocfs2_file_write_iter at ffffffffc0c49f1f [ocfs2] #17 aio_write at ffffffff8c2cc72e #18 kmem_cache_alloc at ffffffff8c248dde #19 do_io_submit at ffffffff8c2ccada #20 do_syscall_64 at ffffffff8c004984 #21 entry_SYSCALL_64_after_hwframe at ffffffff8c8000ba Link: https://lkml.kernel.org/r/20240617095543.6971-1-jack@suse.cz Link: https://lkml.kernel.org/r/20240614145243.8837-1-jack@suse.cz Fixes: c15471f ("ocfs2: fix sparse file & data ordering issue in direct io") Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Reviewed-by: Heming Zhao <heming.zhao@suse.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 3b3b84a ] As reported by Jose E. Marchesi in off-list discussion, GCC and LLVM generate slightly different code for dummy_st_ops_success/test_1(): SEC("struct_ops/test_1") int BPF_PROG(test_1, struct bpf_dummy_ops_state *state) { int ret; if (!state) return 0xf2f3f4f5; ret = state->val; state->val = 0x5a; return ret; } GCC-generated LLVM-generated ---------------------------- --------------------------- 0: r1 = *(u64 *)(r1 + 0x0) 0: w0 = -0xd0c0b0b 1: if r1 == 0x0 goto 5f 1: r1 = *(u64 *)(r1 + 0x0) 2: r0 = *(s32 *)(r1 + 0x0) 2: if r1 == 0x0 goto 6f 3: *(u32 *)(r1 + 0x0) = 0x5a 3: r0 = *(u32 *)(r1 + 0x0) 4: exit 4: w2 = 0x5a 5: r0 = -0xd0c0b0b 5: *(u32 *)(r1 + 0x0) = r2 6: exit 6: exit If the 'state' argument is not marked as nullable in net/bpf/bpf_dummy_struct_ops.c, the verifier would assume that 'r1 == 0x0' is never true: - for the GCC version, this means that instructions #5-6 would be marked as dead and removed; - for the LLVM version, all instructions would be marked as live. The test dummy_st_ops/dummy_init_ret_value actually sets the 'state' parameter to NULL. Therefore, when the 'state' argument is not marked as nullable, the GCC-generated version of the code would trigger a NULL pointer dereference at instruction #3. This patch updates the test_1() test case to always follow a shape similar to the GCC-generated version above, in order to verify whether the 'state' nullability is marked correctly. Reported-by: Jose E. Marchesi <jemarch@gnu.org> Signed-off-by: Eduard Zingerman <eddyz87@gmail.com> Link: https://lore.kernel.org/r/20240424012821.595216-3-eddyz87@gmail.com Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

… __netif_rx() [ Upstream commit e15a5d8 ] The following is emitted when using idxd (DSA) dmanegine as the data mover for ntb_transport that ntb_netdev uses. [74412.546922] BUG: using smp_processor_id() in preemptible [00000000] code: irq/52-idxd-por/14526 [74412.556784] caller is netif_rx_internal+0x42/0x130 [74412.562282] CPU: 6 PID: 14526 Comm: irq/52-idxd-por Not tainted 6.9.5 #5 [74412.569870] Hardware name: Intel Corporation ArcherCity/ArcherCity, BIOS EGSDCRB1.E9I.1752.P05.2402080856 02/08/2024 [74412.581699] Call Trace: [74412.584514] <TASK> [74412.586933] dump_stack_lvl+0x55/0x70 [74412.591129] check_preemption_disabled+0xc8/0xf0 [74412.596374] netif_rx_internal+0x42/0x130 [74412.600957] __netif_rx+0x20/0xd0 [74412.604743] ntb_netdev_rx_handler+0x66/0x150 [ntb_netdev] [74412.610985] ntb_complete_rxc+0xed/0x140 [ntb_transport] [74412.617010] ntb_rx_copy_callback+0x53/0x80 [ntb_transport] [74412.623332] idxd_dma_complete_txd+0xe3/0x160 [idxd] [74412.628963] idxd_wq_thread+0x1a6/0x2b0 [idxd] [74412.634046] irq_thread_fn+0x21/0x60 [74412.638134] ? irq_thread+0xa8/0x290 [74412.642218] irq_thread+0x1a0/0x290 [74412.646212] ? __pfx_irq_thread_fn+0x10/0x10 [74412.651071] ? __pfx_irq_thread_dtor+0x10/0x10 [74412.656117] ? __pfx_irq_thread+0x10/0x10 [74412.660686] kthread+0x100/0x130 [74412.664384] ? __pfx_kthread+0x10/0x10 [74412.668639] ret_from_fork+0x31/0x50 [74412.672716] ? __pfx_kthread+0x10/0x10 [74412.676978] ret_from_fork_asm+0x1a/0x30 [74412.681457] </TASK> The cause is due to the idxd driver interrupt completion handler uses threaded interrupt and the threaded handler is not hard or soft interrupt context. However __netif_rx() can only be called from interrupt context. Change the call to netif_rx() in order to allow completion via normal context for dmaengine drivers that utilize threaded irq handling. While the following commit changed from netif_rx() to __netif_rx(), baebdf4 ("net: dev: Makes sure netif_rx() can be invoked in any context."), the change should've been a noop instead. However, the code precedes this fix should've been using netif_rx_ni() or netif_rx_any_context(). Fixes: 548c237 ("net: Add support for NTB virtual ethernet device") Reported-by: Jerry Dai <jerry.dai@intel.com> Tested-by: Jerry Dai <jerry.dai@intel.com> Signed-off-by: Dave Jiang <dave.jiang@intel.com> Link: https://patch.msgid.link/20240701181538.3799546-1-dave.jiang@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 86a41ea ] When l2tp tunnels use a socket provided by userspace, we can hit lockdep splats like the below when data is transmitted through another (unrelated) userspace socket which then gets routed over l2tp. This issue was previously discussed here: https://lore.kernel.org/netdev/87sfialu2n.fsf@cloudflare.com/ The solution is to have lockdep treat socket locks of l2tp tunnel sockets separately than those of standard INET sockets. To do so, use a different lockdep subclass where lock nesting is possible. ============================================ WARNING: possible recursive locking detected 6.10.0+ #34 Not tainted -------------------------------------------- iperf3/771 is trying to acquire lock: ffff8881027601d8 (slock-AF_INET/1){+.-.}-{2:2}, at: l2tp_xmit_skb+0x243/0x9d0 but task is already holding lock: ffff888102650d98 (slock-AF_INET/1){+.-.}-{2:2}, at: tcp_v4_rcv+0x1848/0x1e10 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(slock-AF_INET/1); lock(slock-AF_INET/1); *** DEADLOCK *** May be due to missing lock nesting notation 10 locks held by iperf3/771: #0: ffff888102650258 (sk_lock-AF_INET){+.+.}-{0:0}, at: tcp_sendmsg+0x1a/0x40 #1: ffffffff822ac220 (rcu_read_lock){....}-{1:2}, at: __ip_queue_xmit+0x4b/0xbc0 #2: ffffffff822ac220 (rcu_read_lock){....}-{1:2}, at: ip_finish_output2+0x17a/0x1130 #3: ffffffff822ac220 (rcu_read_lock){....}-{1:2}, at: process_backlog+0x28b/0x9f0 #4: ffffffff822ac220 (rcu_read_lock){....}-{1:2}, at: ip_local_deliver_finish+0xf9/0x260 #5: ffff888102650d98 (slock-AF_INET/1){+.-.}-{2:2}, at: tcp_v4_rcv+0x1848/0x1e10 #6: ffffffff822ac220 (rcu_read_lock){....}-{1:2}, at: __ip_queue_xmit+0x4b/0xbc0 #7: ffffffff822ac220 (rcu_read_lock){....}-{1:2}, at: ip_finish_output2+0x17a/0x1130 #8: ffffffff822ac1e0 (rcu_read_lock_bh){....}-{1:2}, at: __dev_queue_xmit+0xcc/0x1450 #9: ffff888101f33258 (dev->qdisc_tx_busylock ?: &qdisc_tx_busylock#2){+...}-{2:2}, at: __dev_queue_xmit+0x513/0x1450 stack backtrace: CPU: 2 UID: 0 PID: 771 Comm: iperf3 Not tainted 6.10.0+ #34 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 Call Trace: <IRQ> dump_stack_lvl+0x69/0xa0 dump_stack+0xc/0x20 __lock_acquire+0x135d/0x2600 ? srso_alias_return_thunk+0x5/0xfbef5 lock_acquire+0xc4/0x2a0 ? l2tp_xmit_skb+0x243/0x9d0 ? __skb_checksum+0xa3/0x540 _raw_spin_lock_nested+0x35/0x50 ? l2tp_xmit_skb+0x243/0x9d0 l2tp_xmit_skb+0x243/0x9d0 l2tp_eth_dev_xmit+0x3c/0xc0 dev_hard_start_xmit+0x11e/0x420 sch_direct_xmit+0xc3/0x640 __dev_queue_xmit+0x61c/0x1450 ? ip_finish_output2+0xf4c/0x1130 ip_finish_output2+0x6b6/0x1130 ? srso_alias_return_thunk+0x5/0xfbef5 ? __ip_finish_output+0x217/0x380 ? srso_alias_return_thunk+0x5/0xfbef5 __ip_finish_output+0x217/0x380 ip_output+0x99/0x120 __ip_queue_xmit+0xae4/0xbc0 ? srso_alias_return_thunk+0x5/0xfbef5 ? srso_alias_return_thunk+0x5/0xfbef5 ? tcp_options_write.constprop.0+0xcb/0x3e0 ip_queue_xmit+0x34/0x40 __tcp_transmit_skb+0x1625/0x1890 __tcp_send_ack+0x1b8/0x340 tcp_send_ack+0x23/0x30 __tcp_ack_snd_check+0xa8/0x530 ? srso_alias_return_thunk+0x5/0xfbef5 tcp_rcv_established+0x412/0xd70 tcp_v4_do_rcv+0x299/0x420 tcp_v4_rcv+0x1991/0x1e10 ip_protocol_deliver_rcu+0x50/0x220 ip_local_deliver_finish+0x158/0x260 ip_local_deliver+0xc8/0xe0 ip_rcv+0xe5/0x1d0 ? __pfx_ip_rcv+0x10/0x10 __netif_receive_skb_one_core+0xce/0xe0 ? process_backlog+0x28b/0x9f0 __netif_receive_skb+0x34/0xd0 ? process_backlog+0x28b/0x9f0 process_backlog+0x2cb/0x9f0 __napi_poll.constprop.0+0x61/0x280 net_rx_action+0x332/0x670 ? srso_alias_return_thunk+0x5/0xfbef5 ? find_held_lock+0x2b/0x80 ? srso_alias_return_thunk+0x5/0xfbef5 ? srso_alias_return_thunk+0x5/0xfbef5 handle_softirqs+0xda/0x480 ? __dev_queue_xmit+0xa2c/0x1450 do_softirq+0xa1/0xd0 </IRQ> <TASK> __local_bh_enable_ip+0xc8/0xe0 ? __dev_queue_xmit+0xa2c/0x1450 __dev_queue_xmit+0xa48/0x1450 ? ip_finish_output2+0xf4c/0x1130 ip_finish_output2+0x6b6/0x1130 ? srso_alias_return_thunk+0x5/0xfbef5 ? __ip_finish_output+0x217/0x380 ? srso_alias_return_thunk+0x5/0xfbef5 __ip_finish_output+0x217/0x380 ip_output+0x99/0x120 __ip_queue_xmit+0xae4/0xbc0 ? srso_alias_return_thunk+0x5/0xfbef5 ? srso_alias_return_thunk+0x5/0xfbef5 ? tcp_options_write.constprop.0+0xcb/0x3e0 ip_queue_xmit+0x34/0x40 __tcp_transmit_skb+0x1625/0x1890 tcp_write_xmit+0x766/0x2fb0 ? __entry_text_end+0x102ba9/0x102bad ? srso_alias_return_thunk+0x5/0xfbef5 ? __might_fault+0x74/0xc0 ? srso_alias_return_thunk+0x5/0xfbef5 __tcp_push_pending_frames+0x56/0x190 tcp_push+0x117/0x310 tcp_sendmsg_locked+0x14c1/0x1740 tcp_sendmsg+0x28/0x40 inet_sendmsg+0x5d/0x90 sock_write_iter+0x242/0x2b0 vfs_write+0x68d/0x800 ? __pfx_sock_write_iter+0x10/0x10 ksys_write+0xc8/0xf0 __x64_sys_write+0x3d/0x50 x64_sys_call+0xfaf/0x1f50 do_syscall_64+0x6d/0x140 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7f4d143af992 Code: c3 8b 07 85 c0 75 24 49 89 fb 48 89 f0 48 89 d7 48 89 ce 4c 89 c2 4d 89 ca 4c 8b 44 24 08 4c 8b 4c 24 10 4c 89 5c 24 08 0f 05 <c3> e9 01 cc ff ff 41 54 b8 02 00 00 0 RSP: 002b:00007ffd65032058 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 RAX: ffffffffffffffda RBX: 0000000000000001 RCX: 00007f4d143af992 RDX: 0000000000000025 RSI: 00007f4d143f3bcc RDI: 0000000000000005 RBP: 00007f4d143f2b28 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00007f4d143f3bcc R13: 0000000000000005 R14: 0000000000000000 R15: 00007ffd650323f0 </TASK> Fixes: 0b2c597 ("l2tp: close all race conditions in l2tp_tunnel_register()") Suggested-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot+6acef9e0a4d1f46c83d4@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=6acef9e0a4d1f46c83d4 CC: gnault@redhat.com CC: cong.wang@bytedance.com Signed-off-by: James Chapman <jchapman@katalix.com> Signed-off-by: Tom Parkin <tparkin@katalix.com> Link: https://patch.msgid.link/20240806160626.1248317-1-jchapman@katalix.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

Daniel Machon says: ==================== net: lan966x: use the newly introduced FDMA library This patch series is the second of a 2-part series [1], that adds a new common FDMA library for Microchip switch chips Sparx5 and lan966x. These chips share the same FDMA engine, and as such will benefit from a common library with a common implementation. This also has the benefit of removing a lot of open-coded bookkeeping and duplicate code for the two drivers. In this second series, the FDMA library will be taken into use by the lan966x switch driver. ################### # Example of use: # ################### - Initialize the rx and tx fdma structs with values for: number of DCB's, number of DB's, channel ID, DB size (data buffer size), and total size of the requested memory. Also provide two callbacks: nextptr_cb() and dataptr_cb() for getting the nextptr and dataptr. - Allocate memory using fdma_alloc_phys() or fdma_alloc_coherent(). - Initialize the DCB's with fdma_dcb_init(). - Add new DCB's with fdma_dcb_add(). - Free memory with fdma_free_phys() or fdma_free_coherent(). ##################### # Patch breakdown: # ##################### Patch openbmc#1: select FDMA library for lan966x. Patch openbmc#2: includes the fdma_api.h header and removes old symbols. Patch openbmc#3: replaces old rx and tx variables with equivalent ones from the fdma struct. Only the variables that can be changed without breaking traffic is changed in this patch. Patch openbmc#4: uses the library for allocation of rx buffers. This requires quite a bit of refactoring in this single patch. Patch openbmc#5: uses the library for adding DCB's in the rx path. Patch openbmc#6: uses the library for freeing rx buffers. Patch openbmc#7: uses the library for allocation of tx buffers. This requires quite a bit of refactoring in this single patch. Patch openbmc#8: uses the library for adding DCB's in the tx path. Patch openbmc#9: uses the library helpers in the tx path. Patch openbmc#10: ditch last_in_use variable and use library instead. Patch openbmc#11: uses library helpers throughout. Patch openbmc#12: refactor lan966x_fdma_reload() function. [1] https://lore.kernel.org/netdev/20240902-fdma-sparx5-v1-0-1e7d5e5a9f34@microchip.com/ Signed-off-by: Daniel Machon <daniel.machon@microchip.com> ==================== Link: https://patch.msgid.link/20240905-fdma-lan966x-v1-0-e083f8620165@microchip.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Ido Schimmel says: ==================== net: fib_rules: Add DSCP selector support Currently, the kernel rejects IPv4 FIB rules that try to match on the upper three DSCP bits: # ip -4 rule add tos 0x1c table 100 # ip -4 rule add tos 0x3c table 100 Error: Invalid tos. The reason for that is that historically users of the FIB lookup API only populated the lower three DSCP bits in the TOS field of the IPv4 flow key ('flowi4_tos'), which fits the TOS definition from the initial IPv4 specification (RFC 791). This is not very useful nowadays and instead some users want to be able to match on the six bits DSCP field, which replaced the TOS and IP precedence fields over 25 years ago (RFC 2474). In addition, the current behavior differs between IPv4 and IPv6 which does allow users to match on the entire DSCP field using the TOS selector. Recent patchsets made sure that callers of the FIB lookup API now populate the entire DSCP field in the IPv4 flow key. Therefore, it is now possible to extend FIB rules to match on DSCP. This is done by adding a new DSCP attribute which is implemented for both IPv4 and IPv6 to provide user space programs a consistent behavior between both address families. The behavior of the old TOS selector is unchanged and IPv4 FIB rules using it will only match on the lower three DSCP bits. The kernel will reject rules that try to use both selectors. Patch openbmc#1 adds the new DSCP attribute but rejects its usage. Patches openbmc#2-openbmc#3 implement IPv4 and IPv6 support. Patch openbmc#4 allows user space to use the new attribute. Patches openbmc#5-openbmc#6 add selftests. ==================== Link: https://patch.msgid.link/20240911093748.3662015-1-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The fields in the hist_entry are filled on-demand which means they only have meaningful values when relevant sort keys are used. So if neither of 'dso' nor 'sym' sort keys are used, the map/symbols in the hist entry can be garbage. So it shouldn't access it unconditionally. I got a segfault, when I wanted to see cgroup profiles. $ sudo perf record -a --all-cgroups --synth=cgroup true $ sudo perf report -s cgroup Program received signal SIGSEGV, Segmentation fault. 0x00005555557a8d90 in map__dso (map=0x0) at util/map.h:48 48 return RC_CHK_ACCESS(map)->dso; (gdb) bt #0 0x00005555557a8d90 in map__dso (map=0x0) at util/map.h:48 openbmc#1 0x00005555557aa39b in map__load (map=0x0) at util/map.c:344 openbmc#2 0x00005555557aa592 in map__find_symbol (map=0x0, addr=140736115941088) at util/map.c:385 openbmc#3 0x00005555557ef000 in hists__findnew_entry (hists=0x555556039d60, entry=0x7fffffffa4c0, al=0x7fffffffa8c0, sample_self=true) at util/hist.c:644 openbmc#4 0x00005555557ef61c in __hists__add_entry (hists=0x555556039d60, al=0x7fffffffa8c0, sym_parent=0x0, bi=0x0, mi=0x0, ki=0x0, block_info=0x0, sample=0x7fffffffaa90, sample_self=true, ops=0x0) at util/hist.c:761 openbmc#5 0x00005555557ef71f in hists__add_entry (hists=0x555556039d60, al=0x7fffffffa8c0, sym_parent=0x0, bi=0x0, mi=0x0, ki=0x0, sample=0x7fffffffaa90, sample_self=true) at util/hist.c:779 openbmc#6 0x00005555557f00fb in iter_add_single_normal_entry (iter=0x7fffffffa900, al=0x7fffffffa8c0) at util/hist.c:1015 openbmc#7 0x00005555557f09a7 in hist_entry_iter__add (iter=0x7fffffffa900, al=0x7fffffffa8c0, max_stack_depth=127, arg=0x7fffffffbce0) at util/hist.c:1260 openbmc#8 0x00005555555ba7ce in process_sample_event (tool=0x7fffffffbce0, event=0x7ffff7c14128, sample=0x7fffffffaa90, evsel=0x555556039ad0, machine=0x5555560388e8) at builtin-report.c:334 openbmc#9 0x00005555557b30c8 in evlist__deliver_sample (evlist=0x555556039010, tool=0x7fffffffbce0, event=0x7ffff7c14128, sample=0x7fffffffaa90, evsel=0x555556039ad0, machine=0x5555560388e8) at util/session.c:1232 openbmc#10 0x00005555557b32bc in machines__deliver_event (machines=0x5555560388e8, evlist=0x555556039010, event=0x7ffff7c14128, sample=0x7fffffffaa90, tool=0x7fffffffbce0, file_offset=110888, file_path=0x555556038ff0 "perf.data") at util/session.c:1271 openbmc#11 0x00005555557b3848 in perf_session__deliver_event (session=0x5555560386d0, event=0x7ffff7c14128, tool=0x7fffffffbce0, file_offset=110888, file_path=0x555556038ff0 "perf.data") at util/session.c:1354 openbmc#12 0x00005555557affaf in ordered_events__deliver_event (oe=0x555556038e60, event=0x555556135aa0) at util/session.c:132 openbmc#13 0x00005555557bb605 in do_flush (oe=0x555556038e60, show_progress=false) at util/ordered-events.c:245 openbmc#14 0x00005555557bb95c in __ordered_events__flush (oe=0x555556038e60, how=OE_FLUSH__ROUND, timestamp=0) at util/ordered-events.c:324 openbmc#15 0x00005555557bba46 in ordered_events__flush (oe=0x555556038e60, how=OE_FLUSH__ROUND) at util/ordered-events.c:342 openbmc#16 0x00005555557b1b3b in perf_event__process_finished_round (tool=0x7fffffffbce0, event=0x7ffff7c15bb8, oe=0x555556038e60) at util/session.c:780 openbmc#17 0x00005555557b3b27 in perf_session__process_user_event (session=0x5555560386d0, event=0x7ffff7c15bb8, file_offset=117688, file_path=0x555556038ff0 "perf.data") at util/session.c:1406 As you can see the entry->ms.map was NULL even if he->ms.map has a value. This is because 'sym' sort key is not given, so it cannot assume whether he->ms.sym and entry->ms.sym is the same. I only checked the 'sym' sort key here as it implies 'dso' behavior (so maps are the same). Fixes: ac01c8c ("perf hist: Update hist symbol when updating maps") Signed-off-by: Namhyung Kim <namhyung@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Matt Fleming <matt@readmodwrite.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Link: https://lore.kernel.org/r/20240826221045.1202305-2-namhyung@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

commit 823430c ("memory tier: consolidate the initialization of memory tiers") introduces a locking change that use guard(mutex) to instead of mutex_lock/unlock() for memory_tier_lock. It unexpectedly expanded the locked region to include the hotplug_memory_notifier(), as a result, it triggers an locking dependency detected of ABBA deadlock. Exclude hotplug_memory_notifier() from the locked region to fixing it. The deadlock scenario is that when a memory online event occurs, the execution of memory notifier will access the read lock of the memory_chain.rwsem, then the reigistration of the memory notifier in memory_tier_init() acquires the write lock of the memory_chain.rwsem while holding memory_tier_lock. Then the memory online event continues to invoke the memory hotplug callback registered by memory_tier_init(). Since this callback tries to acquire the memory_tier_lock, a deadlock occurs. In fact, this deadlock can't happen because memory_tier_init() always executes before memory online events happen due to the subsys_initcall() has an higher priority than module_init(). [ 133.491106] WARNING: possible circular locking dependency detected [ 133.493656] 6.11.0-rc2+ openbmc#146 Tainted: G O N [ 133.504290] ------------------------------------------------------ [ 133.515194] (udev-worker)/1133 is trying to acquire lock: [ 133.525715] ffffffff87044e28 (memory_tier_lock){+.+.}-{3:3}, at: memtier_hotplug_callback+0x383/0x4b0 [ 133.536449] [ 133.536449] but task is already holding lock: [ 133.549847] ffffffff875d3310 ((memory_chain).rwsem){++++}-{3:3}, at: blocking_notifier_call_chain+0x60/0xb0 [ 133.556781] [ 133.556781] which lock already depends on the new lock. [ 133.556781] [ 133.569957] [ 133.569957] the existing dependency chain (in reverse order) is: [ 133.577618] [ 133.577618] -> openbmc#1 ((memory_chain).rwsem){++++}-{3:3}: [ 133.584997] down_write+0x97/0x210 [ 133.588647] blocking_notifier_chain_register+0x71/0xd0 [ 133.592537] register_memory_notifier+0x26/0x30 [ 133.596314] memory_tier_init+0x187/0x300 [ 133.599864] do_one_initcall+0x117/0x5d0 [ 133.603399] kernel_init_freeable+0xab0/0xeb0 [ 133.606986] kernel_init+0x28/0x2f0 [ 133.610312] ret_from_fork+0x59/0x90 [ 133.613652] ret_from_fork_asm+0x1a/0x30 [ 133.617012] [ 133.617012] -> #0 (memory_tier_lock){+.+.}-{3:3}: [ 133.623390] __lock_acquire+0x2efd/0x5c60 [ 133.626730] lock_acquire+0x1ce/0x580 [ 133.629757] __mutex_lock+0x15c/0x1490 [ 133.632731] mutex_lock_nested+0x1f/0x30 [ 133.635717] memtier_hotplug_callback+0x383/0x4b0 [ 133.638748] notifier_call_chain+0xbf/0x370 [ 133.641647] blocking_notifier_call_chain+0x76/0xb0 [ 133.644636] memory_notify+0x2e/0x40 [ 133.647427] online_pages+0x597/0x720 [ 133.650246] memory_subsys_online+0x4f6/0x7f0 [ 133.653107] device_online+0x141/0x1d0 [ 133.655831] online_memory_block+0x4d/0x60 [ 133.658616] walk_memory_blocks+0xc0/0x120 [ 133.661419] add_memory_resource+0x51d/0x6c0 [ 133.664202] add_memory_driver_managed+0xf5/0x180 [ 133.667060] dev_dax_kmem_probe+0x7f7/0xb40 [kmem] [ 133.669949] dax_bus_probe+0x147/0x230 [ 133.672687] really_probe+0x27f/0xac0 [ 133.675463] __driver_probe_device+0x1f3/0x460 [ 133.678493] driver_probe_device+0x56/0x1b0 [ 133.681366] __driver_attach+0x277/0x570 [ 133.684149] bus_for_each_dev+0x145/0x1e0 [ 133.686937] driver_attach+0x49/0x60 [ 133.689673] bus_add_driver+0x2f3/0x6b0 [ 133.692421] driver_register+0x170/0x4b0 [ 133.695118] __dax_driver_register+0x141/0x1b0 [ 133.697910] dax_kmem_init+0x54/0xff0 [kmem] [ 133.700794] do_one_initcall+0x117/0x5d0 [ 133.703455] do_init_module+0x277/0x750 [ 133.706054] load_module+0x5d1d/0x74f0 [ 133.708602] init_module_from_file+0x12c/0x1a0 [ 133.711234] idempotent_init_module+0x3f1/0x690 [ 133.713937] __x64_sys_finit_module+0x10e/0x1a0 [ 133.716492] x64_sys_call+0x184d/0x20d0 [ 133.719053] do_syscall_64+0x6d/0x140 [ 133.721537] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ 133.724239] [ 133.724239] other info that might help us debug this: [ 133.724239] [ 133.730832] Possible unsafe locking scenario: [ 133.730832] [ 133.735298] CPU0 CPU1 [ 133.737759] ---- ---- [ 133.740165] rlock((memory_chain).rwsem); [ 133.742623] lock(memory_tier_lock); [ 133.745357] lock((memory_chain).rwsem); [ 133.748141] lock(memory_tier_lock); [ 133.750489] [ 133.750489] *** DEADLOCK *** [ 133.750489] [ 133.756742] 6 locks held by (udev-worker)/1133: [ 133.759179] #0: ffff888207be6158 (&dev->mutex){....}-{3:3}, at: __driver_attach+0x26c/0x570 [ 133.762299] openbmc#1: ffffffff875b5868 (device_hotplug_lock){+.+.}-{3:3}, at: lock_device_hotplug+0x20/0x30 [ 133.765565] openbmc#2: ffff88820cf6a108 (&dev->mutex){....}-{3:3}, at: device_online+0x2f/0x1d0 [ 133.768978] openbmc#3: ffffffff86d08ff0 (cpu_hotplug_lock){++++}-{0:0}, at: mem_hotplug_begin+0x17/0x30 [ 133.772312] openbmc#4: ffffffff8702dfb0 (mem_hotplug_lock){++++}-{0:0}, at: mem_hotplug_begin+0x23/0x30 [ 133.775544] openbmc#5: ffffffff875d3310 ((memory_chain).rwsem){++++}-{3:3}, at: blocking_notifier_call_chain+0x60/0xb0 [ 133.779113] [ 133.779113] stack backtrace: [ 133.783728] CPU: 5 UID: 0 PID: 1133 Comm: (udev-worker) Tainted: G O N 6.11.0-rc2+ openbmc#146 [ 133.787220] Tainted: [O]=OOT_MODULE, [N]=TEST [ 133.789948] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015 [ 133.793291] Call Trace: [ 133.795826] <TASK> [ 133.798284] dump_stack_lvl+0xea/0x150 [ 133.801025] dump_stack+0x19/0x20 [ 133.803609] print_circular_bug+0x477/0x740 [ 133.806341] check_noncircular+0x2f4/0x3e0 [ 133.809056] ? __pfx_check_noncircular+0x10/0x10 [ 133.811866] ? __pfx_lockdep_lock+0x10/0x10 [ 133.814670] ? __sanitizer_cov_trace_const_cmp8+0x1c/0x30 [ 133.817610] __lock_acquire+0x2efd/0x5c60 [ 133.820339] ? __pfx___lock_acquire+0x10/0x10 [ 133.823128] ? __dax_driver_register+0x141/0x1b0 [ 133.825926] ? do_one_initcall+0x117/0x5d0 [ 133.828648] lock_acquire+0x1ce/0x580 [ 133.831349] ? memtier_hotplug_callback+0x383/0x4b0 [ 133.834293] ? __pfx_lock_acquire+0x10/0x10 [ 133.837134] __mutex_lock+0x15c/0x1490 [ 133.839829] ? memtier_hotplug_callback+0x383/0x4b0 [ 133.842753] ? memtier_hotplug_callback+0x383/0x4b0 [ 133.845602] ? __this_cpu_preempt_check+0x21/0x30 [ 133.848438] ? __pfx___mutex_lock+0x10/0x10 [ 133.851200] ? __pfx_lock_acquire+0x10/0x10 [ 133.853935] ? global_dirty_limits+0xc0/0x160 [ 133.856699] ? __sanitizer_cov_trace_switch+0x58/0xa0 [ 133.859564] mutex_lock_nested+0x1f/0x30 [ 133.862251] ? mutex_lock_nested+0x1f/0x30 [ 133.864964] memtier_hotplug_callback+0x383/0x4b0 [ 133.867752] notifier_call_chain+0xbf/0x370 [ 133.870550] ? writeback_set_ratelimit+0xe8/0x160 [ 133.873372] blocking_notifier_call_chain+0x76/0xb0 [ 133.876311] memory_notify+0x2e/0x40 [ 133.879013] online_pages+0x597/0x720 [ 133.881686] ? irqentry_exit+0x3e/0xa0 [ 133.884397] ? __pfx_online_pages+0x10/0x10 [ 133.887244] ? __sanitizer_cov_trace_const_cmp8+0x1c/0x30 [ 133.890299] ? mhp_init_memmap_on_memory+0x7a/0x1c0 [ 133.893203] memory_subsys_online+0x4f6/0x7f0 [ 133.896099] ? __pfx_memory_subsys_online+0x10/0x10 [ 133.899039] ? xa_load+0x16d/0x2e0 [ 133.901667] ? __pfx_xa_load+0x10/0x10 [ 133.904366] ? __pfx_memory_subsys_online+0x10/0x10 [ 133.907218] device_online+0x141/0x1d0 [ 133.909845] online_memory_block+0x4d/0x60 [ 133.912494] walk_memory_blocks+0xc0/0x120 [ 133.915104] ? __pfx_online_memory_block+0x10/0x10 [ 133.917776] add_memory_resource+0x51d/0x6c0 [ 133.920404] ? __pfx_add_memory_resource+0x10/0x10 [ 133.923104] ? _raw_write_unlock+0x31/0x60 [ 133.925781] ? register_memory_resource+0x119/0x180 [ 133.928450] add_memory_driver_managed+0xf5/0x180 [ 133.931036] dev_dax_kmem_probe+0x7f7/0xb40 [kmem] [ 133.933665] ? __pfx_dev_dax_kmem_probe+0x10/0x10 [kmem] [ 133.936332] ? __pfx___up_read+0x10/0x10 [ 133.938878] dax_bus_probe+0x147/0x230 [ 133.941332] ? __pfx_dax_bus_probe+0x10/0x10 [ 133.943954] really_probe+0x27f/0xac0 [ 133.946387] ? __sanitizer_cov_trace_const_cmp1+0x1e/0x30 [ 133.949106] __driver_probe_device+0x1f3/0x460 [ 133.951704] ? parse_option_str+0x149/0x190 [ 133.954241] driver_probe_device+0x56/0x1b0 [ 133.956749] __driver_attach+0x277/0x570 [ 133.959228] ? __pfx___driver_attach+0x10/0x10 [ 133.961776] bus_for_each_dev+0x145/0x1e0 [ 133.964367] ? __pfx_bus_for_each_dev+0x10/0x10 [ 133.967019] ? __kasan_check_read+0x15/0x20 [ 133.969543] ? _raw_spin_unlock+0x31/0x60 [ 133.972132] driver_attach+0x49/0x60 [ 133.974536] bus_add_driver+0x2f3/0x6b0 [ 133.977044] driver_register+0x170/0x4b0 [ 133.979480] __dax_driver_register+0x141/0x1b0 [ 133.982126] ? __pfx_dax_kmem_init+0x10/0x10 [kmem] [ 133.984724] dax_kmem_init+0x54/0xff0 [kmem] [ 133.987284] ? __pfx_dax_kmem_init+0x10/0x10 [kmem] [ 133.989965] do_one_initcall+0x117/0x5d0 [ 133.992506] ? __pfx_do_one_initcall+0x10/0x10 [ 133.995185] ? __kasan_kmalloc+0x88/0xa0 [ 133.997748] ? kasan_poison+0x3e/0x60 [ 134.000288] ? kasan_unpoison+0x2c/0x60 [ 134.002762] ? kasan_poison+0x3e/0x60 [ 134.005202] ? __asan_register_globals+0x62/0x80 [ 134.007753] ? __pfx_dax_kmem_init+0x10/0x10 [kmem] [ 134.010439] do_init_module+0x277/0x750 [ 134.012953] load_module+0x5d1d/0x74f0 [ 134.015406] ? __pfx_load_module+0x10/0x10 [ 134.017887] ? __pfx_ima_post_read_file+0x10/0x10 [ 134.020470] ? __sanitizer_cov_trace_const_cmp8+0x1c/0x30 [ 134.023127] ? __sanitizer_cov_trace_const_cmp4+0x1a/0x20 [ 134.025767] ? security_kernel_post_read_file+0xa2/0xd0 [ 134.028429] ? __sanitizer_cov_trace_const_cmp4+0x1a/0x20 [ 134.031162] ? kernel_read_file+0x503/0x820 [ 134.033645] ? __pfx_kernel_read_file+0x10/0x10 [ 134.036232] ? __pfx___lock_acquire+0x10/0x10 [ 134.038766] init_module_from_file+0x12c/0x1a0 [ 134.041291] ? init_module_from_file+0x12c/0x1a0 [ 134.043936] ? __pfx_init_module_from_file+0x10/0x10 [ 134.046516] ? __this_cpu_preempt_check+0x21/0x30 [ 134.049091] ? __kasan_check_read+0x15/0x20 [ 134.051551] ? do_raw_spin_unlock+0x60/0x210 [ 134.054077] idempotent_init_module+0x3f1/0x690 [ 134.056643] ? __pfx_idempotent_init_module+0x10/0x10 [ 134.059318] ? __sanitizer_cov_trace_const_cmp4+0x1a/0x20 [ 134.061995] ? __fget_light+0x17d/0x210 [ 134.064428] __x64_sys_finit_module+0x10e/0x1a0 [ 134.066976] x64_sys_call+0x184d/0x20d0 [ 134.069405] do_syscall_64+0x6d/0x140 [ 134.071926] entry_SYSCALL_64_after_hwframe+0x76/0x7e [yanfei.xu@intel.com: add mutex_lock/unlock() pair back] Link: https://lkml.kernel.org/r/20240830102447.1445296-1-yanfei.xu@intel.com Link: https://lkml.kernel.org/r/20240827113614.1343049-1-yanfei.xu@intel.com Fixes: 823430c ("memory tier: consolidate the initialization of memory tiers") Signed-off-by: Yanfei Xu <yanfei.xu@intel.com> Reviewed-by: "Huang, Ying" <ying.huang@intel.com> Cc: Ho-Ren (Jack) Chuang <horen.chuang@linux.dev> Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

commit ac01c8c upstream. AddressSanitizer found a use-after-free bug in the symbol code which manifested as 'perf top' segfaulting. ==1238389==ERROR: AddressSanitizer: heap-use-after-free on address 0x60b00c48844b at pc 0x5650d8035961 bp 0x7f751aaecc90 sp 0x7f751aaecc80 READ of size 1 at 0x60b00c48844b thread T193 #0 0x5650d8035960 in _sort__sym_cmp util/sort.c:310 #1 0x5650d8043744 in hist_entry__cmp util/hist.c:1286 #2 0x5650d8043951 in hists__findnew_entry util/hist.c:614 #3 0x5650d804568f in __hists__add_entry util/hist.c:754 #4 0x5650d8045bf9 in hists__add_entry util/hist.c:772 #5 0x5650d8045df1 in iter_add_single_normal_entry util/hist.c:997 #6 0x5650d8043326 in hist_entry_iter__add util/hist.c:1242 #7 0x5650d7ceeefe in perf_event__process_sample /home/matt/src/linux/tools/perf/builtin-top.c:845 #8 0x5650d7ceeefe in deliver_event /home/matt/src/linux/tools/perf/builtin-top.c:1208 #9 0x5650d7fdb51b in do_flush util/ordered-events.c:245 #10 0x5650d7fdb51b in __ordered_events__flush util/ordered-events.c:324 #11 0x5650d7ced743 in process_thread /home/matt/src/linux/tools/perf/builtin-top.c:1120 #12 0x7f757ef1f133 in start_thread nptl/pthread_create.c:442 #13 0x7f757ef9f7db in clone3 ../sysdeps/unix/sysv/linux/x86_64/clone3.S:81 When updating hist maps it's also necessary to update the hist symbol reference because the old one gets freed in map__put(). While this bug was probably introduced with 5c24b67 ("perf tools: Replace map->referenced & maps->removed_maps with map->refcnt"), the symbol objects were leaked until c087e94 ("perf machine: Fix refcount usage when processing PERF_RECORD_KSYMBOL") was merged so the bug was masked. Fixes: c087e94 ("perf machine: Fix refcount usage when processing PERF_RECORD_KSYMBOL") Reported-by: Yunzhao Li <yunzhao@cloudflare.com> Signed-off-by: Matt Fleming (Cloudflare) <matt@readmodwrite.com> Cc: Ian Rogers <irogers@google.com> Cc: kernel-team@cloudflare.com Cc: Namhyung Kim <namhyung@kernel.org> Cc: Riccardo Mancini <rickyman7@gmail.com> Cc: stable@vger.kernel.org # v5.13+ Link: https://lore.kernel.org/r/20240815142212.3834625-1-matt@readmodwrite.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 9af2efe upstream. The fields in the hist_entry are filled on-demand which means they only have meaningful values when relevant sort keys are used. So if neither of 'dso' nor 'sym' sort keys are used, the map/symbols in the hist entry can be garbage. So it shouldn't access it unconditionally. I got a segfault, when I wanted to see cgroup profiles. $ sudo perf record -a --all-cgroups --synth=cgroup true $ sudo perf report -s cgroup Program received signal SIGSEGV, Segmentation fault. 0x00005555557a8d90 in map__dso (map=0x0) at util/map.h:48 48 return RC_CHK_ACCESS(map)->dso; (gdb) bt #0 0x00005555557a8d90 in map__dso (map=0x0) at util/map.h:48 #1 0x00005555557aa39b in map__load (map=0x0) at util/map.c:344 #2 0x00005555557aa592 in map__find_symbol (map=0x0, addr=140736115941088) at util/map.c:385 #3 0x00005555557ef000 in hists__findnew_entry (hists=0x555556039d60, entry=0x7fffffffa4c0, al=0x7fffffffa8c0, sample_self=true) at util/hist.c:644 #4 0x00005555557ef61c in __hists__add_entry (hists=0x555556039d60, al=0x7fffffffa8c0, sym_parent=0x0, bi=0x0, mi=0x0, ki=0x0, block_info=0x0, sample=0x7fffffffaa90, sample_self=true, ops=0x0) at util/hist.c:761 #5 0x00005555557ef71f in hists__add_entry (hists=0x555556039d60, al=0x7fffffffa8c0, sym_parent=0x0, bi=0x0, mi=0x0, ki=0x0, sample=0x7fffffffaa90, sample_self=true) at util/hist.c:779 #6 0x00005555557f00fb in iter_add_single_normal_entry (iter=0x7fffffffa900, al=0x7fffffffa8c0) at util/hist.c:1015 #7 0x00005555557f09a7 in hist_entry_iter__add (iter=0x7fffffffa900, al=0x7fffffffa8c0, max_stack_depth=127, arg=0x7fffffffbce0) at util/hist.c:1260 #8 0x00005555555ba7ce in process_sample_event (tool=0x7fffffffbce0, event=0x7ffff7c14128, sample=0x7fffffffaa90, evsel=0x555556039ad0, machine=0x5555560388e8) at builtin-report.c:334 #9 0x00005555557b30c8 in evlist__deliver_sample (evlist=0x555556039010, tool=0x7fffffffbce0, event=0x7ffff7c14128, sample=0x7fffffffaa90, evsel=0x555556039ad0, machine=0x5555560388e8) at util/session.c:1232 #10 0x00005555557b32bc in machines__deliver_event (machines=0x5555560388e8, evlist=0x555556039010, event=0x7ffff7c14128, sample=0x7fffffffaa90, tool=0x7fffffffbce0, file_offset=110888, file_path=0x555556038ff0 "perf.data") at util/session.c:1271 #11 0x00005555557b3848 in perf_session__deliver_event (session=0x5555560386d0, event=0x7ffff7c14128, tool=0x7fffffffbce0, file_offset=110888, file_path=0x555556038ff0 "perf.data") at util/session.c:1354 #12 0x00005555557affaf in ordered_events__deliver_event (oe=0x555556038e60, event=0x555556135aa0) at util/session.c:132 #13 0x00005555557bb605 in do_flush (oe=0x555556038e60, show_progress=false) at util/ordered-events.c:245 #14 0x00005555557bb95c in __ordered_events__flush (oe=0x555556038e60, how=OE_FLUSH__ROUND, timestamp=0) at util/ordered-events.c:324 #15 0x00005555557bba46 in ordered_events__flush (oe=0x555556038e60, how=OE_FLUSH__ROUND) at util/ordered-events.c:342 #16 0x00005555557b1b3b in perf_event__process_finished_round (tool=0x7fffffffbce0, event=0x7ffff7c15bb8, oe=0x555556038e60) at util/session.c:780 #17 0x00005555557b3b27 in perf_session__process_user_event (session=0x5555560386d0, event=0x7ffff7c15bb8, file_offset=117688, file_path=0x555556038ff0 "perf.data") at util/session.c:1406 As you can see the entry->ms.map was NULL even if he->ms.map has a value. This is because 'sym' sort key is not given, so it cannot assume whether he->ms.sym and entry->ms.sym is the same. I only checked the 'sym' sort key here as it implies 'dso' behavior (so maps are the same). Fixes: ac01c8c ("perf hist: Update hist symbol when updating maps") Signed-off-by: Namhyung Kim <namhyung@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Matt Fleming <matt@readmodwrite.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Link: https://lore.kernel.org/r/20240826221045.1202305-2-namhyung@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

…tion to perf_sched__replay() [ Upstream commit c690786 ] The start_work_mutex and work_done_wait_mutex are used only for the 'perf sched replay'. Put their initialization in perf_sched__replay () to reduce unnecessary actions in other commands. Simple functional testing: # perf sched record perf bench sched messaging # Running 'sched/messaging' benchmark: # 20 sender and receiver processes per group # 10 groups == 400 processes run Total time: 0.197 [sec] [ perf record: Woken up 1 times to write data ] [ perf record: Captured and wrote 14.952 MB perf.data (134165 samples) ] # perf sched replay run measurement overhead: 108 nsecs sleep measurement overhead: 65658 nsecs the run test took 999991 nsecs the sleep test took 1079324 nsecs nr_run_events: 42378 nr_sleep_events: 43102 nr_wakeup_events: 31852 target-less wakeups: 17 multi-target wakeups: 712 task 0 ( swapper: 0), nr_events: 10451 task 1 ( swapper: 1), nr_events: 3 task 2 ( swapper: 2), nr_events: 1 <SNIP> task 717 ( sched-messaging: 74483), nr_events: 152 task 718 ( sched-messaging: 74484), nr_events: 1944 task 719 ( sched-messaging: 74485), nr_events: 73 task 720 ( sched-messaging: 74486), nr_events: 163 task 721 ( sched-messaging: 74487), nr_events: 942 task 722 ( sched-messaging: 74488), nr_events: 78 task 723 ( sched-messaging: 74489), nr_events: 1090 ------------------------------------------------------------ #1 : 1366.507, ravg: 1366.51, cpu: 7682.70 / 7682.70 #2 : 1410.072, ravg: 1370.86, cpu: 7723.88 / 7686.82 #3 : 1396.296, ravg: 1373.41, cpu: 7568.20 / 7674.96 #4 : 1381.019, ravg: 1374.17, cpu: 7531.81 / 7660.64 #5 : 1393.826, ravg: 1376.13, cpu: 7725.25 / 7667.11 #6 : 1401.581, ravg: 1378.68, cpu: 7594.82 / 7659.88 #7 : 1381.337, ravg: 1378.94, cpu: 7371.22 / 7631.01 #8 : 1373.842, ravg: 1378.43, cpu: 7894.92 / 7657.40 #9 : 1364.697, ravg: 1377.06, cpu: 7324.91 / 7624.15 #10 : 1363.613, ravg: 1375.72, cpu: 7209.55 / 7582.69 # echo $? 0 Signed-off-by: Yang Jihong <yangjihong1@huawei.com> Signed-off-by: Namhyung Kim <namhyung@kernel.org> Link: https://lore.kernel.org/r/20240206083228.172607-2-yangjihong1@huawei.com Stable-dep-of: 1a5efc9 ("libsubcmd: Don't free the usage string") Signed-off-by: Sasha Levin <sashal@kernel.org>

…f_sched__{lat|map|replay}() [ Upstream commit bd2cdf2 ] The curr_pid and cpu_last_switched are used only for the 'perf sched replay/latency/map'. Put their initialization in perf_sched__{lat|map|replay () to reduce unnecessary actions in other commands. Simple functional testing: # perf sched record perf bench sched messaging # Running 'sched/messaging' benchmark: # 20 sender and receiver processes per group # 10 groups == 400 processes run Total time: 0.209 [sec] [ perf record: Woken up 1 times to write data ] [ perf record: Captured and wrote 16.456 MB perf.data (147907 samples) ] # perf sched lat ------------------------------------------------------------------------------------------------------------------------------------------- Task | Runtime ms | Switches | Avg delay ms | Max delay ms | Max delay start | Max delay end | ------------------------------------------------------------------------------------------------------------------------------------------- sched-messaging:(401) | 2990.699 ms | 38705 | avg: 0.661 ms | max: 67.046 ms | max start: 456532.624830 s | max end: 456532.691876 s qemu-system-x86:(7) | 179.764 ms | 2191 | avg: 0.152 ms | max: 21.857 ms | max start: 456532.576434 s | max end: 456532.598291 s sshd:48125 | 0.522 ms | 2 | avg: 0.037 ms | max: 0.046 ms | max start: 456532.514610 s | max end: 456532.514656 s <SNIP> ksoftirqd/11:82 | 0.063 ms | 1 | avg: 0.005 ms | max: 0.005 ms | max start: 456532.769366 s | max end: 456532.769371 s kworker/9:0-mm_:34624 | 0.233 ms | 20 | avg: 0.004 ms | max: 0.007 ms | max start: 456532.690804 s | max end: 456532.690812 s migration/13:93 | 0.000 ms | 1 | avg: 0.004 ms | max: 0.004 ms | max start: 456532.512669 s | max end: 456532.512674 s ----------------------------------------------------------------------------------------------------------------- TOTAL: | 3180.750 ms | 41368 | --------------------------------------------------- # echo $? 0 # perf sched map *A0 456532.510141 secs A0 => migration/0:15 *. 456532.510171 secs . => swapper:0 . *B0 456532.510261 secs B0 => migration/1:21 . *. 456532.510279 secs <SNIP> L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 *L7 . . . . 456532.785979 secs L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 *L7 . . . 456532.786054 secs L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 *L7 . . 456532.786127 secs L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 *L7 . 456532.786197 secs L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 *L7 456532.786270 secs # echo $? 0 # perf sched replay run measurement overhead: 108 nsecs sleep measurement overhead: 66473 nsecs the run test took 1000002 nsecs the sleep test took 1082686 nsecs nr_run_events: 49334 nr_sleep_events: 50054 nr_wakeup_events: 34701 target-less wakeups: 165 multi-target wakeups: 766 task 0 ( swapper: 0), nr_events: 15419 task 1 ( swapper: 1), nr_events: 1 task 2 ( swapper: 2), nr_events: 1 <SNIP> task 715 ( sched-messaging: 110248), nr_events: 1438 task 716 ( sched-messaging: 110249), nr_events: 512 task 717 ( sched-messaging: 110250), nr_events: 500 task 718 ( sched-messaging: 110251), nr_events: 537 task 719 ( sched-messaging: 110252), nr_events: 823 ------------------------------------------------------------ #1 : 1325.288, ravg: 1325.29, cpu: 7823.35 / 7823.35 #2 : 1363.606, ravg: 1329.12, cpu: 7655.53 / 7806.56 #3 : 1349.494, ravg: 1331.16, cpu: 7544.80 / 7780.39 #4 : 1311.488, ravg: 1329.19, cpu: 7495.13 / 7751.86 #5 : 1309.902, ravg: 1327.26, cpu: 7266.65 / 7703.34 #6 : 1309.535, ravg: 1325.49, cpu: 7843.86 / 7717.39 #7 : 1316.482, ravg: 1324.59, cpu: 7854.41 / 7731.09 #8 : 1366.604, ravg: 1328.79, cpu: 7955.81 / 7753.57 #9 : 1326.286, ravg: 1328.54, cpu: 7466.86 / 7724.90 #10 : 1356.653, ravg: 1331.35, cpu: 7566.60 / 7709.07 # echo $? 0 Signed-off-by: Yang Jihong <yangjihong1@huawei.com> Signed-off-by: Namhyung Kim <namhyung@kernel.org> Link: https://lore.kernel.org/r/20240206083228.172607-5-yangjihong1@huawei.com Stable-dep-of: 1a5efc9 ("libsubcmd: Don't free the usage string") Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a848c29 ] On the node of an NFS client, some files saved in the mountpoint of the NFS server were copied to another location of the same NFS server. Accidentally, the nfs42_complete_copies() got a NULL-pointer dereference crash with the following syslog: [232064.838881] NFSv4: state recovery failed for open file nfs/pvc-12b5200d-cd0f-46a3-b9f0-af8f4fe0ef64.qcow2, error = -116 [232064.839360] NFSv4: state recovery failed for open file nfs/pvc-12b5200d-cd0f-46a3-b9f0-af8f4fe0ef64.qcow2, error = -116 [232066.588183] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000058 [232066.588586] Mem abort info: [232066.588701] ESR = 0x0000000096000007 [232066.588862] EC = 0x25: DABT (current EL), IL = 32 bits [232066.589084] SET = 0, FnV = 0 [232066.589216] EA = 0, S1PTW = 0 [232066.589340] FSC = 0x07: level 3 translation fault [232066.589559] Data abort info: [232066.589683] ISV = 0, ISS = 0x00000007 [232066.589842] CM = 0, WnR = 0 [232066.589967] user pgtable: 64k pages, 48-bit VAs, pgdp=00002000956ff400 [232066.590231] [0000000000000058] pgd=08001100ae100003, p4d=08001100ae100003, pud=08001100ae100003, pmd=08001100b3c00003, pte=0000000000000000 [232066.590757] Internal error: Oops: 96000007 [#1] SMP [232066.590958] Modules linked in: rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver nfs lockd grace fscache netfs ocfs2_dlmfs ocfs2_stack_o2cb ocfs2_dlm vhost_net vhost vhost_iotlb tap tun ipt_rpfilter xt_multiport ip_set_hash_ip ip_set_hash_net xfrm_interface xfrm6_tunnel tunnel4 tunnel6 esp4 ah4 wireguard libcurve25519_generic veth xt_addrtype xt_set nf_conntrack_netlink ip_set_hash_ipportnet ip_set_hash_ipportip ip_set_bitmap_port ip_set_hash_ipport dummy ip_set ip_vs_sh ip_vs_wrr ip_vs_rr ip_vs iptable_filter sch_ingress nfnetlink_cttimeout vport_gre ip_gre ip_tunnel gre vport_geneve geneve vport_vxlan vxlan ip6_udp_tunnel udp_tunnel openvswitch nf_conncount dm_round_robin dm_service_time dm_multipath xt_nat xt_MASQUERADE nft_chain_nat nf_nat xt_mark xt_conntrack xt_comment nft_compat nft_counter nf_tables nfnetlink ocfs2 ocfs2_nodemanager ocfs2_stackglue iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi ipmi_ssif nbd overlay 8021q garp mrp bonding tls rfkill sunrpc ext4 mbcache jbd2 [232066.591052] vfat fat cas_cache cas_disk ses enclosure scsi_transport_sas sg acpi_ipmi ipmi_si ipmi_devintf ipmi_msghandler ip_tables vfio_pci vfio_pci_core vfio_virqfd vfio_iommu_type1 vfio dm_mirror dm_region_hash dm_log dm_mod nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 br_netfilter bridge stp llc fuse xfs libcrc32c ast drm_vram_helper qla2xxx drm_kms_helper syscopyarea crct10dif_ce sysfillrect ghash_ce sysimgblt sha2_ce fb_sys_fops cec sha256_arm64 sha1_ce drm_ttm_helper ttm nvme_fc igb sbsa_gwdt nvme_fabrics drm nvme_core i2c_algo_bit i40e scsi_transport_fc megaraid_sas aes_neon_bs [232066.596953] CPU: 6 PID: 4124696 Comm: 10.253.166.125- Kdump: loaded Not tainted 5.15.131-9.cl9_ocfs2.aarch64 #1 [232066.597356] Hardware name: Great Wall .\x93\x8e...RF6260 V5/GWMSSE2GL1T, BIOS T656FBE_V3.0.18 2024-01-06 [232066.597721] pstate: 20400009 (nzCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [232066.598034] pc : nfs4_reclaim_open_state+0x220/0x800 [nfsv4] [232066.598327] lr : nfs4_reclaim_open_state+0x12c/0x800 [nfsv4] [232066.598595] sp : ffff8000f568fc70 [232066.598731] x29: ffff8000f568fc70 x28: 0000000000001000 x27: ffff21003db33000 [232066.599030] x26: ffff800005521ae0 x25: ffff0100f98fa3f0 x24: 0000000000000001 [232066.599319] x23: ffff800009920008 x22: ffff21003db33040 x21: ffff21003db33050 [232066.599628] x20: ffff410172fe9e40 x19: ffff410172fe9e00 x18: 0000000000000000 [232066.599914] x17: 0000000000000000 x16: 0000000000000004 x15: 0000000000000000 [232066.600195] x14: 0000000000000000 x13: ffff800008e685a8 x12: 00000000eac0c6e6 [232066.600498] x11: 0000000000000000 x10: 0000000000000008 x9 : ffff8000054e5828 [232066.600784] x8 : 00000000ffffffbf x7 : 0000000000000001 x6 : 000000000a9eb14a [232066.601062] x5 : 0000000000000000 x4 : ffff70ff8a14a800 x3 : 0000000000000058 [232066.601348] x2 : 0000000000000001 x1 : 54dce46366daa6c6 x0 : 0000000000000000 [232066.601636] Call trace: [232066.601749] nfs4_reclaim_open_state+0x220/0x800 [nfsv4] [232066.601998] nfs4_do_reclaim+0x1b8/0x28c [nfsv4] [232066.602218] nfs4_state_manager+0x928/0x10f0 [nfsv4] [232066.602455] nfs4_run_state_manager+0x78/0x1b0 [nfsv4] [232066.602690] kthread+0x110/0x114 [232066.602830] ret_from_fork+0x10/0x20 [232066.602985] Code: 1400000d f9403f20 f9402e61 91016003 (f9402c00) [232066.603284] SMP: stopping secondary CPUs [232066.606936] Starting crashdump kernel... [232066.607146] Bye! Analysing the vmcore, we know that nfs4_copy_state listed by destination nfs_server->ss_copies was added by the field copies in handle_async_copy(), and we found a waiting copy process with the stack as: PID: 3511963 TASK: ffff710028b47e00 CPU: 0 COMMAND: "cp" #0 [ffff8001116ef740] __switch_to at ffff8000081b92f4 #1 [ffff8001116ef760] __schedule at ffff800008dd0650 #2 [ffff8001116ef7c0] schedule at ffff800008dd0a00 #3 [ffff8001116ef7e0] schedule_timeout at ffff800008dd6aa0 #4 [ffff8001116ef860] __wait_for_common at ffff800008dd166c #5 [ffff8001116ef8e0] wait_for_completion_interruptible at ffff800008dd1898 #6 [ffff8001116ef8f0] handle_async_copy at ffff8000055142f4 [nfsv4] #7 [ffff8001116ef970] _nfs42_proc_copy at ffff8000055147c8 [nfsv4] #8 [ffff8001116efa80] nfs42_proc_copy at ffff800005514cf0 [nfsv4] #9 [ffff8001116efc50] __nfs4_copy_file_range.constprop.0 at ffff8000054ed694 [nfsv4] The NULL-pointer dereference was due to nfs42_complete_copies() listed the nfs_server->ss_copies by the field ss_copies of nfs4_copy_state. So the nfs4_copy_state address ffff0100f98fa3f0 was offset by 0x10 and the data accessed through this pointer was also incorrect. Generally, the ordered list nfs4_state_owner->so_states indicate open(O_RDWR) or open(O_WRITE) states are reclaimed firstly by nfs4_reclaim_open_state(). When destination state reclaim is failed with NFS_STATE_RECOVERY_FAILED and copies are not deleted in nfs_server->ss_copies, the source state may be passed to the nfs42_complete_copies() process earlier, resulting in this crash scene finally. To solve this issue, we add a list_head nfs_server->ss_src_copies for a server-to-server copy specially. Fixes: 0e65a32 ("NFS: handle source server reboot") Signed-off-by: Yanjun Zhang <zhangyanjun@cestc.cn> Reviewed-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

…ation commit c728a95 upstream. When testing the XDP_REDIRECT function on the LS1028A platform, we found a very reproducible issue that the Tx frames can no longer be sent out even if XDP_REDIRECT is turned off. Specifically, if there is a lot of traffic on Rx direction, when XDP_REDIRECT is turned on, the console may display some warnings like "timeout for tx ring #6 clear", and all redirected frames will be dropped, the detailed log is as follows. root@ls1028ardb:~# ./xdp-bench redirect eno0 eno2 Redirecting from eno0 (ifindex 3; driver fsl_enetc) to eno2 (ifindex 4; driver fsl_enetc) [203.849809] fsl_enetc 0000:00:00.2 eno2: timeout for tx ring #5 clear [204.006051] fsl_enetc 0000:00:00.2 eno2: timeout for tx ring #6 clear [204.161944] fsl_enetc 0000:00:00.2 eno2: timeout for tx ring #7 clear eno0->eno2 1420505 rx/s 1420590 err,drop/s 0 xmit/s xmit eno0->eno2 0 xmit/s 1420590 drop/s 0 drv_err/s 15.71 bulk-avg eno0->eno2 1420484 rx/s 1420485 err,drop/s 0 xmit/s xmit eno0->eno2 0 xmit/s 1420485 drop/s 0 drv_err/s 15.71 bulk-avg By analyzing the XDP_REDIRECT implementation of enetc driver, the driver will reconfigure Tx and Rx BD rings when a bpf program is installed or uninstalled, but there is no mechanisms to block the redirected frames when enetc driver reconfigures rings. Similarly, XDP_TX verdicts on received frames can also lead to frames being enqueued in the Tx rings. Because XDP ignores the state set by the netif_tx_wake_queue() API, so introduce the ENETC_TX_DOWN flag to suppress transmission of XDP frames. Fixes: c33bfaf ("net: enetc: set up XDP program under enetc_reconfigure()") Cc: stable@vger.kernel.org Signed-off-by: Wei Fang <wei.fang@nxp.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://patch.msgid.link/20241010092056.298128-3-wei.fang@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 348a198 upstream. Luis has been reporting an assert failure when freeing an inode cluster during inode inactivation for a while. The assert looks like: XFS: Assertion failed: bp->b_flags & XBF_DONE, file: fs/xfs/xfs_trans_buf.c, line: 241 ------------[ cut here ]------------ kernel BUG at fs/xfs/xfs_message.c:102! Oops: invalid opcode: 0000 [#1] PREEMPT SMP KASAN NOPTI CPU: 4 PID: 73 Comm: kworker/4:1 Not tainted 6.10.0-rc1 #4 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 Workqueue: xfs-inodegc/loop5 xfs_inodegc_worker [xfs] RIP: 0010:assfail (fs/xfs/xfs_message.c:102) xfs RSP: 0018:ffff88810188f7f0 EFLAGS: 00010202 RAX: 0000000000000000 RBX: ffff88816e748250 RCX: 1ffffffff844b0e7 RDX: 0000000000000004 RSI: ffff88810188f558 RDI: ffffffffc2431fa0 RBP: 1ffff11020311f01 R08: 0000000042431f9f R09: ffffed1020311e9b R10: ffff88810188f4df R11: ffffffffac725d70 R12: ffff88817a3f4000 R13: ffff88812182f000 R14: ffff88810188f998 R15: ffffffffc2423f80 FS: 0000000000000000(0000) GS:ffff8881c8400000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000055fe9d0f109c CR3: 000000014426c002 CR4: 0000000000770ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe07f0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: <TASK> xfs_trans_read_buf_map (fs/xfs/xfs_trans_buf.c:241 (discriminator 1)) xfs xfs_imap_to_bp (fs/xfs/xfs_trans.h:210 fs/xfs/libxfs/xfs_inode_buf.c:138) xfs xfs_inode_item_precommit (fs/xfs/xfs_inode_item.c:145) xfs xfs_trans_run_precommits (fs/xfs/xfs_trans.c:931) xfs __xfs_trans_commit (fs/xfs/xfs_trans.c:966) xfs xfs_inactive_ifree (fs/xfs/xfs_inode.c:1811) xfs xfs_inactive (fs/xfs/xfs_inode.c:2013) xfs xfs_inodegc_worker (fs/xfs/xfs_icache.c:1841 fs/xfs/xfs_icache.c:1886) xfs process_one_work (kernel/workqueue.c:3231) worker_thread (kernel/workqueue.c:3306 (discriminator 2) kernel/workqueue.c:3393 (discriminator 2)) kthread (kernel/kthread.c:389) ret_from_fork (arch/x86/kernel/process.c:147) ret_from_fork_asm (arch/x86/entry/entry_64.S:257) </TASK> And occurs when the the inode precommit handlers is attempt to look up the inode cluster buffer to attach the inode for writeback. The trail of logic that I can reconstruct is as follows. 1. the inode is clean when inodegc runs, so it is not attached to a cluster buffer when precommit runs. 2. #1 implies the inode cluster buffer may be clean and not pinned by dirty inodes when inodegc runs. 3. #2 implies that the inode cluster buffer can be reclaimed by memory pressure at any time. 4. The assert failure implies that the cluster buffer was attached to the transaction, but not marked done. It had been accessed earlier in the transaction, but not marked done. 5. #4 implies the cluster buffer has been invalidated (i.e. marked stale). 6. #5 implies that the inode cluster buffer was instantiated uninitialised in the transaction in xfs_ifree_cluster(), which only instantiates the buffers to invalidate them and never marks them as done. Given factors 1-3, this issue is highly dependent on timing and environmental factors. Hence the issue can be very difficult to reproduce in some situations, but highly reliable in others. Luis has an environment where it can be reproduced easily by g/531 but, OTOH, I've reproduced it only once in ~2000 cycles of g/531. I think the fix is to have xfs_ifree_cluster() set the XBF_DONE flag on the cluster buffers, even though they may not be initialised. The reasons why I think this is safe are: 1. A buffer cache lookup hit on a XBF_STALE buffer will clear the XBF_DONE flag. Hence all future users of the buffer know they have to re-initialise the contents before use and mark it done themselves. 2. xfs_trans_binval() sets the XFS_BLI_STALE flag, which means the buffer remains locked until the journal commit completes and the buffer is unpinned. Hence once marked XBF_STALE/XFS_BLI_STALE by xfs_ifree_cluster(), the only context that can access the freed buffer is the currently running transaction. 3. #2 implies that future buffer lookups in the currently running transaction will hit the transaction match code and not the buffer cache. Hence XBF_STALE and XFS_BLI_STALE will not be cleared unless the transaction initialises and logs the buffer with valid contents again. At which point, the buffer will be marked marked XBF_DONE again, so having XBF_DONE already set on the stale buffer is a moot point. 4. #2 also implies that any concurrent access to that cluster buffer will block waiting on the buffer lock until the inode cluster has been fully freed and is no longer an active inode cluster buffer. 5. #4 + #1 means that any future user of the disk range of that buffer will always see the range of disk blocks covered by the cluster buffer as not done, and hence must initialise the contents themselves. 6. Setting XBF_DONE in xfs_ifree_cluster() then means the unlinked inode precommit code will see a XBF_DONE buffer from the transaction match as it expects. It can then attach the stale but newly dirtied inode to the stale but newly dirtied cluster buffer without unexpected failures. The stale buffer will then sail through the journal and do the right thing with the attached stale inode during unpin. Hence the fix is just one line of extra code. The explanation of why we have to set XBF_DONE in xfs_ifree_cluster, OTOH, is long and complex.... Fixes: 82842fe ("xfs: fix AGF vs inode cluster buffer deadlock") Signed-off-by: Dave Chinner <dchinner@redhat.com> Tested-by: Luis Chamberlain <mcgrof@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Chandan Babu R <chandanbabu@kernel.org> Signed-off-by: Catherine Hoang <catherine.hoang@oracle.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3d04139 upstream. Syzkaller reported a lockdep splat: ============================================ WARNING: possible recursive locking detected 6.11.0-rc6-syzkaller-00019-g67784a74e258 #0 Not tainted -------------------------------------------- syz-executor364/5113 is trying to acquire lock: ffff8880449f1958 (k-slock-AF_INET){+.-.}-{2:2}, at: spin_lock include/linux/spinlock.h:351 [inline] ffff8880449f1958 (k-slock-AF_INET){+.-.}-{2:2}, at: sk_clone_lock+0x2cd/0xf40 net/core/sock.c:2328 but task is already holding lock: ffff88803fe3cb58 (k-slock-AF_INET){+.-.}-{2:2}, at: spin_lock include/linux/spinlock.h:351 [inline] ffff88803fe3cb58 (k-slock-AF_INET){+.-.}-{2:2}, at: sk_clone_lock+0x2cd/0xf40 net/core/sock.c:2328 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(k-slock-AF_INET); lock(k-slock-AF_INET); *** DEADLOCK *** May be due to missing lock nesting notation 7 locks held by syz-executor364/5113: #0: ffff8880449f0e18 (sk_lock-AF_INET){+.+.}-{0:0}, at: lock_sock include/net/sock.h:1607 [inline] #0: ffff8880449f0e18 (sk_lock-AF_INET){+.+.}-{0:0}, at: mptcp_sendmsg+0x153/0x1b10 net/mptcp/protocol.c:1806 #1: ffff88803fe39ad8 (k-sk_lock-AF_INET){+.+.}-{0:0}, at: lock_sock include/net/sock.h:1607 [inline] #1: ffff88803fe39ad8 (k-sk_lock-AF_INET){+.+.}-{0:0}, at: mptcp_sendmsg_fastopen+0x11f/0x530 net/mptcp/protocol.c:1727 #2: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: rcu_lock_acquire include/linux/rcupdate.h:326 [inline] #2: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: rcu_read_lock include/linux/rcupdate.h:838 [inline] #2: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: __ip_queue_xmit+0x5f/0x1b80 net/ipv4/ip_output.c:470 #3: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: rcu_lock_acquire include/linux/rcupdate.h:326 [inline] #3: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: rcu_read_lock include/linux/rcupdate.h:838 [inline] #3: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: ip_finish_output2+0x45f/0x1390 net/ipv4/ip_output.c:228 #4: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: local_lock_acquire include/linux/local_lock_internal.h:29 [inline] #4: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: process_backlog+0x33b/0x15b0 net/core/dev.c:6104 #5: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: rcu_lock_acquire include/linux/rcupdate.h:326 [inline] #5: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: rcu_read_lock include/linux/rcupdate.h:838 [inline] #5: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: ip_local_deliver_finish+0x230/0x5f0 net/ipv4/ip_input.c:232 #6: ffff88803fe3cb58 (k-slock-AF_INET){+.-.}-{2:2}, at: spin_lock include/linux/spinlock.h:351 [inline] #6: ffff88803fe3cb58 (k-slock-AF_INET){+.-.}-{2:2}, at: sk_clone_lock+0x2cd/0xf40 net/core/sock.c:2328 stack backtrace: CPU: 0 UID: 0 PID: 5113 Comm: syz-executor364 Not tainted 6.11.0-rc6-syzkaller-00019-g67784a74e258 #0 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014 Call Trace: <IRQ> __dump_stack lib/dump_stack.c:93 [inline] dump_stack_lvl+0x241/0x360 lib/dump_stack.c:119 check_deadlock kernel/locking/lockdep.c:3061 [inline] validate_chain+0x15d3/0x5900 kernel/locking/lockdep.c:3855 __lock_acquire+0x137a/0x2040 kernel/locking/lockdep.c:5142 lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5759 __raw_spin_lock include/linux/spinlock_api_smp.h:133 [inline] _raw_spin_lock+0x2e/0x40 kernel/locking/spinlock.c:154 spin_lock include/linux/spinlock.h:351 [inline] sk_clone_lock+0x2cd/0xf40 net/core/sock.c:2328 mptcp_sk_clone_init+0x32/0x13c0 net/mptcp/protocol.c:3279 subflow_syn_recv_sock+0x931/0x1920 net/mptcp/subflow.c:874 tcp_check_req+0xfe4/0x1a20 net/ipv4/tcp_minisocks.c:853 tcp_v4_rcv+0x1c3e/0x37f0 net/ipv4/tcp_ipv4.c:2267 ip_protocol_deliver_rcu+0x22e/0x440 net/ipv4/ip_input.c:205 ip_local_deliver_finish+0x341/0x5f0 net/ipv4/ip_input.c:233 NF_HOOK+0x3a4/0x450 include/linux/netfilter.h:314 NF_HOOK+0x3a4/0x450 include/linux/netfilter.h:314 __netif_receive_skb_one_core net/core/dev.c:5661 [inline] __netif_receive_skb+0x2bf/0x650 net/core/dev.c:5775 process_backlog+0x662/0x15b0 net/core/dev.c:6108 __napi_poll+0xcb/0x490 net/core/dev.c:6772 napi_poll net/core/dev.c:6841 [inline] net_rx_action+0x89b/0x1240 net/core/dev.c:6963 handle_softirqs+0x2c4/0x970 kernel/softirq.c:554 do_softirq+0x11b/0x1e0 kernel/softirq.c:455 </IRQ> <TASK> __local_bh_enable_ip+0x1bb/0x200 kernel/softirq.c:382 local_bh_enable include/linux/bottom_half.h:33 [inline] rcu_read_unlock_bh include/linux/rcupdate.h:908 [inline] __dev_queue_xmit+0x1763/0x3e90 net/core/dev.c:4450 dev_queue_xmit include/linux/netdevice.h:3105 [inline] neigh_hh_output include/net/neighbour.h:526 [inline] neigh_output include/net/neighbour.h:540 [inline] ip_finish_output2+0xd41/0x1390 net/ipv4/ip_output.c:235 ip_local_out net/ipv4/ip_output.c:129 [inline] __ip_queue_xmit+0x118c/0x1b80 net/ipv4/ip_output.c:535 __tcp_transmit_skb+0x2544/0x3b30 net/ipv4/tcp_output.c:1466 tcp_rcv_synsent_state_process net/ipv4/tcp_input.c:6542 [inline] tcp_rcv_state_process+0x2c32/0x4570 net/ipv4/tcp_input.c:6729 tcp_v4_do_rcv+0x77d/0xc70 net/ipv4/tcp_ipv4.c:1934 sk_backlog_rcv include/net/sock.h:1111 [inline] __release_sock+0x214/0x350 net/core/sock.c:3004 release_sock+0x61/0x1f0 net/core/sock.c:3558 mptcp_sendmsg_fastopen+0x1ad/0x530 net/mptcp/protocol.c:1733 mptcp_sendmsg+0x1884/0x1b10 net/mptcp/protocol.c:1812 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg+0x1a6/0x270 net/socket.c:745 ____sys_sendmsg+0x525/0x7d0 net/socket.c:2597 ___sys_sendmsg net/socket.c:2651 [inline] __sys_sendmmsg+0x3b2/0x740 net/socket.c:2737 __do_sys_sendmmsg net/socket.c:2766 [inline] __se_sys_sendmmsg net/socket.c:2763 [inline] __x64_sys_sendmmsg+0xa0/0xb0 net/socket.c:2763 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f04fb13a6b9 Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 01 1a 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007ffd651f42d8 EFLAGS: 00000246 ORIG_RAX: 0000000000000133 RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 00007f04fb13a6b9 RDX: 0000000000000001 RSI: 0000000020000d00 RDI: 0000000000000004 RBP: 00007ffd651f4310 R08: 0000000000000001 R09: 0000000000000001 R10: 0000000020000080 R11: 0000000000000246 R12: 00000000000f4240 R13: 00007f04fb187449 R14: 00007ffd651f42f4 R15: 00007ffd651f4300 </TASK> As noted by Cong Wang, the splat is false positive, but the code path leading to the report is an unexpected one: a client is attempting an MPC handshake towards the in-kernel listener created by the in-kernel PM for a port based signal endpoint. Such connection will be never accepted; many of them can make the listener queue full and preventing the creation of MPJ subflow via such listener - its intended role. Explicitly detect this scenario at initial-syn time and drop the incoming MPC request. Fixes: 1729cf1 ("mptcp: create the listening socket for new port") Cc: stable@vger.kernel.org Reported-by: syzbot+f4aacdfef2c6a6529c3e@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=f4aacdfef2c6a6529c3e Cc: Cong Wang <cong.wang@bytedance.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Reviewed-by: Mat Martineau <martineau@kernel.org> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Link: https://patch.msgid.link/20241014-net-mptcp-mpc-port-endp-v2-1-7faea8e6b6ae@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> [ Conflicts in mib.[ch], because commit 6982826 ("mptcp: fallback to TCP after SYN+MPC drops"), and commit 27069e7 ("mptcp: disable active MPTCP in case of blackhole") are linked to new features, not available in this version. Resolving the conflicts is easy, simply adding the new lines declaring the new "endpoint attempt" MIB entry. ] Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

@strlen

[ Upstream commit 146b6f1 ] Under certain kernel configurations when building with Clang/LLVM, the compiler does not generate a return or jump as the terminator instruction for ip_vs_protocol_init(), triggering the following objtool warning during build time: vmlinux.o: warning: objtool: ip_vs_protocol_init() falls through to next function __initstub__kmod_ip_vs_rr__935_123_ip_vs_rr_init6() At runtime, this either causes an oops when trying to load the ipvs module or a boot-time panic if ipvs is built-in. This same issue has been reported by the Intel kernel test robot previously. Digging deeper into both LLVM and the kernel code reveals this to be a undefined behavior problem. ip_vs_protocol_init() uses a on-stack buffer of 64 chars to store the registered protocol names and leaves it uninitialized after definition. The function calls strnlen() when concatenating protocol names into the buffer. With CONFIG_FORTIFY_SOURCE strnlen() performs an extra step to check whether the last byte of the input char buffer is a null character (commit 3009f89 ("fortify: Allow strlen() and strnlen() to pass compile-time known lengths")). This, together with possibly other configurations, cause the following IR to be generated: define hidden i32 @ip_vs_protocol_init() local_unnamed_addr #5 section ".init.text" align 16 !kcfi_type !29 { %1 = alloca [64 x i8], align 16 ... 14: ; preds = %11 %15 = getelementptr inbounds i8, ptr %1, i64 63 %16 = load i8, ptr %15, align 1 %17 = tail call i1 @llvm.is.constant.i8(i8 %16) %18 = icmp eq i8 %16, 0 %19 = select i1 %17, i1 %18, i1 false br i1 %19, label %20, label %23 20: ; preds = %14 %21 = call i64 @strlen(ptr noundef nonnull dereferenceable(1) %1) #23 ... 23: ; preds = %14, %11, %20 %24 = call i64 @strnlen(ptr noundef nonnull dereferenceable(1) %1, i64 noundef 64) #24 ... } The above code calculates the address of the last char in the buffer (value %15) and then loads from it (value %16). Because the buffer is never initialized, the LLVM GVN pass marks value %16 as undefined: %13 = getelementptr inbounds i8, ptr %1, i64 63 br i1 undef, label %14, label %17 This gives later passes (SCCP, in particular) more DCE opportunities by propagating the undef value further, and eventually removes everything after the load on the uninitialized stack location: define hidden i32 @ip_vs_protocol_init() local_unnamed_addr #0 section ".init.text" align 16 !kcfi_type !11 { %1 = alloca [64 x i8], align 16 ... 12: ; preds = %11 %13 = getelementptr inbounds i8, ptr %1, i64 63 unreachable } In this way, the generated native code will just fall through to the next function, as LLVM does not generate any code for the unreachable IR instruction and leaves the function without a terminator. Zero the on-stack buffer to avoid this possible UB. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202402100205.PWXIz1ZK-lkp@intel.com/ Co-developed-by: Ruowen Qin <ruqin@redhat.com> Signed-off-by: Ruowen Qin <ruqin@redhat.com> Signed-off-by: Jinghao Jia <jinghao7@illinois.edu> Acked-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

commit ac01c8c upstream. AddressSanitizer found a use-after-free bug in the symbol code which manifested as 'perf top' segfaulting. ==1238389==ERROR: AddressSanitizer: heap-use-after-free on address 0x60b00c48844b at pc 0x5650d8035961 bp 0x7f751aaecc90 sp 0x7f751aaecc80 READ of size 1 at 0x60b00c48844b thread T193 #0 0x5650d8035960 in _sort__sym_cmp util/sort.c:310 #1 0x5650d8043744 in hist_entry__cmp util/hist.c:1286 #2 0x5650d8043951 in hists__findnew_entry util/hist.c:614 #3 0x5650d804568f in __hists__add_entry util/hist.c:754 #4 0x5650d8045bf9 in hists__add_entry util/hist.c:772 openbmc#5 0x5650d8045df1 in iter_add_single_normal_entry util/hist.c:997 openbmc#6 0x5650d8043326 in hist_entry_iter__add util/hist.c:1242 openbmc#7 0x5650d7ceeefe in perf_event__process_sample /home/matt/src/linux/tools/perf/builtin-top.c:845 openbmc#8 0x5650d7ceeefe in deliver_event /home/matt/src/linux/tools/perf/builtin-top.c:1208 openbmc#9 0x5650d7fdb51b in do_flush util/ordered-events.c:245 openbmc#10 0x5650d7fdb51b in __ordered_events__flush util/ordered-events.c:324 openbmc#11 0x5650d7ced743 in process_thread /home/matt/src/linux/tools/perf/builtin-top.c:1120 openbmc#12 0x7f757ef1f133 in start_thread nptl/pthread_create.c:442 openbmc#13 0x7f757ef9f7db in clone3 ../sysdeps/unix/sysv/linux/x86_64/clone3.S:81 When updating hist maps it's also necessary to update the hist symbol reference because the old one gets freed in map__put(). While this bug was probably introduced with 5c24b67 ("perf tools: Replace map->referenced & maps->removed_maps with map->refcnt"), the symbol objects were leaked until c087e94 ("perf machine: Fix refcount usage when processing PERF_RECORD_KSYMBOL") was merged so the bug was masked. Fixes: c087e94 ("perf machine: Fix refcount usage when processing PERF_RECORD_KSYMBOL") Reported-by: Yunzhao Li <yunzhao@cloudflare.com> Signed-off-by: Matt Fleming (Cloudflare) <matt@readmodwrite.com> Cc: Ian Rogers <irogers@google.com> Cc: kernel-team@cloudflare.com Cc: Namhyung Kim <namhyung@kernel.org> Cc: Riccardo Mancini <rickyman7@gmail.com> Cc: stable@vger.kernel.org # v5.13+ Link: https://lore.kernel.org/r/20240815142212.3834625-1-matt@readmodwrite.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 9af2efe upstream. The fields in the hist_entry are filled on-demand which means they only have meaningful values when relevant sort keys are used. So if neither of 'dso' nor 'sym' sort keys are used, the map/symbols in the hist entry can be garbage. So it shouldn't access it unconditionally. I got a segfault, when I wanted to see cgroup profiles. $ sudo perf record -a --all-cgroups --synth=cgroup true $ sudo perf report -s cgroup Program received signal SIGSEGV, Segmentation fault. 0x00005555557a8d90 in map__dso (map=0x0) at util/map.h:48 48 return RC_CHK_ACCESS(map)->dso; (gdb) bt #0 0x00005555557a8d90 in map__dso (map=0x0) at util/map.h:48 #1 0x00005555557aa39b in map__load (map=0x0) at util/map.c:344 #2 0x00005555557aa592 in map__find_symbol (map=0x0, addr=140736115941088) at util/map.c:385 #3 0x00005555557ef000 in hists__findnew_entry (hists=0x555556039d60, entry=0x7fffffffa4c0, al=0x7fffffffa8c0, sample_self=true) at util/hist.c:644 #4 0x00005555557ef61c in __hists__add_entry (hists=0x555556039d60, al=0x7fffffffa8c0, sym_parent=0x0, bi=0x0, mi=0x0, ki=0x0, block_info=0x0, sample=0x7fffffffaa90, sample_self=true, ops=0x0) at util/hist.c:761 openbmc#5 0x00005555557ef71f in hists__add_entry (hists=0x555556039d60, al=0x7fffffffa8c0, sym_parent=0x0, bi=0x0, mi=0x0, ki=0x0, sample=0x7fffffffaa90, sample_self=true) at util/hist.c:779 openbmc#6 0x00005555557f00fb in iter_add_single_normal_entry (iter=0x7fffffffa900, al=0x7fffffffa8c0) at util/hist.c:1015 openbmc#7 0x00005555557f09a7 in hist_entry_iter__add (iter=0x7fffffffa900, al=0x7fffffffa8c0, max_stack_depth=127, arg=0x7fffffffbce0) at util/hist.c:1260 openbmc#8 0x00005555555ba7ce in process_sample_event (tool=0x7fffffffbce0, event=0x7ffff7c14128, sample=0x7fffffffaa90, evsel=0x555556039ad0, machine=0x5555560388e8) at builtin-report.c:334 openbmc#9 0x00005555557b30c8 in evlist__deliver_sample (evlist=0x555556039010, tool=0x7fffffffbce0, event=0x7ffff7c14128, sample=0x7fffffffaa90, evsel=0x555556039ad0, machine=0x5555560388e8) at util/session.c:1232 openbmc#10 0x00005555557b32bc in machines__deliver_event (machines=0x5555560388e8, evlist=0x555556039010, event=0x7ffff7c14128, sample=0x7fffffffaa90, tool=0x7fffffffbce0, file_offset=110888, file_path=0x555556038ff0 "perf.data") at util/session.c:1271 openbmc#11 0x00005555557b3848 in perf_session__deliver_event (session=0x5555560386d0, event=0x7ffff7c14128, tool=0x7fffffffbce0, file_offset=110888, file_path=0x555556038ff0 "perf.data") at util/session.c:1354 openbmc#12 0x00005555557affaf in ordered_events__deliver_event (oe=0x555556038e60, event=0x555556135aa0) at util/session.c:132 openbmc#13 0x00005555557bb605 in do_flush (oe=0x555556038e60, show_progress=false) at util/ordered-events.c:245 openbmc#14 0x00005555557bb95c in __ordered_events__flush (oe=0x555556038e60, how=OE_FLUSH__ROUND, timestamp=0) at util/ordered-events.c:324 openbmc#15 0x00005555557bba46 in ordered_events__flush (oe=0x555556038e60, how=OE_FLUSH__ROUND) at util/ordered-events.c:342 openbmc#16 0x00005555557b1b3b in perf_event__process_finished_round (tool=0x7fffffffbce0, event=0x7ffff7c15bb8, oe=0x555556038e60) at util/session.c:780 openbmc#17 0x00005555557b3b27 in perf_session__process_user_event (session=0x5555560386d0, event=0x7ffff7c15bb8, file_offset=117688, file_path=0x555556038ff0 "perf.data") at util/session.c:1406 As you can see the entry->ms.map was NULL even if he->ms.map has a value. This is because 'sym' sort key is not given, so it cannot assume whether he->ms.sym and entry->ms.sym is the same. I only checked the 'sym' sort key here as it implies 'dso' behavior (so maps are the same). Fixes: ac01c8c ("perf hist: Update hist symbol when updating maps") Signed-off-by: Namhyung Kim <namhyung@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Matt Fleming <matt@readmodwrite.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Link: https://lore.kernel.org/r/20240826221045.1202305-2-namhyung@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

…tion to perf_sched__replay() [ Upstream commit c690786 ] The start_work_mutex and work_done_wait_mutex are used only for the 'perf sched replay'. Put their initialization in perf_sched__replay () to reduce unnecessary actions in other commands. Simple functional testing: # perf sched record perf bench sched messaging # Running 'sched/messaging' benchmark: # 20 sender and receiver processes per group # 10 groups == 400 processes run Total time: 0.197 [sec] [ perf record: Woken up 1 times to write data ] [ perf record: Captured and wrote 14.952 MB perf.data (134165 samples) ] # perf sched replay run measurement overhead: 108 nsecs sleep measurement overhead: 65658 nsecs the run test took 999991 nsecs the sleep test took 1079324 nsecs nr_run_events: 42378 nr_sleep_events: 43102 nr_wakeup_events: 31852 target-less wakeups: 17 multi-target wakeups: 712 task 0 ( swapper: 0), nr_events: 10451 task 1 ( swapper: 1), nr_events: 3 task 2 ( swapper: 2), nr_events: 1 <SNIP> task 717 ( sched-messaging: 74483), nr_events: 152 task 718 ( sched-messaging: 74484), nr_events: 1944 task 719 ( sched-messaging: 74485), nr_events: 73 task 720 ( sched-messaging: 74486), nr_events: 163 task 721 ( sched-messaging: 74487), nr_events: 942 task 722 ( sched-messaging: 74488), nr_events: 78 task 723 ( sched-messaging: 74489), nr_events: 1090 ------------------------------------------------------------ #1 : 1366.507, ravg: 1366.51, cpu: 7682.70 / 7682.70 #2 : 1410.072, ravg: 1370.86, cpu: 7723.88 / 7686.82 #3 : 1396.296, ravg: 1373.41, cpu: 7568.20 / 7674.96 #4 : 1381.019, ravg: 1374.17, cpu: 7531.81 / 7660.64 openbmc#5 : 1393.826, ravg: 1376.13, cpu: 7725.25 / 7667.11 openbmc#6 : 1401.581, ravg: 1378.68, cpu: 7594.82 / 7659.88 openbmc#7 : 1381.337, ravg: 1378.94, cpu: 7371.22 / 7631.01 openbmc#8 : 1373.842, ravg: 1378.43, cpu: 7894.92 / 7657.40 openbmc#9 : 1364.697, ravg: 1377.06, cpu: 7324.91 / 7624.15 openbmc#10 : 1363.613, ravg: 1375.72, cpu: 7209.55 / 7582.69 # echo $? 0 Signed-off-by: Yang Jihong <yangjihong1@huawei.com> Signed-off-by: Namhyung Kim <namhyung@kernel.org> Link: https://lore.kernel.org/r/20240206083228.172607-2-yangjihong1@huawei.com Stable-dep-of: 1a5efc9 ("libsubcmd: Don't free the usage string") Signed-off-by: Sasha Levin <sashal@kernel.org>

…f_sched__{lat|map|replay}() [ Upstream commit bd2cdf2 ] The curr_pid and cpu_last_switched are used only for the 'perf sched replay/latency/map'. Put their initialization in perf_sched__{lat|map|replay () to reduce unnecessary actions in other commands. Simple functional testing: # perf sched record perf bench sched messaging # Running 'sched/messaging' benchmark: # 20 sender and receiver processes per group # 10 groups == 400 processes run Total time: 0.209 [sec] [ perf record: Woken up 1 times to write data ] [ perf record: Captured and wrote 16.456 MB perf.data (147907 samples) ] # perf sched lat ------------------------------------------------------------------------------------------------------------------------------------------- Task | Runtime ms | Switches | Avg delay ms | Max delay ms | Max delay start | Max delay end | ------------------------------------------------------------------------------------------------------------------------------------------- sched-messaging:(401) | 2990.699 ms | 38705 | avg: 0.661 ms | max: 67.046 ms | max start: 456532.624830 s | max end: 456532.691876 s qemu-system-x86:(7) | 179.764 ms | 2191 | avg: 0.152 ms | max: 21.857 ms | max start: 456532.576434 s | max end: 456532.598291 s sshd:48125 | 0.522 ms | 2 | avg: 0.037 ms | max: 0.046 ms | max start: 456532.514610 s | max end: 456532.514656 s <SNIP> ksoftirqd/11:82 | 0.063 ms | 1 | avg: 0.005 ms | max: 0.005 ms | max start: 456532.769366 s | max end: 456532.769371 s kworker/9:0-mm_:34624 | 0.233 ms | 20 | avg: 0.004 ms | max: 0.007 ms | max start: 456532.690804 s | max end: 456532.690812 s migration/13:93 | 0.000 ms | 1 | avg: 0.004 ms | max: 0.004 ms | max start: 456532.512669 s | max end: 456532.512674 s ----------------------------------------------------------------------------------------------------------------- TOTAL: | 3180.750 ms | 41368 | --------------------------------------------------- # echo $? 0 # perf sched map *A0 456532.510141 secs A0 => migration/0:15 *. 456532.510171 secs . => swapper:0 . *B0 456532.510261 secs B0 => migration/1:21 . *. 456532.510279 secs <SNIP> L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 *L7 . . . . 456532.785979 secs L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 *L7 . . . 456532.786054 secs L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 *L7 . . 456532.786127 secs L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 *L7 . 456532.786197 secs L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 *L7 456532.786270 secs # echo $? 0 # perf sched replay run measurement overhead: 108 nsecs sleep measurement overhead: 66473 nsecs the run test took 1000002 nsecs the sleep test took 1082686 nsecs nr_run_events: 49334 nr_sleep_events: 50054 nr_wakeup_events: 34701 target-less wakeups: 165 multi-target wakeups: 766 task 0 ( swapper: 0), nr_events: 15419 task 1 ( swapper: 1), nr_events: 1 task 2 ( swapper: 2), nr_events: 1 <SNIP> task 715 ( sched-messaging: 110248), nr_events: 1438 task 716 ( sched-messaging: 110249), nr_events: 512 task 717 ( sched-messaging: 110250), nr_events: 500 task 718 ( sched-messaging: 110251), nr_events: 537 task 719 ( sched-messaging: 110252), nr_events: 823 ------------------------------------------------------------ #1 : 1325.288, ravg: 1325.29, cpu: 7823.35 / 7823.35 #2 : 1363.606, ravg: 1329.12, cpu: 7655.53 / 7806.56 #3 : 1349.494, ravg: 1331.16, cpu: 7544.80 / 7780.39 #4 : 1311.488, ravg: 1329.19, cpu: 7495.13 / 7751.86 openbmc#5 : 1309.902, ravg: 1327.26, cpu: 7266.65 / 7703.34 openbmc#6 : 1309.535, ravg: 1325.49, cpu: 7843.86 / 7717.39 openbmc#7 : 1316.482, ravg: 1324.59, cpu: 7854.41 / 7731.09 openbmc#8 : 1366.604, ravg: 1328.79, cpu: 7955.81 / 7753.57 openbmc#9 : 1326.286, ravg: 1328.54, cpu: 7466.86 / 7724.90 openbmc#10 : 1356.653, ravg: 1331.35, cpu: 7566.60 / 7709.07 # echo $? 0 Signed-off-by: Yang Jihong <yangjihong1@huawei.com> Signed-off-by: Namhyung Kim <namhyung@kernel.org> Link: https://lore.kernel.org/r/20240206083228.172607-5-yangjihong1@huawei.com Stable-dep-of: 1a5efc9 ("libsubcmd: Don't free the usage string") Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a848c29 ] On the node of an NFS client, some files saved in the mountpoint of the NFS server were copied to another location of the same NFS server. Accidentally, the nfs42_complete_copies() got a NULL-pointer dereference crash with the following syslog: [232064.838881] NFSv4: state recovery failed for open file nfs/pvc-12b5200d-cd0f-46a3-b9f0-af8f4fe0ef64.qcow2, error = -116 [232064.839360] NFSv4: state recovery failed for open file nfs/pvc-12b5200d-cd0f-46a3-b9f0-af8f4fe0ef64.qcow2, error = -116 [232066.588183] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000058 [232066.588586] Mem abort info: [232066.588701] ESR = 0x0000000096000007 [232066.588862] EC = 0x25: DABT (current EL), IL = 32 bits [232066.589084] SET = 0, FnV = 0 [232066.589216] EA = 0, S1PTW = 0 [232066.589340] FSC = 0x07: level 3 translation fault [232066.589559] Data abort info: [232066.589683] ISV = 0, ISS = 0x00000007 [232066.589842] CM = 0, WnR = 0 [232066.589967] user pgtable: 64k pages, 48-bit VAs, pgdp=00002000956ff400 [232066.590231] [0000000000000058] pgd=08001100ae100003, p4d=08001100ae100003, pud=08001100ae100003, pmd=08001100b3c00003, pte=0000000000000000 [232066.590757] Internal error: Oops: 96000007 [#1] SMP [232066.590958] Modules linked in: rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver nfs lockd grace fscache netfs ocfs2_dlmfs ocfs2_stack_o2cb ocfs2_dlm vhost_net vhost vhost_iotlb tap tun ipt_rpfilter xt_multiport ip_set_hash_ip ip_set_hash_net xfrm_interface xfrm6_tunnel tunnel4 tunnel6 esp4 ah4 wireguard libcurve25519_generic veth xt_addrtype xt_set nf_conntrack_netlink ip_set_hash_ipportnet ip_set_hash_ipportip ip_set_bitmap_port ip_set_hash_ipport dummy ip_set ip_vs_sh ip_vs_wrr ip_vs_rr ip_vs iptable_filter sch_ingress nfnetlink_cttimeout vport_gre ip_gre ip_tunnel gre vport_geneve geneve vport_vxlan vxlan ip6_udp_tunnel udp_tunnel openvswitch nf_conncount dm_round_robin dm_service_time dm_multipath xt_nat xt_MASQUERADE nft_chain_nat nf_nat xt_mark xt_conntrack xt_comment nft_compat nft_counter nf_tables nfnetlink ocfs2 ocfs2_nodemanager ocfs2_stackglue iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi ipmi_ssif nbd overlay 8021q garp mrp bonding tls rfkill sunrpc ext4 mbcache jbd2 [232066.591052] vfat fat cas_cache cas_disk ses enclosure scsi_transport_sas sg acpi_ipmi ipmi_si ipmi_devintf ipmi_msghandler ip_tables vfio_pci vfio_pci_core vfio_virqfd vfio_iommu_type1 vfio dm_mirror dm_region_hash dm_log dm_mod nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 br_netfilter bridge stp llc fuse xfs libcrc32c ast drm_vram_helper qla2xxx drm_kms_helper syscopyarea crct10dif_ce sysfillrect ghash_ce sysimgblt sha2_ce fb_sys_fops cec sha256_arm64 sha1_ce drm_ttm_helper ttm nvme_fc igb sbsa_gwdt nvme_fabrics drm nvme_core i2c_algo_bit i40e scsi_transport_fc megaraid_sas aes_neon_bs [232066.596953] CPU: 6 PID: 4124696 Comm: 10.253.166.125- Kdump: loaded Not tainted 5.15.131-9.cl9_ocfs2.aarch64 #1 [232066.597356] Hardware name: Great Wall .\x93\x8e...RF6260 V5/GWMSSE2GL1T, BIOS T656FBE_V3.0.18 2024-01-06 [232066.597721] pstate: 20400009 (nzCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [232066.598034] pc : nfs4_reclaim_open_state+0x220/0x800 [nfsv4] [232066.598327] lr : nfs4_reclaim_open_state+0x12c/0x800 [nfsv4] [232066.598595] sp : ffff8000f568fc70 [232066.598731] x29: ffff8000f568fc70 x28: 0000000000001000 x27: ffff21003db33000 [232066.599030] x26: ffff800005521ae0 x25: ffff0100f98fa3f0 x24: 0000000000000001 [232066.599319] x23: ffff800009920008 x22: ffff21003db33040 x21: ffff21003db33050 [232066.599628] x20: ffff410172fe9e40 x19: ffff410172fe9e00 x18: 0000000000000000 [232066.599914] x17: 0000000000000000 x16: 0000000000000004 x15: 0000000000000000 [232066.600195] x14: 0000000000000000 x13: ffff800008e685a8 x12: 00000000eac0c6e6 [232066.600498] x11: 0000000000000000 x10: 0000000000000008 x9 : ffff8000054e5828 [232066.600784] x8 : 00000000ffffffbf x7 : 0000000000000001 x6 : 000000000a9eb14a [232066.601062] x5 : 0000000000000000 x4 : ffff70ff8a14a800 x3 : 0000000000000058 [232066.601348] x2 : 0000000000000001 x1 : 54dce46366daa6c6 x0 : 0000000000000000 [232066.601636] Call trace: [232066.601749] nfs4_reclaim_open_state+0x220/0x800 [nfsv4] [232066.601998] nfs4_do_reclaim+0x1b8/0x28c [nfsv4] [232066.602218] nfs4_state_manager+0x928/0x10f0 [nfsv4] [232066.602455] nfs4_run_state_manager+0x78/0x1b0 [nfsv4] [232066.602690] kthread+0x110/0x114 [232066.602830] ret_from_fork+0x10/0x20 [232066.602985] Code: 1400000d f9403f20 f9402e61 91016003 (f9402c00) [232066.603284] SMP: stopping secondary CPUs [232066.606936] Starting crashdump kernel... [232066.607146] Bye! Analysing the vmcore, we know that nfs4_copy_state listed by destination nfs_server->ss_copies was added by the field copies in handle_async_copy(), and we found a waiting copy process with the stack as: PID: 3511963 TASK: ffff710028b47e00 CPU: 0 COMMAND: "cp" #0 [ffff8001116ef740] __switch_to at ffff8000081b92f4 #1 [ffff8001116ef760] __schedule at ffff800008dd0650 #2 [ffff8001116ef7c0] schedule at ffff800008dd0a00 #3 [ffff8001116ef7e0] schedule_timeout at ffff800008dd6aa0 #4 [ffff8001116ef860] __wait_for_common at ffff800008dd166c openbmc#5 [ffff8001116ef8e0] wait_for_completion_interruptible at ffff800008dd1898 openbmc#6 [ffff8001116ef8f0] handle_async_copy at ffff8000055142f4 [nfsv4] openbmc#7 [ffff8001116ef970] _nfs42_proc_copy at ffff8000055147c8 [nfsv4] openbmc#8 [ffff8001116efa80] nfs42_proc_copy at ffff800005514cf0 [nfsv4] openbmc#9 [ffff8001116efc50] __nfs4_copy_file_range.constprop.0 at ffff8000054ed694 [nfsv4] The NULL-pointer dereference was due to nfs42_complete_copies() listed the nfs_server->ss_copies by the field ss_copies of nfs4_copy_state. So the nfs4_copy_state address ffff0100f98fa3f0 was offset by 0x10 and the data accessed through this pointer was also incorrect. Generally, the ordered list nfs4_state_owner->so_states indicate open(O_RDWR) or open(O_WRITE) states are reclaimed firstly by nfs4_reclaim_open_state(). When destination state reclaim is failed with NFS_STATE_RECOVERY_FAILED and copies are not deleted in nfs_server->ss_copies, the source state may be passed to the nfs42_complete_copies() process earlier, resulting in this crash scene finally. To solve this issue, we add a list_head nfs_server->ss_src_copies for a server-to-server copy specially. Fixes: 0e65a32 ("NFS: handle source server reboot") Signed-off-by: Yanjun Zhang <zhangyanjun@cestc.cn> Reviewed-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

…ation commit c728a95 upstream. When testing the XDP_REDIRECT function on the LS1028A platform, we found a very reproducible issue that the Tx frames can no longer be sent out even if XDP_REDIRECT is turned off. Specifically, if there is a lot of traffic on Rx direction, when XDP_REDIRECT is turned on, the console may display some warnings like "timeout for tx ring openbmc#6 clear", and all redirected frames will be dropped, the detailed log is as follows. root@ls1028ardb:~# ./xdp-bench redirect eno0 eno2 Redirecting from eno0 (ifindex 3; driver fsl_enetc) to eno2 (ifindex 4; driver fsl_enetc) [203.849809] fsl_enetc 0000:00:00.2 eno2: timeout for tx ring openbmc#5 clear [204.006051] fsl_enetc 0000:00:00.2 eno2: timeout for tx ring openbmc#6 clear [204.161944] fsl_enetc 0000:00:00.2 eno2: timeout for tx ring openbmc#7 clear eno0->eno2 1420505 rx/s 1420590 err,drop/s 0 xmit/s xmit eno0->eno2 0 xmit/s 1420590 drop/s 0 drv_err/s 15.71 bulk-avg eno0->eno2 1420484 rx/s 1420485 err,drop/s 0 xmit/s xmit eno0->eno2 0 xmit/s 1420485 drop/s 0 drv_err/s 15.71 bulk-avg By analyzing the XDP_REDIRECT implementation of enetc driver, the driver will reconfigure Tx and Rx BD rings when a bpf program is installed or uninstalled, but there is no mechanisms to block the redirected frames when enetc driver reconfigures rings. Similarly, XDP_TX verdicts on received frames can also lead to frames being enqueued in the Tx rings. Because XDP ignores the state set by the netif_tx_wake_queue() API, so introduce the ENETC_TX_DOWN flag to suppress transmission of XDP frames. Fixes: c33bfaf ("net: enetc: set up XDP program under enetc_reconfigure()") Cc: stable@vger.kernel.org Signed-off-by: Wei Fang <wei.fang@nxp.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://patch.msgid.link/20241010092056.298128-3-wei.fang@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 348a198 upstream. Luis has been reporting an assert failure when freeing an inode cluster during inode inactivation for a while. The assert looks like: XFS: Assertion failed: bp->b_flags & XBF_DONE, file: fs/xfs/xfs_trans_buf.c, line: 241 ------------[ cut here ]------------ kernel BUG at fs/xfs/xfs_message.c:102! Oops: invalid opcode: 0000 [#1] PREEMPT SMP KASAN NOPTI CPU: 4 PID: 73 Comm: kworker/4:1 Not tainted 6.10.0-rc1 #4 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 Workqueue: xfs-inodegc/loop5 xfs_inodegc_worker [xfs] RIP: 0010:assfail (fs/xfs/xfs_message.c:102) xfs RSP: 0018:ffff88810188f7f0 EFLAGS: 00010202 RAX: 0000000000000000 RBX: ffff88816e748250 RCX: 1ffffffff844b0e7 RDX: 0000000000000004 RSI: ffff88810188f558 RDI: ffffffffc2431fa0 RBP: 1ffff11020311f01 R08: 0000000042431f9f R09: ffffed1020311e9b R10: ffff88810188f4df R11: ffffffffac725d70 R12: ffff88817a3f4000 R13: ffff88812182f000 R14: ffff88810188f998 R15: ffffffffc2423f80 FS: 0000000000000000(0000) GS:ffff8881c8400000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000055fe9d0f109c CR3: 000000014426c002 CR4: 0000000000770ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe07f0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: <TASK> xfs_trans_read_buf_map (fs/xfs/xfs_trans_buf.c:241 (discriminator 1)) xfs xfs_imap_to_bp (fs/xfs/xfs_trans.h:210 fs/xfs/libxfs/xfs_inode_buf.c:138) xfs xfs_inode_item_precommit (fs/xfs/xfs_inode_item.c:145) xfs xfs_trans_run_precommits (fs/xfs/xfs_trans.c:931) xfs __xfs_trans_commit (fs/xfs/xfs_trans.c:966) xfs xfs_inactive_ifree (fs/xfs/xfs_inode.c:1811) xfs xfs_inactive (fs/xfs/xfs_inode.c:2013) xfs xfs_inodegc_worker (fs/xfs/xfs_icache.c:1841 fs/xfs/xfs_icache.c:1886) xfs process_one_work (kernel/workqueue.c:3231) worker_thread (kernel/workqueue.c:3306 (discriminator 2) kernel/workqueue.c:3393 (discriminator 2)) kthread (kernel/kthread.c:389) ret_from_fork (arch/x86/kernel/process.c:147) ret_from_fork_asm (arch/x86/entry/entry_64.S:257) </TASK> And occurs when the the inode precommit handlers is attempt to look up the inode cluster buffer to attach the inode for writeback. The trail of logic that I can reconstruct is as follows. 1. the inode is clean when inodegc runs, so it is not attached to a cluster buffer when precommit runs. 2. #1 implies the inode cluster buffer may be clean and not pinned by dirty inodes when inodegc runs. 3. #2 implies that the inode cluster buffer can be reclaimed by memory pressure at any time. 4. The assert failure implies that the cluster buffer was attached to the transaction, but not marked done. It had been accessed earlier in the transaction, but not marked done. 5. #4 implies the cluster buffer has been invalidated (i.e. marked stale). 6. openbmc#5 implies that the inode cluster buffer was instantiated uninitialised in the transaction in xfs_ifree_cluster(), which only instantiates the buffers to invalidate them and never marks them as done. Given factors 1-3, this issue is highly dependent on timing and environmental factors. Hence the issue can be very difficult to reproduce in some situations, but highly reliable in others. Luis has an environment where it can be reproduced easily by g/531 but, OTOH, I've reproduced it only once in ~2000 cycles of g/531. I think the fix is to have xfs_ifree_cluster() set the XBF_DONE flag on the cluster buffers, even though they may not be initialised. The reasons why I think this is safe are: 1. A buffer cache lookup hit on a XBF_STALE buffer will clear the XBF_DONE flag. Hence all future users of the buffer know they have to re-initialise the contents before use and mark it done themselves. 2. xfs_trans_binval() sets the XFS_BLI_STALE flag, which means the buffer remains locked until the journal commit completes and the buffer is unpinned. Hence once marked XBF_STALE/XFS_BLI_STALE by xfs_ifree_cluster(), the only context that can access the freed buffer is the currently running transaction. 3. #2 implies that future buffer lookups in the currently running transaction will hit the transaction match code and not the buffer cache. Hence XBF_STALE and XFS_BLI_STALE will not be cleared unless the transaction initialises and logs the buffer with valid contents again. At which point, the buffer will be marked marked XBF_DONE again, so having XBF_DONE already set on the stale buffer is a moot point. 4. #2 also implies that any concurrent access to that cluster buffer will block waiting on the buffer lock until the inode cluster has been fully freed and is no longer an active inode cluster buffer. 5. #4 + #1 means that any future user of the disk range of that buffer will always see the range of disk blocks covered by the cluster buffer as not done, and hence must initialise the contents themselves. 6. Setting XBF_DONE in xfs_ifree_cluster() then means the unlinked inode precommit code will see a XBF_DONE buffer from the transaction match as it expects. It can then attach the stale but newly dirtied inode to the stale but newly dirtied cluster buffer without unexpected failures. The stale buffer will then sail through the journal and do the right thing with the attached stale inode during unpin. Hence the fix is just one line of extra code. The explanation of why we have to set XBF_DONE in xfs_ifree_cluster, OTOH, is long and complex.... Fixes: 82842fe ("xfs: fix AGF vs inode cluster buffer deadlock") Signed-off-by: Dave Chinner <dchinner@redhat.com> Tested-by: Luis Chamberlain <mcgrof@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Chandan Babu R <chandanbabu@kernel.org> Signed-off-by: Catherine Hoang <catherine.hoang@oracle.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3d04139 upstream. Syzkaller reported a lockdep splat: ============================================ WARNING: possible recursive locking detected 6.11.0-rc6-syzkaller-00019-g67784a74e258 #0 Not tainted -------------------------------------------- syz-executor364/5113 is trying to acquire lock: ffff8880449f1958 (k-slock-AF_INET){+.-.}-{2:2}, at: spin_lock include/linux/spinlock.h:351 [inline] ffff8880449f1958 (k-slock-AF_INET){+.-.}-{2:2}, at: sk_clone_lock+0x2cd/0xf40 net/core/sock.c:2328 but task is already holding lock: ffff88803fe3cb58 (k-slock-AF_INET){+.-.}-{2:2}, at: spin_lock include/linux/spinlock.h:351 [inline] ffff88803fe3cb58 (k-slock-AF_INET){+.-.}-{2:2}, at: sk_clone_lock+0x2cd/0xf40 net/core/sock.c:2328 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(k-slock-AF_INET); lock(k-slock-AF_INET); *** DEADLOCK *** May be due to missing lock nesting notation 7 locks held by syz-executor364/5113: #0: ffff8880449f0e18 (sk_lock-AF_INET){+.+.}-{0:0}, at: lock_sock include/net/sock.h:1607 [inline] #0: ffff8880449f0e18 (sk_lock-AF_INET){+.+.}-{0:0}, at: mptcp_sendmsg+0x153/0x1b10 net/mptcp/protocol.c:1806 #1: ffff88803fe39ad8 (k-sk_lock-AF_INET){+.+.}-{0:0}, at: lock_sock include/net/sock.h:1607 [inline] #1: ffff88803fe39ad8 (k-sk_lock-AF_INET){+.+.}-{0:0}, at: mptcp_sendmsg_fastopen+0x11f/0x530 net/mptcp/protocol.c:1727 #2: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: rcu_lock_acquire include/linux/rcupdate.h:326 [inline] #2: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: rcu_read_lock include/linux/rcupdate.h:838 [inline] #2: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: __ip_queue_xmit+0x5f/0x1b80 net/ipv4/ip_output.c:470 #3: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: rcu_lock_acquire include/linux/rcupdate.h:326 [inline] #3: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: rcu_read_lock include/linux/rcupdate.h:838 [inline] #3: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: ip_finish_output2+0x45f/0x1390 net/ipv4/ip_output.c:228 #4: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: local_lock_acquire include/linux/local_lock_internal.h:29 [inline] #4: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: process_backlog+0x33b/0x15b0 net/core/dev.c:6104 openbmc#5: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: rcu_lock_acquire include/linux/rcupdate.h:326 [inline] openbmc#5: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: rcu_read_lock include/linux/rcupdate.h:838 [inline] openbmc#5: ffffffff8e938320 (rcu_read_lock){....}-{1:2}, at: ip_local_deliver_finish+0x230/0x5f0 net/ipv4/ip_input.c:232 openbmc#6: ffff88803fe3cb58 (k-slock-AF_INET){+.-.}-{2:2}, at: spin_lock include/linux/spinlock.h:351 [inline] openbmc#6: ffff88803fe3cb58 (k-slock-AF_INET){+.-.}-{2:2}, at: sk_clone_lock+0x2cd/0xf40 net/core/sock.c:2328 stack backtrace: CPU: 0 UID: 0 PID: 5113 Comm: syz-executor364 Not tainted 6.11.0-rc6-syzkaller-00019-g67784a74e258 #0 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014 Call Trace: <IRQ> __dump_stack lib/dump_stack.c:93 [inline] dump_stack_lvl+0x241/0x360 lib/dump_stack.c:119 check_deadlock kernel/locking/lockdep.c:3061 [inline] validate_chain+0x15d3/0x5900 kernel/locking/lockdep.c:3855 __lock_acquire+0x137a/0x2040 kernel/locking/lockdep.c:5142 lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5759 __raw_spin_lock include/linux/spinlock_api_smp.h:133 [inline] _raw_spin_lock+0x2e/0x40 kernel/locking/spinlock.c:154 spin_lock include/linux/spinlock.h:351 [inline] sk_clone_lock+0x2cd/0xf40 net/core/sock.c:2328 mptcp_sk_clone_init+0x32/0x13c0 net/mptcp/protocol.c:3279 subflow_syn_recv_sock+0x931/0x1920 net/mptcp/subflow.c:874 tcp_check_req+0xfe4/0x1a20 net/ipv4/tcp_minisocks.c:853 tcp_v4_rcv+0x1c3e/0x37f0 net/ipv4/tcp_ipv4.c:2267 ip_protocol_deliver_rcu+0x22e/0x440 net/ipv4/ip_input.c:205 ip_local_deliver_finish+0x341/0x5f0 net/ipv4/ip_input.c:233 NF_HOOK+0x3a4/0x450 include/linux/netfilter.h:314 NF_HOOK+0x3a4/0x450 include/linux/netfilter.h:314 __netif_receive_skb_one_core net/core/dev.c:5661 [inline] __netif_receive_skb+0x2bf/0x650 net/core/dev.c:5775 process_backlog+0x662/0x15b0 net/core/dev.c:6108 __napi_poll+0xcb/0x490 net/core/dev.c:6772 napi_poll net/core/dev.c:6841 [inline] net_rx_action+0x89b/0x1240 net/core/dev.c:6963 handle_softirqs+0x2c4/0x970 kernel/softirq.c:554 do_softirq+0x11b/0x1e0 kernel/softirq.c:455 </IRQ> <TASK> __local_bh_enable_ip+0x1bb/0x200 kernel/softirq.c:382 local_bh_enable include/linux/bottom_half.h:33 [inline] rcu_read_unlock_bh include/linux/rcupdate.h:908 [inline] __dev_queue_xmit+0x1763/0x3e90 net/core/dev.c:4450 dev_queue_xmit include/linux/netdevice.h:3105 [inline] neigh_hh_output include/net/neighbour.h:526 [inline] neigh_output include/net/neighbour.h:540 [inline] ip_finish_output2+0xd41/0x1390 net/ipv4/ip_output.c:235 ip_local_out net/ipv4/ip_output.c:129 [inline] __ip_queue_xmit+0x118c/0x1b80 net/ipv4/ip_output.c:535 __tcp_transmit_skb+0x2544/0x3b30 net/ipv4/tcp_output.c:1466 tcp_rcv_synsent_state_process net/ipv4/tcp_input.c:6542 [inline] tcp_rcv_state_process+0x2c32/0x4570 net/ipv4/tcp_input.c:6729 tcp_v4_do_rcv+0x77d/0xc70 net/ipv4/tcp_ipv4.c:1934 sk_backlog_rcv include/net/sock.h:1111 [inline] __release_sock+0x214/0x350 net/core/sock.c:3004 release_sock+0x61/0x1f0 net/core/sock.c:3558 mptcp_sendmsg_fastopen+0x1ad/0x530 net/mptcp/protocol.c:1733 mptcp_sendmsg+0x1884/0x1b10 net/mptcp/protocol.c:1812 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg+0x1a6/0x270 net/socket.c:745 ____sys_sendmsg+0x525/0x7d0 net/socket.c:2597 ___sys_sendmsg net/socket.c:2651 [inline] __sys_sendmmsg+0x3b2/0x740 net/socket.c:2737 __do_sys_sendmmsg net/socket.c:2766 [inline] __se_sys_sendmmsg net/socket.c:2763 [inline] __x64_sys_sendmmsg+0xa0/0xb0 net/socket.c:2763 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f04fb13a6b9 Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 01 1a 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007ffd651f42d8 EFLAGS: 00000246 ORIG_RAX: 0000000000000133 RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 00007f04fb13a6b9 RDX: 0000000000000001 RSI: 0000000020000d00 RDI: 0000000000000004 RBP: 00007ffd651f4310 R08: 0000000000000001 R09: 0000000000000001 R10: 0000000020000080 R11: 0000000000000246 R12: 00000000000f4240 R13: 00007f04fb187449 R14: 00007ffd651f42f4 R15: 00007ffd651f4300 </TASK> As noted by Cong Wang, the splat is false positive, but the code path leading to the report is an unexpected one: a client is attempting an MPC handshake towards the in-kernel listener created by the in-kernel PM for a port based signal endpoint. Such connection will be never accepted; many of them can make the listener queue full and preventing the creation of MPJ subflow via such listener - its intended role. Explicitly detect this scenario at initial-syn time and drop the incoming MPC request. Fixes: 1729cf1 ("mptcp: create the listening socket for new port") Cc: stable@vger.kernel.org Reported-by: syzbot+f4aacdfef2c6a6529c3e@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=f4aacdfef2c6a6529c3e Cc: Cong Wang <cong.wang@bytedance.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Reviewed-by: Mat Martineau <martineau@kernel.org> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Link: https://patch.msgid.link/20241014-net-mptcp-mpc-port-endp-v2-1-7faea8e6b6ae@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> [ Conflicts in mib.[ch], because commit 6982826 ("mptcp: fallback to TCP after SYN+MPC drops"), and commit 27069e7 ("mptcp: disable active MPTCP in case of blackhole") are linked to new features, not available in this version. Resolving the conflicts is easy, simply adding the new lines declaring the new "endpoint attempt" MIB entry. ] Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

…nt message commit cddc76b upstream. Address a bug in the kernel that triggers a "sleeping function called from invalid context" warning when /sys/kernel/debug/kmemleak is printed under specific conditions: - CONFIG_PREEMPT_RT=y - Set SELinux as the LSM for the system - Set kptr_restrict to 1 - kmemleak buffer contains at least one item BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48 in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 136, name: cat preempt_count: 1, expected: 0 RCU nest depth: 2, expected: 2 6 locks held by cat/136: #0: ffff32e64bcbf950 (&p->lock){+.+.}-{3:3}, at: seq_read_iter+0xb8/0xe30 #1: ffffafe6aaa9dea0 (scan_mutex){+.+.}-{3:3}, at: kmemleak_seq_start+0x34/0x128 #3: ffff32e6546b1cd0 (&object->lock){....}-{2:2}, at: kmemleak_seq_show+0x3c/0x1e0 #4: ffffafe6aa8d8560 (rcu_read_lock){....}-{1:2}, at: has_ns_capability_noaudit+0x8/0x1b0 #5: ffffafe6aabbc0f8 (notif_lock){+.+.}-{2:2}, at: avc_compute_av+0xc4/0x3d0 irq event stamp: 136660 hardirqs last enabled at (136659): [<ffffafe6a80fd7a0>] _raw_spin_unlock_irqrestore+0xa8/0xd8 hardirqs last disabled at (136660): [<ffffafe6a80fd85c>] _raw_spin_lock_irqsave+0x8c/0xb0 softirqs last enabled at (0): [<ffffafe6a5d50b28>] copy_process+0x11d8/0x3df8 softirqs last disabled at (0): [<0000000000000000>] 0x0 Preemption disabled at: [<ffffafe6a6598a4c>] kmemleak_seq_show+0x3c/0x1e0 CPU: 1 UID: 0 PID: 136 Comm: cat Tainted: G E 6.11.0-rt7+ #34 Tainted: [E]=UNSIGNED_MODULE Hardware name: linux,dummy-virt (DT) Call trace: dump_backtrace+0xa0/0x128 show_stack+0x1c/0x30 dump_stack_lvl+0xe8/0x198 dump_stack+0x18/0x20 rt_spin_lock+0x8c/0x1a8 avc_perm_nonode+0xa0/0x150 cred_has_capability.isra.0+0x118/0x218 selinux_capable+0x50/0x80 security_capable+0x7c/0xd0 has_ns_capability_noaudit+0x94/0x1b0 has_capability_noaudit+0x20/0x30 restricted_pointer+0x21c/0x4b0 pointer+0x298/0x760 vsnprintf+0x330/0xf70 seq_printf+0x178/0x218 print_unreferenced+0x1a4/0x2d0 kmemleak_seq_show+0xd0/0x1e0 seq_read_iter+0x354/0xe30 seq_read+0x250/0x378 full_proxy_read+0xd8/0x148 vfs_read+0x190/0x918 ksys_read+0xf0/0x1e0 __arm64_sys_read+0x70/0xa8 invoke_syscall.constprop.0+0xd4/0x1d8 el0_svc+0x50/0x158 el0t_64_sync+0x17c/0x180 %pS and %pK, in the same back trace line, are redundant, and %pS can void %pK service in certain contexts. %pS alone already provides the necessary information, and if it cannot resolve the symbol, it falls back to printing the raw address voiding the original intent behind the %pK. Additionally, %pK requires a privilege check CAP_SYSLOG enforced through the LSM, which can trigger a "sleeping function called from invalid context" warning under RT_PREEMPT kernels when the check occurs in an atomic context. This issue may also affect other LSMs. This change avoids the unnecessary privilege check and resolves the sleeping function warning without any loss of information. Link: https://lkml.kernel.org/r/20241217142032.55793-1-acarmina@redhat.com Fixes: 3a6f33d ("mm/kmemleak: use %pK to display kernel pointers in backtrace") Signed-off-by: Alessandro Carminati <acarmina@redhat.com> Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Cc: Clément Léger <clement.leger@bootlin.com> Cc: Alessandro Carminati <acarmina@redhat.com> Cc: Eric Chanudet <echanude@redhat.com> Cc: Gabriele Paoloni <gpaoloni@redhat.com> Cc: Juri Lelli <juri.lelli@redhat.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Weißschuh <thomas.weissschuh@linutronix.de> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

…le_direct_reclaim() commit 6aaced5 upstream. The task sometimes continues looping in throttle_direct_reclaim() because allow_direct_reclaim(pgdat) keeps returning false. #0 [ffff80002cb6f8d0] __switch_to at ffff8000080095ac #1 [ffff80002cb6f900] __schedule at ffff800008abbd1c #2 [ffff80002cb6f990] schedule at ffff800008abc50c #3 [ffff80002cb6f9b0] throttle_direct_reclaim at ffff800008273550 #4 [ffff80002cb6fa20] try_to_free_pages at ffff800008277b68 #5 [ffff80002cb6fae0] __alloc_pages_nodemask at ffff8000082c4660 #6 [ffff80002cb6fc50] alloc_pages_vma at ffff8000082e4a98 #7 [ffff80002cb6fca0] do_anonymous_page at ffff80000829f5a8 #8 [ffff80002cb6fce0] __handle_mm_fault at ffff8000082a5974 #9 [ffff80002cb6fd90] handle_mm_fault at ffff8000082a5bd4 At this point, the pgdat contains the following two zones: NODE: 4 ZONE: 0 ADDR: ffff00817fffe540 NAME: "DMA32" SIZE: 20480 MIN/LOW/HIGH: 11/28/45 VM_STAT: NR_FREE_PAGES: 359 NR_ZONE_INACTIVE_ANON: 18813 NR_ZONE_ACTIVE_ANON: 0 NR_ZONE_INACTIVE_FILE: 50 NR_ZONE_ACTIVE_FILE: 0 NR_ZONE_UNEVICTABLE: 0 NR_ZONE_WRITE_PENDING: 0 NR_MLOCK: 0 NR_BOUNCE: 0 NR_ZSPAGES: 0 NR_FREE_CMA_PAGES: 0 NODE: 4 ZONE: 1 ADDR: ffff00817fffec00 NAME: "Normal" SIZE: 8454144 PRESENT: 98304 MIN/LOW/HIGH: 68/166/264 VM_STAT: NR_FREE_PAGES: 146 NR_ZONE_INACTIVE_ANON: 94668 NR_ZONE_ACTIVE_ANON: 3 NR_ZONE_INACTIVE_FILE: 735 NR_ZONE_ACTIVE_FILE: 78 NR_ZONE_UNEVICTABLE: 0 NR_ZONE_WRITE_PENDING: 0 NR_MLOCK: 0 NR_BOUNCE: 0 NR_ZSPAGES: 0 NR_FREE_CMA_PAGES: 0 In allow_direct_reclaim(), while processing ZONE_DMA32, the sum of inactive/active file-backed pages calculated in zone_reclaimable_pages() based on the result of zone_page_state_snapshot() is zero. Additionally, since this system lacks swap, the calculation of inactive/ active anonymous pages is skipped. crash> p nr_swap_pages nr_swap_pages = $1937 = { counter = 0 } As a result, ZONE_DMA32 is deemed unreclaimable and skipped, moving on to the processing of the next zone, ZONE_NORMAL, despite ZONE_DMA32 having free pages significantly exceeding the high watermark. The problem is that the pgdat->kswapd_failures hasn't been incremented. crash> px ((struct pglist_data *) 0xffff00817fffe540)->kswapd_failures $1935 = 0x0 This is because the node deemed balanced. The node balancing logic in balance_pgdat() evaluates all zones collectively. If one or more zones (e.g., ZONE_DMA32) have enough free pages to meet their watermarks, the entire node is deemed balanced. This causes balance_pgdat() to exit early before incrementing the kswapd_failures, as it considers the overall memory state acceptable, even though some zones (like ZONE_NORMAL) remain under significant pressure. The patch ensures that zone_reclaimable_pages() includes free pages (NR_FREE_PAGES) in its calculation when no other reclaimable pages are available (e.g., file-backed or anonymous pages). This change prevents zones like ZONE_DMA32, which have sufficient free pages, from being mistakenly deemed unreclaimable. By doing so, the patch ensures proper node balancing, avoids masking pressure on other zones like ZONE_NORMAL, and prevents infinite loops in throttle_direct_reclaim() caused by allow_direct_reclaim(pgdat) repeatedly returning false. The kernel hangs due to a task stuck in throttle_direct_reclaim(), caused by a node being incorrectly deemed balanced despite pressure in certain zones, such as ZONE_NORMAL. This issue arises from zone_reclaimable_pages() returning 0 for zones without reclaimable file- backed or anonymous pages, causing zones like ZONE_DMA32 with sufficient free pages to be skipped. The lack of swap or reclaimable pages results in ZONE_DMA32 being ignored during reclaim, masking pressure in other zones. Consequently, pgdat->kswapd_failures remains 0 in balance_pgdat(), preventing fallback mechanisms in allow_direct_reclaim() from being triggered, leading to an infinite loop in throttle_direct_reclaim(). This patch modifies zone_reclaimable_pages() to account for free pages (NR_FREE_PAGES) when no other reclaimable pages exist. This ensures zones with sufficient free pages are not skipped, enabling proper balancing and reclaim behavior. [akpm@linux-foundation.org: coding-style cleanups] Link: https://lkml.kernel.org/r/20241130164346.436469-1-snishika@redhat.com Link: https://lkml.kernel.org/r/20241130161236.433747-2-snishika@redhat.com Fixes: 5a1c84b ("mm: remove reclaim and compaction retry approximations") Signed-off-by: Seiji Nishikawa <snishika@redhat.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Hou Tao says: ==================== The patch set fixes several issues in bits iterator. Patch #1 fixes the kmemleak problem of bits iterator. Patch #2~#3 fix the overflow problem of nr_bits. Patch #4 fixes the potential stack corruption when bits iterator is used on 32-bit host. Patch #5 adds more test cases for bits iterator. Please see the individual patches for more details. And comments are always welcome. --- v4: * patch #1: add ack from Yafang * patch #3: revert code-churn like changes: (1) compute nr_bytes and nr_bits before the check of nr_words. (2) use nr_bits == 64 to check for single u64, preventing build warning on 32-bit hosts. * patch #4: use "BITS_PER_LONG == 32" instead of "!defined(CONFIG_64BIT)" v3: https://lore.kernel.org/bpf/20241025013233.804027-1-houtao@huaweicloud.com/T/#t * split the bits-iterator related patches from "Misc fixes for bpf" patch set * patch #1: use "!nr_bits || bits >= nr_bits" to stop the iteration * patch #2: add a new helper for the overflow problem * patch #3: decrease the limitation from 512 to 511 and check whether nr_bytes is too large for bpf memory allocator explicitly * patch #5: add two more test cases for bit iterator v2: http://lore.kernel.org/bpf/d49fa2f4-f743-c763-7579-c3cab4dd88cb@huaweicloud.com ==================== Link: https://lore.kernel.org/r/20241030100516.3633640-1-houtao@huaweicloud.com Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Petr Machata says: ==================== mlxsw: Fixes In this patchset: - Tx header should be pushed for each packet which is transmitted via Spectrum ASICs. Patch #1 adds a missing call to skb_cow_head() to make sure that there is both enough room to push the Tx header and that the SKB header is not cloned and can be modified. - Commit b5b60bb ("mlxsw: pci: Use page pool for Rx buffers allocation") converted mlxsw to use page pool for Rx buffers allocation. Sync for CPU and for device should be done for Rx pages. In patches #2 and #3, add the missing calls to sync pages for, respectively, CPU and the device. - Patch #4 then fixes a bug to IPv6 GRE forwarding offload. Patch #5 adds a generic forwarding test that fails with mlxsw ports prior to the fix. ==================== Link: https://patch.msgid.link/cover.1729866134.git.petrm@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Disable strict aliasing, as has been done in the kernel proper for decades (literally since before git history) to fix issues where gcc will optimize away loads in code that looks 100% correct, but is _technically_ undefined behavior, and thus can be thrown away by the compiler. E.g. arm64's vPMU counter access test casts a uint64_t (unsigned long) pointer to a u64 (unsigned long long) pointer when setting PMCR.N via u64p_replace_bits(), which gcc-13 detects and optimizes away, i.e. ignores the result and uses the original PMCR. The issue is most easily observed by making set_pmcr_n() noinline and wrapping the call with printf(), e.g. sans comments, for this code: printf("orig = %lx, next = %lx, want = %lu\n", pmcr_orig, pmcr, pmcr_n); set_pmcr_n(&pmcr, pmcr_n); printf("orig = %lx, next = %lx, want = %lu\n", pmcr_orig, pmcr, pmcr_n); gcc-13 generates: 0000000000401c90 <set_pmcr_n>: 401c90: f9400002 ldr x2, [x0] 401c94: b3751022 bfi x2, x1, #11, #5 401c98: f9000002 str x2, [x0] 401c9c: d65f03c0 ret 0000000000402660 <test_create_vpmu_vm_with_pmcr_n>: 402724: aa1403e3 mov x3, x20 402728: aa1503e2 mov x2, x21 40272c: aa1603e0 mov x0, x22 402730: aa1503e1 mov x1, x21 402734: 940060ff bl 41ab30 <_IO_printf> 402738: aa1403e1 mov x1, x20 40273c: 910183e0 add x0, sp, #0x60 402740: 97fffd54 bl 401c90 <set_pmcr_n> 402744: aa1403e3 mov x3, x20 402748: aa1503e2 mov x2, x21 40274c: aa1503e1 mov x1, x21 402750: aa1603e0 mov x0, x22 402754: 940060f7 bl 41ab30 <_IO_printf> with the value stored in [sp + 0x60] ignored by both printf() above and in the test proper, resulting in a false failure due to vcpu_set_reg() simply storing the original value, not the intended value. $ ./vpmu_counter_access Random seed: 0x6b8b4567 orig = 3040, next = 3040, want = 0 orig = 3040, next = 3040, want = 0 ==== Test Assertion Failure ==== aarch64/vpmu_counter_access.c:505: pmcr_n == get_pmcr_n(pmcr) pid=71578 tid=71578 errno=9 - Bad file descriptor 1 0x400673: run_access_test at vpmu_counter_access.c:522 2 (inlined by) main at vpmu_counter_access.c:643 3 0x4132d7: __libc_start_call_main at libc-start.o:0 4 0x413653: __libc_start_main at ??:0 5 0x40106f: _start at ??:0 Failed to update PMCR.N to 0 (received: 6) Somewhat bizarrely, gcc-11 also exhibits the same behavior, but only if set_pmcr_n() is marked noinline, whereas gcc-13 fails even if set_pmcr_n() is inlined in its sole caller. Cc: stable@vger.kernel.org Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=116912 Signed-off-by: Sean Christopherson <seanjc@google.com>

jk-ozlabs added 3 commits October 22, 2015 16:49

watchdog/aspeed_wdt: Unify register names with the doc

d6ba1a3

Signed-off-by: Jeremy Kerr <jk@ozlabs.org>

watchdog/aspeed_wdt: Set system reset mode to 'full chip'

2f17119

Currently, the watchdog timer does nothing on expiry - the 'SoC system' reset type doesn't seem to have any effect. This change uses the 'full chip' reset type instead. Signed-off-by: Jeremy Kerr <jk@ozlabs.org>

shenki closed this Oct 23, 2015

jk-ozlabs deleted the openbmc/wdt branch October 28, 2015 01:00

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

Openbmc/wdt #5

Openbmc/wdt #5

jk-ozlabs commented Oct 22, 2015

shenki commented Oct 23, 2015

Openbmc/wdt #5

Openbmc/wdt #5

Conversation

jk-ozlabs commented Oct 22, 2015

shenki commented Oct 23, 2015